Ultrasensitive thermal lens spectroscopy of water

A recently developed dual-beam configuration that optimizes the thermal lens technique has been used to obtain the absorption spectrum of pure water from 350 to 528 nm. Our results indicate the minimum linear absorption coefficient smaller than 2 X 10(-5) cm(-1) between 360 and 400 nm. This value is lower than previous literature data, and it is blueshifted. Absorption coefficients as small as 2 X 10(-7) cm(-1) can be measured for water using 1 W of excitation power. A detection limit of similar to 6 X 10(-9) cm(-1) (P=1 W) for CCl(4) was estimated, which represents, to the best of our knowledge, the highest sensitivity obtained in small absorption measurements in liquids. (C) 2009 Optical Society of America

Toxicity and recalcitrant compound removal from bleaching pulp plant effluents by an integrated system: anaerobic packed-bed bioreactor and ozone

Effluents originated in cellulose pulp manufacturing processes are usually toxic and recalcitrant, specially the bleaching effluents, which exhibit high contents of aromatic compounds (e.g. residual lignin derivates). Although biological processes are normally used, their efficiency for the removal of toxic lignin derivates is low. The toxicity and recalcitrance of a bleached Kraft pulp mill were assessed through bioassays and ultraviolet absorption measurements, i.e. acid soluble lignin (ASL), UV(280), and specific ultraviolet absorption (SUVA), before and after treatment by an integrated system comprised of an anaerobic packed-bed bioreactor and oxidation step with ozone. Furthermore, adsorbable organic halides (AOX) were measured. The results demonstrated not only that the toxic recalcitrant compounds can be removed successfully using integrated system, but also the ultraviolet absorption measurements can be an interesting control-parameter in a wastewater treatment.

Production and characterization of RF-sputtered PbO-GeO(2) amorphous thin films containing silver and gold nanoparticles

In the present work we report the characterization of PbO-GeO(2) films containing silver nanoparticles (NPs). Radio Frequency (RF) co-sputtering was used for deposition of amorphous films on glass substrates. Targets of 60PbO-40GeO(2) (in wt%) and bulk silver with purity of 99.99% were RF-sputtered using 3.5 m Torr of argon. The concentration of silver and gold NPs in the films was controlled varying the RF-power applied to the targets (40-50W for the PbO-GeO(2) target; 6-8 W for the metallic target). The films obtained were annealed in air at different temperatures and various periods of time. Absorption measurements have shown strong NPs surface plasmon bands. Different widths and peak wavelengths were observed, indicating that size, shape and distribution of the silver NPs are dependent on the deposition process parameters and on the annealing of the samples. X-Ray Fluorescence and Transmission Electron Microscopy were also used to characterize the samples. (C) 2010 Elsevier B.V. All rights reserved.

Structural and optical properties of dilute InAsN grown by molecular beam epitaxy

We perform a structural and optical characterization of InAs1¿xNx epilayers grown by molecular beam epitaxy on InAs substrates x 2.2% . High-resolution x-ray diffraction HRXRD is used to obtain information about the crystal quality and the strain state of the samples and to determine the N content of the films. The composition of two of the samples investigated is also obtained with time-of-flight secondary ion mass spectroscopy ToF-SIMS measurements. The combined analysis of the HRXRD and ToF-SIMS data suggests that the lattice parameter of InAsN might significantly deviate from Vegard"s law. Raman scattering and far-infrared reflectivity measurements have been carried out to investigate the incorporation of N into the InAsN alloy. N-related local vibrational modes are detected in the samples with higher N content. The origin of the observed features is discussed. We study the compositional dependence of the room-temperature band gap energy of the InAsN alloy. For this purpose, photoluminescence and optical absorption measurements are presented. The results are analyzed in terms of the band-anticrossing BAC model. We find that the room-temperature coupling parameter for InAsN within the BAC model is CNM=2.0 0.1 eV.

Drying of Ink in Inkjet Printing

Tämän diplomityön tavoitteena oli saada perustietoa tekijöistä, jotka vaikuttavat musteen kuivumiseen erilaisilla paperipinnoilla inkjet tulostuksessa. Tavoitteena oli saada tietoa erilaisista musteista, joita käytetään yleisimmissä inkjet tulostustekniikoissa, miten paperit vaikuttavat musteen kuivumiseen ja minkälaisia menetelmiä on olemassa musteen kuivumistekijöiden määrittämiseen. Lisäksi tarkoituksena oli varmistaa, voidaanko inkjetmusteiden absorptioajan määrittämiseen käytettävää DIGAT-laitetta käyttää määrittämään ja ennustamaan erilaisten musteiden kuivumista erilaisilla paperipinnoilla sekä etsiä korrelaatioita musteen absorptioajan ja teknisten paperiominaisuuksien sekä inkjet tulostuksen laadun välillä. Kirjallisuusosassa tarkasteltiin erilaisia inkjet tulostusmenetelmiä, niissä käytettäviä musteita ja musteiden koostumuksia. Tutkittiin myös paperin ja musteen välisiä vuorovaikutuksia sekä inkjet tulostuksen laatua. Kokeellisessa osassa tutkittiin musteenabsorboitumista paperiin DIGAT-laitteen avulla. kuudella eri musteella. Paperinäytteistä määritettiin teknisiä paperiominaisuuksia sekä ominaisuuksia, jotka liittyvät inkjet tulostuksen laatuun. Inkjet tulostuksen laatua tarkasteltiin tulostamalla testikuva kolmella eri tulostimella, jotka olivat Canon Bubble Jet i950, HP DeskJet Cxi970 ja Epson Stylus C46. Havaittiin, että DIGAT-laite ei sovellu määrittämään musteen absorptioaikoja kiiltäville näytteille.Tässä tutkimuksessa näyte, jonka kiilto oli 65 %, oli liian kiiltävä mitattavaksi DIGAT-laitteella. Lisäksi absorptiomäärityksissä havaittiin, että erilaiset musteet asettuvat erilailla paperin pintaan ja että pigmenttipohjaisella musteella asettumisaika oli kaikista pisin. Musteiden absorptioajat olivat nopeimpia erikoisinkjetpaperilla ja hitaimpia päällystetyillä, tiiviillä papereilla. Musteen absorptioajan ja teknisten paperiominaisuuksien ja inkjet tulostuksen laadun välisiä korrelaatioita oli vaikea havaita. Voidaan sanoa, että tulokset olivat muste- ja printterikohtaisia. Havaittiin vain muutamia teknisiä paperiominaisuuksia, jotka korreloivat hyvin musteen absorboitumisen kanssa. Nämäolivat Gurley-Hill huokoisuus, paperin tuhka- sekä kalsiumkarbonaattipitoisuus ja K&N värinabsorptio. Myöskään inkjet tulostuksen laadun ja musteen absorption välisiä korrelaatioita ei löytynyt kuin muutama; densiteetti, mottling sekä bleeding. Tämän tutkimuksen perusteella voidaan todeta DIGAT-laitteen soveltuvan hyvin kuvaamaan inkjet tulostuksen laatuominaisuuksista densiteettia, mottlingia sekä bleedingiä. DIGAT-laitetta voidaan siis käyttää avuksi ennustettaessa kuivumisaikaa ja sen vaikutusta edellä mainittuihin ominaisuuksiin. Läpipainatusominaisuuksia DIGAT-laitteen avulla ei voida tutkia, sillä ne ovat enemmän riippuvaisia paperin neliömassasta, paksuudesta ja huokoisuudesta kuinmusteen absorptioajasta. Teknisistä paperiominaisuuksista Gurley-Hill huokoisuus, paperin tuhka-sekä CaCO3-pitoisuus ja K&N värinabsorptio kuvaavat hyvin musteen imeytymisaikaa paperiin, kun taas ominaisuudet Cobb, HST ja polaari- sekädispersiokomponentit eivät kuvaa. Näyttää siltä, että testikuva, joka on tällä hetkellä käytössä UPM Tutkimus-keskuksessa, ei sovellu suurtehotulostuksen laadun tarkkailuun. Testikuva toimii hyvin pöytätulostimilla ja perinteisillä kopiopapereilla ja inkjetpapereilla, jotka on tarkoitettu tulostettaviksi hitaasti. Tulostusnopeuden ja musteen kuivumisnopeuden välisiä ilmiöitä seei tuo esille, joten se ei sovellu kuvaamaan suurtehotulostusta.

A escolha da faixa espectral no uso combinado de métodos espectroscópicos e quimiométricos

A method is presented for the choice of spectral regions when absorption measurements are coupled to chemometric tools to perform quantitative analyses. The method is based on the spectral distribution of the relative standard deviation of concentration (s c/c). It has been applied to the development of PLS-FTNIR calibration models for the determination of density and MON of gasoline, and ethanol content and density of ethanol fuel. The new method was also compared with the correlation (R²) method and has proved to generate PLS calibration models that present better accuracy and precision than those based on R².

Synthesis, properties and characterization of N-Alkyl substituted b-Diketiminato copper(I) Complexes

Le ligand nacnacxylH (xyl = C6Me2H3) et les ligands dikétimines N-alkyle substitués (nacnacCH(Me)PhH, nacnacBnH and nacnaciPrH) ont été préparés avec de bons rendements à l’exception du nacnaciPrH (23%) en utilisant un protocole en une étape et à l’aide d’un montage Dean-Stark. La réaction du S,S-nacnacCH(Me)PhH et du nacnacBnH avec le nBuLi dans le THF conduit au S,S-nacnacCH(Me)PhLi(THF) et au nacnacBnLi(THF). Les tentatives de bromation de ces composés par le N-bromosuccinimide conduisent plutôt aux ligands S,S-succnacnacCH(Me)PhH et succnacnacBnH (succ = succinimido) substitués par un groupement succinimido sur le carbone  La chloration par le N-chlorosuccinimide conduit au produit désiré, mais avec des impuretés. La réaction de ces ligands avec le CuOtBu (ou bien MesCu, où Mes = C6Me3H2, et une quantité catalytique de CuOtBu) en présence de bases de Lewis donne les (nacnacxylCu)2(-toluène), nacnacxylCuCNC6H3(Me)2, nacnacCH(Me)PhCuL (L = PPh3, PMe3, CNC6H3(Me)2, DMAP, lutidine, Py, MeCN), nacnacBnCuL (L = PPh3, CNC6H3(Me)2, styrène, trans-stilbene, phenylvinylether, acrylonitrile, diphenylacetylène), nacnaciPrCuL (L = PPh3, CNC6H3(Me)2, MeCN) et le succnacnacCH(Me)PhCuL (PPh3, CNC6H3(Me)2, pyridine). Tous ces complexes sont jaunes et sensibles à l’air et à l’humidité. En l’absence de fortes bases de Lewis, on n’observe pas de réaction entre les précurseurs de cuivre et les ligands N-alkyle substitués. Les études RMN des complexes dans le C6D6 ne présentent pas de complexe de toluène mais un mélange à l’équilibre du (nacnacxylCu)2(-C6D6) et nacnacxylCu(C6D6) dans une proportion de 2 pour 1. Alors que l’addition de plus de cinquante équivalents soit de THF, soit de toluène n’induit aucun changement des spectres RMN, l’addition de 2 équivalents de MeCN conduit instantanément au complexe nacnacxylCu(MeCN). De plus, le (nacnacxylylCu)2(-C6D6) ne se coordone ni ne réagit avec le N2O, même après avoir été chauffé à 60°C pendant treize jours. En présence de DPA (diphenylacétylène), la réaction du nacnacBnH avec le CuOtBu conduit au dimère ponté (nacnacBnCu)2(µ-DPA). L’addition d’un excès de DPA (10-12 équivalents) transforme le dimère ponté en complexe lié en position terminale nacnacBnCuDPA. Les nacnacRH (R = CH(Me)Ph et i-Pr) ne forment pas de complexe ni avec les oléfines ni avec le DPA. Une réactivité similaire a été observée avec les complexes de nacnacCH(Me)PhCu(NCMe) et nacnaci-PrCu(NCMe). Tandis que le complexe lié en position terminale par MeCN a été isolé et caractérisé, l’équilibre en solution nous laisse suspecter la formation d’un complexe d’acétonitrile ponté. Des études de réactivité comparatives ont été menées sur quelques complexes de cuivre. La Morpholine ne réagit pas avec le nacnacBnCu(acrylonitrile) contrairement à l’acrylonitrile libre. L’expérience de l’échange d’oléfine montre que l’acrylonitrile (une oléfine électro-attractrice) se lie plus fortement que les autres oléfines, mettant ainsi en évidence l’importance de la rétrodonation  face à la donation La rétrodonation est cependant faible comparée aux autres complexes de styrène structurellement caractérisés. Les complexes nacnacCH(Me)PhCuL (L = PPh3 et MeCN) ont été employés dans la cyclopropanation catalytique du styrène et dans l’addition conjuguée du ZnEt2 sur la 2-cyclohexénone, mais les résultats indiquent que le ligand dikétimine est éliminé avant son entrée dans le cycle catalytique. Par conséquent, il n’y a pas d’induction chirale. Les complexes tétra coordinées de cuivre avec les nacnacRCu(phen) (R = Bn, CH(Me)Ph et Phen = 1,10-phenanthroline, 2-Mes-1,10-phenanthroline, 2,9-dimethyl-1,10-phenanthroline (dmp) et 2,9-diphenyl-1,10-phenanthroline (dpp)) ont été synthétisés. Ces complexes sont d’une intense couleur bleue et des interactions d’empilement entre l’un des cycles phényle des ligands nacnac et la phénanthroline ont été observées dans les structures à l’état solide. Les mesures en absorption UV-visible ont été effectuées dans le toluène et les bandes MLCT sont déplacées vers le rouge par rapport à celles des complexes de cuivre et bisphénanthroline. Tous ces composés émettent à l’état solide mais les complexes 1,10-phenanthroline et 2-Mes-1,10-phenanthroline n’émettent pas en solution. Pour renforcer les interactions d’empilement , les nouveaux ligands nacnacRH (R = CH2C6H2(OMe)3, CH2C6F5) et leurs complexes de cuivre respectifs ont été préparés avec du dmp et dpp. Afin de permettre la comparaison, le nacnaciBuCu(dmp) a été synthétisé. Alors que les complexes dmp montrent une augmentation des interactions intramoléculaires - avec les substituants phényle du ligand dikétimine et de la phénanthroline, les complexes dpp ne révèlent pas de telles interactions. Les complexes perfluorés montrent, en absorption et en émission, un déplacement significatif vers le bleu, alors que les complexes substitués par un groupements isobutyle présentent des transitions déplacées vers le rouge. Alors que les intensités de luminescence et les durées de vie sont faibles, les déplacements réduits de Stokes et les pics étroits de luminescence comparables indiquent une réduction des distorsions de l’état excité.

Contrasting the responses of three different ground-based instruments to energetic electron precipitation

In order to make best use of the opportunities provided by space missions such as the Radiation Belt Storm Probes, we determine the response of complementary subionospheric radiowave propagation measurements (VLF), riometer absorption measurements (CNA), and GPS-produced total electron content (vTEC) to different energetic electron precipitation (EEP). We model the relative sensitivity and responses of these instruments to idealised monoenergetic beams of precipitating electrons, and more realistic EEP spectra chosen to represent radiation belts and substorm precipitation. In the monoenergetic beam case, we find riometers are more sensitive to the same EEP event occurring during the day than during the night, while subionospheric VLF shows the opposite relationship, and the change in vTEC is independent. In general, the subionospheric VLF measurements are much more sensitive than the other two techniques for EEP over 200 keV, responding to flux magnitudes two-three orders of magnitude smaller than detectable by a riometer. Detectable TEC changes only occur for extreme monoenergetic fluxes. For the radiation belt EEP case, clearly detectable subionospheric VLF responses are produced by daytime fluxes that are ~10 times lower than required for riometers, while nighttime fluxes can be 10,000 times lower. Riometers are likely to respond only to radiation belt fluxes during the largest EEP events and vTEC is unlikely to be significantly disturbed by radiation belt EEP. For the substorm EEP case both the riometer absorption and the subionospheric VLF technique respond significantly, as does the change in vTEC, which is likely to be detectable at ~3-4 TECu.

Effect of Different Solvent Ratios (Water/Ethylene Glycol) on the Growth Process of CaMoO(4) Crystals and Their Optical Properties

In this paper, calcium molybdate (CaMoO(4)) crystals (meso- and nanoscale) were synthesized by the coprecipitation method using different solvent volume ratios (water/ethylene glycol). Subsequently, the obtained suspensions were processed in microwave-assisted hydrothermal/solvothermal systems at 140 degrees C for 1 h. These meso- and nanocrystals processed were characterized by X-ray diffraction (X R I)), Fourier transform Raman (FT-Raman), Fourier transform infrared (FT-IR). ultraviolet visible (UV-vis) absorption spectroscopies, held-emission gun scanning electron microscopy (FEG-SEM). transmission electron microscopy (TEM). and photoluminescence (PL) measurements. X RI) patterns and FT-Raman spectra showed that these meso- and nanocrystals have a scheelite-type tetragonal structure without the presence of deleterious phases. FT-IR spectra exhibited a large absorption band situated at around 827 cm(-1), which is associated with the Mo-O anti-symmetric stretching vibrations into the [MoO(4)] clusters. FEG-SEM micrographs indicated that the ethylene glycol concentration in the aqueous solution plays an important role in the morphological evolution of CaMoO(4) crystals. High-resolution TEM micrographs demonstrated that the mesocrystals consist of several aggregated nanoparticles with electron diffraction patterns of monocrystal. In addition, the differences observed in the selected area electron diffraction patterns of CaMoO(4) crystals proved the coexistence of both nano- and mesostructures, First-principles quantum mechanical calculations based on the density functional theory at the B3LYP level were employed in order to understand the band structure find density of states For the CaMoO(4). UV-vis absorption measurements evidenced a variation in optical band gap values (from 3.42 to 3.72 cV) for the distinct morphologies. The blue and green PI. emissions observed in these crystals were ascribed to the intermediary energy levels arising from the distortions on the [MoO(4)] clusters clue to intrinsic defects in the lattice of anisotropic/isotropic crystals.

Intrachain Energy Migration to Weak Charge-Transfer State in Polyfluorene End-Capped with Naphthalimide Derivative

Polyfluorene end-capped with N-(2-benzothiazole)-1 8-naphthalimide (PF-BNI) is a highly fluorescent material with fluorescence emission modulated by solvent polarity Its low energy excited state is assigned as a mixed configuration state between the singlet S(1) of the fluorene backbone (F) with the charge transfer (CI) of the end group BNI The triexponential fluorescence decays of PF-BNI were associated with fast energy migration to form an intrachain charge-transfer (ICCT) state polyfluorene backbone decay and ICCT deactivation Time-resolved fluorescence anisotropy exhibited biexponential relaxation with a fast component of 12-16 ps in addition to a slow one in the range 0 8-1 4 ns depending on the solvent showing that depolarization occurs from two different processes energy migration to form the ICCT state and slow rotational diffusion motion of end segments at a longer time Results from femtosecond transient absorption measurements agreed with anisotropy decay and showed a decay component of about 16 ps at 605 nm in PF BNI ascribed to the conversion of S(1) to the ICCT excited state From the ratio of asymptotic and initial amplitudes of the transient absorption measurement the efficiency of intrachain ICCT formation is estimated in 0 5 which means that on average, half of the excited state formed in a BNI-(F)(n)-BNI chain with n = 32 is converted to its low energy intrachain charge-transfer (ICCT) state

Photo-Induced Dipole Relaxation Current in Natural Amethyst

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Uso da palha de carnaúba em revestimento de dutos

In this work, the plant species Copernicia prunifera (Miller) H. E. Moore (carnauba), naturally occurring which prevails in the northeast region of Brazil was the subject of studies aiming its use as external coating of pipelines used in petroleum industry. The part of the plant worked were the leaves, also called straw, which were coated with resinous material. For this purpose, it was necessary to evaluate the effectiveness of the use of acrylic resins in the straw carnauba coating. The properties of the untreated carnauba straw and chemically treated with sodium hydroxide, hexane and carbon tetrachloride were investigated by ATRFTIR, SEM and thermal analysis. The first two techniques showed that treatment with solvents has caused major changes in the straw surface, while the thermal analysis indicated that the sodium hydroxide caused variations in thermal stability of straw constituents. Water absorption measurements showed that treatments have accelerated the absorption process and the reduction of contact angle values for treated samples with solvents indicated higher hidrophilicity of straw. The tensile tests showed lower values of elastic modulus and tensile strength for treated samples. Furthermore, coatings using pure commercial resins A and B as well as the formulations with clay were applied in straw and they were examined once again through thermal analysis, water absorption measurements, contact angle and mechanical tests. To analyze the effect of heat ageing, samples were subjected to tensile tests again in order to assess its resistance. The results showed that the resins/clay formulations increased thermal stability of straw, they promoted a good impermeabilization and caused significant decrease in the values of elastic modulus and tensile strength. Evaluating the ageing effect on the mechanical properties, it has been showed good recovery to the coated straw with the formulations A 60 and A 80% in modulus and tensile strength values and elongation at break values have remained very close. It is thus concluded that the carnauba straw can be used as a coating of pipelines with significant cost savings, since there is no need for pretreatment for its use and shows itself as a viable biotechnology alternative, contributing to the quality of coatings material and environment preservation.

O papel dos modificadores de rede na produção da fotoluminescência no CaWO4

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of hydrogenation on the optical and structural properties of GaAs thin films prepared by rf-magnetron sputtering

We have utilized infra-red and optical absorption measurements, grazing incidence X-ray diffraction (GIXRD) and extended X-ray absorption fine structure (EXAFS) measurements to investigate the influence of hydrogenation on the optical and structural properties of GaAs thin films prepared by rf-magnetron sputtering. Hydrogenation induces distinct changes in the optical properties, namely shifts in the absorption edges and reduction of the Urbach energy. Such modifications are correlated to a reduction in structural disorder as determined by EXAFS and the increase of crystallinity determined by GIXRD. (c) 2005 Elsevier B.V. All rights reserved.

The role of defect states in the creation of photoluminescence in SrTiO3

We discuss the nature of visible photoluminescence at room temperature in amorphous strontium titanate in the light of the results of a recent experimental and quantum mechanical theoretical study. Our calculation of the electronic structure involves the use of first-principles molecular calculations to simulate the variation of the electronic structure in the strontium titanate crystalline phase, which is known to have a direct band gap, and we also make an in-depth examination of amorphous strontium titanate. The results of our simulations of amorphous strontium titanate indicate that the formation of five-fold coordination in the amorphous system may introduce delocalized electronic levels in the highest occupied molecular orbital and the lowest unoccupied molecular orbital. These delocalized electronic levels are ascribed to the formation of a tail in the absorbance-spectrum curve. Optical absorption measurements experimentally showed the presence of a tail. The results are interpreted by the nature of these exponential optical edges and tails associated with defects promoted by the disordered structure of the amorphous material. We associate them with localized states in the band gap.