Crystal growth and nonlinear optical properties of sodium D-isoascorbate monohydrate

Optical quality single crystals of sodium D-isoascorbate monohydrate were grown by a slow cooling technique. The crystal possesses a bulky prismatic morphology. Thermal analyses indicate that the crystals are stable up to 125 degrees C. The optical transmission window ranges from 307 nm to 1450 nm. The principal refractive indices have been measured employing Brewster's angle method. The crystallographic and the principal dielectric axes coincide with each other such that a lies along Z, b along X and c along Y. The optic axis is oriented 58 degrees (at 532 nm) to the crystallographic a axis in the XZ plane and the crystal is negative biaxial. Type 1 and type 2 phase matching curves are generated and experimentally verified. No polarization dependence of the light absorption was observed confirming the validity of Kleinman's symmetry conjecture, leading to a single nonvanishing nonlinear tensor component. According to Hobden's classification the crystal belongs to class 3. The crystal also exhibits second order noncollinear conic sections. The single shot and multiple shot surface laser damage thresholds are determined to be 32.7 GW cm(-2) and 6.5 GW cm(-2) respectively for 1064 nm radiation.

钛宝石强激光负载的有机硅复合凝胶增透膜研究

以硅酸四乙酯(TEOS)和甲基三乙氧基硅烷(MTEOS)为前驱材料，用溶胶-凝胶(sol-gel)方法在钛宝石表面制备得到均匀性良好且具有高激光损伤阈值的有机硅复合凝胶增透膜。膜层在钛宝石激光器输出波段(750～850nm)的增透效果显著，其平均透过率超过98．6％；激光破坏阈值为2．2J／cm^2(800nm，300ps)；膜层表面均匀性达到激光波面的要求，在皮秒、飞秒超短脉冲高功率激光领域具有应用价值。溶胶的性能测试结果表明，溶胶粘度和成膜折射率均随溶液中CH3SiO1.5溶胶体含量的增加而增大，而膜

溶胶-凝胶多孔二氧化硅减反膜稳定性研究

多孔SiO2膜层经热处理后，具有很高的激光破坏阈值，但是结构中有许多Si-OH亲水基团，导致光学透过率受环境相对湿度的影响很大。实验目的是改善膜层内部结构，使膜层结构中的亲水基团转变为疏水基团。提高膜层的疏水性，增强膜层的透过率稳定性。系统地研究了膜层透过率随时间变化的规律，在氨气和六甲基二硅氮烷(HMDS)混合气氛下热处理膜层，处理后生成Si-O-Si(CH2)3非极性疏水基团，使膜层的疏水性大大提高，因而膜层的透过率稳定性有大幅度提高。稳定性的提高延长了膜层的寿命。处理后膜层的表面粗糙度良好，均方根表

高激光损伤阈值溶胶-凝胶ZrO2薄膜

采用醇热法水解氧氯化锆（ZrOCl2·8H2O）制备ZrO2溶胶，提拉法涂膜。采用粘度、粒度分布、折射率、IR、DSC、AFM等测试手段对溶胶和薄膜性能进行表征。结果表明，ZrO2溶胶颗粒的平均粒径为18．9nm，薄膜经300℃热处理后折射率可高达1．95，膜层表面均匀平整，表面平均粗糙度仅为0．561nm，膜层的激光损伤阈值为14J／cm^2（1064nm，1ns）。

甲基化对多孔SiO_2增透薄膜光学稳定性能的影响

分别通过引入甲基三乙氧基硅烷(MTES)、二甲基二乙氧基硅烷(DMDES)以及六甲基二硅氮烷(HMDS)组分对SiO2悬胶体进行改性,得到不同甲基化的多孔SiO2改性薄膜。研究了改性薄膜的光学稳定性,抗激光破坏性能以及机械抗擦性能。结果表明,HMDS改性薄膜的光学稳定性最好而机械抗擦性较弱,MTES与DMDES改性薄膜的光学稳定性较低而机械抗擦性良好且均与改性组分的含量有关,甲基化改性薄膜的抗激光破坏性能比未改性薄膜的有所降低。

透红外含碲氟铝基玻璃的激光损伤阈值

在氟铝酸盐玻璃组分中加入适量声子能量低的重金属氧化物TeO2，得到一种新的氧氟化物玻璃。该材料具有良好的成玻璃性能，适合制作大尺寸红外窗口镜。研究了TeO2含量对玻璃特征温度、阿贝数和红外透过性能的影响。同时测试了这种玻璃的抗DF激光能力，结果表明：TeO2含量为15％的玻璃，DF激光破坏阈值达14．95kW·cm^-2。分析显示，由于玻璃基质的多声子吸收，对激光能量的吸收而引起的热冲击是导致玻璃破坏的主要原因。进一步降低玻璃中水分，可以提高玻璃抗激光破坏性能。

单脉冲和多脉冲飞秒激光对单层光学薄膜的损伤

利用掺钛的蓝宝石飞秒激光系统输出的单脉冲和多脉冲飞秒激光（中心波长800nm，脉宽50fs,靶面聚焦直径Ф40／μm）。分别对BK7玻璃基底上厚约500nm的单层HfO2和单层ZrO2薄膜进行辐照,得到了这两种薄膜在1-on-1和1000-on-1测试方法下的激光损伤阙值。实验发现,两种方法下HfO2单层膜的阈值均比ZrO2单层膜的阈值高。从简化的Keldysh多光子离化理论出发，认为HfO2薄膜材料的带比ZrO2的宽是导致上述结果的主要原因。同时，同一种薄膜的多脉冲下的阙值比单脉冲下的低，原因是多脉冲下

单晶硅材料的1064nmNd：YAG脉冲激光损伤特性研究

作为微电子和光电子系统中普遍使用的一种结构材料，单晶硅一直是人们研究的焦点。长期以来，人们对其电学性质进行了非常深入细致的研究，却疏于对其抗击强激光辐照特性的研究。随着激光通讯和光电对抗技术的发展，对光学材料的激光破坏特性和加固技术进行研究的需求也显得越来越迫切。本文主要对单晶硅的抗激光损伤特性进行研究，研究了单晶硅材料在1064nmNd：YAG激光自由脉冲输出模式和单脉冲输出模式作用下的损伤特性，通过对两种激光作用下单晶硅损伤形貌的分析，在热效应与热力耦合模型的基础上，对单晶硅的激光损伤机制进行了探索。

不同沉积参量下ZrO_2薄膜的微结构和激光损伤阈值

ZrO2采用X射线衍射(XRD)技术分析了不同充氧条件和沉积温度对ZrO2溥膜组成结构的影响，并对不同工艺下制备的薄膜的表面粗糙度和激光损伤阈值进行了测量。结果发现随着氧压的升高，ZrO2溥膜将由单斜相多晶态逐渐转变为非晶态结构，而随着基片温度的增加，溥膜将由非晶态逐渐转变为单斜相多晶态。同时发现随着氧压升高晶粒尺寸减小，而随着沉积温度增加，晶粒尺寸增大。氧压增加时工艺对表面粗糙度有一定程度的改善，而沉积温度升高，工艺对表面粗糙度的改善不明显。晶粒尺寸大小变化与表面粗糙度变化存在对应关系。激光损伤测量表明

脉冲激光辐照光学薄膜的缺陷损伤模型

建立了缺陷吸收升温致薄膜激光损伤模型，该模型从热传导方程出发，考虑了缺陷内部的温度分布以及向薄膜的传导过程，通过引入散射系数简化了Mie散射理论得出的吸收截面．对电子束蒸发沉积的ZrO2：Y2O3单层膜进行了激光破坏实验，薄膜样品的损伤是缺陷引起的，通过辉光放电质谱法对薄膜制备材料的纯度分析发现材料中的主要杂质元素为铂，其含量为0．9％．利用缺陷损伤模型对损伤过程进行了模拟，理论模型和实验结果取得了较好的一致性．

高真空室中的水蒸气对HfO2薄膜性能的影响

本文研究了在镀膜过程中真空室内水蒸气的含量对HfO2薄膜物理性能的影响。用电子束蒸发和光电极值监控的方法在BK7基底上制备HfO2薄膜。利用残余气体分析仪在线监测了真空室内的残余气氛组成。分别用Lambda 900光谱仪、X射线衍射方法、表面热透镜技术和1064nm的激光器测试了薄膜的光学性能、微结构、吸收和激光损伤阈值。实验发现，附加冷阱装置有助于我们有效控制镀膜过程中的水汽含量，且在水蒸气含量较少的真空室内镀制的薄膜具有较高的折射率，较小的晶粒尺寸，较低的弱吸收值和较高的损伤阈值。

薄膜材料对TiO2基薄膜激光损伤阈值的影响

abstract {The optical property, structure, surface properties (roughness and defect density) and laser-induced damage threshold (LIDT) of TiO₂ films deposited by electronic beam (EB) evaporation of TiO₂ (rutile), TiO₂ (anatase) and TiO₂ + Ta₂O₅ composite materials are comparatively studied. All films show the polycrystalline anatase TiO₂ structure. The loose sintering state and phase transformation during evaporating TiO₂ anatase slice lead to the high surface defect density, roughness and extinction coefficient, and low LIDT of films. The TiO₂ + Ta₂O₅ composite films have the lowest extinction coefficient and the highest LIDT among all samples investigated. Guidance of selecting materials for high LIDT laser mirrors is given.}

Ta2O5膜在532, 800 和 1064 nm波长的n-on-1体系下的激光损伤阈值研究

Ta2O5膜采用传统的电子束蒸发方法制备，并在氧气中673 K的条件下进行了退火12 h处理。首先在1-on-1体系下对Ta2O5膜进行了532和1064 nm波长下的激光损伤阈值（LIDT） 研究，然后在n-on-1体系下分别对532，800和1064 nm三种波长下的激光损伤阈值进行了研究。结果表明在n-on-1体系下Ta2O5膜在532和1064 nm波长下的阈值均高于1-on-1体系下的阈值。此外，在n-on-1体系下，薄膜的阈值随波长增加而增大。同时发现，在氧气中进行退火对Ta2O5膜的光学性能

Design of high-efficiency diffraction gratings based on total internal reflection for pulse compressor

We present designs of high-efficiency compression grating based on total internal reflection (TIR) for picosecond pulse laser at 1053 nm. The setup is devised by directly etching gratings into the bottom side of a prism so that light can successfully enter (or exit) the compression grating. Dependence of the -1 order diffraction efficiencies on the constructive parameters is analyzed for TE- and TM-polarized incident light at Littrow angle by using Fourier modal method in order to obtain optimal grating structure. The electric field enhancement within the high-efficiency TIR gratings is regarded as another criterion to optimize the structure of the TIR gratings. With the criterion of high diffraction efficiency, low electric field enhancement and sufficient manufacturing latitude, TIR compression gratings with optimized constructive parameters are obtained for TE- and TM-polarized incident light, respectively. The grating for TE-polarized light exhibits diffraction efficiencies higher than 0.95 within 23 nm bandwidth and relatively low square of electric field enhancement ratio of 5.7. Regardless of the internal electric field enhancement, the grating for TM-polarized light provides diffraction efficiencies higher than 0.95 within 42 nm bandwidth. With compact structure, such TIR compression gratings made solely of fused silica should be of great interest for application to chirped pulse amplification (CPA) systems. (c) 2007 Elsevier B.V. All rights reserved.

Optimization of thin-film design for multi-layer dielectric grating

Thin-film design used to fabricate multi-layer dielectric (MLD) gratings should provide high transmittance during holography exposure, high reflectance at use wavelength and sufficient manufacturing latitude of the grating design making the MLD grating achieve both high diffraction efficiency and low electric field enhancement. Based on a (HLL)H-9 design comprising of quarter-waves of high-index material and half-waves of low-index material, we obtain an optimum MLD coating meeting these requirements by inserting a matching layer being half a quarter-wave of Al2O3 between the initial design and an optimized HfO2 top layer. The optimized MLD coatings exhibits a low reflectance of 0.017% under photoresist at the exposure angle of 17.8 degrees for 413 nm light and a high reflectance of 99.61% under air at the use angle of 51.2 degrees for 1053 nm light. Numerical calculation of intensity distribution in the photoresist coated on the MLD film during exposure shows that standing-wave patterns are greatly minimized and thus simulation profile of photoresist gratings after development demonstrates smoother shapes with lower roughness. Furthermore, a MLD gratings with grooves etched into the top layer of this MLD coating provides a high diffraction efficiency of 99.5% and a low electric field enhancement ratio of 1.53. This thin-film design shows perfect performances and can be easily fabricated by e-beam evaporation. (c) 2006 Elsevier B.V. All rights reserved.