Fuel consumption and gas emissions of an automatic transmission vehicle following simple eco-driving instructions on urban roads

Following eco-driving instructions can reduce fuel consumption between 5 to 20% on urban roads with manual cars. The majority of Australian cars have an automatic transmission gear-box. It is therefore of interest to verify whether current eco-driving instructions are e cient for such vehicles. In this pilot study, participants (N=13) drove an instrumented vehicle (Toyota Camry 2007) with an automatic transmission. Fuel consumption of the participants was compared before and after they received simple eco-driving instructions. Participants drove the same vehicle on the same urban route under similar tra c conditions. We found that participants drove at similar speeds during their baseline and eco-friendly drives, and reduced the level of their accelerations and decelerations during eco-driving. Fuel consumption decreased for the complete drive by 7%, but not on the motorway and inclined sections of the study. Gas emissions were estimated with the VT-micro model, and emissions of the studied pollutants (CO2, CO, NOX and HC) were reduced, but no di erence was observed for CO2 on the motorway and inclined sections. The di erence for the complete lap is 3% for CO2. We have found evidence showing that simple eco-driving instructions are e cient in the case of automatic transmission in an urban environment, but towards the lowest values of the spectrum of fuel consumption reduction from the di erent eco-driving studies.

Isolation and characterization of biofumigant from leaves of Lantana camara for control of stored grain insect pests

Due to environmental concerns, health hazards to man and the evolution of resistance in insect pests, there have been constant efforts to discover newer insecticides both from natural sources and by chemical synthesis. Natural sources for novel molecules hold promise in view of their eco-friendly nature, selectivity and mammalian safety. We have isolated one natural bioactive molecule from the leaves of Lantana camara named Coumaran, based on various physical-chemical and spectroscopic techniques (IR, H-1 NMR, C-13 NMR and MS). Coumaran is highly toxic and very low concentration is needed for control of stored product insects. This molecule has potent grain protectant potential and caused significant reduction in F1 progeny of all the three species in the treated grain and the progeny was completely suppressed at 30 mu g/l. The differences in germination between the control and treated grains were not significant. The lack of any adverse effect of Coumaran on the seed germination is highly desirable for a grain protectant, becoming a potential source of biofumigant for economical and environmentally friendly pest control strategies against stored grain pests during storage of grains or pulses. (C) 2013 Elsevier B.V. All rights reserved.

Industrial development and land use/cover change and their effects on local environment: a case study of Changshu in eastern coastal China

The interactions among industrial development, land use/cover change (LUCC), and environmental effects in Changshu in the eastern coastal China were analyzed using high-resolution Landsat TM data in 1990, 1995, 2000, and 2006, socio-economic data and water environmental quality monitoring data from research institutes and governmental departments. Three phases of industrial development in Changshu were examined (i.e., the three periods of 1990 to 1995, 1995 to 2000, and 2000 to 2006). Besides industrial development and rapid urbanization, land use/cover in Changshu had changed drastically from 1990 to 2006. This change was characterized by major replacements of farmland by urban and rural settlements, artificial ponds, forested and constructed land. Industrialization, urbanization, agricultural structure adjustment, and rural housing construction were the major socio-economic driving forces of LUCC in Changshu. In addition, the annual value of ecosystem services in Changshu decreased slightly during 1990-2000, but increased significantly during 2000-2006. Nevertheless, the local environmental quality in Changshu, especially in rural areas, has not yet been improved significantly. Thus, this paper suggests an increased attention to fully realize the role of land supply in adjustment of environment-friendly industrial structure and urban-rural spatial restructuring, and translating the land management and environmental protection policies into an optimized industrial distribution and land-use pattern.

Las infraestructuras de recarga y el despegue del vehículo eléctrico.

Este trabajo revisa la evolución y estado actual de la automoción eléctrica; analiza las ventajas ambientales, de eficiencia energética y de costes del motor eléctrico frente al de combustión interna; y presenta como limitaciones para el uso del vehículo eléctrico, el desarrollo actual de las baterías recargables y la lenta implantación de electrolineras. Con el objetivo de contribuir al desarrollo de una actividad económica respetuosa con el medio ambiente y basada en nuevas tecnologías, se proyecta, a partir de experiencias previas, una instalación de puntos de recarga para una ciudad de 50.000 habitantes con un parque de 100 vehículos eléctricos que dispone de dos plazas de recarga rápida (poste trifásico 400V CA), siete plazas de recarga lenta (postes monofásicos 230V CA) y de 50 módulos fotovoltaicos que producen diariamente la energía equivalente a la recarga lenta de un vehículo en los meses fríos y de dos en los meses cálidos.

Sustainable binders for concrete: a structured approach from waste screening to binder composition development

Worldwide, the building sector requires the production of 4 billion tonnes of cement annually, consuming more than 40% of global energy. Alkali activated “cementless” binders have recently emerged as a novel eco-friendly construction material with a promising potential to replace ordinary Portland cement. These binders consist of a class of inorganic polymer formed mainly by the reaction between an alkaline solution and an aluminosilicate source. Precursor materials for this reaction can be found in secondary material streams from different industrial sectors, from energy to agro-alimentary. However, the suitability of these materials in developing the polymerisation reaction must be assessed through a detailed chemical and physical characterisation, ensuring the availability of required chemical species in the appropriate quantity and physical state. Furthermore, the binder composition needs to be defined in terms of proper alkali activation dosages, water content in the mix, and curing conditions. The mix design must satisfy mechanical requirements and compliance to desired engineering properties (workability, setting time) for ensuring the suitability of the binder in replacing Portland cement in concrete applications. This paper offers a structured approach for the development of secondary material-based binders, from their identification to mix design and production procedure development. Essential features of precursor material can be determined through chemical and physical characterisation methods and advanced microscope techniques. Important mixing parameters and binder properties requirements are examined and some examples of developed binders are reported.

Laccase-assisted bio-grafting of polyhydroxy-alkanoates (PHAs) onto the ethyl cellulose (EC) backbone

In the present study, a novel enzyme-based methodology for grafting Polyhydroxyalkanoates (PHAs) onto the ethyl cellulose (EC) as a backbone polymer was developed. Laccase assisted copolymerization was carried out under mild and eco-friendly reaction conditions. The resulting homogeneous composite membranes were characterized by Fourier-transformed infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC), and Atomic Force Microscopy (AFM). The FTIR spectra of pure PHAs and PHAs containing graft composites (PHAs-g-EC) showed their strong characteristic bands at 1721 cm1, 1651 cm-1 and 1603 cm-1 respectively. Other accompanying bands in the range of 900-1300 cm-1 correspond to C=O vibration and C-O-C bond stretching, which could be contributed from PHAs and EC, respectively. The high intensity of the 3358 cm-1 band in the graft composite may have corresponded to the degradation of the carboxylic group from PHAs and also showed an increase of hydrogen-bonded groups at that distinct band region. The morphology was examined by SEM, which showed the well dispersed PHAs crystals in the backbone polymer of EC. XRD pattern for PHAs showed distinct peaks at 2-Theta values of 28o, 32o, 34o, 39o, 46o, 57o, 64o, 78o and 84o that represent the crystalline nature of PHAs. In comparison with those of neat PHAs, the degree of crystallinity for PHAs-g-EC decreased and this reduction is mainly because of the new cross-linking of PHAs within the EC backbone that changes the morphology and destroys the crystallites. Improved mechanical properties were observed for the PHAs-g-EC as compared to the individual components due to the impregnation of EC as reinforcement into the PHAs matrix. Improved mechanical strength enhanced thermal properties, along with low crystallinity of the present PHAs-g-EC suggesting its potential for various industrial and bio-medical applications.

Spray Pyrolysed Tin Chalcogenide Thin Films: Optimization of optoelectronic properties of SnS for possible photovoltaic application as an absorber layer

In the early 19th century, industrial revolution was fuelled mainly by the development of machine based manufacturing and the increased use of coal. Later on, the focal point shifted to oil, thanks to the mass-production technology, ease of transport/storage and also the (less) environmental issues in comparison with the coal!! By the dawn of 21st century, due to the depletion of oil reserves and pollution resulting from heavy usage of oil the demand for clean energy was on the rising edge. This ever growing demand has propelled research on photovoltaics which has emerged successful and is currently being looked up to as the only solace for meeting our present day energy requirements. The proven PV technology on commercial scale is based on silicon but the recent boom in the demand for photovoltaic modules has in turn created a shortage in supply of silicon. Also the technology is still not accessible to common man. This has onset the research and development work on moderately efficient, eco-friendly and low cost photovoltaic devices (solar cells). Thin film photovoltaic modules have made a breakthrough entry in the PV market on these grounds. Thin films have the potential to revolutionize the present cost structure of solar cells by eliminating the use of the expensive silicon wafers that alone accounts for above 50% of total module manufacturing cost.Well developed thin film photovoltaic technologies are based on amorphous silicon, CdTe and CuInSe2. However the cell fabrication process using amorphous silicon requires handling of very toxic gases (like phosphene, silane and borane) and costly technologies for cell fabrication. In the case of other materials too, there are difficulties like maintaining stoichiometry (especially in large area films), alleged environmental hazards and high cost of indium. Hence there is an urgent need for the development of materials that are easy to prepare, eco-friendly and available in abundance. The work presented in this thesis is an attempt towards the development of a cost-effective, eco-friendly material for thin film solar cells using simple economically viable technique. Sn-based window and absorber layers deposited using Chemical Spray Pyrolysis (CSP) technique have been chosen for the purpose

Development and microwave characterization of selected biocompatible materials and conducting polymers

The 20th century witnessed the extensive use of microwaves in industrial, scientific and medical fields. The major hindrance to many developments in the ISM field is the lack of knowledge about the effect of microwaves on materials used in various applications. The study of the interaction of microwaves with materials demanded the knowledge of the dielectric properties of these materials. However, the dielectric properties of many of these materials are still unknown or less studied. This thesis is an effort to shed light into the dielectric properties of some materials which are used in medical, scientific and industrial fields. Microwave phantoms are those materials used in microwave simulation applications. Effort has been taken to develop and characterize low cost, eco-friendly phantoms from Biomaterials and Bioceramics. The interaction of microwaves with living tissues paved way to the development of materials for electromagnetic shielding. Materials with good conductivity/absorption properties could be used for EMI shielding applications. Conducting polymer materials are developed and characterized in this context. The materials which are developed and analyzed in this thesis are Biomaterials, Bioceramics and Conducting polymers. The use of materials of biological origin in scientific and medical applications provides an eco-friendly pathway. The microwave characterization of the materials were done using cavity material perturbation method. Low cost and ecofriendly biomaterial films were developed from Arrowroot and Chitosan. The developed films could be used in applications such as microwave phantom material, capsule material in pharmaceutical applications, trans-dermal patch material and eco-friendly Band-Aids. Bioceramics with better bioresorption and biocompatibility were synthesized. Bioceramics such as Hydroxyapatite, Beta tricalcium phosphate and Biphasic Calcium Phosphate were studied. The prepared bioceramics could be used as phantom material representing Collagen, Bone marrow, Human abdominal wall fat and Human chest fat. Conducting polymers- based on Polyaniline, are developed and characterized. The developed materials can be used in electromagnetic shielding applications such as in anechoic chambers, transmission cables etc

Utilization of aquatic macrophyte Spirodela polyrhiza as phytotoxicological assessment and phytoremediation tool in selected polluted wetland sites in Ernakulam district

One of the objectives of the current investigation was to evaluate the effectiveness of Spirodela polyrhiza to remove heavy metals and other contaminants from the water samples collected from wetland sites of Eloor and Kannamaly under controlled conditions .The results obtained from the current study suggest that the test material S. polyrrhiza should be used in the biomonitoring and phytoremediation of municipal, agricultural and industrial effluents because of their simplicity, sensitivity and cost-effectiveness. The study throws light on the potential of this plant which can be used as an assessment tool in two diverse wetland in Ernakulum district. The results show the usefulness of combining physicochemical analysis with bioassays as such approach ensures better understanding of the toxicity of chemical pollutants and their influence on plant health. The results shows the suitability of Spirodela plant for surface water quality assessment as all selected parameters showed consistency with respect to water samples collected over a 3-monitoring periods. Similarly the relationship between the change in exposure period (2, 4 and 8 days) with the parameters were also studied in detail. Spirodela are consistent test material as they are homogeneous plant material; due to predominantly vegetative reproduction. New fronds are formed by clonal propagation thus, producing a population of genetically homogeneous plants. The result is small variability between treated individuals. It has been observed that phytoremediation of water samples collected from Eloor and Kannamaly using the floating plant system is a predominant method which is economic to construct, requires little maintenance and eco friendly.

Diagnóstico y propuesta para la implementación de un departamento de mercadeo en la multinacional Rhodia Colombia 2012

Este trabajo de grado se realizó con el fin de hacer un diagnóstico para evaluar y analizar la estructuración un departamento de mercadeo en Rhodia Colombia, teniendo en cuenta la coyuntura actual de la compañía y su intensión expansionista en los mercados de industria química en Colombia. Para lograr esta intención es necesario que este departamento pueda llevar procesos de investigación alineados con las estrategias de Marketing que desarrolla Rhodia Brasil, y así mismo brindar a los gerentes comerciales información valiosa para realizar esfuerzos en los mercados potenciales de Rhodia y a los mercados en que se ha posicionado Solvay en Colombia. Las expectativas se fundamentan en lograr establecer un departamento de Mercadeo estructurado donde se lleven a cabo procesos de Marketing “Business to Business” en pro de buscar nuevas oportunidades de mercado, fortalecer la presencia comercial en nichos de mercado estratégicos y monitorear los mercados de la compañía para anticiparse ante los sucesos coyunturales donde interactúan los productos de Rhodia en Colombia.

Modelo de recolección de residuos sólidos botellas plásticas y latas utilizando como aliado el sistema de transporte masivo en Bogotá

En las grandes ciudades, la disposición de residuos se ha convertido en un problema ambiental de magnitud mundial con impacto negativo por el manejo inadecuado de los residuos sólidos diarios. El propósito es utilizar el sistema de transporte publico de Bogotá (Transmilenio) como punto de recolección de botellas plásticas y latas, para crear un proyecto de responsabilidad ambiental el cual tendrá resultados positivos a nivel cultural, social, y a largo plazo, financieramente. A través del estudio de diferentes propuestas tanto locales como internacionales, fueron identificados los principales factores de éxito de estos proyectos los cuales se incluyeron para adecuar la presente propuesta para la ciudad de Bogotá teniendo en cuenta sus actuales condiciones. Después de identificar las características requeridas para Bogotá, se realizó un estudio demográfico para poder saber cuántos ciudadanos estarían dispuestos a participar. Como resultado, muchos pasajeros de Transmilenio esperan una retribución económica en el costo del pasaje del sistema. La prueba piloto se diseñó de acuerdo con la cantidad de envases recolectados, incluyendo el tipo de vehículos, como también la cantidad de personas y maquinas necesarias para el éxito del proyecto. Con la propuesta del proyecto completa, se realiza una evaluación financiera y económica para identificar los costos y gastos. La conclusión final de esta propuesta es que el modelo propuesto puede ser aplicado en Bogotá dadas sus características. Los beneficios sociales y ambientales también se destacan, como también el cambio cultural por parte de los ciudadanos hacia las prácticas ecológicas.

Different implications for enterprises of an organic production

This paper reviews the concept of “organic”, its meaning and emphasizes a comparison with conventional goods. It develops the background of organic goods in the past 20 years, quotations different definitions of organic and developing a main definition. Also it states certain criteriab and variables in order to develop a deeper business analysis. And it has the objective to define the advantages, disadvantages, key points and strategies for companies that want to venture an organic production, and if it’s recommendable to pursue. After a cross case and SWOT analysis it is possible to determine that depending of the core strategy and type of company if an enterprise can decide to venture the organic market.

Learning from sustainable landscapes of death in Bali : landscape planning and Tri Hita Karana

Landscape planning in many countries is predicated upon on fulfilling the functions for human living objectives. Many land use practices have been plotted for living, busines~, trading, industrial, farming as well as providing places for dead people primarily through cemeteries. Research in Palm Beach County, FL, has demonstrated the need to plan for 30 years of demand of land use functions to service death (Coutts, Basmaj ian et al. 20 I I). Coutts et al assert that planners are required and responsible for the planning of funeral necessities. Therefore, the protection of landscapes of death is an important consideration in the planning of landscapes. Bali is popular with its beautiful landscape, hospitality, and traditional architecture as demonstrating the integrity between human, environment and God, as expressed in the Balinese Tri Hita Karana concept. Balinese commemorate life from birth to death through their traditional ceremonies which informs their traditional cultural landscape. One of the most important landscapes, which cannot be separated fi·om Balinese life are graveyards which are used for deceased ceremonies. This landscape is an integral part of traditional village patterns across Bali. Culturally, Balinese people have their own traditional cremation ceremony which is call the Ngaben Ceremony. The Ceremony takes place in graveyards and thereupon ashes are placed in the sea waters surrounding Bali. An interesting point of planning in Bali is how to enable eco-friendly interment extensions to villages. This is occurring because of the increasing number of corpses that require cremation thus necessitating no accretions in land provision of graveyards. This research investigates the landscape of death in Bali expressed in its traditional values in the area of planning which implicate sustainable environments and land conservation topics. Other functions of graveyards, as noted by Strangstad ( 1988), include ceremonial and their role as educational tools for history lessons, art, sociology, geology, English lessons, as well as for scavenger hunts.

O uso de bambu e metal clay no design de jóias de arte

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Development of sustainable, innovative and energy-efficient concrete, based on the integration of all-waste materials: SUS-CON panels for building applications

The building sector requires the worldwide production of 4 billion tonnes of cement annually, consuming more than 40% of global energy and accounting for about 8% of the total CO2 emissions. The SUS-CON project aimed at integrating waste materials in the production cycle of concrete, for both ready-mixed and pre-cast applications, resulting in an innovative light-weight, ecocompatible and cost-effective construction material, made by all-waste materials and characterized by enhanced thermal insulation performance and low embodied energy and CO2. Alkali activated “cementless” binders, which have recently emerged as eco-friendly construction materials, were used in conjunction with lightweight recycled aggregates to produce sustainable concrete for a range of applications. This paper presents some results from the development of a concrete made with a geopolymeric binder (alkali activated fly ash) and aggregate from recycled mixed plastic. Mix optimisation was achieved through an extensive investigation on production parameters for binder and aggregate. The mix recipe was developed for achieving the required fresh and hardened properties. The optimised mix gave compressive strength of about 7 MPa, flexural strength of about 1.3 MPa and a thermal conductivity of 0.34 W/mK. Fresh and hardened properties were deemed suitable for the industrial production of precast products. Precast panels were designed and produced for the construction of demonstration buildings. Mock-ups of about 2.5 x 2.5 x 2.5 m were built at a demo park in Spain both with SUS-CON and Portland cement concrete, monitoring internal and external temperatures. Field results indicate that the SUS-CON mock-ups have better insulation. During the warmest period of the day, the measured temperature in the SUS-CON mock-ups was lower.