Interface formation of nanostructured heterojunction SnO 2:Eu/GaAs and electronic transport properties

Thin films of tin dioxide (SnO2) are deposited by the sol-gel-dip-coating technique, along with GaAs layers, deposited by the resistive evaporation technique. The as-built heterojunction has potential application in optoelectronic devices, combining the emission from the rare-earth doped transparent oxide (Eu3+-doped SnO2 presents very efficient red emission) with a high mobility semiconductor. The advantage of this structure is the possibility of separation of the rare-earth emission centers from the electron scattering, leading to a strongly indicated combination for electroluminescence. Electrical characterization of the heterojunction SnO2:Eu/GaAs shows a significant conductivity increase when compared to the conductivity of the individual films, and the monochromatic light irradiation (266 nm) at low temperature of the heterojunction GaAs/SnO2:Eu leads to intense conductivity increase. Scanning electron microscopy (SEM) of the heterojunction cross section shows high adherence and good morphological quality of the interfaces substrate/SnO2 and SnO2/GaAs, even though the atomic force microscopy (AFM) image of the GaAs surface shows disordered particles, which increases with sample thickness. On the other hand, the good morphology of the SnO2:Eu surface, shown by AFM, assures the good electrical performance of the heterojunction. The observed improvement on the electrical transport properties is probably related to the formation of short conduction channels at the semiconductors interface, which may exhibit two-dimensional electron gas (2DEG) behavior. © 2012 Elsevier B.V. All rights reserved.

Changes in the intermediate water mass formation rates in the global ocean for the Last Glacial Maximum, mid-Holocene and pre-industrial climates

The paleoclimate version of the National Center for Atmospheric Research Community Climate System Model version 3 (NCAR-CCSM3) is used to analyze changes in the water formation rates in the Atlantic, Pacific, and Indian Oceans for the Last Glacial Maximum (LGM), mid-Holocene (MH) and pre-industrial (PI) control climate. During the MH, CCSM3 exhibits a north-south asymmetric response of intermediate water subduction changes in the Atlantic Ocean, with a reduction of 2 Sv in the North Atlantic and an increase of 2 Sv in the South Atlantic relative to PI. During the LGM, there is increased formation of intermediate water and a more stagnant deep ocean in the North Pacific. The production of North Atlantic Deep Water (NADW) is significantly weakened. The NADW is replaced in large extent by enhanced Antarctic Intermediate Water (AAIW), Glacial North Atlantic Intermediate Water (GNAIW), and also by an intensified of Antarctic Bottom Water (AABW), with the latter being a response to the enhanced salinity and ice formation around Antarctica. Most of the LGM intermediate/mode water is formed at 27.4 < sigma(theta) < 29.0 kg/m(3), while for the MH and PI most of the subduction transport occurs at 26.5 < sigma(theta) < 27.4 kg/m(3). The simulated LGM Southern Hemisphere winds are more intense by 0.2-0.4 dyne/cm(2). Consequently, increased Ekman transport drives the production of intermediate water (low salinity) at a larger rate and at higher densities when compared to the other climatic periods.

Aerial Rivers and Lakes: Looking at Large-Scale Moisture Transport and Its Relation to Amazonia and to Subtropical Rainfall in South America

This is an observational study of the large-scale moisture transport over South America, with some analyses on its relation to subtropical rainfall. The concept of aerial rivers is proposed as a framework: it is an analogy between the main pathways of moisture flow in the atmosphere and surface rivers. Opposite to surface rivers, aerial rivers gain (lose) water through evaporation (precipitation). The magnitude of the vertically integrated moisture transport is discharge, and precipitable water is like the mass of the liquid column-multiplied by an equivalent speed it gives discharge. Trade wind flow into Amazonia, and the north/northwesterly flow to the subtropics, east of the Andes, are aerial rivers. Aerial lakes are the sections of a moisture pathway where the flow slows down and broadens, because of diffluence, and becomes deeper, with higher precipitable water. This is the case over Amazonia, downstream of the trade wind confluence. In the dry season, moisture from the aerial lake is transported northeastward, but weaker flow over southern Amazonia heads southward toward the subtropics. Southern Amazonia appears as a source of moisture to this flow. Aerial river discharge to the subtropics is comparable to that of the Amazon River. The variations of the amount of moisture coming from Amazonia have an important effect over the variability of discharge. Correlations between the flow from Amazonia and subtropical rainfall are not strong. However, some months within the set of dry seasons observed showed a strong increase (decrease) occurring together with an important increase (decrease) in subtropical rainfall.

Hadron mass spectrum and the shear viscosity to entropy density ratio of hot hadronic matter

Lattice calculations of the QCD trace anomaly at temperatures T < 160 MeV have been shown to match hadron resonance gas model calculations, which include an exponentially rising hadron mass spectrum. In this paper we perform a more detailed comparison of the model calculations to lattice data that confirms the need for an exponentially increasing density of hadronic states. Also, we find that the lattice data is compatible with a hadron density of states that goes as rho(m) similar to m(-a) exp(m/T-H) at large m with a > 5/2 (where T-H similar to 167 MeV). With this specific subleading contribution to the density of states, heavy resonances are most likely to undergo two-body decay (instead of multiparticle decay), which facilitates their inclusion into hadron transport codes. Moreover, estimates for the shear viscosity and the shear relaxation time coefficient of the hadron resonance model computed within the excluded volume approximation suggest that these transport coefficients are sensitive to the parameters that define the hadron mass spectrum.

Nitrogen mass balance in the Brazilian Amazon: an update

The main purpose of this study is to perform a nitrogen budget survey for the entire Brazilian Amazon region. The main inputs of nitrogen to the region are biological nitrogen fixation occurring in tropical forests (7.7 Tg. yr(-1)), and biological nitrogen fixation in agricultural lands mainly due to the cultivation of a large area with soybean, which is an important nitrogen-fixing crop (1.68 Tg. yr(-1)). The input due to the use of N fertilizers (0.48 Tg. yr(-1)) is still incipient compared to the other two inputs mentioned above. The major output flux is the riverine flux, equal to 2.80 Tg. yr(-1) and export related to foodstuff, mainly the transport of soybean and beef to other parts of the country. The continuous population growth and high rate of urbanization may pose new threats to the nitrogen cycle of the region through the burning of fossil fuel and dumping of raw domestic sewage in rivers and streams of the region.

Currents controlling sedimentation, deposits recording palaeo-hydrodynamics – lessons from the continental shelf-slope system off SE South America

The continental margin off SE South America hosts one of the world’s most energetic hydrodynamic regimes but also the second largest drainage system of the continent. Both, the ocean current system as well as the fluvial runoff are strongly controlled by the atmospheric circulation modes over the region. The distribution pattern of particular types of sediments on shelf and slope and the long-term built-up of depositional elements within the overall margin architecture are, thus, the product of both, seasonal to millennial variability as well as long-term environmental trends. This talk presents how the combination of different methodological approaches can be used to obtain a comprehensive picture of the variability of a shelf and upper-slope hydrodynamic system during Holocene times. The particular methods applied are: (a) Margin-wide stratigraphic information to elucidate the role of sea level for the oceanographic and sedimentary systems since the last glacial maximum; (b) Palaeoceanographic sediment proxies combined with palaeo-temperature indicating isotopes of bivalve shells to trace lateral shifts in the coastal oceanography (particularly of the shelf front) during the Holocene; (c) Neodymium isotopes to identify the shelf sediment transport routes resulting from the current regime; (d) Sedimentological/geochemical data to show the efficient mechanism of sand export from the shelf to the open ocean; (e) Diatom assemblages and sediment element distributions indicating palaeo-salinity and the changing marine influence to illustrate the Plata runoff history. Sea level has not only controlled the overall configuration of the shelf but also the position of the main sediment routes from the continent towards the ocean. The shelf front has shifted frequently since the last glacial times probably resulting from both, changes in the Westerly Winds intensity and in the shelf width itself. Remarkable is a southward shift of this front during the past two centuries possibly related to anthropogenic influences on the atmosphere. The oceanographic regime with its prominent hydrographic boundaries led to a clear separation of sedimentary provinces since shelf drowning. It is especially the shelf front which enhances shelf sediment export through a continuous high sand supply to the uppermost slope. Finally, the Plata River does not continuously provide sediment to the shelf but shows significant climate-related changes in discharge during the past centuries. Starting from these findings, three major fields of research should, in general, be further developed in future: (i) The immediate interaction of the hydrodynamic and sedimentary systems to close the gaps between deposit information and modern oceanographic dynamics; (ii) Material budget calculations for the marginal ocean system in terms of material fluxes, storage/retention capacities, and critical thresholds; (iii) The role of human activity on the atmospheric, oceanographic and solid material systems to unravel natural vs. anthropogenic effects and feedback mechanisms

Spin Orbit Effects in the Electronic Transport Properties of Adsorbed Graphene Nanoribbons

Graphene has received great attention due to its exceptional properties, which include corners with zero effective mass, extremely large mobilities, this could render it the new template for the next generation of electronic devices. Furthermore it has weak spin orbit interaction because of the low atomic number of carbon atom in turn results in long spin coherence lengths. Therefore, graphene is also a promising material for future applications in spintronic devices - the use of electronic spin degrees of freedom instead of the electron charge. Graphene can be engineered to form a number of different structures. In particular, by appropriately cutting it one can obtain 1-D system -with only a few nanometers in width - known as graphene nanoribbon, which strongly owe their properties to the width of the ribbons and to the atomic structure along the edges. Those GNR-based systems have been shown to have great potential applications specially as connectors for integrated circuits. Impurities and defects might play an important role to the coherence of these systems. In particular, the presence of transition metal atoms can lead to significant spin-flip processes of conduction electrons. Understanding this effect is of utmost importance for spintronics applied design. In this work, we focus on electronic transport properties of armchair graphene nanoribbons with adsorbed transition metal atoms as impurities and taking into account the spin-orbit effect. Our calculations were performed using a combination of density functional theory and non-equilibrium Greens functions. Also, employing a recursive method we consider a large number of impurities randomly distributed along the nanoribbon in order to infer, for different concentrations of defects, the spin-coherence length.

On the mechanisms that limit oxygen uptake during exercise in acute and chronic hypoxia: role of muscle mass

[EN] Peak aerobic power in humans (VO2,peak) is markedly affected by inspired O2 tension (FIO2). The question to be answered in this study is what factor plays a major role in the limitation of muscle peak VO2 in hypoxia: arterial O2 partial pressure (Pa,O2) or O2 content (Ca,O2)? Thus, cardiac output (dye dilution with Cardio-green), leg blood flow (thermodilution), intra-arterial blood pressure and femoral arterial-to-venous differences in blood gases were determined in nine lowlanders studied during incremental exercise using a large (two-legged cycle ergometer exercise: Bike) and a small (one-legged knee extension exercise: Knee)muscle mass in normoxia, acute hypoxia (AH) (FIO2 = 0.105) and after 9 weeks of residence at 5260 m (CH). Reducing the size of the active muscle mass blunted by 62% the effect of hypoxia on VO2,peak in AH and abolished completely the effect of hypoxia on VO2,peak after altitude acclimatization. Acclimatization improved Bike peak exercise Pa,O2 from 34 +/- 1 in AH to 45 +/- 1 mmHg in CH(P <0.05) and Knee Pa,O2 from 38 +/- 1 to 55 +/- 2 mmHg(P <0.05). Peak cardiac output and leg blood flow were reduced in hypoxia only during Bike. Acute hypoxia resulted in reduction of systemic O2 delivery (46 and 21%) and leg O2 delivery (47 and 26%) during Bike and Knee, respectively, almost matching the corresponding reduction in VO2,peak. Altitude acclimatization restored fully peak systemic and leg O(2) delivery in CH (2.69 +/- 0.27 and 1.28 +/- 0.11 l min(-1), respectively) to sea level values (2.65 +/- 0.15 and 1.16 +/- 0.11 l min(-1), respectively) during Knee, but not during Bike. During Knee in CH, leg oxygen delivery was similar to normoxia and, therefore, also VO2,peak in spite of a Pa,O2 of 55 mmHg. Reducing the size of the active mass improves pulmonary gas exchange during hypoxic exercise, attenuates the Bohr effect on oxygen uploading at the lungs and preserves sea level convective O2 transport to the active muscles. Thus, the altitude-acclimatized human has potentially a similar exercising capacity as at sea level when the exercise model allows for an adequate oxygen delivery (blood flow x Ca,O2), with only a minor role of Pa,O2 per se, when Pa,O2 is more than 55 mmHg.

Räumliche Verbreitung geogener Schwermetallgehalte in Böden des Taunus: Einfluss von periglazialer Deckschichtengenese

Während der Glazialphasen kam es in den europäischen Mittelgebirgen bedingt durch extensive solifluidale Massenbewegungen zur Bildung von Deckschichten. Diese Deckschichten repräsentieren eine Mischung verschiedener Substrate, wie anstehendes Ausgangsgestein, äolische Depositionen und lokale Erzgänge. Die räumliche Ausdehnung der Metallkontaminationen verursacht durch kleinräumige Erzgänge wird durch die periglaziale Solifluktion verstärkt. Das Ziel der vorliegenden Untersuchung war a) den Zusammenhang zwischen den Reliefeigenschaften und den Ausprägungen der solifluidalen Deckschichten und Böden aufzuklären, sowie b) mittels Spurenelementgehalte und Blei-Isotopen-Verhältnisse als Eingangsdaten für Mischungsmodelle die Beitrage der einzelnen Substrate zum Ausgangsmaterial der Bodenbildung zu identifizieren und quantifizieren und c) die räumliche Verteilung von Blei (Pb) in Deckschichten, die über Bleierzgänge gewandert sind, untersucht, die Transportweite des erzbürtigen Bleis berechnet und die kontrollierenden Faktoren der Transportweite bestimmt werden. Sechs Transekte im südöstlichen Rheinischen Schiefergebirge, einschließlich der durch periglaziale Solifluktion entwickelten Böden, wurden untersucht. Die bodenkundliche Geländeaufnahme erfolgte nach AG Boden (2005). O, A, B und C-Horizontproben wurden auf ihre Spurenelementgehalte und teilweise auf ihre 206Pb/207Pb-Isotopenverhältnisse analysiert. Die steuernden Faktoren der Verteilung und Eigenschaften periglazialer Deckschichten sind neben der Petrographie, Reliefeigenschaften wie Exposition, Hangneigung, Hangposition und Krümmung. Die Reliefanalyse zeigt geringmächtige Deckschichten in divergenten, konvexen Hangbereichen bei gleichzeitig hohem Skelettgehalt. In konvergent, konkaven Hangbereichen nimmt die Deckschichtenmächtigkeit deutlich zu, bei gleichzeitig zunehmendem Lösslehm- und abnehmendem Skelettgehalt. Abhängig von den Reliefeigenschaften und -positionen reichen die ausgeprägten Bodentypen von sauren Braunerden bis hin zu Pseudogley-Parabraunerden. Des Weiteren kommen holozäne Kolluvien in eher untypischen Reliefpositionen wie langgestreckten, kaum geneigten Hangbereichen oder Mittelhangbereichen vor. Außer für Pb bewegen sich die Spurenelementgehalte im Rahmen niedriger Hintergrundgehalte. Die Pb-Gehalte liegen zwischen 20-135 mg kg-1. Abnehmende Spurenelementgehalte und Isotopensignaturen (206Pb/207Pb-Isotopenverhältnisse) von Pb zeigen, dass nahezu kein Pb aus atmosphärischen Depositionen in die B-Horizonte verlagert wurde. Eine Hauptkomponentenanalyse (PCA) der Spurenelementgehalte hat vier Hauptsubstratquellen der untersuchten B-Horizonte identifiziert (Tonschiefer, Löss, Laacher-See-Tephra [LST] und lokale Pb-Erzgänge). Mittels 3-Komponenten-Mischungsmodell, das Tonschiefer, Löss und LST einschloss, konnten, bis auf 10 Ausreißer, die Spurenelementgehalte aller 120 B-Horizontproben erklärt werden. Der Massenbeitrag des Pb-Erzes zur Substratmischung liegt bei <0,1%. Die räumliche Pb-Verteilung zeigt Bereiche lokaler Pb-Gehaltsmaxima hangaufwärtiger Pb-Erzgänge. Mittels eines 206Pb/207Pb-Isotopenverhältnis-Mischungsmodells konnten 14 Bereiche erhöhter lokaler Pb-Gehaltsmaxima ausgewiesen werden, die 76-100% erzbürtigen Bleis enthalten. Mit Hilfe eines Geographischen Informationssystems wurden die Transportweiten des erzbürtigen Bleis mit 30 bis 110 m bestimmt. Die steuerenden Faktoren der Transportweite sind dabei die Schluffkonzentration und die Vertikalkrümmung. Diese Untersuchung zeigt, dass Reliefeigenschaften und Reliefposition einen entscheidenden Einfluss auf die Ausprägung der Deckschichten und Böden im europäischen Mittelgebirgsbereich haben. Mischungsmodelle in Kombination mit Spurenelementanalysen und Isotopenverhältnissen stellen ein wichtiges Werkzeug zur Bestimmung der Beiträge der einzelnen Glieder in Bodensubstratmischungen dar. Außerdem können lokale Bleierzgänge die natürlichen Pb-Gehalte in Böden, entwickelt in periglazialen Deckschichten der letzten Vereisungsphase (Würm), bis über 100 m Entfernung erhöhen.

Simulations of charge transport in organic compounds

To aid the design of organic semiconductors, we study the charge transport properties of organic liquid crystals, i.e. hexabenzocoronene and carbazole macrocycle, and single crystals, i.e. rubrene, indolocarbazole and benzothiophene derivatives (BTBT, BBBT). The aim is to find structure-property relationships linking the chemical structure as well as the morphology with the bulk charge carrier mobility of the compounds. To this end, molecular dynamics (MD) simulations are performed yielding realistic equilibrated morphologies. Partial charges and molecular orbitals are calculated based on single molecules in vacuum using quantum chemical methods. The molecular orbitals are then mapped onto the molecular positions and orientations, which allows calculation of the transfer integrals between nearest neighbors using the molecular orbital overlap method. Thus we obtain realistic transfer integral distributions and their autocorrelations. In case of organic crystals the differences between two descriptions of charge transport, namely semi-classical dynamics (SCD) in the small polaron limit and kinetic Monte Carlo (KMC) based on Marcus rates, are studied. The liquid crystals are investigated solely in the hopping limit. To simulate the charge dynamics using KMC, the centers of mass of the molecules are mapped onto lattice sites and the transfer integrals are used to compute the hopping rates. In the small polaron limit, where the electronic wave function is spread over a limited number of neighboring molecules, the Schroedinger equation is solved numerically using a semi-classical approach. The results are compared for the different compounds and methods and, where available, with experimental data. The carbazole macrocycles form columnar structures arranged on a hexagonal lattice with side chains facing inwards, so columns can closely approach each other allowing inter-columnar and thus three-dimensional transport. When taking only intra-columnar transport into account, the mobility is orders of magnitude lower than in the three-dimensional case. BTBT is a promising material for solution-processed organic field-effect transistors. We are able to show that, on the time-scales of charge transport, static disorder due to slow side chain motions is the main factor determining the mobility. The resulting broad transfer integral distributions modify the connectivity of the system but sufficiently many fast percolation paths remain for the charges. Rubrene, indolocarbazole and BBBT are examples of crystals without significant static disorder. The high mobility of rubrene is explained by two main features: first, the shifted cofacial alignment of its molecules, and second, the high center of mass vibrational frequency. In comparsion to SCD, only KMC based on Marcus rates is capable of describing neighbors with low coupling and of taking static disorder into account three-dimensionally. Thus it is the method of choice for crystalline systems dominated by static disorder. However, it is inappropriate for the case of strong coupling and underestimates the mobility of well-ordered crystals. SCD, despite its one-dimensionality, is valuable for crystals with strong coupling and little disorder. It also allows correct treatment of dynamical effects, such as intermolecular vibrations of the molecules. Rate equations are incapable of this, because simulations are performed on static snapshots. We have thus shown strengths and weaknesses of two state of the art models used to study charge transport in organic compounds, partially developed a program to compute and visualize transfer integral distributions and other charge transport properties, and found structure-mobility relations for several promising organic semiconductors.

Aircraft-based in-situ aerosol mass spectrometry: Chemical characterization and source identification of submicron particulate matter in the free and upper troposphere and lower stratosphere

The composition of the atmosphere is frequently perturbed by the emission of gaseous and particulate matter from natural as well as anthropogenic sources. While the impact of trace gases on the radiative forcing of the climate is relatively well understood the role of aerosol is far more uncertain. Therefore, the study of the vertical distribution of particulate matter in the atmosphere and its chemical composition contribute valuable information to bridge this gap of knowledge. The chemical composition of aerosol reveals information on properties such as radiative behavior and hygroscopicity and therefore cloud condensation or ice nucleus potential. rnThis thesis focuses on aerosol pollution plumes observed in 2008 during the POLARCAT (Polar Study using Aircraft, Remote Sensing, Surface Measurements and Models, of Climate, Chemistry, Aerosols, and Transport) campaign over Greenland in June/July and CONCERT (Contrail and Cirrus Experiment) campaign over Central and Western Europe in October/November. Measurements were performed with an Aerodyne compact time-of-flight aerosol mass spectrometer (AMS) capable of online size-resolved chemical characterization of non-refractory submicron particles. In addition, the origins of pollution plumes were determined by means of modeling tools. The characterized pollution episodes originated from a large variety of sources and were encountered at distinct altitudes. They included pure natural emissions from two volcanic eruptions in 2008. By the time of detection over Western Europe between 10 and 12 km altitude the plume was about 3 months old and composed to 71 % of particulate sulfate and 21 % of carbonaceous compounds. Also, biomass burning (BB) plumes were observed over Greenland between 4 and 7 km altitude (free troposphere) originating from Canada and East Siberia. The long-range transport took roughly one and two weeks, respectively. The aerosol was composed of 78 % organic matter and 22 % particulate sulfate. Some Canadian and all Siberian BB plumes were mixed with anthropogenic emissions from fossil fuel combustion (FF) in North America and East Asia. It was found that the contribution of particulate sulfate increased with growing influences from anthropogenic activity and Asia reaching up to 37 % after more than two weeks of transport time. The most exclusively anthropogenic emission source probed in the upper troposphere was engine exhaust from commercial aircraft liners over Germany. However, in-situ characterization of this aerosol type during aircraft chasing was not possible. All long-range transport aerosol was found to have an O:C ratio close to or greater than 1 implying that low-volatility oxygenated organic aerosol was present in each case despite the variety of origins and the large range in age from 3 to 100 days. This leads to the conclusion that organic particulate matter reaches a final and uniform state of oxygenation after at least 3 days in the free troposphere. rnExcept for aircraft exhaust all emission sources mentioned above are surface-bound and thus rely on different types of vertical transport mechanisms, such as direct high altitude injection in the case of a volcanic eruption, or severe BB, or uplift by convection, to reach higher altitudes where particles can travel long distances before removal mainly caused by cloud scavenging. A lifetime for North American mixed BB and FF aerosol of 7 to 11 days was derived. This in consequence means that emission from surface point sources, e.g. volcanoes, or regions, e.g. East Asia, do not only have a relevant impact on the immediate surroundings but rather on a hemispheric scale including such climate sensitive zones as the tropopause or the Arctic.

Fast and accurate numerical solutions in some problems of particle and radiation transport: synthetic acceleration for the method of short characteristics, Doppler-broadened scattering kernel, remote sensing of the cryosphere

The aim of this work is to present various aspects of numerical simulation of particle and radiation transport for industrial and environmental protection applications, to enable the analysis of complex physical processes in a fast, reliable, and efficient way. In the first part we deal with speed-up of numerical simulation of neutron transport for nuclear reactor core analysis. The convergence properties of the source iteration scheme of the Method of Characteristics applied to be heterogeneous structured geometries has been enhanced by means of Boundary Projection Acceleration, enabling the study of 2D and 3D geometries with transport theory without spatial homogenization. The computational performances have been verified with the C5G7 2D and 3D benchmarks, showing a sensible reduction of iterations and CPU time. The second part is devoted to the study of temperature-dependent elastic scattering of neutrons for heavy isotopes near to the thermal zone. A numerical computation of the Doppler convolution of the elastic scattering kernel based on the gas model is presented, for a general energy dependent cross section and scattering law in the center of mass system. The range of integration has been optimized employing a numerical cutoff, allowing a faster numerical evaluation of the convolution integral. Legendre moments of the transfer kernel are subsequently obtained by direct quadrature and a numerical analysis of the convergence is presented. In the third part we focus our attention to remote sensing applications of radiative transfer employed to investigate the Earth's cryosphere. The photon transport equation is applied to simulate reflectivity of glaciers varying the age of the layer of snow or ice, its thickness, the presence or not other underlying layers, the degree of dust included in the snow, creating a framework able to decipher spectral signals collected by orbiting detectors.

Global modeling of pollutant transport and deposition from anthropogenic emission hot spots on global scale

Urban centers significantly contribute to anthropogenic air pollution, although they cover only a minor fraction of the Earth's land surface. Since the worldwide degree of urbanization is steadily increasing, the anthropogenic contribution to air pollution from urban centers is expected to become more substantial in future air quality assessments. The main objective of this thesis was to obtain a more profound insight in the dispersion and the deposition of aerosol particles from 46 individual major population centers (MPCs) as well as the regional and global influence on the atmospheric distribution of several aerosol types. For the first time, this was assessed in one model framework, for which the global model EMAC was applied with different representations of aerosol particles. First, in an approach with passive tracers and a setup in which the results depend only on the source location and the size and the solubility of the tracers, several metrics and a regional climate classification were used to quantify the major outflow pathways, both vertically and horizontally, and to compare the balance between pollution export away from and pollution build-up around the source points. Then in a more comprehensive approach, the anthropogenic emissions of key trace species were changed at the MPC locations to determine the cumulative impact of the MPC emissions on the atmospheric aerosol burdens of black carbon, particulate organic matter, sulfate, and nitrate. Ten different mono-modal passive aerosol tracers were continuously released at the same constant rate at each emission point. The results clearly showed that on average about five times more mass is advected quasi-horizontally at low levels than exported into the upper troposphere. The strength of the low-level export is mainly determined by the location of the source, while the vertical transport is mainly governed by the lifting potential and the solubility of the tracers. Similar to insoluble gas phase tracers, the low-level export of aerosol tracers is strongest at middle and high latitudes, while the regions of strongest vertical export differ between aerosol (temperate winter dry) and gas phase (tropics) tracers. The emitted mass fraction that is kept around MPCs is largest in regions where aerosol tracers have short lifetimes; this mass is also critical for assessing the impact on humans. However, the number of people who live in a strongly polluted region around urban centers depends more on the population density than on the size of the area which is affected by strong air pollution. Another major result was that fine aerosol particles (diameters smaller than 2.5 micrometer) from MPCs undergo substantial long-range transport, with about half of the emitted mass being deposited beyond 1000 km away from the source. In contrast to this diluted remote deposition, there are areas around the MPCs which experience high deposition rates, especially in regions which are frequently affected by heavy precipitation or are situated in poorly ventilated locations. Moreover, most MPC aerosol emissions are removed over land surfaces. In particular, forests experience more deposition from MPC pollutants than other land ecosystems. In addition, it was found that the generic treatment of aerosols has no substantial influence on the major conclusions drawn in this thesis. Moreover, in the more comprehensive approach, it was found that emissions of black carbon, particulate organic matter, sulfur dioxide, and nitrogen oxides from MPCs influence the atmospheric burden of various aerosol types very differently, with impacts generally being larger for secondary species, sulfate and nitrate, than for primary species, black carbon and particulate organic matter. While the changes in the burdens of sulfate, black carbon, and particulate organic matter show an almost linear response for changes in the emission strength, the formation of nitrate was found to be contingent upon many more factors, e.g., the abundance of sulfuric acid, than only upon the strength of the nitrogen oxide emissions. The generic tracer experiments were further extended to conduct the first risk assessment to obtain the cumulative risk of contamination from multiple nuclear reactor accidents on the global scale. For this, many factors had to be taken into account: the probability of major accidents, the cumulative deposition field of the radionuclide cesium-137, and a threshold value that defines contamination. By collecting the necessary data and after accounting for uncertainties, it was found that the risk is highest in western Europe, the eastern US, and in Japan, where on average contamination by major accidents is expected about every 50 years.

Roman aqueducts and calcareous sinter deposits as a proxy for environmental changes

Die im Süden der Türkei gelegen, antiken Städte Aspendos und Patara, waren in der Römerzeit zwei bedeutende Handelszentren mit hoher Bevölkerungsdichte. Aquädukte versorgten beide Städte mit carbonathaltigem Wasser, wobei sich Kalksinter (Calciumcarbonat) in der Kanalrinne ablagerte. Dabei lagern sich im Wechsel eine hellere und dunklere Kalksinterlage ab, die als Sinterpaar bezeichnet wird. Um die Entstehung dieser Sinterpaare besser zu verstehen, und die beteiligten Prozesse mit saisonalen Veränderungen der Umwelt zu korrelieren, werden in der vorliegenden Arbeit laminierten Sinterablagerungen mit geochemischen und petrographischen Methoden untersucht.rnEntlang der Kanalrinne beider Aquädukte wurden an mehreren Stellen Proben entnommen. Es wurde untersucht in wieweit sich die Sinterstruktur aufgrund von Änderungen in der Neigung des Wasserkanals oder des Kanaltyps ändert. Um die Kristallform und die kristallografische Orientierung der Kristalle innerhalb der verschiedenen Sinterpaare zu untersuchen, wurden die entnommenen laminierten Kalksinterablagerungen mit Hilfe optischer Mikroskopie und EBSD (Electron Backscatter Diffraction) analysiert. Der Electron Probe Micro-Analyzer (EPMA) wurde verwendet, um saisonale Schwankungen der Hauptelementverteilung und den Anteil der stabilen Isotope im Wasser zu bestimmen. Die LA-ICP-MS (Laser Ablation-induktiv gekoppeltem Plasma-Massenspektrometrie) Spurenelementanalyse wurde durchgeführt, um kleinste Schwankungen der Spurenelemente zu finden. Basierend auf diesen Analysen wurde festgestellt, dass laminierten Kalksinterablagerungen laterale Änderungen in der Aquäduktstruktur und -neigung, jahreszeitliche Änderungen der Wasserchemie, der Temperatur sowie der Entgasungsrate während eines Jahres widerspiegeln. Die Kalksinterablagerungen zeigen eine deutliche Laminierung in Form von feinkörnig-porösen und grobkörnig-dichten Schichten, die trockene und nasse Jahreszeiten anzeigen. Feinkörnige Schichten zeigen eine hohe Epifluoreszenz aufgrund reichhaltiger organischer Inhalte, die vermutlich eine Folge der bakteriellen Aktivität während der warmen und trockenen Jahreszeit sind. Stabile Sauerstoff und Kohlenstoff-Isotop-Kurven entsprechen auch den jahreszeitlichen Schwankungen der verschiedenen Schichtenpaare. Vor allem δ 18O spiegelt jährliche Veränderungen in der Temperatur und jahreszeitliche Veränderungen des Abflusses wieder. Das wichtigste Ergebnis ist, dass die Periodizität von δ 18O durch Erwärmen des Wassers im Wasserkanal und nicht durch die Verdunstung oder der Brunnenwasser-Charakteristik verursacht wird. Die Periodizität von δ 13C ist komplexer Natur, vor allem zeigen δ 18O und δ 13C eine Antikorrelation entlang der Lamellenpaare. Dies wird wohl vor allem durch Entgasungsprozesse im Aquädukt verursacht. Die Ergebnisse der Spurenelemente sind meist inkonsistent und zeigen keine signifikanten Veränderungen in den verschiedenen Lamellenpaaren. Die Isotope Mg, Sr und Ba zeigen hingegen bei einigen Proben eine positive Korrelation und erreichen Höchstwerte innerhalb feinkörnig-poröser Schichten. Auch sind die Hauptelementwerte von Fe, K, Si und anderer detritischer Elemente innerhalb der feinkörnige-porösen Schichten maximal. Eine genaue Datierung der Kalksinterablagerungen ist wünschenswert, da der Zeitraum, in dem die Aquädukte aktiv waren, bereits archäologisch auf 200-300 Jahre festgelegt wurde. Paläomagnetische und 14C-Datierung geben keine brauchbare Ergebnisse. Die U/Th Isotopie wird durch eine hohe Anfangskonzentration von Th in den Proben behindert. Trotz dieser Schwierigkeiten war eine U/Th Datierung an einem Testbeispiel des Béziers Aquädukt erfolgreich. Mit Hilfe von analogen Untersuchungen an aktiven Wasserkanälen der heutigen Zeit, werden die Ablagerungsmechanismen und die geochemische Entwicklung der laminierten Sinterschichten besser verstanden. Ein weiteres laufendes Projekt dieser Doktorarbeit ist die Überwachung von Sinterabscheidungen und der saisonale Zusammensetzung des Wassers an einigen heute noch aktiven Aquädukten. Das Ziel ist die Untersuchung der jetzigen Calciumcarbonatabscheidungen in Aquäduktkanälen unter den heutigen Umgebungsbedingungen. Erste Ergebnisse zeigen, dass kleine regelmäßige jahreszeitliche Veränderungen in der Isotopenzusammensetzung des Wassers vorliegen, und dass die beobachtete Periodizität der stabilen Isotope aufgrund von Änderungen im eigentlichen Kanal entstanden ist. Die Untersuchung von Kalksinterablagerungen in römischen Aquädukten liefern vielversprechende Ergebnisse, für die Untersuchung des Paläöklimas, der Archaeoseismologie und anderer Umweltbedingungen in der Römerzeit. Diese Studie beschränkt sich auf zwei Aquädukte. Die Untersuchungen weiterer Aquädukte und einer Überwachung, der noch in Betrieb stehenden Aquädukte werden genauere Ergebnisse liefern.

Development and application of mass-spectrometric methods for the quantification and characterization of organic compounds in ice cores

Eisbohrkerne stellen wertvolle Klimaarchive dar, da sie atmosphärisches Aerosol konservieren. Die Analyse chemischer Verbindungen als Bestandteil atmosphärischer Aerosole in Eisbohrkernen liefert wichtige Informationen über Umweltbedingungen und Klima der Vergangenheit. Zur Untersuchung der α-Dicarbonyle Glyoxal und Methylglyoxal in Eis- und Schneeproben wurde eine neue, sensitive Methode entwickelt, die die Stir Bar Sorptive Extraction (SBSE) mit der Hochleistungsflüssigchromatographie-Massenspektrometrie (HPLC-MS) kombiniert. Zur Analyse von Dicarbonsäuren in Eisbohrkernen wurde eine weitere Methode entwickelt, bei der die Festphasenextraktion mit starkem Anionenaustauscher zum Einsatz kommt. Die Methode erlaubt die Quantifizierung aliphatischer Dicarbonsäuren (≥ C6), einschließlich Pinsäure, sowie aromatischer Carbonsäuren (wie Phthalsäure und Vanillinsäure), wodurch die Bestimmung wichtiger Markerverbindungen für biogene und anthropogene Quellen ermöglicht wurde. Mit Hilfe der entwickelten Methoden wurde ein Eisbohrkern aus den Schweizer Alpen analysiert. Die ermittelten Konzentrationsverläufe der Analyten umfassen die Zeitspanne von 1942 bis 1993. Mittels einer Korrelations- und Hauptkomponentenanalyse konnte gezeigt werden, dass die organischen Verbindungen im Eis hauptsächlich durch Waldbrände und durch vom Menschen verursachte Schadstoffemissionen beeinflusst werden. Im Gegensatz dazu sind die Konzentrationsverläufe einiger Analyten auf den Mineralstaubtransport auf den Gletscher zurückzuführen. Zusätzlich wurde ein Screening der Eisbohrkernproben mittels ultrahochauflösender Massenspektrometrie durchgeführt. Zum ersten Mal wurden in diesem Rahmen auch Organosulfate und Nitrooxyorganosulfate in einem Eisbohrkern identifiziert.