Characterization of nickel-niobium composite electrocoatings

The electrodeposition of nickel based composites is been performed in order to improve properties of nickel layers, such as hardness, wear resistance, lubrication, corrosion resistance and catalytic activity. In the present work Nb powders (20 mu m average size) and Ni were codeposited on 1020 carbon steel by galvanostatic electrolysis of Watts bath, using 10, 20 and 40 mA/cm(2) cathodic current density and 240, 400 and 550 rpm electrolyte stirring rate. The morphology and texture of the coatings, Nb incorporated volume fraction, microhardness, adhesion to the substrate and corrosion behavior were evaluated. The Ni-Nb composite layers presented a rough morphology with randomly oriented Ni grains, whereas pure Ni coatings were smooth and showed highly preferred orientation in the [110] or [100] direction. The volume fraction of Nb in the composites determined by image analysis ranged from 8.5 to 19%. The 400 rpm stirring rate led to the highest Nb content (16 to 19016) for all current densities investigated The microhardness of the composite layers was higher than that of pure Ni coatings due to refining of Ni grains induced by incoporation of Nb particles. The adhesion of the coatings estimated qualitatively by bend test was found satisfactory. The Ni-Nb composites presented lower corrosion rate than Ni coatings in both 3% NaCl and 20% H2SO4 solutions.

TiAlN coatings deposited by triode magnetron sputtering varying the bias voltage

TiAlN films were deposited on AISI O1 tool steel using a triode magnetron sputtering system. The bias voltage effect on the composition, thickness, crystallography, microstructure, hardness and adhesion strength was investigated. The coatings thickness and elemental composition analyses were carried out using scanning electron microscopy (SEM) together with energy dispersive X-ray (EDS). The re-sputtering effect due to the high-energy ions bombardment on the film surface influenced the coatings thickness. The films crystallography was investigated using X-ray diffraction characterization. The X-ray diffraction (XRD) data show that TiAlN coatings were crystallized in the cubic NaCl B1 structure, with orientations in the {111}, {200} {220} and {311} crystallographic planes. The surface morphology (roughness and grain size) of TiAlN coatings was investigated by atomic force microscopy (AFM). By increasing the substrate bias voltage from -40 to -150 V, hardness decreased from 32 GPa to 19 GPa. Scratch tester was used for measuring the critical loads and for measuring the adhesion. (C) 2011 Elsevier B. V. All rights reserved.

Filling and wetting transitions of nematic liquid crystals on sinusoidal substrates

Close to sinusoidal substrates, simple fluids may undergo a filling transition, in which the fluid passes from a dry to a filled state, where the interface remains unbent but bound to the substrate. Increasing the surface field, the interface unbinds and a wetting transition occurs. We show that this double-transition sequence may be strongly modified in the case of ordered fluids, such as nematic liquid crystals. Depending on the preferred orientation of the nematic molecules at the structured substrate and at the isotropic-nematic interface, the filling transition may not exist, and the fluid passes directly from a dry to a complete-wet state, with the interface far from the substrate. More interestingly, in other situations, the complete wetting transition may be prevented, and the fluid passes from a dry to a filled state, and remains in this configuration, with the interface always attached to the substrate, even for very large surface fields. Both transitions are observed only for a same substrate in a narrow range of amplitudes.

Study of vanadium doped ZnO films prepared by dc reactive magnetron sputtering at different substrate temperatures

ZnO films doped with vanadium (ZnO:V) have been prepared by dc reactive magnetron sputtering technique at different substrate temperatures (RT–500 C). The effects of the substrate temperature on ZnO:V films properties have been studied. XRD measurements show that only ZnO polycrystalline structure has been obtained, no V2O5 or VO2 crystal phase can be observed. It has been found that the film prepared at low substrate temperature has a preferred orientation along the (002) direction. As the substrate temperature is increased, the (002) peak intensity decreases. When the substrate temperature reaches the 500 C, the film shows a random orientation. SEM measurements show a clear formation of the nano-grains in the sample surface when the substrate temperature is higher than 400 C. The optical properties of the films have been studied by measuring the specular transmittance. The refractive index has been calculated by fitting the transmittance spectra using OJL model combined with harmonic oscillator.

Growth of the [110] oriented TiO2 nanorods on ITO substrates by sputtering technique for dye-sensitized solar cells

TiO2 films have been deposited on ITO substrates by dc reactive magnetron sputtering technique. It has been found that the sputtering pressure is a very important parameter for the structure of the deposited TiO2 films. When the pressure is lower than 1 Pa, the deposited has a dense structure and shows a preferred orientation along the [101] direction. However, the nanorod structure has been obtained as the sputtering pressure is higher than 1 Pa. These nanorods structure TiO2 film shows a preferred orientation along the [110] direction. The x-ray diffraction and the Raman scattering measurements show both the dense and the nanostructure TiO2 films have only an anatase phase, no other phase has been obtained. The results of the SEM show that these TiO2 nanorods are perpendicular to the ITO substrate. The TEM measurement shows that the nanorods have a very rough surface. The dye-sensitized solar cells (DSSCs) have been assembled using these TiO2 nanorod films prepared at different sputtering pressures as photoelectrode. And the effect of the sputtering pressure on the properties of the photoelectric conversion of the DSSCs has been studied.

Adaptação cultural e contributo para a validação da pain attitudes and believes scale for physiotherapists (PABS-PT) para a população de fisioterapeutas portugueses

RESUMO: Introdução: Vários estudos têm encontrado evidência para a relação entre as crenças e atitudes dos profissionais de saúde, a sua abordagem de tratamento, referida como orientada segundo o modelo biomédico ou modelo biopsicossocial (Bishop, 2008; Mutsaers, 2012), e os resultados obtidos. É sugerido que, no tratamento da dor lombar crónica, os profissionais que orientam o seu raciocínio e prática segundo o modelo biomédico, tendem a obter piores resultados quando comparados com os obtidos pelos profissionais que orientam o seu raciocínio e prática segundo uma abordagem biopsicossocial. Esta área de estudo tem salientado a importância de desenhar instrumentos capazes de identificar a orientação preferencial dos profissionais de saúde no tratamento da dor crónica de natureza músculo-esquelética, entre os quais se encontra a “Pain Attitudes and Beliefs Scale for Physiotherapists” (PABS-PT). Objetivo: Adaptar culturalmente a PABS-PT para a população de fisioterapeutas portugueses que intervêm em utentes com dor (lombar) crónica, e contribuir para a sua validação Metodologia: A versão original (língua inglesa) do PABS-PT foi adaptada para a língua e cultura portuguesas, através das etapas definidas nas normas orientadoras estabelecidas para este processo (Beaton et al., 2002; MAPI Institute, 2001). A avaliação das propriedades psicométricas da versão portuguesa foi realizada com recurso a uma amostra de 202 fisioterapeutas e estudantes finalistas do curso de licenciatura em Fisioterapia. Inicialmente foi realizada a análise fatorial exploratória da escala através do método das componentes principais. Posteriormente avaliou-se a consistência interna das componentes obtidas com recurso ao alpha de Cronbach (α). Para analisar a validade de constructo foram correlacionadas as componentes obtidas com a versão portuguesa da “Health Care Providers’ Pain and Impairment Relationship Scale” (HC-PAIRS), recorrendo ao cálculo do coeficiente de Spearman. Resultados: O processo de adaptação cultural não revelou dificuldades importantes sendo considerado que a versão portuguesa da PABS-PT é de fácil compreensão e preenchimento, e os seus itens adequados para avaliar as crenças e atitudes dos fisioterapeutas portugueses relativas à intervenção na dor crónica músculo-esquelética. Os resultados revelaram uma estrutura fatorial de duas componentes, identificadas com as componentes da escala original que explicam 30,96% da variância total. A consistência interna encontrada é boa, para a componente biomédica (α de Cronbach = 0,826), mas muito fraca para a componente biopsicossocial (α de Cronbach= 0,589). Relativamente à validade convergente e discriminativa, foi encontrada uma associação estatisticamente significativa e positiva, entre as componentes 1 (biomédica) da versão nportuguesa da PABS e a HC-PAIRS (Rs = 0,481, p≤ 0,005), e negativa, fraca e significativa entre a pontuação total da componente 2 (biopsicossocial) e a HC-PAIRS (Rs = -0,038, p=0,612). Conclusão: A versão portuguesa do PABS-PT é de fácil compreensão e aparenta ser um instrumento válido para a medição da orientação preferencial dos fisioterapeutas, relativamente às suas atitudes e crenças na avaliação e tratamento de utentes com dor crónica de natureza músculo-esquelética. No entanto, a componente biopsicossocial requer uma análise mais aprofundada para que possa, com rigor, ser utilizada na definição de uma orientação preferencialmente biopsicossocial.--------------ABSTRACT: Introduction: Previous studies have found a relation between the beliefs and attitudes of health professionals, their treatment approach, which can follows a biomedical or a biopsychosocial orientation (Bishop, 2008; Mutsaers, 2012), and the outcomes obtained. Therefore, is suggested that the professionals who tend to approach chronic low back pain patients according to the biomedical model have worse outcomes than professionals who use a biopsychosocial approach in there clinical reasoning. This research field has highlighted the importance of developing measures capable of identifying the preferred orientation of health professionals in the treatment of chronic pain of musculoskeletal nature, including the “Pain Attitudes and Beliefs Scale for Physiotherapists” (PABS-PT). Objective: To cross culturally adapt and validate the PABS-PT for the Portuguese population of physiotherapists. Methodology: The original version (English version) of the PABS-PT was adapted to the Portuguese language and culture, through the guidelines established for these processes (Beaton et al., 2002; MAPI Institute, 2001). The psychometric evaluation of the Portuguese version was carried out on a sample of 202 p physiotherapist and final year students of the physiotherapy course. Initially, an exploratory factorial analysis was performed through the method of the main components. Then, the internal consistence of the main components was evaluated using the Cronbach’s alpha (α). The convergent construct validity was analysed through the correlation between the obtained components of PABS-PT and the Health Care Provider’s Pain and Impairment Relationship Scale (HC-PAIRS), using the Spearmen correlation coefficient. Results: No major difficulties were found during the cultural adaptation process of PABS-PT to Portugal, which means that the Portuguese version is easy to understand and fulfill, and items are appropriated to evaluate the beliefs and attitudes of the Portuguese physiotherapists who treat chronic pain of musculoskeletal origins. The results revealed a factorial structure of two components, as the original scale, explaining 30,96% of the total variance. Internal consistence results were good, for the biomedical component (Cronbach’s α = 0,826), but very weak for the biopsychosocial componente (Cronbach’s α = 0,589). Relatively to convergent and discriminative validity, a statistically significant association was found, between the components 1 (biomedical) of the Portuguese version of PABS-PT and the HC-PAIRS (Rs= 0,481, p≤ 0,005) and negative, weak and significant between the total score of component 2 (biopsychosocial) and the HC-PAIRS (Rs = -0,038, p=0,612). Conclusion: The Portuguese Version of PABS-PT is easy to understand and seems to be a valid instrument to measure the attitudes and beliefs of physiotherapists in the management of patients with chronic low back pain. However, the biopsychosocial component requires a further deep analysis to examine a preferable biopsychosocial orientation.

Microfabrics in carbonate mylonites along a large-scale shear zone (Helvetic Alps)

Carbonate mylonites with varying proportions of second-phase minerals were collected at positions of increasing metamorphic grade along the basal thrust of the Morcles nappe (Helvetic nappes, Switzerland). Variations of temperature, stress, and strain rate, changes in chemistry of solid and fluid phases, and differing degrees of strain localization and annealing were tracked by measuring the shapes, mean sizes, and size distributions of both matrix and second-phase grains, as well as crystal preferred orientation (CPO) of the matrix. Field structures suggest that strain rate was constant along the fault. The mean and distribution of the calcite grain sizes were affected most profoundly by temperature: Increased temperature, presumably accompanied by decreased stress, correlated with larger mean sizes and wider size distributions. At a given location, the matrix grains in mylonites with more second-phase particles are, on average, smaller, have narrower size distributions, and have more elongate shapes. For example, mylonites with 50 vol.% of second phases have matrix grain sizes half that of pure mylonites. Changes in calcite chemistry and the presence of synkinematic fluids seemed to influence microfabric only weakly. Temporal variations in conditions, such as exhumation-induced cooling, apparently provoke changes in temperature, stress, and strain rate along the nappe. These changes result in further strain localization during retrograde conditions and cause the grain size to be reduced by an additional 50%. The matrix CPO strengthens with increasing temperature or strain, but weakens and rotates with increasing second-phase content, These fabric changes suggest differing rates of grain growth, grain size reduction, and development of CPO owing to variations in the deformation conditions and, perhaps, mechanisms. To interpret natural mylonite structures or to extrapolate mechanical data to natural situations requires careful characterization of the microfabric, and, in particular, second-phase minerals. (c) 2007 Elsevier B.V, All rights reserved.

Influence of RF power on the properties of sputtered ZnO:Al thin films

Transparent conducting, aluminium doped zinc oxide thin films (ZnO:Al) were deposited by radio frequency (RF) magnetron sputtering. The RF power was varied from 60 to 350Wwhereas the substrate temperature was kept at 160 °C. The structural, electrical and optical properties of the as-deposited films were found to be influenced by the deposition power. The X-ray diffraction analysis showed that all the films have a strong preferred orientation along the [001] direction. The crystallite size was varied from 14 to 36 nm, however no significant change was observed in the case of lattice constant. The optical band gap varied in the range 3.44-3.58 eV. The lowest resistivity of 1.2×10 -3Vcm was shown by the films deposited at 250 W. The mobility of the films was found to increase with the deposition power.

Influence de la locomotion sur la morphologie de l’articulation distale de l’humérus chez les hominoïdes

La masse corporelle et la direction des charges sont des facteurs qui peuvent modifier la morphologie des surfaces articulaires qui sont généralement orientées et de taille suffisante pour résister aux charges chroniques. Chez les hominoïdes, les forces de tension et compression, générées par la locomotion, sont transmises à travers l’articulation du coude. Ces espèces ont une morphologie similaire de l’extrémité distale de l’humérus, mais qui présente certaines différences selon la taille des individus et leurs modes de locomotion. Ce projet tente de caractériser plus exhaustivement cette variation en analysant la largeur des surfaces articulaires ainsi que leur position et orientation par rapport à l’axe long de la diaphyse. La prémisse de ce mémoire est que, chez les espèces plus arboricoles, la morphologie de l’articulation distale de l’humérus répond aux stress transverses générés par les puissants muscles fléchisseurs du poignet et des doigts qui traversent le coude obliquement. En revanche, les espèces plus terrestres présentent une morphologie permettant de résister aux forces axiales provenant du contact avec le sol. Des coordonnées tridimensionnelles et des mesures linéaires ont été recueillies sur un échantillon squelettique d’individus des genres Homo, Pan, Gorilla et Pongo. Les résultats obtenus révèlent que l’orientation et la position des surfaces articulaires de la trochlée correspondent aux types de locomotion, or leur taille et celle et du capitulum semblent être influencées par la taille des individus. L’hypothèse suggérant que les stress reliés aux divers modes de locomotion des hominoïdes influencent la morphologie de l’articulation distale de l’humérus est donc supportée.

Codage de l’information visuelle par la plasticité et la synchronisation des réponses neuronales dans le cortex visuel primaire du chat

Les systèmes sensoriels encodent l’information sur notre environnement sous la forme d’impulsions électriques qui se propagent dans des réseaux de neurones. Élucider le code neuronal – les principes par lesquels l’information est représentée dans l’activité des neurones – est une question fondamentale des neurosciences. Cette thèse constituée de 3 études (E) s’intéresse à deux types de codes, la synchronisation et l’adaptation, dans les neurones du cortex visuel primaire (V1) du chat. Au niveau de V1, les neurones sont sélectifs pour des propriétés comme l’orientation des contours, la direction et la vitesse du mouvement. Chaque neurone ayant une combinaison de propriétés pour laquelle sa réponse est maximale, l’information se retrouve distribuée dans différents neurones situés dans diverses colonnes et aires corticales. Un mécanisme potentiel pour relier l’activité de neurones répondant à des items eux-mêmes reliés (e.g. deux contours appartenant au même objet) est la synchronisation de leur activité. Cependant, le type de relations potentiellement encodées par la synchronisation n’est pas entièrement clair (E1). Une autre stratégie de codage consiste en des changements transitoires des propriétés de réponse des neurones en fonction de l’environnement (adaptation). Cette plasticité est présente chez le chat adulte, les neurones de V1 changeant d’orientation préférée après exposition à une orientation non préférée. Cependant, on ignore si des neurones spatialement proches exhibent une plasticité comparable (E2). Finalement, nous avons étudié la dynamique de la relation entre synchronisation et plasticité des propriétés de réponse (E3). Résultats principaux — (E1) Nous avons montré que deux stimuli en mouvement soit convergent soit divergent élicitent plus de synchronisation entre les neurones de V1 que deux stimuli avec la même direction. La fréquence de décharge n’était en revanche pas différente en fonction du type de stimulus. Dans ce cas, la synchronisation semble coder pour la relation de cocircularité dont le mouvement convergent (centripète) et divergent (centrifuge) sont deux cas particuliers, et ainsi pourrait jouer un rôle dans l’intégration des contours. Cela indique que la synchronisation code pour une information qui n’est pas présente dans la fréquence de décharge des neurones. (E2) Après exposition à une orientation non préférée, les neurones changent d’orientation préférée dans la même direction que leurs voisins dans 75% des cas. Plusieurs propriétés de réponse des neurones de V1 dépendent de leur localisation dans la carte fonctionnelle corticale pour l’orientation. Les comportements plus diversifiés des 25% de neurones restants sont le fait de différences fonctionnelles que nous avons observé et qui suggèrent une localisation corticale particulière, les singularités, tandis que la majorité des neurones semblent situés dans les domaines d’iso-orientation. (E3) Après adaptation, les paires de neurones dont les propriétés de réponse deviennent plus similaires montrent une synchronisation accrue. Après récupération, la synchronisation retourne à son niveau initial. Par conséquent, la synchronisation semble refléter de façon dynamique la similarité des propriétés de réponse des neurones. Conclusions — Cette thèse contribue à notre connaissance des capacités d’adaptation de notre système visuel à un environnement changeant. Nous proposons également des données originales liées au rôle potentiel de la synchronisation. En particulier, la synchronisation semble capable de coder des relations entre objets similaires ou dissimilaires, suggérant l’existence d’assemblées neuronales superposées.

“Design and Development of Coplanar Strip Fed Planar Antennas”

With the recent progress and rapid increase in the field of communication, the designs of antennas for small mobile terminals with enhanced radiation characteristics are acquiring great importance. Compactness, efficiency, high data rate capacity etc. are the major criteria for the new generation antennas. The challenging task of the microwave scientists and engineers is to design a compact printed radiating structure having broadband behavior along with good efficiency and enhanced gain. Printed antenna technology has received popularity among antenna scientists after the introduction of planar transmission lines in mid-seventies. When we view the antenna through a transmission line concept, the mechanism behind any electromagnetic radiator is quite simple and interesting. Any electromagnetic system with a discontinuity is radiating electromagnetic energy. The size, shape and orientation of the discontinuities control the radiation characteristics of the system such as radiation pattern, gain, polarization etc. It can be either resonant or non-resonant. This thesis deals with antennas that are developed from a class of transmission lines known as coplanar strip-CPS, a planar analogy of parallel pair transmission line. The specialty of CPS is its symmetric structure compared to other transmission lines, which makes the antenna structures developed from CPS quite simple for design and fabrication. The structural modifications on either metallic strip of CPS results in different antennas. The first part of the thesis discusses a single band and dual band design derived from open ended slot lines which are very much suitable for 2.4 and 5.2 GHz WLAN applications. The second section of the study is vectored into the development of enhanced gain dipoles. A single band dipole and a wide band enhanced gain dipole suitable for 5.2/5.8 GHZ band and imaging applications are developed and discussed. Last part of the thesis discusses the development of directional UWBs. Three different types of ultra-compact UWBs are developed and almost all the frequency domain and time domain analysis of the structures are discussed.

Texture segmentation in Williams syndrome

Williams syndrome (WS) is a developmental disorder in which visuo-spatial cognition is poor relative to verbal ability. At the level of visuo-spatial perception, individuals with WS can perceive both the local and global aspects of an image. However, the manner in which local elements are integrated into a global whole is atypical, with relative strengths in integration by luminance, closure, and alignment compared to shape, orientation and proximity. The present study investigated the manner in which global images are segmented into local parts. Segmentation by seven gestalt principles was investigated: proximity, shape, luminance, orientation, closure, size (and alignment: Experiment I only). Participants were presented with uniform texture squares and asked to detect the presence of a discrepant patch (Experiment 1) or to identify the form of a discrepant patch as a capital E or H (Experiment 2). In Experiment 1, the pattern and level of performance of the WS group did not differ from that of typically developing controls, and was commensurate with the general level of non-verbal ability observed in WS. These results were replicated in Experiment 2, with the exception of segmentation by proximity, where individuals with WS demonstrated superior performance relative to the remaining segmentation types. Overall, the results suggest that, despite some atypical aspects of visuo-spatial perception in WS, the ability to segment a global form into parts is broadly typical in this population. In turn, this informs predictions of brain function in WS, particularly areas V1 and V4. (c) 2006 Elsevier Ltd. All rights reserved.

Using an additive to control the electrospinning of fibres of poly(epsilon-caprolactone)

Electrospinning is a route to polymer fibres with diameters considerably smaller than available from most fibre-producing techniques. We explore the use of a low molecular weight compound as an effective control additive during the electrospinning of poly(epsilon-caprolactone). This approach extends the control variables for the electrospinning of nanoscale fibres from the more usual ones such as the polymer molecular weight, solvent and concentration. We show that through the use of dual solvent systems, we can alter the impact of the additive on the electrospinning process so that finer as well as thicker fibres can be prepared under otherwise identical conditions. As well as the size of the fibres and the number of beads, the use of the additive allows us to alter the level of crystallinity as well as the level of preferred orientation of the poly(epsilon-caprolactone) crystals. This approach, involving the use of a dual solvent and a low molar mass compound, offers considerable potential for application to other polymer systems. (C) 2010 Society of Chemical Industry

Origin of the Parry arc

Laboratory experiments to determine the preferred orientation of free-falling hexagonal prisms were performed at Reynolds numbers appropriate to falling ice crystals in the atmosphere. Hexagonal plates orient with their c axis vertical for aspect ratios < 0.9, whilst hexagonal columns fall with their c axis horizontal. A secondary alignment is also observed: regular hexagonal columns fall preferentially with two prism facets aligned vertically and not horizontally – the latter scenario was previously assumed to be responsible for the rare Parry arc. However, if the column is made scalene in its cross-section, it can orient such that a pair of prism facets is horizontal. This finding indicates that the development of scalene crystals may be key to the production of certain ice-crystal optical phenomena

Memory effects in liquid crystal elastomers

Free-standing monodomain liquid crystal elastomer samples are shown to have a complete memory of the orientational configuration at the time of cross-linking. This memory is demonstrated through samples in which the parent polymer system is first aligned in a magnetic field prior to cross-linking. These films show reversible nematic-isotropic phase transitions and x-ray scattering patterns characteristic of nematic phases. The liquid crystal elastomer films exhibit a remarkable memory effect, in that the sample may be held at temperatures well above the nematic-isotropic transition for extended periods ( > 2 weeks), but on cooling into the liquid crystal phase region, both the original director alignment and the degree of preferred orientation are recovered. It is demonstrated that these novel memory effects are equilibrium in nature. The origins of this phenomena in terms of coupling between the mesogenic side-chains and the polymer network are discussed.