Effect of power line filter on MOV clamping voltage

Metal oxide varistors (MOV) are popularly used to protect offline electronic equipment against power line transients. The offline switched mode power supplies (SMPS) use power line filters and MOVs in the front-end. The power line filter is used to reduce the conducted noise emission into the power line and the MOVs connected before this line filter and the MOVs connected before this line filter to clamp line transients to safer levels thereby protecting the SMPS. Because of the presence of 'X' capacitors at the input of line filter the MOV clamping voltage is increased. This paper presents one such case and gives theoretical and experimental results. An approximate method to predetermine the magnitude of such clamping voltages is also presented.

Investigation of the dilution process for measurement of particulate matter from spark-ignition engines

Measurements of particulate matter (PM) from spark ignition (SI) engine exhaust using dilution tunnels will become more prevalent as emission standards are tightened. Hence, a study of the dilution process was undertaken in order to understand how various dilution related parameters affect the accuracy with which PM sizes and concentrations can be determined. A SI and a compression ignition (CI) engine were separately used to examine parameters of the dilution process; the present work discusses the results in the context of SI exhaust dilution. A Scanning Mobility Particle Sizer (SMPS) was used to measure the size distribution, number density, and volume fraction of PM. Temperature measurements in the exhaust pipe and dilution tunnel reveal the degree of mixing between exhaust and dilution air, the effect of flowrate on heat transfer from undiluted and diluted exhaust to the environment, and the minimum permissible dilution ratio for a maximum sample temperature of 52°C. Measurements of PM concentrations as a function of dilution ratio show the competing effects of temperature and particle/vapor concentrations on particle growth dynamics, which result in a range of dilution ratios-from 13 to 18-where the effect of dilution ratio, independent of flowrate, is kept to a minimum. This range of dilution ratios is therefore optimal in order to achieve repeatable PM concentration measurements. Particle dynamics during transit through the tunnel operating at the optimal dilution ratio was found statistically insignificant compared to data scatter. Such small differences in number concentration may be qualitatively representative of particle losses for SI exhaust, but small increases in PM volume fraction during transit through the tunnel may significantly underestimate accretion of mass due to unburned hydrocarbons (HCs) emitted by SI engines. The fraction of SI-derived PM mass due to adsorbed/absorbed vapor, estimated from these data, is consistent with previous chemical analyses of PM. © 1998 Society of Automotive Engineers, Inc.

An investigation into the tropospheric chemistry of acidic aerosols and ammonia in the laboratory

This thesis describes a broad range of experiments based on an aerosol flow-tube system to probe the interactions between atmospherically relevant aerosols with trace gases. This apparatus was used to obtain simultaneous optical and size distribution measurements using FTIR and SMPS measurements respectively as a function of relative humidity and aerosol chemical composition. Heterogeneous reactions between various ratios of ammonia gas and acidic aerosols were studied in aerosol form as opposed to bulk solutions. The apparatus is unique, in that it employed two aerosol generation methods to follow the size evolution of the aerosol while allowing detailed spectroscopic investigation of its chemical content. A novel chemiluminescence apparatus was also used to measure [NH4+]. SO2.H2O is an important species as it represents the first intermediate in the overall atmospheric oxidation process of sulfur dioxide to sulfuric acid. This complex was produced within gaseous, aqueous and aerosol SO2 systems. The addition of ammonia, gave mainly hydrogen sulfite tautomers and disulfite ions. These species were prevalent at high humidities enhancing the aqueous nature of sulfur (IV) species. Their weak acidity is evident due to the low [NH4+] produced. An increasing recognition that dicarboxylic acids may contribute significantly to the total acid burden in polluted urban environments is evident in the literature. It was observed that speciation within the oxalic, malonic and succinic systems shifted towards the most ionised form as the relative humidity was increased due to complete protonisation. The addition of ammonia produced ammonium dicarboxylate ions. Less reaction for ammonia with the malonic and succinic species were observed in comparison to the oxalic acid system. This observation coincides with the decrease in acidity of these organic species. The interaction between dicarboxylic acids and ‘sulfurous’/sulfuric acid has not been previously investigated. Therefore the results presented here are original to the field of tropospheric chemistry. SHO3-; S2O52-; HSO4-; SO42- and H1,3,5C2,3,4O4-;C2,3,4O4 2- were the main components found in the complex inorganic-organic systems investigated here. The introduction of ammonia produced ammonium dicarboxylate as well as ammonium disulfite/sulfate ions and increasing the acid concentrations increased the total amount of [NH4+].

A auditoria das Pequenas e Médias Empresas em Portugal: presente e futuro

Dissertação de Mestrado apresentado ao Instituto Superior de Contabilidade e Administração do Porto para a obtenção do grau de Mestre em Auditoria sob orientação de Adalmiro Álvaro Malheiro de Castro Andrade Pereira

Mass and size distribution measurement of particulates from a gas turbine combustor using modern mobility analyzer and particle sizer

SMPS and DMS500 analysers were used to measure particulate size distributions in the exhaust of a fully annular aero gas turbine engine at two operating conditions to compare and analyse sources of discrepancy. A number of different dilution ratio values were utilised for the comparative analysis, and a Dekati hot diluter operating at a temperature of 623°K was also utilised to remove volatile PM prior to measurements being made. Additional work focused on observing the effect of varying the sample line temperatures to ascertain the impact. Explanations are offered for most of the trends observed, although a new, repeatable event identified in the range from 417°K to 423°K – where there was a three order of magnitude increase in the nucleation mode of the sample – requires further study.

An improved reliability Cuk based solar inverter with sliding mode control

Many photovoltaic inverter designs make use of a buck based switched mode power supply (SMPS) to produce a rectified sinusoidal waveform. This waveform is then unfolded by a low frequency switching structure to produce a fully sinusoidal waveform. The Cuk SMPS could offer advantages over the buck in such applications. Unfortunately the Cuk converter is considered to be difficult to control using classical methods. Correct closed loop design is essential for stable operation of Cuk converters. Due to these stability issues, Cuk converter based designs often require stiff low bandwidth control loops. In order to achieve this stable closed loop performance, traditional designs invariably need large, unreliable electrolytic capacitors. In this paper, an inverter with a sliding mode control approach is presented which enables the designer to make use of the Cuk converters advantages, while ameliorating control difficulties. This control method allows the selection of passive components based predominantly on ripple and reliability specifications while requiring only one state reference signal. This allows much smaller, more reliable non-electrolytic capacitors to be used. A prototype inverter has been constructed and results obtained which demonstrate the design flexibility of the Cuk topology when coupled with sliding mode control.

Desempenho de um painel fotovoltaico de baixa tensão, acoplado ao protótipo de um conversor dc/dc topologia Booster

Low voltage solar panels increase the reliability of solar panels due to reduction of in series associations the configurations of photovoltaic cells. The low voltage generation requires DCDC converters devices with high efficiency, enabling raise and regulate the output voltage. This study analyzes the performance of a photovoltaic panel of Solarex, MSX model 77, configured to generate an open circuit voltage of 10.5 V, with load voltage of 8.5 V, with short circuit current of 9 A and a power of 77 W. The solar panel was assembled in the isolated photovoltaic system configuration, with and without energy storage as an interface with a DCDC converter, Booster topology. The converter was designed and fabricated using SMD (Surface Mounted Devices) technology IC (integrated circuit) that regulates its output voltage at 14.2 V, with an efficiency of 87% and providing the load a maximum power of 20.88 W. The system was installed and instrumented for measurement and acquisition of the following data: luminosities, average global radiation (data of INPE Instituto Nacional de Pesquisas Espaciais), solar panel and environment temperatures, solar panel and DC-DC converter output voltages, panel, inverter, and battery charge output currents. The photovoltaic system was initially tested in the laboratory (simulating its functioning in ideal conditions of operation) and then subjected to testing in real field conditions. The panel inclination angle was set at 5.5°, consistent with the latitude of Natal city. Factors such as climatic conditions (simultaneous variations of temperature, solar luminosities and ra diation on the panel), values of load resistance, lower limit of the maximum power required by the load (20.88 W) were predominant factors that panel does not operate with energy efficiency levels greater than 5 to 6%. The average converter efficiency designed in the field test reached 95%

A novel strategy for building interoperable MPI environment in heterogeneous high performance systems

Breakthrough advances in microprocessor technology and efficient power management have altered the course of development of processors with the emergence of multi-core processor technology, in order to bring higher level of processing. The utilization of many-core technology has boosted computing power provided by cluster of workstations or SMPs, providing large computational power at an affordable cost using solely commodity components. Different implementations of message-passing libraries and system softwares (including Operating Systems) are installed in such cluster and multi-cluster computing systems. In order to guarantee correct execution of message-passing parallel applications in a computing environment other than that originally the parallel application was developed, review of the application code is needed. In this paper, a hybrid communication interfacing strategy is proposed, to execute a parallel application in a group of computing nodes belonging to different clusters or multi-clusters (computing systems may be running different operating systems and MPI implementations), interconnected with public or private IP addresses, and responding interchangeably to user execution requests. Experimental results demonstrate the feasibility of this proposed strategy and its effectiveness, through the execution of benchmarking parallel applications.

Sistema nervoso enterico e scrapie sperimentale in ovini di razza sarda con diversa suscettibilità genetica nei confronti della malattia

Sebbene il sistema nervoso enterico (“enteric nervous system”, ENS) svolga un ruolo cruciale nella patogenesi della Scrapie ovina, non esistono tuttavia in letteratura dati sulle popolazioni cellulari progressivamente coinvolte nel corso dell’infezione, né sugli eventuali danni morfo-funzionali da esse subiti. Il presente studio è stato condotto sui plessi mienterici e sottomucosi dell’ileo di 46 pecore di razza Sarda, recanti diversi polimorfismi del gene Prnp (ARQ/ARQ, ARQ/AHQ, ARQ/ARR, ARR/ARR). I suddetti animali, infettati per os all’età di 8 mesi con un ceppo di Scrapie precedentemente caratterizzato nel topo, sono stati sacrificati mediante eutanasia a determinati intervalli di tempo post-infezione (p.i.). E’ stata quindi valutata, tramite immunoistochimica ed immunofluorescenza indiretta su sezioni tissutali e su preparati “wholemount”, l’immunoreattività (IR) nei confronti della PrPSc, del “marker” panneuronale Hu C/D, dell’ossido-nitrico sintetasi (nNOS), della calbindina (CALB) e della proteina fibrillare acida gliale (GFAP). In 8 pecore con genotipo ARQ/ARQ, clinicamente sane e sacrificate a 12-24 mesi p.i., nonché in 5 ovini clinicamente affetti (2 con genotipo ARQ/ARQ, 3 con genotipo ARQ/AHQ), questi ultimi sacrificati rispettivamente a 24, 36 e 40 mesi p.i., le indagini immunoistochimiche hanno consentito di dimostrare la presenza di PrPSc a livello sia dell’encefalo (obex), sia dell’ENS, in particolar modo nei plessi mienterici. In tali distretti il deposito della PrPSc risultava pienamente compatibile con un interessamento delle cellule enterogliali (“enteroglial cells”, EGCs), mentre occasionalmente si notava un contestuale coinvolgimento della componente neuronale ivi residente. In conclusione, i dati della presente indagine consentono di ipotizzare un verosimile coinvolgimento delle EGCs e dei neuroni residenti a livello dei plessi dell’ENS nella patogenesi della Scrapie sperimentale realizzata per os in ovini di razza Sarda.

Bestimmung der Größenverteilung von sekundären organischen Aerosolen aus der Photooxidation biogener Terpene

Diese Arbeit untersucht die Bildung vonsekundärem organischem Aerosol aus der Gasphasenoxidation vonbiogenen Terpenen. Dazu wurde die Größenverteilung desentstandenen Aerosols kontinuierlich über die Bestimmung derelektrischen Beweglichkeit der einzelnen Teilchen gemessen (SMPS,TSI 3936). In diesem Zusammenhang wurde im ersten Teil dasNukleationspotential der unterschiedlichen Oxidationstypen vona-Pinen und b-Pinen durch O_3, OH und NO_3 über die Messung dergebildeten Partikelanzahl- und Volumenkonzentrationen verglichen.Es zeigte sich, dass sowohl die Reaktion desendozyklischen a-Pinen als auch die desexozyklischen b-Pinen mit Ozon zu einer ca. hundertfachhöheren maximalen Partikelanzahlkonzentration führte als dieReaktionen mit OH bzw. NO_3. Hinsichtlich des Beitrages zurVolumenbildung dominierte bei endozyklischenMonoterpen-Reaktionen die Ozonolyse, während die Beiträge allerdrei exozyklische b-Pinen-Reaktionen in der selbenGrößenordnung lagen: der höchste Wert wurde für dieOH-Reaktion gemessen, gefolgt von der NO_3-Reaktion und derOzonolyse als Minimum. Im zweiten Teil der Arbeit wurdenUntersuchungen zum Wasserdampfeinfluss auf die beobachteteGrößenverteilung und damit auf die Aerosolbildung durchgeführt.Sie ließen einzig bei der Ozonolyse einen Effekt - Reduktion derNukleation - erkennen, der sich auf exozyklischeReaktionen stärker auswirkte, als auf endozyklische.Diese Ergebnisse wurden im Anschluss dazu genutzt, indirektRückschlüsse auf die, die Partikelbildung verursachendenSubstanzen zu ziehen, deren direkter Zugang über die chemischeAnalyse aufgrund der geringen Masse der nukleierten Teilchenderzeit nicht möglich ist. Hierbei wurden dieintermolekular gebildeten sekundären Ozonide für dieReaktion von exozyklischen Monoterpenen und dieintramolekular gebildeten sekundären Ozonide für dieendozyklischen Monoterpen Reaktionen mit Ozon alsNukleationsvorläufer ausgemacht.Mit einer parallel dazu aufgebauten getrennten Sammlung von Gas-und Aerosolprodukten konnte durch ionenchromatographische Analyseein ähnliches Verhalten für die Dicarbons'auren ausgeschlossenwerden, die bislang als Nukleationsvorläufer während derOzon-Reaktion von Terpenen angesehen wurden.Im abschließendenTeil der Arbeit wurden Experimente mit Sesquiterpenen bei nahezuatmosphärischen Bedingungen durchgeführt, die ein ähnlichesVerhalten bezüglich der Wasserdampfkonzentration zeigten. Sielassen eine hohe atmosphärische Relevanz der Nukleationverursacht durch Sesquiterpen-Ozon-Reaktionen vermuten.

Development of analytical methodologies for iodine species in gaseous and particulate phases of the coastal atmosphere

It has been demonstrated that iodine does have an important influence on atmospheric chemistry, especially the formation of new particles and the enrichment of iodine in marine aerosols. It was pointed out that the most probable chemical species involved in the production or growth of these particles are iodine oxides, produced photochemically from biogenic halocarbon emissions and/or iodine emission from the sea surface. However, the iodine chemistry from gaseous to particulate phase in the coastal atmosphere and the chemical nature of the condensing iodine species are still not understood. A Tenax / Carbotrap adsorption sampling technique and a thermo-desorption / cryo-trap / GC-MS system has been further developed and improved for the volatile organic iodine species in the gas phase. Several iodo-hydrocarbons such as CH3I, C2H5I, CH2ICl, CH2IBr and CH2I2 etc., have been measured in samples from a calibration test gas source (standards), real air samples and samples from seaweeds / macro-algae emission experiments. A denuder sampling technique has been developed to characterise potential precursor compounds of coastal particle formation processes, such as molecular iodine in the gas phase. Starch, TMAH (TetraMethylAmmonium Hydroxide) and TBAH (TetraButylAmmonium Hydroxide) coated denuders were tested for their efficiencies to collect I2 at the inner surface, followed by a TMAH extraction and ICP/MS determination, adding tellurium as an internal standard. The developed method has been proved to be an effective, accurate and suitable process for I2 measurement in the field, with the estimated detection limit of ~0.10 ng∙L-1 for a sampling volume of 15 L. An H2O/TMAH-Extraction-ICP/MS method has been developed for the accurate and sensitive determination of iodine species in tropospheric aerosol particles. The particle samples were collected on cellulose-nitrate filters using conventional filter holders or on cellulose nitrate/tedlar-foils using a 5-stage Berner impactor for size-segregated particle analysis. The water soluble species as IO3- and I- were separated by anion exchanging process after water extraction. Non-water soluble species including iodine oxide and organic iodine were digested and extracted by TMAH. Afterwards the triple samples were analysed by ICP/MS. The detection limit for particulate iodine was determined to be 0.10~0.20 ng•m-3 for sampling volumes of 40~100 m3. The developed methods have been used in two field measurements in May 2002 and September 2003, at and around the Mace Head Atmospheric Research Station (MHARS) located at the west coast of Ireland. Elemental iodine as a precursor of the iodine chemistry in the coastal atmosphere, was determined in the gas phase at a seaweed hot-spot around the MHARS, showing I2 concentrations were in the range of 0~1.6 ng∙L-1 and indicating a positive correlation with the ozone concentration. A seaweed-chamber experiment performed at the field measurement station showed that the I2 emission rate from macro-algae was in the range of 0.019~0.022 ng•min-1•kg-1. During these experiments, nanometer-particle concentrations were obtained from the Scanning Mobility Particle Sizer (SMPS) measurements. Particle number concentrations were found to have a linear correlation with elemental iodine in the gas phase of the seaweeds chamber, showing that gaseous I2 is one of the important precursors of the new particle formation in the coastal atmosphere. Iodine contents in the particle phase were measured in both field campaigns at and around the field measurement station. Total iodine concentrations were found to be in the range of 1.0 ~ 21.0 ng∙m-3 in the PM2.5 samples. A significant correlation between the total iodine concentrations and the nanometer-particle number concentrations was observed. The particulate iodine species analysis indicated that iodide contents are usually higher than those of iodate in all samples, with ratios in the range of 2~5:1. It is possible that those water soluble iodine species are transferred through the sea-air interface into the particle phase. The ratio of water soluble (iodate + iodide) and non-water soluble species (probably iodine oxide and organic iodine compounds) was observed to be in the range of 1:1 to 1:2. It appears that higher concentrated non-water soluble species, as the products of the photolysis from the gas phase into the particle phase, can be obtained in those samples while the nucleation events occur. That supports the idea that iodine chemistry in the coastal boundary layer is linked with new particle formation events. Furthermore, artificial aerosol particles were formed from gaseous iodine sources (e.g. CH2I2) using a laboratory reaction-chamber experiment, in which the reaction constant of the CH2I2 photolysis was calculated to be based upon the first order reaction kinetic. The end products of iodine chemistry in the particle phase were identified and quantified.

Studio della formazione di espansi poliuretanici ad elevata resilienza contenenti reticolanti silanici

La produzione di sedili auto rappresenta una delle principali applicazioni delle schiume poliuretaniche flessibili a bassa densità. La forte necessità di riduzione del peso totale del veicolo si traduce in una richiesta di significative riduzioni di densità dei materiali utilizzati per l’interno vettura. Tale riduzione deve tuttavia essere associata a migliorate proprietà, nel senso del mantenimento delle performance nel tempo, della sicurezza e del comfort. Ricerche di mercato hanno evidenziato la necessità di sviluppare schiume poliuretaniche con elevate performance in termini di comfort, associate a significative riduzioni di densità e significative riduzioni di spessori applicati, nell’ottica di produrre sedili sempre più sottili consentendo la massima flessibilità di design dell’interno del veicolo. Scopo del presente progetto è lo sviluppo di una nuova chimica associata a quella del poliuretano che permetta di ottenere un elevato comfort. Il corpo umano e maggiormente sensibile a vibrazioni con frequenza tra i 4 e gli 8 Hz. In questo intervallo di frequenze le vibrazioni trasmesse sono correlate con l’isteresi del materiale stesso. Solitamente basse isteresi sono associate a bassa trasmissività delle vibrazioni. I produttori di auto hanno quindi cominciato a valutare il comfort di un sedile in termini di isteresi del materiale stesso. Nel caso specifico è considerato un sedile confortevole se possiede una isteresi inferiore al 18%. Le performance in termini di comfort devono essere associate anche ad una bassa emissione di composti organici volatili, con particolare attenzione ad ammine e aldeidi, ad un 15% di riduzione di densità (l’obiettivo è raggiungere una densità di 60 g/L a fronte di una densità attuale che si colloca nel range 75-80 g/L), con proprietà fisico meccaniche e resistenza all’invecchiamento in grado di soddisfare i capitolati delle case automobilistiche. Recentemente la produzione di SMPs (silane-modified polymers) ricopre un ruolo fondamentale nel mercato dei sigillanti e degli adesivi. L’idea di utilizzare questa famiglia di silani nella produzione di schiume poliuretaniche flessibili risiede nel fatto che, esattamente come in sigillanti e adesivi, ci possa essere una reazione successiva a quella di formazione del PU che possa dare ulteriore reticolazione della frazione morbida. La reazione di post-curing del silano ha incontrato diverse problematiche relative alla scarsa reattività del silano stesso. Per attivare la reazione di idrolisi e oligomerizzazione si è utilizzato un acido di Brønsted (DBSA) ma l’interazione con le ammine presenti nel poliolo formulato, necessarie alla reazione di formazione del legame uretanico, ne hanno inibito l’attività.

Synthese und Evaluierung makrozyklischer 68 Ga-MPI-Tracer auf Pyridaben-Basis

Herz-Kreislauf-Erkrankungen zählen weltweit zu den Hauptursachen, die zu frühzeitigem Tod führen. Pathophysiologisch liegt eine Gefäßwandverdickung durch Ablagerung arteriosklerotischer Plaques (Arteriosklerose) vor. Die molekulare Bildgebung mit den nuklearmedizinischen Verfahren SPECT und PET zielt darauf ab, minderperfundierte Myokardareale zu visualisieren, um den Krankheitsverlauf durch frühzeitige Therapie abschwächen zu können. Routinemäßig eingesetzt werden die SPECT-Perfusionstracer [99mTc]Sestamibi und [99mTc]Tetrofosmin. Zum Goldstandard für die Quantifizierung der Myokardperfusion werden allerdings die PET-Tracer [13N]NH3 und [15O]H2O, da eine absolute Bestimmung des Blutflusses in mL/min/g sowohl in der Ruhe als auch bei Belastung möglich ist. 2007 wurde [18F]Flurpiridaz als neuer Myokardtracer vorgestellt, dessen Bindung an den MC I sowohl in Ratten, Hasen, Primaten als auch in ersten klinischen Humanstudien eine selektive Myokardaufnahme zeigte. Um eine Verfügbarkeit des Radionuklids über einen Radionuklidgenerator gewährleisten zu können, sollten makrozyklische 68Ga-Myokard-Perfusionstracer auf Pyridaben-Basis synthetisiert und evaluiert werden. Die neue Tracer-Klasse setzte sich aus dem makrozyklischen Chelator, einem Linker und dem Insektizid Pyridaben als Targeting-Vektor zusammen. Struktur-Affinitätsbeziehungen konnten auf Grund von Variation des Linkers (Länge und Polarität), der Komplexladung (neutral und einfach positiv geladen), des Chelators (DOTA, NODAGA, DO2A) sowie durch einen Multivalenzansatz (Monomer und Dimer) aufgestellt werden. Insgesamt wurden 16 neue Verbindungen synthetisiert. Ihre 68Ga-Markierung wurde hinsichtlich pH-Wert, Temperatur, Vorläufermenge und Reaktionszeit optimiert. Die DOTA/NODAGA-Pyridaben-Derivate ließen sich mit niedrigen Substanzmengen (6 - 25 nmol) in 0,1 M HEPES-Puffer (pH 3,4) bei 95°C innerhalb 15 min mit Ausbeuten > 95 % markieren. Für die DO2A-basierenden Verbindungen bedurfte es einer mikrowellengestützen Markierung (300 W, 1 min, 150°C), um vergleichbare Ausbeuten zu erzielen. Die in vitro-Stabilitätstests aller Verbindungen erfolgten in EtOH, NaCl und humanem Serum. Es konnten keine Instabilitäten innerhalb 80 min bei 37°C festgestellt werden. Unter Verwendung der „shake flask“-Methode wurden die Lipophilien (log D = -1,90 – 1,91) anhand des Verteilungs-quotienten in Octanol/PBS-Puffer ermittelt. Die kalten Referenzsubstanzen wurden mit GaCl3 hergestellt und zur Bestimmung der IC50-Werte (34,1 µM – 1 µM) in vitro auf ihre Affinität zum MC I getestet. In vivo-Evaluierungen erfolgten mit den zwei potentesten Verbindungen [68Ga]VN160.MZ und [68Ga]VN167.MZ durch µ-PET-Aufnahmen (n=3) in gesunden Ratten über 60 min. Um die Organverteilung ermitteln zu können, wurden ex vivo-Biodistributionsstudien (n=3) vorgenommen. Sowohl die µ-PET-Untersuchungen als auch die Biodistributionsstudien zeigten, dass es bei [68Ga]VN167.MZ zwar zu einer Herzaufnahme kam, die jedoch eher perfusionsabhängig ist. Eine Retention des Tracers im Myokard konnte in geringem Umfang festgestellt werden.

Characterization of Halyomorpha halys (brown marmorated stink bug) biogenic volatile organic compound emissions and their role in secondary organic aerosol formation.

The formation of aerosols is a key component in understanding cloud formation in the context of radiative forcings and global climate modeling. Biogenic volatile organic compounds (BVOCs) are a significant source of aerosols, yet there is still much to be learned about their structures, sources, and interactions. The aims of this project were to identify the BVOCs found in the defense chemicals of the brown marmorated stink bug Halymorpha halys and quantify them using gas chromatography-mass spectrometry (GC/MS) and test whether oxidation of these compounds by ozone-promoted aerosol and cloud seed formation. The bugs were tested under two conditions: agitation by asphyxiation and direct glandular exposure. Tridecane, 2(5H)-furanone 5-ethyl, and (E)-2-decenal were identified as the three most abundant compounds. H. halys were also tested in the agitated condition in a smog chamber. It was found that in the presence of 100-180 ppm ozone, secondary aerosols do form. A scanning mobility particle sizer (SMPS) and a cloud condensation nuclei counter (CCNC) were used to characterize the secondary aerosols that formed. This reaction resulted in 0.23 microg/ bug of particulate mass. It was also found that these secondary organic aerosol particles could act as cloud condensation nuclei. At a supersaturation of 1%, we found a kappa value of 0.09. Once regional populations of these stink bugs stabilize and the populations estimates can be made, the additional impacts of their contribution to regional air quality can be calculated.

Characterization of Halyomorpha Halys (Brown Marmorated Stink Bug) Biogenic Volatile Organic Compound Emissions and Their Role in Secondary Organic Aerosol Formation

The formation of aerosols is a key component in understanding cloud formation in the context of radiative forcings and global climate modeling. Biogenic volatile organic compounds (BVOCs) are a significant source of aerosols, yet there is still much to be learned about their structures, sources, and interactions. The aims of this project were to identify the BVOCs found in the defense chemicals of the brown marmorated stink bug Halymorpha halys and quantify them using gas chromatography-mass spectrometry (GC/MS) and test whether oxidation of these compounds by ozone-promoted aerosol and cloud seed formation. The bugs were tested under two conditions: agitation by asphyxiation and direct glandular exposure. Tridecane, 2(5H)-furanone 5-ethyl, and (E)-2-decenal were identified as the three most abundant compounds. H. halys were also tested in the agitated condition in a smog chamber. It was found that in the presence of 100-180 ppm ozone, secondary aerosols do form. A scanning mobility particle sizer (SMPS) and a cloud condensation nuclei counter (CCNC) were used to characterize the secondary aerosols that formed. This reaction resulted in 0.23 mu g/bug of particulate mass. It was also found that these secondary organic aerosol particles could act as cloud condensation nuclei. At a supersaturation of 1%, we found a kappa value of 0.09. Once regional populations of these stink bugs stablilize and the populations estimates can be made, the additional impacts of their contribution to regional air quality can be calculated. Implications: Halymorpha halys (brown marmorated stink bugs) are a relatively new invasive species introduced in the United States near Allentown, Pennsylvania. The authors chemically speciated the bugs' defense pheromones and found that tridecane, 5-ethyl-2(5H)-furanone, and (E)-2-decenal dominated their emissions. Their defense emissions were reacted with atmospherically relevant concentrations of ozone and resulted in 0.23 g of particulate matter per emission per bug. Due to the large population of these bugs in some regions, these emissions could contribute appreciably to a region's PM2.5 (particulate matter with an aerodynamic diameter 2.5 m) levels.