Cinética e modelação da secagem convectiva de papel obtido a partir de fibras de algodão

No presente trabalho pretende-se caraterizar a cinética de secagem de papel obtido partir de fibra de algodão. A componente experimental é executada com recurso a uma estação de secagem, munida com equipamentos de controlo e de leitura. O objetivo é realizar a análise da cinética de secagem, com base nas condições impostas através dos parâmetros de entrada, temperatura a humidade relativa e velocidade do ar de secagem. Os resultados permitem determinar a influência dos parâmetros temperatura, humidade relativa, velocidade do escoamento e espessura do material sobre a cinética de secagem. Foi determinada a difusividade em cada ensaio e desenvolvido e validado um modelo matemático de secagem, com recurso aos valores obtidos experimentalmente. A modelação da secagem é realizada através de um modelo que recorre à segunda lei de Fick. São apresentados os resultados da modelação e respetivos desvio padrão relativamente aos valores experimentais.

Understanding the Reaction Mechanism of Nanocomposite Thermites

Nanocomposite energetics are a relatively new class of materials that combine nanoscale fuels and oxidizers to allow for the rapid release of large amounts of energy. In thermite systems (metal fuel with metal oxide oxidizer), the use of nanomaterials has been illustrated to increase reactivity by multiple orders of magnitude as a result of the higher specific surface area and smaller diffusion length scales. However, the highly dynamic and nanoscale processes intrinsic to these materials, as well as heating rate dependencies, have limited our understanding of the underlying processes that control reaction and propagation. For my dissertation, I have employed a variety of experimental approaches that have allowed me to probe these processes at heating rates representative of free combustion with the goal of understanding the fundamental mechanisms. Dynamic transmission electron microscopy (DTEM) was used to study the in situ morphological change that occurs in nanocomposite thermite materials subjected to rapid (10^11 K/s) heating. Aluminum nanoparticle (Al-NP) aggregates were found to lose their nanostructure through coalescence in as little as 10 ns, which is much faster than any other timescale of combustion. Further study of nanoscale reaction with CuO determined that a condensed phase interfacial reaction could occur within 0.5-5 µs in a manner consistent with bulk reaction, which supports that this mechanism plays a dominant role in the overall reaction process. Ta nanocomposites were also studied to determine if a high melting point (3280 K) affects the loss of nanostructure and rate of reaction. The condensed phase reaction pathway was further explored using reactive multilayers sputter deposited onto thin Pt wires to allow for temperature jump (T-Jump) heating at rates of ~5x10^5 K/s. High speed video and a time of flight mass spectrometry (TOFMS) were used to observe ignition temperature and speciation as a function of bilayer thickness. The ignition process was modeled and a low activation energy for effective diffusivity was determined. T-Jump TOFMS along with constant volume combustion cell studies were also used to determine the effect of gas release in nanoparticle systems by comparing the reaction properties of CuO and Cu2O.

Microstructures layering, mechanisms in the middle waters of the Persian Gulf

Layered structures, known as micro structures in marine environments are common features of which their formation mechanisms are first reviewed. Some methods of measuring such features based on the measurements and theories are presented for the Persian Gulf. This includes determination of layers with temperature inversion (TI) associated with double diffusive convection (DDC). The relevant associated parameters are estimated from ROPME CTD data for late winter and early summer of 1992. Only in certain parts temperature inversion and DDC are observed which seem to produce layered structures. Observations show that the places with TI and DDC are mainly confined to the frontal regions where the water entering the Persian Gulf and water exiting it meet, nearly along the axis of the Gulf. TI and DDC is mainly observer in the northern bound of the front. Typical density ratio for regions with TI and DDC is 0.7 to 0.2 and the mean depth is at about 37 ± 3 m for the Persian Gulf. TI and DDC are also found in the outflow from the Persian Gulf to the Oman Gulf which is found to be at a depth of about 250 m. Horizontal addiction and reduction of solar heating seem to be the main reasons in producing layers with TI and DDC. It is also found that the regime of DDC in the Persian Gulf is more diffusive and the flow associated with intrusion layers with TI is non-isopycnal (more unstable). However for the Oman sea both diffusive and finger regime are observed and the flow is inferred to be isopycnal (more stable statically). Typical heat and salt fluxes due to DDC are found to be 6 W/m2 and 0.36 W/m2 respectively. Effective salinity diffusivity, Ks and heat diffusivity, Kr have been estimated for the places with DDC in the Persian Gulf and Oman Gulf (Ks=1.1 *10-7 m2/s, KT= 1.88*10-6 m2/s). Their values are within the values obtained by others. The buoyancy frequency for the Persian Gulf with typical mean value of 0.05s-1 is much higher than these of the free Oceans. Such large values of N (typically 0.05 s-1) indicate that processes such as tide can produce strong internal waves which may be another factor in producing layered structures. This requires separate study.

Three dimensional circulation of water with variable wind in the Caspian Sea

This research is based on a numerical model for forecasting the three-dimensional behavior of (sea) water motion due to the effect of a variable wind velocity. The results obtained are then analyzed and compared with observation. This model is based on the equations that overcome the current and distribution of temperature by applying the method of finite difference with assuming Δx, Δy as constant and Δz, variable. The model is based on the momentum equation, continuity equation and thermodynamic energy equation and tension at the surface and middle layers and bottom stress. The horizontal and vertical eddy viscosity and thermal diffusivity coefficients we used in accordance with that of the Bennet on Outario Lake (1977). Considering the Caspian Sea dimension in numerical model the Coriolis parameter used with β effects and the approximation Boussines have been used. For the program controlling some simple experiment with boundary condition similar to that of the Caspian Sea have been done. For modeling the Caspian Sea the grid of the field was done as follows: At horizontal surface grid size is 10×10km extension and at vertical in 10 layers with varying thickness from surface to bed respectively as: 5, 10, 20, 3, 50, 100, 150, 200, 25, 500 and higher. The data of wind as velocity، direction and temperature of water related to 15th September 1995 at 6،12 and 18 o’clock were obtained from synoptic station at the Caspian Sea shore and the research marine of Haji Alief. The information concerning shore wind was measured and by the method of SPM (shore protection manual) was transferred to far shore winds through interpolation and by use of inverse square distance of position distribution of the wind velocity at the Caspian surface field was obtained. The model has been evaluated according to the reports and observations. Through studying the position of the current in different layers، the velocity in the cross section in the northern، southern and the middle layers، will be discussed. The results reveal the presence of the circulation cells in the three above mentioned areas. The circulation with depth is reduced too. The results obtained through the numerical solution of the temperature equation have been compared with the observation. The temperature change in different layers in cross section illustrates the relative accordance of the model mentioned.

Exergetic, energetic, economic and environmental evaluation of concentrated solar power plants in Libya

The PhD project addresses the potential of using concentrating solar power (CSP) plants as a viable alternative energy producing system in Libya. Exergetic, energetic, economic and environmental analyses are carried out for a particular type of CSP plants. The study, although it aims a particular type of CSP plant – 50 MW parabolic trough-CSP plant, it is sufficiently general to be applied to other configurations. The novelty of the study, in addition to modeling and analyzing the selected configuration, lies in the use of a state-of-the-art exergetic analysis combined with the Life Cycle Assessment (LCA). The modeling and simulation of the plant is carried out in chapter three and they are conducted into two parts, namely: power cycle and solar field. The computer model developed for the analysis of the plant is based on algebraic equations describing the power cycle and the solar field. The model was solved using the Engineering Equation Solver (EES) software; and is designed to define the properties at each state point of the plant and then, sequentially, to determine energy, efficiency and irreversibility for each component. The developed model has the potential of using in the preliminary design of CSPs and, in particular, for the configuration of the solar field based on existing commercial plants. Moreover, it has the ability of analyzing the energetic, economic and environmental feasibility of using CSPs in different regions of the world, which is illustrated for the Libyan region in this study. The overall feasibility scenario is completed through an hourly analysis on an annual basis in chapter Four. This analysis allows the comparison of different systems and, eventually, a particular selection, and it includes both the economic and energetic components using the “greenius” software. The analysis also examined the impact of project financing and incentives on the cost of energy. The main technological finding of this analysis is higher performance and lower levelized cost of electricity (LCE) for Libya as compared to Southern Europe (Spain). Therefore, Libya has the potential of becoming attractive for the establishment of CSPs in its territory and, in this way, to facilitate the target of several European initiatives that aim to import electricity generated by renewable sources from North African and Middle East countries. The analysis is presented a brief review of the current cost of energy and the potential of reducing the cost from parabolic trough- CSP plant. Exergetic and environmental life cycle assessment analyses are conducted for the selected plant in chapter Five; the objectives are 1) to assess the environmental impact and cost, in terms of exergy of the life cycle of the plant; 2) to find out the points of weakness in terms of irreversibility of the process; and 3) to verify whether solar power plants can reduce environmental impact and the cost of electricity generation by comparing them with fossil fuel plants, in particular, Natural Gas Combined Cycle (NGCC) plant and oil thermal power plant. The analysis also targets a thermoeconomic analysis using the specific exergy costing (SPECO) method to evaluate the level of the cost caused by exergy destruction. The main technological findings are that the most important contribution impact lies with the solar field, which reports a value of 79%; and the materials with the vi highest impact are: steel (47%), molten salt (25%) and synthetic oil (21%). The “Human Health” damage category presents the highest impact (69%) followed by the “Resource” damage category (24%). In addition, the highest exergy demand is linked to the steel (47%); and there is a considerable exergetic demand related to the molten salt and synthetic oil with values of 25% and 19%, respectively. Finally, in the comparison with fossil fuel power plants (NGCC and Oil), the CSP plant presents the lowest environmental impact, while the worst environmental performance is reported to the oil power plant followed by NGCC plant. The solar field presents the largest value of cost rate, where the boiler is a component with the highest cost rate among the power cycle components. The thermal storage allows the CSP plants to overcome solar irradiation transients, to respond to electricity demand independent of weather conditions, and to extend electricity production beyond the availability of daylight. Numerical analysis of the thermal transient response of a thermocline storage tank is carried out for the charging phase. The system of equations describing the numerical model is solved by using time-implicit and space-backward finite differences and which encoded within the Matlab environment. The analysis presented the following findings: the predictions agree well with the experiments for the time evolution of the thermocline region, particularly for the regions away from the top-inlet. The deviations observed in the near-region of the inlet are most likely due to the high-level of turbulence in this region due to the localized level of mixing resulting; a simple analytical model to take into consideration this increased turbulence level was developed and it leads to some improvement of the predictions; this approach requires practically no additional computational effort and it relates the effective thermal diffusivity to the mean effective velocity of the fluid at each particular height of the system. Altogether the study indicates that the selected parabolic trough-CSP plant has the edge over alternative competing technologies for locations where DNI is high and where land usage is not an issue, such as the shoreline of Libya.

Estudio del Secado de Anacardo (Anacardium occidentale L.) mediante Secador Solar de Radiación Directa

MACHADO, Antônio V. et al. Estudio del Secado de Anacardo (Anacardium occidentale L.) mediante Secador Solar de Radiación Directa. Información Tecnológica, v. 21, n. 1, p. 31-37, 2010.

Produção de quitosana a partir de resíduos de camarão: análise do processo e da operação de secagem

A quitina é encontrada principalmente nos exoesqueletos de crustáceos, insetos e na parede celular de fungos. O biopolímero quitosana é obtido através da hidrólise alcalina da quitina. A despolimerização da quitosana é realizada para se obter um produto com valores baixos de massa molecular. O uso da quitosana em diversas áreas é diretamente relacionada com a massa molecular e o grau de desacetilação do polímero. Os objetivos deste trabalho foram o estudo da cinética de secagem de quitina em camada delgada utilizando um modelo difusivo, considerando a resistência externa à transferência de massa; a determinação do comportamento da massa molecular média viscosimétrica da quitosana, durante a secagem convectiva, em camada delgada; a otimização das etapas de desacetilação e despolimerização da quitosana. A quitina foi obtida de resíduos de camarão. Os experimentos da secagem de quitina e da quitosana foram em secador de bandejas, a 60°C, sendo que para a quitina foram utilizadas duas velocidades do ar de 0,5 e 1,5 m/s. A estimativa da viscosidade intrínseca foi através da equação de Huggins e a massa molecular da quitosana foi calculada pela equação de Mark-Houwink-Sakurada. As otimizações da reação de desacetilação e despolimerização foram realizadas utilizando a metodologia da superfície de resposta. Para a reação de desacetilação foram variados o tempo e a temperatura. Para a reação de despolimerização foram analisados a concentração de ácido clorídrico, a temperatura e o tempo de reação. O modelo difusivo com difusividade efetiva variável, utilizado para analisar a secagem de quitina, apresentou concordância com os dados experimentais, onde foi observado o efeito da resistência externa à transferência de massa, quando utilizada a menor velocidade do ar. A condição ótima da reação de desacetilação para massa molecular foi observada na temperatura de 130°C em 90 min, e correspondeu a massa molecular de 150 kDa e um grau de desacetilação de 90%. A operação de secagem da quitosana causou um aumento na massa molecular média viscosimétrica de 27% e este aumento foi linear com o tempo e a umidade do polímero, apresentando duas regiões. As condições da reação de despolimerização para alcançar 50 kDa foram à temperatura de reação de 65°C, concentração de ácido clorídrico de 35% v/v. Nestas condições a cinética de despolimerização foi de pseudo-primeira ordem, apresentando duas fases.

Three dimensional numerical simulation of thermohaline currents of the Persian Gulf

Observational data and a three dimensional numerical model (POM) are used to investigate the Persian Gulf outflow structure and its spreading pathway into the Oman Sea. The model is based on orthogonal curvilinear coordinate system in horizontal and train following coordinate (sigma coordinate) system in vertical. In the simulation, the horizontal diffusivity coefficients are calculated form Smogorinsky diffusivity formula and the eddy vertical diffusivities are obtained from a second turbulence closure model (namely Mellor-Yamada level 2.5 model of turbulence). The modeling area includes the east of the Persian Gulf, the Oman Sea and a part of the north-east of the Indian Ocean. In the model, the horizontal grid spacing was assumed to be about 3.5 km and the number of vertical levels was set to 32. The simulations show that the mean salinity of the PG outflow does not change substantially during the year and is about 39 psu, while its temperature exhibits seasonal variations. These lead to variations in outflow density in a way that is has its maximum density in late winter (March) and its minimum in mid-summer (August). At the entrance to the Oman Sea, the PG outflow turns to the right due to Coriolis Effect and falls down on the continental slope until it gains its equilibrium depth. The highest density of the outflow during March causes it to sink more into the deeper depths in contrast to that of August which the density is the lowest one. Hence, the neutral buoyancy depths of the outflow are about 500 m and 250 m for March and August respectively. Then, the outflow spreads in its equilibrium depths in the Oman Sea in vicinity of western and southern boundaries until it approach the Ras al Hamra Cape where the water depth suddenly begins to increase. Therefore, during March, the outflow that is deeper and wider relative to August, is more affected by the steep slope topography and as a result of vortex stretching mechanism and conservation of potential vorticity it separates from the lateral boundaries and finally forms an anti-cyclonic eddy in the Oman Sea. But during August the outflow moves as before in vicinity of lateral boundaries. In addition, the interaction of the PG outflow with tide in the Strait of Hormuz leads to intermittency in outflow movement into the Oman Sea and it could be the major reason for generations of Peddy (Peddies) in the Oman Sea.

Evaluation of thermo-physical properties and drying kinetics of carrots in a convective hot air drying system

This paper presents an experimental study on the evolution of carrot properties along convective drying by hot air at different temperatures (50ºC, 60ºC and 70ºC). The thermo-physical properties calculated were: specific heat, thermal conductivity, diffusivity, enthalpy, heat and mass transfer coefficients. Furthermore, the data of drying kinetics were treated and adjusted according to the three empirical models: Page, Henderson & Pabis and Logarithmic. The sorption isotherms were also determined and fitted using the GAB model. The results showed that, generally, the thermo-physical properties presented a decline during the drying process, and the decrease was faster for the temperature of 70ºC. It was possible to verify that the Page model presented the best prediction ability for the representation of kinetics of the drying process. The GAB model used to fit the sorption isotherms showed a good prediction capacity and, at a given water activity, despite some variations, the amount of water sorbed increased with the decrease of drying temperature.

Variação da composição nutricional e propriedades de cenouras durante a secagem

Este trabalho teve como objetivo a determinação das propriedades da cenoura (Daucus carota L.), da variedade Nantes, antes, durante e após a secagem por convecção a três temperaturas diferentes (50, 60 e 70 ºC).De forma a verificar as alterações ao nível de diferentes propriedades, tais como: propriedades químicas (humidade, proteínas, fibras, cinzas, açúcares e 'aw') propriedades físicas (textura, cor, porosidade e densidade) e propriedades termofísicas (calor específico, condutividade térmica, difusividade e entalpia). Dos resultados obtidos foi possível concluir que a temperatura de secagem de 70 º C foi a que mais afetou as propriedades químicas analisadas, tais como a humidade, proteínas e açúcares redutores, onde estes sofreram uma diminuição ao longo das secagens. A 'aw' também apresentou uma diminuição ao longo das secagens, onde apresentou um menor valor na secagem a 70 ºC, tendo passado de 0,97 para 0,69, enquanto as temperaturas de 50 ºC e 60 ºC apresentaram um valor final igual, de 0,74. No que diz respeito às propriedades físicas, verificou-se que em relação à textura registaram-se evoluções semelhantes em termos de dureza, mastigabilidade e gomosidade, na medida em que sofreram uma acentuada diminuição nas primeiras horas de secagem, e a temperatura de 70 ºC foi a que mais afetou estas propriedades. No caso da cor a temperatura de 60 ºC foi a que provocou uma maior diferença de cor, a qual ao longo da secagem esta foi aumentando. A porosidade sofreu um aumento com as secagens devido à diminuição da humidade, no entanto a temperatura de 70 ºC foi a que obteve uma menor porosidade, e as temperaturas de 50 ºC e 60 ºC apresentaram valores de porosidade semelhantes. As propriedades termofísicas registaram uma diminuição ao longo da secagem, onde o calor específico sofreu uma maior diminuição com a temperatura de 70 ºC, passando de 3,90 kJ/kg.K para 1,99 kJ/kg.K. A condutividade térmica também sofreu uma maior diminuição com a temperatura de 70 ºC, diminuindo de 0,5243 W/m.K para 0,2782 W/m.K. A difusividade foi de igual forma afetada pela temperatura de 70 ºC, tendo diminuído de 1,50×10-7 m2/s para 1,06×10-7 m2/s. No caso da entalpia, esta sofreu uma maior diminuição com a temperatura de 50 ºC, passando de 233 J/kg para 96,7 J/kg. As isotérmicas de sorção foram ajustadas ao modelo de GAB, onde se verificou que apesar de algumas oscilações a quantidade de água sorvida a uma determinada aw, aumentou com a diminuição da temperatura.Os dados da cinética de secagem foram tratados e ajustados de acordo com três modelos: Page, Henderson & Pabis e Logarítmico, tendo-se verificado que o modelo de Page foi o que mostrou melhor descrever os processos em estudo, enquanto o pior modelo para descrever a cinética de secagem foi o Logarítmico.

Modifications neurométaboliques et microstructurales à la suite d'une commotion cérébrale chez les athlètes féminines

L’utilisation de méthodes d’investigation cérébrale avancées a permis de mettre en évidence la présence d’altérations à court et à long terme à la suite d’une commotion cérébrale. Plus spécifiquement, des altérations affectant l’intégrité de la matière blanche et le métabolisme cellulaire ont récemment été révélées par l’utilisation de l’imagerie du tenseur de diffusion (DTI) et la spectroscopie par résonance magnétique (SRM), respectivement. Ces atteintes cérébrales ont été observées chez des athlètes masculins quelques jours après la blessure à la tête et demeuraient détectables lorsque les athlètes étaient à nouveau évalués six mois post-commotion. En revanche, aucune étude n’a évalué les effets neurométaboliques et microstructuraux dans la phase aigüe et chronique d’une commotion cérébrale chez les athlètes féminines, malgré le fait qu’elles présentent une susceptibilité accrue de subir ce type de blessure, ainsi qu’un nombre plus élevé de symptômes post-commotionnels et un temps de réhabilitation plus long. Ainsi, les études composant le présent ouvrage visent globalement à établir le profil d’atteintes microstructurales et neurométaboliques chez des athlètes féminines par l’utilisation du DTI et de la SRM. La première étude visait à évaluer les changements neurométaboliques au sein du corps calleux chez des joueurs et joueuses de hockey au cours d’une saison universitaire. Les athlètes ayant subi une commotion cérébrale pendant la saison ont été évalués 72 heures, 2 semaines et 2 mois après la blessure à la tête en plus des évaluations pré et post-saison. Les résultats démontrent une absence de différences entre les athlètes ayant subi une commotion cérébrale et les athlètes qui n’en ont pas subie. De plus, aucune différence entre les données pré et post-saison a été observée chez les athlètes masculins alors qu’une diminution du taux de N-acetyl aspartate (NAA) n’a été mise en évidence chez les athlètes féminines, suggérant ainsi un impact des coups d’intensité sous-clinique à la tête. La deuxième étude, qui utilisait le DTI et la SRM, a révélé des atteintes chez des athlètes féminines commotionnées asymptomatiques en moyenne 18 mois post-commotion. Plus spécifiquement, la SRM a révélé une diminution du taux de myo-inositol (mI) au sein de l’hippocampe et du cortex moteur primaire (M1) alors que le DTI a mis en évidence une augmentation de la diffusivité moyenne (DM) dans plusieurs faisceaux de matière blanche. De iii plus, une approche par région d’intérêt a mis en évidence une diminution de la fraction d’anisotropie (FA) dans la partie du corps calleux projetant vers l’aire motrice primaire. Le troisième article évaluait des athlètes ayant subi une commotion cérébrale dans les jours suivant la blessure à la tête (7-10 jours) ainsi que six mois post-commotion avec la SRM. Dans la phase aigüe, des altérations neuropsychologiques combinées à un nombre significativement plus élevé de symptômes post-commotionnels et dépressifs ont été trouvés chez les athlètes féminines commotionnées, qui se résorbaient en phase chronique. En revanche, aucune différence sur le plan neurométabolique n’a été mise en évidence entre les deux groupes dans la phase aigüe. Dans la phase chronique, les athlètes commotionnées démontraient des altérations neurométaboliques au sein du cortex préfrontal dorsolatéral (CPDL) et M1, marquées par une augmentation du taux de glutamate/glutamine (Glx). De plus, une diminution du taux de NAA entre les deux temps de mesure était présente chez les athlètes contrôles. Finalement, le quatrième article documentait les atteintes microstructurales au sein de la voie corticospinale et du corps calleux six mois suivant une commotion cérébrale. Les analyses n’ont démontré aucune différence au sein de la voie corticospinale alors que des différences ont été relevées par segmentation du corps calleux selon les projections des fibres calleuses. En effet, les athlètes commotionnées présentaient une diminution de la DM et de la diffusivité radiale (DR) au sein de la région projetant vers le cortex préfrontal, un volume moindre des fibres de matière blanche dans la région projetant vers l’aire prémotrice et l’aire motrice supplémentaire, ainsi qu’une diminution de la diffusivité axiale (DA) dans la région projetant vers l’aire pariétale et temporale. En somme, les études incluses dans le présent ouvrage ont permis d’approfondir les connaissances sur les effets métaboliques et microstructuraux des commotions cérébrales et démontrent des effets délétères persistants chez des athlètes féminines. Ces données vont de pair avec la littérature scientifique qui suggère que les commotions cérébrales n’entraînent pas seulement des symptômes temporaires.

Estudo do comportamento plástico, mecânico, microestrutural e térmico do concreto produzido com resíduo de porcelanato

Population growth experienced in major cities, allied to society s need of infra-structure, especially ones related to habitational demands, increases the consumption of construction materials. As a consequence, consumption of natural resources itself. Thus, due to this process, concrete is one of the most produced materials in civil construction. This is also due to the great diversity of its application, easiness in its execution and adequate mechanical performance, as well as low production costs. Following the same tendencies in construction development, the ceramic industry has intensified the production of porcelain ceramic tiles and floors. These are achieved by a fine finishing and receive polishing at the end of the fabrication process. This work researched the use of porcelain residues in polishing for the production of concrete. All of which; due to economical and environmental issues. This process aims to prove adequate destiny for this type of residue, due to environmental issues, incorporating it to the concrete itself; all of which provides economy in consumption of the materials that constitute concrete. Thus, the main characteristics of concrete were investigated through the inclusion of different concentration of the porcelain residue as additional trait element. The residue rates incorporated to the trait varied from 10% to 50% in relation to the cement mass, in the traits with plastic additives and without plastic additives. It is observed that the inclusion of porcelain residue produced a meaningful alteration in the consistency of fresh concrete. This residue has a fine granulometry and it considerably absorbed the water used in the concrete spreading, influencing the way this material is dealt with. Thus, the value of cement striking decreases with the increase of residues present in trait. The maximal incorporation of the residue was of 50%, massively, for the same factor water/initial cement. The use of residues in concrete results in an 40% increase in the compression resistance. It is also proportional to residue concentration of porcelain in the trait. The microstructure was also favored once porosity and concrete absorption decreases with the use of this residue. The parameters demonstrate the quality and durability of the concrete produced with this residue. The use of porcelain residue in concrete composition has not produced meaningful thermal behavior changes. Thermal conductivity, heat capacity and thermal diffusivity have been maintained basically constant

Stable spike clusters for the one-dimensional Gierer-Meinhardt system

We consider the Gierer-Meinhardt system with precursor inhomogeneity in a one-dimensional interval. A spike cluster is the combination of several spikes which all approach the same point in the singular limit of small activator diffusivity. We rigorously prove the existence of a steady-state spike cluster consisting of N spikes near a non-degenerate local minimum point of the smooth inhomogeneity, where N is an arbitrary positive integer. Further, we show that this solution is linearly stable. We explicitly compute all eigenvalues, both large (of order O(1)) and small (of order o(1)). The main features of studying the Gierer-Meinhardt system in this setting are as follows: (i) it is biologically relevant since it models a hierarchical process (pattern formation of small-scale structures induced by a pre-existing large-scale inhomogeneity), (ii) it contains three different spatial scales two of which are small. (iii) all the expressions can be made explicit and often have a particularly simple form.

The bioconcentration factor of pesticides in potatoes.

We presented a model that estimates the bioconcentration factor (BCF) of pesticides in potatoes supposing that the pesticide in the soil solution is absorbed by the potato by passive diffusion, following Fick?s second law. The pesticides in the model are nonionic organic substances, traditionally used in potato crops that degrade in the soil according to a first order kinetic equation. This presents an expression that relates BCF with the pesticide elimination rate by the potato, with the pesticide accumulation rate within the potato, with the rate of growth of the potato and with the pesticide degradation rate in the soil. BCF was estimated supposing steady state equilibrium of the quotient between the pesticide concentration in the potato and the pesticide concentration in the soil solution. It is suggested that a negative correlation exists between the pesticide BCF and the soil sorption partition coefficient. The model was built based on the work of Trapp et al. (2007), [Diffusion of PAH in Potato and Carrot Slices and Applications for a Potato Model] in which an expression to calculate the diffusivity of persistent organic substances in potatoes is presented. The model consists in adding to the expression of Trapp et al. (2007) the hypothesis that the pesticide degrades in the soil. The value of BCF suggests which pesticides should be monitored in potatoes.

Relación entre atrofia cortical difusa y desempeño cognitivo : estudio en población mayor de 60 años en un hospital universitario en la ciudad de Bogotá

El presente trabajo tuvo como objetivo evaluar la existencia de la relación entre la atrofia cortical difusa objetivada por neuroimagenes cerebrales y desempeños cognitivos determinados mediante la aplicación de pruebas neuropsicológicas que evalúan memoria de trabajo, razonamiento simbólico verbal y memoria anterógrada declarativa. Participaron 114 sujetos reclutados en el Hospital Universitario Mayor Méderi de la ciudad de Bogotá mediante muestreo de conveniencia. Los resultados arrojaron diferencias significativas entre los dos grupos (pacientes con diagnóstico de atrofia cortical difusa y pacientes con neuroimagenes interpretadas como dentro de los límites normales) en todas las pruebas neuropsicológicas aplicadas. Respecto a las variables demográficas se pudo observar que el grado de escolaridad contribuye como factor neuroprotector de un posible deterioro cognitivo. Tales hallazgos son importantes para determinar protocoles tempranos de detección de posible instalación de enfermedades neurodegenerativas primarias.