Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Tuotannon tunnuslukujen analysointi ja kehittäminen kourukoneilla

Sisäisen suorituskyvyn tehostaminen on yrityksille jatkuvan kehityksen prosessi. Diplomityön tarkoituksena oli selvittää Paroc Oy Ab:n kourukoneiden suorituskykymittarit sekä analysoida ja kehittää niitä. Lisäksi selvitettiin suorituskykyä kuvaavat raporttimallit eri tuotantopaikkakunnilta ja kehitettiin niitä. Teoriaosuudessa kerrotaan, mitä suorituskyvyllä tarkoitetaan sekä käydään läpi sen eri osa-alueita. Siinä esitetään myös suorituskyvyn mittaamista sekä kuinka mittareita suunnitellaan ja rakennetaan. Työn painopiste on kuitenkin empiirisessä osuudessa, jossa ensin kerrotaan työn kohteena olevien kourukoneiden tuotantoprosessi ja tämän jälkeen paneudutaan suorituskykymittareihin ja niiden analysointiin sekä raporttimalleihin. Lopuksi esitetään työn aikana esille nousseita kehitysehdotuksia. Tunnuslukujen selvittämisen tuloksena havaittiin, että kirjallisuus tukee käytössä olevia mittareita. Työssä kerättiin tuotantodataa kourukoneilta usean vuoden aikajaksolta. Datasta valmisteltiin mallit, joita käytettiin mittarien analysointiin. Analysoinnin tuloksena kävi ilmi, että mittarien tarjoama tieto oli joiltakin osin puutteellista ja näin ollen päätöksentekijälle harhaanjohtavaa. Raporttimallit eivät olleet yhtenäisiä paikkakuntien välillä, mikä toi epävarmuutta tuloksiin laskentaperiaatteiden osalta. Työn lopputuloksena tehtiin käytössä oleville suorituskykymittareille kehitysehdotuksia tarkemman ja laadukkaamman tiedon takaamiseksi. Työssä esitettiin myös uusia mittariehdotuksia. Raporttimallit yhtenäistettiin uuden tuotannonohjausjärjestelmän tuomien mahdollisuuksien myötä.

Membrane emulsification in preparation of single site catalyst

In the theory part the membrane emulsification was studied. Emulsions are used in many industrial areas. Traditionally emulsions are prepared by using high shear in rotor-stator systems or in high pressure homogenizer systems. In membrane emulsification two immiscible liquids are mixed by pressuring one liquid through the membrane into the other liquid. With this technique energy could be saved, more homogeneous droplets could be formed and the amount of surfactant could be decreased. Ziegler-Natta and single-site catalysts are used in olefin polymerization processes. Nowadays, these catalysts are prepared according to traditional mixing emulsification. More homogeneous catalyst particles that have narrower particle size distribution might be prepared with membrane emulsification. The aim of the experimental part was to examine the possibility to prepare single site polypropylene catalyst using membrane emulsification technique. Different membrane materials and solidification techniques of the emulsion were examined. Also the toluene-PFC phase diagram was successfully measured during this thesis work. This phase diagram was used for process optimization. The polytetrafluoroethylene membranes had the largest contact angles with toluene and also the biggest difference between the contact angles measured with PFC and toluene. Despite of the contact angle measurement results no significant difference was noticed between particles prepared using PTFE membrane or metal sinter. The particle size distributions of catalyst prepared in these tests were quite wide. This would probably be fixed by using a membrane with a more homogeneous pore size distribution. It is also possible that the solidification rate has an effect on the particle sizes and particle morphology. When polymeric membranes are compared PTFE is probably still the best material for the process as it had the best chemical durability.

Control of Asian soybean rust with mancozeb, a multi-site fungicide

An experiment conducted in the field the action of mancozeb, a fungicide of multi-site action was tested, to control soybean rust caused by Phakopsora pachyrhizi. Its performance was compared to that of the mixture cyproconazole (DMI) + azoxystrobin (QoI). The soybean cultivar NA 7337 RR was used with a population of 400,000 plants/ha cultivated in 20m2 plots. Treatments consisted of mancozeb levels (1.5 and 2.0 kg/ha) applied four, six and eight times. The DMI + QoI mixture was applied three times at 0.3 L/ha + Nimbus. Rust severity was assessed six times in the plots and data were integrated as the area under the disease progress curve (AUDPC). The plots were harvested and grain yield was expressed as kg/ha. Data on AUDPC and yield were subjected to analysis of variance and means compared according to Turkey's test (p = 0.005). Treatments with mancozeb were superior to DMI + QoI mixture both for rust control and grain yield. Four applications of 2.0 k/ha mancozeb were more efficient than three applications of the mixture used as standard. Mancozeb has the potential to be added to fungicide mixtures in the establishment of soybean rust anti-resistance strategy.

Disseminação seletiva da informação na área da saúde: o caso do web site Amedeo

As atividades de produção/divulgação de informações foram otimizadas pela facilidade de comunicação oferecida pela internet, e a produção científica cresce cada vez mais. Com foco nas facilidades de acesso à informação científica oferecidas pela tecnologia, o objetivo é evidenciar os benefícios da aplicação da Disseminação Seletiva da Informação (SDI) na formação de profissionais da saúde, a partir da análise do web site Amedeo. Faz-se um estudo comparativo, de modo a verificar como os artigos disseminados pelo Amedeo podem ser acessados no próprio e numa biblioteca universitária - no caso, analisou-se o acesso através do site do Sistema de Bibliotecas da Unicamp e, ainda, recorre-se à literatura para identificar relações entre a Ciência da Informação e a área de Ciências da Saúde, principalmente quanto à prática da Medicina Baseada em Evidências. Apresentam-se sugestões aos profissionais da informação e professores interessados em identificar possibilidades de uso dos recursos do Amedeo e demais serviços de SDI, em bibliotecas universitárias, de modo a colaborar com o processo educacional dos profissionais da área da saúde.

Dry biomass distribution in a cerrado sensu stricto site in Brazil central

The Cerrado has been the main source of firewood and charcoal in Brazil, but despite being one of the hot spots for conservation of the world's biodiversity, neither plantations of native species nor sustainable management has been adopted in the region. The aim of this work was to investigate the biomass distribution and the potential for energy production of the cerrado species. The study was conducted in a cerrado sensu stricto site at the Água Limpa Farm (15º 56'14'' S and 47º 46'08'' W) in the Cerrado Biosphere Reserve. An area of 63.54ha was divided in 20 x 50m plots and, a random sample consisting of ten of these plots, representing 1.56% of the study-site, was assessed. All woody individuals from 5 cm diameter at 30 cm above ground level were identified and measured. Each individual was felled, the twigs thinner than 3cm were discarded while the larger branches and the trunks, both with bark, were weighted separately. After that, 2.5cm transverse sections of the trunk with bark were taken at 0, 25, 50, 75 and 100% of the length. A similar sample was also taken at the base of each branch. A total of 47 species in 35 genera and 24 families were found, with an average density of 673 individuals per ha. The diameter distribution showed a reversed-J shape with 67% of the individuals up to 13cm, while the maximum diameter was 32.30cm. Seven species represented 72% of the total biomass. In general, the species with higher production per tree were among those with higher production per ha. This content was distributed by diameter classes, reaching a maximum of 2.5ton/ha between 9 to 13cm and then, decreasing to 0.96 ton/ha between 29 to 33cm diameter. Carbon sequestering was 6.2ton/ha (until the actual stage of cerrado) based on an average 50% carbon content in the dry matter. The heat combustion of the wood varied from 18,903kj/kg to 20,888kj/kg with an average of 19,942kj/kg. The smaller diameter classes fix more carbon due to the large number of small plants per ha. But, for a species that reached larger dimensions and contained individuals in all diameter classes, Vochysia thyrsoidea, one can verify an increase in carbon fixation from 1.41 kg/ha in the first class (5 to 9cm) to 138,3kg/ha in the last (25 to 33cm). That indicates that it is possible to select species that reach larger size with a higher capacity of carbon accumulation per plant. The species that reached larger dimensions, with a production per tree above average and had high calorific power values were Dalbergia miscolobium, Pterodon pubescens and Sclerolobium paniculatum. These species have potential for use in fuelwood plantations and sustainable management.

Kokemäenjoen suiston kehitys, maaperämuodostumat ja niiden kemialliset piirteet

Suurelta osin Natura-alueeseen kuuluvan Kokemäenjoen suistoalueen kuivan maan ja suiston edustan vesialueen erityyppisten maaperäkerrostumien kerrosjärjestys ja alueellinen jakautuminen selvitettiin pintamaaperän kartoituksella, tutkimuskaivannoilla ja kairauksella. Suiston kerrostumat luokiteltiin viiteen maaperämuodostumaan. Vanhimmasta nuorimpaan, Toukari, Vainio-Mattila, Hevosluoto, Lanajuopa ja Säikkä muodostumaan. Nämä edustavat vanhoja Itämeren altaan ja nuorempia merelle päin etenevän suiston eri osien kerrostumisympäristöjä. Eri muodostumien fysikaaliset ja kemialliset ominaisuudet kuvattiin ja ne eroavat luonteeltaan ratkaisevasti toisistaan. Suiston etenemistä edustavat Hevosluoto- ja Säikkä-muodostumat ovat kontaminoituneet 1900-luvun alkupuolelta lähtien yhä voimakkaammin ihmistoiminnasta kertyvistä raskasmetallipitoisuuksista ja orgaanisista haitta-aineista. Tämä näkyy erityisesti elohopean, kadmiumin, arseenin, lyijyn, sinkin, nikkelin, dioksiinien ja furaanien kokonaispitoisuuksien kasvuna näissä muodostumissa. Pitoisuudet ovat suurimpia muodostumien nuorimmissa osissa. Kuivalla maalla raskasmetallipitoisuudet ylittävät paikoin valtioneuvoston pilaantuneelle maaperälle asettamat kynnysarvot, jolloin säädökset on huomioitava suiston maaperää muokattaessa. Vesialueella nämä kynnysarvot ylittyvät myös orgaanisten haitta-aineiden osalta. Tietyin osin ovat esimerkiksi arseenin ja nikkelin osalta taustapitoisuudet suistoalueen vanhimmassa Toukari muodostumassa jo luontaisesti kynnysarvoja suuremmat. Tämä pitää osata ottaa huomioon maansiirtotoimenpiteitä suunniteltaessa. Suistoon kerrostuvan maa-aineksen ja nopean maankohoamisen vuoksi suisto etenee nykyisin 30-40 m vuodessa merialueelle päin. Tämä mataloittaa vääjäämättömästi suiston edustan vesialueita kerrostumisen siirtyessä merelle päin. Näin myös Natura-alueen ainutlaatuiset biotoopit vähitellen siirtyvät merelle päin.

Testate amoebae (thecamoebians) as indicators of aquatic mine impact

The environmental impacts of a single mine often remain local, but acidic and metal-rich acid mine drainage (AMD) from the waste materials may pose a serious threat to adjacent surface waters and their ecosystems. Testate amoebae (thecamoebian) analysis was used together with lake sediment geochemistry to study and evaluate the ecological effects of sulphidic metal mines on aquatic environments. Three different mines were included in the study: Luikonlahti Cu-mine in Kaavi, eastern Finland, Haveri Cu-Au mine in Ylöjärvi, southern Finland and Pyhäsalmi Zn-Cu-S mine in Pyhäjärvi, central Finland. Luikonlahti and Haveri are closed mines, but Pyhäsalmi is still operating. The sampling strategy was case specific, and planned to provide a representative sediment sample series to define natural background conditions, to detect spatial and temporal variations in mine impacts, to evaluate the possible recovery after the peak contamination, and to distinguish the effects of other environmental factors from the mining impacts. In the Haveri case, diatom analyses were performed alongside thecamoebian analysis to evaluate the similarities and differences between the two proxies. The results of the analyses were investigated with multivariate methods (direct and indirect ordinations, diversity and distance measure indices). Finally, the results of each case study were harmonized, pooled, and jointly analyzed to summarize the results for this dissertation. Geochemical results showed broadly similar temporal patterns in each case. Concentrations of ions in the pre-disturbance samples defined the natural baseline against which other results were compared. The beginning of the mining activities had only minor impacts on sediment geochemistry, mainly appearing as an increased clastic input into the lakes at Haveri and Pyhäsalmi. The active mining phase was followed by the metallic contamination and, subsequently, by the most recent change towards decreased but still elevated metal concentrations in the sediments. Because of the delay in the oxidation of waste material and formation of AMD, the most intense, but transient metal contamination phase occurred in the post-mining period at Luikonlahti and Haveri. At Pyhäsalmi, the highest metal contamination preceded effluent mitigation actions. Spatial gradients were observed besides the temporal evolution in both the pre-disturbance and mine-impacted samples from Luikonlahti and Pyhäsalmi. The geochemical gradients varied with distance from the main source of contaminants (dispersion and dilution) and with water depth (redox and pH). The spatial extent of the highest metal contamination associated with these mines remained rather limited. At Haveri, the metallic impact was widespread, with the upstream site in another lake basin found to be contaminated. Changes in thecamoebian assemblages corresponded well with the geochemical results. Despite some differences, the general features and ecological responses of the faunal assemblages were rather similar in each lake. Constantly abundant strains of Difflugia oblonga, Difflugia protaeiformis and centropyxids formed the core of these assemblages. Increasing proportions of Cucurbitella tricuspis towards the surface samples were found in all of the cases. The results affirmed the indicator value of some already known indicator forms, but such as C. tricuspis and higher nutrient levels, but also elicited possible new ones such as D. oblonga ‘spinosa’ and clayey substrate, high conductivity and/or alkalinity, D. protaeiformis ‘multicornis’ and pH, water hardness and the amount of clastic material and Centropyxis constricta ‘aerophila’ and high metal and S concentrations. In each case, eutrophication appeared to be the most important environmental factor, masking the effects of other variables. Faunal responses to high metal inputs in sediments remained minor, but were nevertheless detectable. Besides the trophic state of the lake, numerical methods suggested overall geochemical conditions (pH, redox) to be the most important factor at Luikonlahti, whereas the Haveri results showed the clearest connection between metals and amoebae. At Pyhäsalmi, the strongest relationships were found between Ca- and S-rich present loading, redox conditions and substrate composition. Sediment geochemistry and testate amoeba analysis proved to be a suitable combination of methods to detect and describe the aquatic mine impacts in each specific case, to evaluate recovery and to differentiate between the effects of different anthropogenic and natural environmental factors. It was also suggested that aquatic mine impacts can be significantly mitigated by careful design and after-care of the waste facilities, especially by reducing and preventing AMD. The case-specific approach is nevertheless necessary because of the unique characteristics of each mine and variations in the environmental background conditions.

Kompostipiireissä opittua : Eloperäiset jätteet kiertoon -hanke

Kompostien käyttöä on kokeiltu ja tutkittu Kainuun ELY-keskuksen Eloperäiset jätteet kiertoon -hankkeessa. Komposteja on hyödynnetty laskettelurinteen ja kaivosteollisuuden sivukiven läjitysalueen maisemoinnissa, pihanurmen ja energiakasvien kasvattamisessa, metsän lannoittamisessa ja maanviljelyssä. Pihanurmen perustamisen ja energiakasvien kasvattamisen kokeiluista on tehty myös erilliset tutkimukset. Tutkimustyöstä on vastannut MTT (Maa- ja elintarviketalouden tutkimuskeskus). Tutkimustieto on sisällytetty tähän julkaisuun. Kompostin käyttökokeissa ja tutkimuksissa on hyödynnetty Kainuun kuntien ja Kainuun jätehuollon kuntayhtymän Eko-Kympin komposteja. Kaikki kompostit ovat aumakompostoinnin tuotoksia. Eko-Kympin komposti on valmistettu biojätteistä. Muut kompostit ovat lähtöisin kunnallisten jätevedenpuhdistamoiden lietteistä. Kajaanin kompostia kutsutaan myös A. & E. Juntunen Oy:n valmistamaksi biomullaksi. Saatujen kokemusten ja tutkimusten mukaan aumakompostoinnilla tuotettu komposti soveltuu näihin erilaisiin käyttömuotoihin, etenkin kun esille tulleita kehittämistoimia toteutetaan. Sivukiven läjitysalueiden maisemoinnissa, maanviljelyssä ja metsän lannoittamisessa komposti ei tarvitse kivennäismaata seosaineeksi. Sivukiven läjitysalueilla ne kompostit, joihin oli sekoitettu hiekkaa, eivät pysyneet paikoillaan. Aines valui sadeveden mukana alas rinteeltä. Pelkkää kompostia käytettäessä kompostimassa pysyi aloillaan. Maanviljelyssä ja metsän lannoittamisessa kivennäismaa on tarpeeton. Lisäksi kompostissa oleva kiviaines kuluttaa ja voi vaurioittaa levityslaitteita. Ravinteet vapautuvat kompostista hitaasti kasvien käyttöön. Kemiallisilla lannoitteilla on nopeampi vaikutus. Kompostit soveltuvat erityisen hyvin ympäristöihin, joissa täydennyslannoitusta ei tarvita tai joissa lannoite on vaikeaa levittää. Tällaisia kohteita ovat esimerkiksi kaivosten sivukiven tai rikastushiekan läjitysalueet tai muut vaikeakulkuiset kohteet. Myös metsien lannoittaminen ja maanviljely ovat Kainuussa kompostien hyödyntämisen osalta alihyödynnettyjä. Pöyry Finland Oy on laatinut Kajaaniin kaavaillulle biologiselle jätteiden käsittelylaitokselle teknistaloudelliset suunnitelmat. Yhtiön tekemissä suunnitelmissa tulee ilmi, että kaikkien Kainuun lietteiden aumakompostointi tuottaisi kompostia 13 000 tonnia vuodessa, kun tukiaine seulotaan erilleen. Mädätys- tai biokaasulaitosvaihtoehdoissa lopputuotteen määrä on edellistä pienempi. Pelkkien Kainuun lietteiden mädättäminen tuottaisi kompostia jälkikompostin seulonnan jälkeen 6 600 tonnia. Viherrakentaminen taajamissa on komposteille Kainuussa yleinen käyttömuoto. Sillä on kasvun edellytyksiä etenkin, kun kompostin laatuun panostetaan. Viherrakentaminen Kajaanin seudulla riittäisi kuluttamaan kaiken Kainuussa muodostuvan kompostin, kun kompostimullan kulutuksena pidetään 0,5 tonnia asukasta kohden vuodessa. Tämä vastaa Kajaanin seudulla 27 000 tonnin kompostimäärää. Kompostin muodostumismäärä ei tulevaisuudessa tule olemaan lähellä tätä laskennallista multamenekkiä. Kompostin huono menekki johtuu joidenkin kuntien osalta pikemminkin huonosta kompostin laadusta kuin markkinoiden kyllästymisestä. Tilanne on korjaantumassa suunnitteilla olevan biologisen jätteiden käsittelylaitoksen myötä. Siinä kompostituotteen laatuun voidaan panostaa tehokkaammin kuin erillisillä pienillä kompostointikentillä.

On-site calibration of a phase fraction meter by an inverse technique

The formal calibration procedure of a phase fraction meter is based on registering the outputs resulting from imposed phase fractions at known flow regimes. This can be straightforwardly done in laboratory conditions, but is rarely the case in industrial conditions, and particularly for on-site applications. Thus, there is a clear need for less restrictive calibration methods regarding to the prior knowledge of the complete set of inlet conditions. A new procedure is proposed in this work for the on-site construction of the calibration curve from total flown mass values of the homogeneous dispersed phase. The solution is obtained by minimizing a convenient error functional, assembled with data from redundant tests to handle the intrinsic ill-conditioned nature of the problem. Numerical simulations performed for increasing error levels demonstrate that acceptable calibration curves can be reconstructed, even from total mass measured within a precision of up to 2%. Consequently, the method can readily be applied, especially in on-site calibration problems in which classical procedures fail due to the impossibility of having a strict control of all the input/output parameters.

Sorbent characterization for circulating fluidized bed scrubbers

Harmful sulfur dioxide (SO2) emissions from power plants have increasingly been restricted since the 1970’s. Circulating fluidized bed (CFB) scrubber is a dry flue gas desulfurization method of absorbing SO2 out of the flue gas with sorbent. In current commercial plants, the used sorbent is commercial or on-site hydrated calcium hydroxide. The CFB scrubber process is characterized by a close but adequate approach to the flue gas saturation temperature that is achieved by spraying water to the absorber followed by a particulate control device. Very high SO2 removal is achieved along with a dry byproduct that is continuously recirculated back to the absorber for enhanced sorbent utilization. The aim of this work is to develop a method that would characterize the reactivity of sorbents used in CFB scrubbers and to conclude how different process parameters and sorbent properties affect the sulfur absorption. The developed characterization method is based on a fixed bed of sorbent and inert silica sand, through which an SO2 containing gas mixture is led. The reaction occurs in the bed and the SO2 concentration in the outlet as a function of time, a breakthrough curve, is obtained from the analyzer. Reactivity of the sorbents are evaluated by the absorbed sulfur amount. Results suggest that out of process parameters, lower SO2 concentration, lower temperature and higher moisture content enhance the desulfurization. Between different sorbents, specific surface area seems to be the most significant parameter. Large surface area linearly leads to more efficient desulfurization. Overall, the solid conversion levels in the tests were very low creating uncertainty to the validity of the results. New desing is being planned to overcome the problems of the device.

Effect of dose and application site on quinclorac absorption by barnyardgrass biotypes

This work aimed to evaluate the uptake and translocation of quinclorac in function of application sites (shoot or roots) by Echinochloa crusgalli biotypes resistant and susceptible to this herbicide. The treatments consisted of quinclorac doses (0; 0.5; 1; 2; 4; 16 and 64 ppm), applied on the shoot or roots of seedlings of barnyardgrass biotypes. The experimental units consisted of plastic cups containing 250 cm³ of sand. The treatments were applied 10 days after emergence, when barnyardgrass plants reached a 2- to 3- leaf growth stage. The barnyardgrass biotypes were irrigated with nutritive solution weekly and maintained for 40 days after emergence, when length, fresh and dry matter of shoot and roots were evaluated. Variance analysis was carried out using the F test at 5% probability, and in case of significance, a non-linear regression analysis was also carried out using a three-parameter logistic model. In the susceptible biotype, quinclorac was more absorbed by the roots than by the shoot. Comparing dry mass production of the different plant parts of the susceptible biotype per application site, it was verified that quinclorac action is higher when applied to the plant roots. However, for the resistant biotype, it was not possible to determine the dose causing 50% reduction in dry mass accumulation (GR50) and in the resistance index (RI) between both biotypes, due to its high resistance to quinclorac (128 times the recommended dosage). The results showed that quinclorac resistance by the evaluated biotype is not due to differences in the absorption site, strongly suggesting that the resistance acquired by the biotype may result from alteration in the target site.

A Modified phosphate-carrier protein theory is proposed as a non-target site mechanism For glyphosate resistance in weeds

Glyphosate is an herbicide that inhibits the enzyme 5-enolpyruvyl-shikimate-3-phosphate synthase (EPSPs) (EC 2.5.1.19). EPSPs is the sixth enzyme of the shikimate pathway, by which plants synthesize the aromatic amino acids phenylalanine, tyrosine, and tryptophan and many compounds used in secondary metabolism pathways. About fifteen years ago it was hypothesized that it was unlikely weeds would evolve resistance to this herbicide because of the limited degree of glyphosate metabolism observed in plants, the low resistance level attained to EPSPs gene overexpression, and because of the lower fitness in plants with an altered EPSPs enzyme. However, today 20 weed species have been described with glyphosate resistant biotypes that are found in all five continents of the world and exploit several different resistant mechanisms. The survival and adaptation of these glyphosate resistant weeds are related toresistance mechanisms that occur in plants selected through the intense selection pressure from repeated and exclusive use of glyphosate as the only control measure. In this paper the physiological, biochemical, and genetic basis of glyphosate resistance mechanisms in weed species are reviewed and a novel and innovative theory that integrates all the mechanisms of non-target site glyphosate resistance in plants is presented.

Resistance to ACCase inhibitors in Eleusine indica from Brazil involves a target site mutation

Eleusine indica (goosegrass) is a diploid grass weed which has developed resistance to ACCase inhibitors during the last ten years due to the intensive and frequent use of sethoxydim to control grass weeds in soybean crops in Brazil. Plant dose-response assays confirmed the resistant behaviour of one biotype obtaining high resistance factor values: 143 (fenoxaprop), 126 (haloxyfop), 84 (sethoxydim) to 58 (fluazifop). ACCase in vitro assays indicated a target site resistance as the main cause of reduced susceptibility to ACCase inhibitors. PCR-generated fragments of the ACCase CT domain of the resistant and sensitive reference biotype were sequenced and compared. A point mutation was detected within the triplet of aspartate at the amino acid position 2078 (referred to EMBL accession no. AJ310767) and resulted in the triplet of glycine. These results constitute the first report on a target site mutation for a Brazilian herbicide resistant grass weed.

The site of self-incompatibility action in cupuassu (Theobroma grandiflorum)

Cupuassu (Theobroma grandiflorum (Willd. ex Spreng.) Schumann) is a fruit tree that is attracting attention in Brazil and also in other tropical countries. Its pulp is used to prepare ice-cream, juices, jellies and many other home-made sweets. This species has a very low fecundity, attributed to problems with pollination and self-incompatibility, noted as being restrictive to the agronomic productivity of the species. Controlled pollinations between compatible and incompatible parents were made and flowers were collected at three times: 24, 48 and 72 h after pollinations, during the floral seasons of 1995 and 1998. In flowers collected 24 h after pollination, in both compatible and incompatible crosses, around 70% of ovules showed egg apparatus without evidences of sperm cell delivery; nevertheless some pollen tubes had been observed. Ovaries collected at 48 h showed different behaviors according to the type of cross. In the compatibles, 35% of ovules did not show evidences of gamete fusion. In incompatible crosses this number rose to 50%. Collected ovaries with 72 h, from compatible and incompatible crosses, showed respectively 1.2% and 14.2% of the ovules with the egg apparatus and polar nuclei only. In these ovaries, for the two types of crosses, the presence of sperm nuclei was common and the zygote was still undivided. The incompatibility action is occurring after fertilization, in a late self-incompatibility action.