Thermal studies of D.C. traction motors

This paper describes a thorough thermal study on a fleet of DC traction motors which were found to suffer from overheating after 3 years of full operation. Overheating of these traction motors is attributed partly because of the higher than expected number of starts and stops between train terminals. Another probable cause of overheating is the design of the traction motor and/or its control strategy. According to the motor manufacturer, a current shunt is permanently connected across the motor field winding. Hence, some of the armature current is bypassed into the current shunt. The motor then runs above its rated speed in the field weakening mode. In this study, a finite difference model has been developed to simulate the temperature profile at different parts inside the traction motor. In order to validate the simulation result, an empty vehicle loaded with drums of water was also used to simulate the full pay-load of a light rail vehicle experimentally. The authors report that the simulation results agree reasonably well with experimental data, and it is likely that the armature of the traction motor will run cooler if its field shunt is disconnected at low speeds

Do Chinese traditional values matter in regulating China’s company directors? Preliminary findings from surveys in Hong Kong

This article argues that Chinese traditional values do matter in Chinese corporate governance. The object is to report on the preliminary findings of a project supported by the General Research Fund in Hong Kong (HK). Thus far the survey results from HK respondents support the authors’ hypothesis. As such, traditional Chinese values should be on the agenda of the next round of company law reforms in China

The first global entertainment company : explaining Pathe's dominance in the pre-Hollywood film industry

For almost a decade before Hollywood existed, French firm Pathe towered over the early film industry with estimates of its share of all films sold around the world varying between 50-70%. Pathe was the first global entertainment company. This paper analyses its rise to market leadership by applying a theoretical framework drawn from the business literature on causes of industry dominance, which provides insights into how firms acquire and maintain market dominance and in this case the film industry. This paper uses evidence presented by film historians to argue that Pathe "fits" the expected theoretical model of a dominant firm because it had a marketing orientation, used an effective quality-based competitive strategy and possessed the six critical marketing capabilities that business research shows enable the best performing firms to consistently outperform rivals.

Board network characteristics and company performance in Sweden : the case of Gnosjö companies and their board members in southern Sweden

When managers of entrepreneurial companies typically talk about strategies, they first consider what products to make and secondly where to locate the business. The entrepreneurial companies locate in rural areas because of a wish to maintain a certain lifestyle, or because they can combine a resource available there with certain knowledge or interest that they have (Getz and Nilsson, 2004). In addition, many managers of entrepreneurial companies are confident in locating in a rural area, because there often is economic and social structure supportive of local corporate governance. The most central part of corporate governance is the board of directors. In an entrepreneurial company in a rural area, such members of boards are most likely to be individuals in dominant positions influential in the local economy.

Small, Medium, Large: Theatre Companies and Issues of Scale - A Case Study of a Medium-Sized Company

'Surviving but not thriving.' Tbat is the message about small to mediumsized companies that Ian McRae, Chair ofthe Theatre Board of the Australia Council, has been delivering since 2003. In the Theatre Board Assessment Meeting Report of 2007, McRae strongly urged renewed financial support for this most important sector given the significant decrease over the last 10 years and the consequent decrease in new Australian works being produced. Without such support his prediction is that'considerable damage could be done to the creative infrastructure across Australia resulting in a loss of artistic vibrancy down the track that could be very difficult to recover' (McRae, 2007:3).

The treatment of employee priority in a deed of company arrangement

This article examines one of the changes implemented in the Corporations Amendment (Insolvency) Act 2007 (Cth) . It is argued that the insertion of s 444DA raises some matters that go to the nature of the insolvency process generally and the operation of Pt 5.3A in a particular. The position of employees in insolvency is a matter that is the subject of much comment from a policy perspective. This article does not cover that debate but provides some initial explanation of the need to protect employees. The second part of the article covers the particular background to the voluntary administration system as far as employee rights are concerned as well as the arguments put forward by the government to justify the change in the legislation which inserted s 444DA . It suggests that there was little evidence provided for the need to protect employee priority rights in this particular way. An alternative explanation is given for the change adopted by the government. The third part of the article suggests that the manner in which the legislation seeks to better protect employee creditors is somewhat clumsy in its operation. It raises a number of questions about how the legislation may operate and argues that given the stated aims, some alteration to it would improve its effectiveness.

The first global entertainment company : explaining Pathe's global dominance in the pre-Hollywood film industry

For almost a decade before Hollywood existed, French firm Pathe towered over the early film industry with estimates of its share of all films sold around the world varying between 50-70%. Pathe was the first global entertainment company. This paper analyses its rise to market leadership by applying a theoretical framework drawn from the business literature on causes of industry dominance, which provides insights into how firms acquire and maintain market dominance, and in this case the film industry. This paper uses evidence presented by film historians to argue that Pathe “fits” the expected theoretical model of a dominant firm because it had a marketing orientation, used an effective quality-based competitive strategy and possessed the six critical strategic marketing capabilities that business research shows enable the best performing firms to consistently outperform rivals

For blood, sweat and tears : the severing of subconscious connections with company and business model

Humans have altered environments and enhanced their well being unlike any other creature on the planet (Heilman & Donna, 2007); this is no different whether the environment is ecological, social or organisational. In recent times business modelling techniques have become intricately detailed in the pre-designing and evaluating of business flow before the final implementation (Ou-Yang & Lin, 2008). The importance of the organisation change and business process model is undeniable. The feedback received from real business process users is that the notation is easy to learn; the models do help people to understand the process better; the models can be used to improve the (business) process; and the notation is expressive enough to capture the essential information (Bennett, Doshi, Do Vale Junior, Kumar, Manikam, & Madavan, 2009).

Load modelling : induction motors

Modelling the power systems load is a challenge since the load level and composition varies with time. An accurate load model is important because there is a substantial component of load dynamics in the frequency range relevant to system stability. The composition of loads need to be charaterised because the time constants of composite loads affect the damping contributions of the loads to power system oscillations, and their effects vary with the time of the day, depending on the mix of motors loads. This chapter has two main objectives: 1) describe the load modelling in small signal using on-line measurements; and 2) present a new approach to develop models that reflect the load response to large disturbances. Small signal load characterisation based on on-line measurements allows predicting the composition of load with improved accuracy compared with post-mortem or classical load models. Rather than a generic dynamic model for small signal modelling of the load, an explicit induction motor is used so the performance for larger disturbances can be more reliably inferred. The relation between power and frequency/voltage can be explicitly formulated and the contribution of induction motors extracted. One of the main features of this work is the induction motor component can be associated to nominal powers or equivalent motors

Problem-solving courts, therapeutic jurisprudence and the constitution : if two is company, is three a crowd?

Court costs, resource-intensive trials, booming prison populations and the obduracy of recidivism rates all present as ugly excesses of the criminal law adversarial paradigm. To combat these excesses, problem-solving courts have evolved with an edict to address the underlying issues that have caused an individual to commit a crime. When a judge seeks to help a problem-solving court participant deal with issues like addiction, mental health or poverty, they are performing a very different role to that of a judicial officer in the traditional court hierarchy. They are no longer the removed, independent arbiter — a problem-solving court judge steps into the ‘arena’ with the participant and makes active use of their judicial authority to assist in rehabilitation and positive behavioural change. Problem-solving court judges employing the principles of therapeutic jurisprudence appreciate that their interaction with participants can have therapeutic and anti-therapeutic consequences. This article will consider how the deployment of therapeutic measures (albeit with good intention) can lead to the behavioural manifestation of partiality and bias on the part of problem-solving court judges. Chapter III of the Commonwealth Constitution will then be analysed to highlight why the operation and functioning of problem solving courts may be deemed unconstitutional. Part IV of this article will explain how a problem-solving court judge who is not acting impartially or independently will potentially contravene the requirements of the Constitution. It will finally be suggested that judges who possess a high level of emotional intelligence will be the most successful in administering an independent and impartial problem solving court.

Assembly line balancing the comparison of COMSOAL and MSNSH technique in Motorcycle manufacturing company

Today’s highly competitive market influences the manufacturing industry to improve their production systems to become the optimal system in the shortest cycle time as possible. One of most common problems in manufacturing systems is the assembly line balancing problem. The assembly line balancing problem involves task assignments to workstations with optimum line efficiency. The line balancing technique, namely “COMSOAL”, is an abbreviation of “Computer Method for Sequencing Operations for Assembly Lines”. Arcus initially developed the COMSOAL technique in 1966 [1], and it has been mainly applied to solve assembly line balancing problems [6]. The most common purposes of COMSOAL are to minimise idle time, optimise production line efficiency, and minimise the number of workstations. Therefore, this project will implement COMSOAL to balance an assembly line in the motorcycle industry. The new solution by COMSOAL will be used to compare with the previous solution that was developed by Multi‐Started Neighborhood Search Heuristic (MSNSH), which will result in five aspects including cycle time, total idle time, line efficiency, average daily productivity rate, and the workload balance. The journal name “Optimising and simulating the assembly line balancing problem in a motorcycle manufacturing company: a case study” will be used as the case study for this project [5].

A case-control study of ambient heat exposure and urolithiasis among outdoor workers in a shipbuilding company, Guangzhou, China

Higher ambient temperatures will increase heat stress on workers, leading to impacts upon their individual health and productivity. In particular, research has indicated that higher ambient temperatures can increase the prevalence of urolithiasis. This thesis examines the relationship between ambient heat exposure and urolithiasis among outdoor workers in a shipbuilding company in Guangzhou, China, and makes recommendations for minimising the possible impacts of high ambient temperatures on urolithiasis. A retrospective 1:4 matched case-control study was performed to investigate the association between ambient heat exposure and urolithiasis. Ambient heat exposure was characterised by total exposure time, type of work, department and length of service. The data were obtained from the affiliated hospital of the shipbuilding company under study for the period 2003 to 2010. A conditional logistic regression model was used to estimate the association between heat exposure and urolithiasis. This study found that the odds ratio (OR) of urolithiasis for total exposure time was 1.5 (95% confidence interval (CI): 1.2–1.8). Eight types of work in the shipbuilding company were investigated, including welder, assembler, production security and quality inspector, planing machine operator, spray painter, gas-cutting worker and indoor employee. Five out of eight types of work had significantly higher risks for urolithiasis, and four of the five mainly consisted of outdoors work with ORs of 4.4 (95% CI: 1.7–11.4) for spray painter, 3.8 (95% CI: 1.9–7.2) for welder, 2.7 (95% CI: 1.4–5.0) for production security and quality inspector, and 2.2 (95% CI: 1.1–4.3) for assembler, compared to the reference group (indoor employee). Workers with abnormal blood pressure (hypertension) were more likely to have urolithiasis with an OR of 1.6 (95% CI: 1.0–2.5) compared to those without hypertension. This study contributes to the understanding of the association between ambient heat exposure and urolithiasis among outdoor workers in China. In the context of global climate change, this is particularly important because rising temperatures are expected to increase the prevalence of urolithiasis among outdoor workers, putting greater pressure on productivity, occupational health management and health care systems. The results of this study have clear implications for public health policy and planning, as they indicate that more attention is required to protect outdoor workers from heat-related urolithiasis.