Microphotoluminescence investigation of InAs quantum dot active region in 1.3 mu m vertical cavity surface emitting laser structure

Microphotoluminescence (mu-PL) investigation has been performed at room temperature on InAs quantum dot (QD) vertical cavity surface emitting laser (VCSEL) structure in order to characterize the QD epitaxial structure which was designed for 1.3 mu m wave band emission. Actual and precise QD emission spectra including distinct ground state (GS) and excited state (ES) transition peaks are obtained by an edge-excitation and edge-emission (EEEE) mu-PL configuration. Conventional photoluminescence methods for QD-VCSELs structure analysis are compared and discussed, which indicate the EEEE mu-PL is a useful tool to determine the optical features of the QD active region in an as-grown VCSEL structure. Some experimental results have been compared with simulation results obtained with the aid of the plane-wave admittance method. After adjustment of epitaxial growth according to EEEE mu-PL measurement results, QD-VCSEL structure wafer with QD GS transition wavelength of 1300 nm and lasing wavelength of 1301 nm was obtained.

Fracture of colloidal single-crystal films fabricated by controlled vertical drying deposition

Controlled vertical drying deposition method was used to make high-quality single crystal close-packed colloidal films formed of different radii polystyrene latex spheres on glass substrates coming from a low concentration water suspension (0.1% volume fraction). Regardless of the spheres radii the film thickness was about 6.3 microns. However, cracks destroyed the crystalline film structure during the colloidal film growth. The effect of particle radius (85-215 nm range) on film cracking was systematically studied using in situ optical fracture monitoring. Primary parallel cracks run along the vertical growth direction, later followed by secondary branched cracks in-between the primary cracks due to residual water evaporation. Quantitative theoretical relationship between the cracks spacing and particles radius was derived and shows good agreement with experimental observations. Normalized cracks spacing is related to a reciprocal ratio of the dimensionless particle radius.

Investigations of phase inversion and frictional pressure gradients in upward and downward oil–water flow in vertical pipes

The present study has attempted to investigate phase inversion and frictional pressure gradients during simultaneous vertical flow of oil and water two-phase through upward and downward pipes. The liquids selected were white oil (44 mPa s viscosity and 860 kg/m3 density) and water. The measurements were made for phase velocities varying from 0 to 1.24 m/s for water and from 0 to 1.87 m/s for oil, respectively. Experiments were carried either by keeping the mixture velocity constant and increasing the dispersed phase fraction or by keeping the continuous phase superficial velocity constant and increasing the dispersed phase superficial velocity. From the experimental results, it is shown that the frictional pressure gradient reaches to its lower value at the phase inversion point in this work. The points of phase inversion are always close to an input oil fraction of 0.8 for upward flow and of 0.75 for downward flow, respectively. A few models published in the literature are used to predict the phase inversion point and to compare the results with available experimental data. Suitable methods are suggested to predict the critical oil holdup at phase inversion based on the different viscosity ratio ranges. Furthermore, the frictional pressure gradient is analyzed with several suitable theoretical models according to the existing flow patterns. The analysis reveals that both the theoretical curves and the experimental data exhibit the same trend and the overall agreement of predicted values with experimental data is good, especially for a high oil fraction.

vertical growth of thalassia testudinum seasonal and interannual variability

The vertical growth of shoots of the seagrass Thalassia testudinum Banks ex Konig in four meadows, along a range of exposure to waves, in the Mexican Caribbean was examined to elucidate its magnitude and its relationship to sediment dynamics. Average internodal length varied between 0.17 and 12.75 mm, and was greatest in the meadow which experienced the greatest burial by sand waves moved by Hurricane Gilbert (September 1988). Internodal length showed annual cycles, confirmed by the flower scars always preceding or coinciding with the annual minimum internodal length. These annual cycles on the shoot allowed estimation of annual leaf production, which varied, on average, between 14.2 and 19.3 leaves per shoot year-1. High vertical shoot growth was associated with long internodes and high leaf production rate, which increased with increasing vertical shoot growth to a maximum of approximately 25 leaves per shoot year-1, with vertical growth of about 30 mm year-1 or more. Average internodal length showed substantial interannual differences from perturbations derived from the passage of Hurricane Gilbert. The growth response of the plants surviving moderate burial and erosion after the hurricane involved enhanced vertical growth and increased leaf production, and reduced vertical growth, respectively, after 1988. The variability in shoot vertical growth of T testudinum can be separated into seasonal changes in plant growth, and long-term variability associated with episodic perturbations involving sediment redistribution by hurricanes.

Vertical structure p-type permeable metal-base organic transistors based on N,N '-diphentyl-N,N '-bis(1-naphthylphenyl)-1,1 '-biphenyl-4,4 '-diamine

In this article, vertical structure p-type permeable-base organic transistors were proposed and demonstrated. A hole-type organic semiconductor N,N-'-diphentyl-N,N-'-bis(1-naphthylphenyl)-1,1(')-biphenyl-4,4(')-diamine was used as emitter and collector. In the permeable-base transistors, the metal base was formed by firstly coevaporating Al and Ca in vacuum and then annealing at 120 degrees C for 5 min in air, followed by a thin Al deposition. These devices show a common-base current gain of near 1.0 and a common-emitter current gain of similar to 270.

Vertical structure permeable-base hybrid transistors based on multilayered metal base for stable electrical characteristics

In this work we present a permeable base transistor consisting of a 60 nm thick N,N'diphenyl-N,N'-bis(1-naphthylphenyl)-1,1'-biphenyl-4,4'-diamine layer or a 40 nm thick 2,6-diphenyl-indenofluorene layer as the emitter, a CalAl/Ca multilayer as the metal base, and p-Si as collector. In the base, the Ca layers are 5 nm thick and the Al layer was varied between 10 and 40 nm. the best results obtained with a 20 nm thick layer. The devices present common-base current gain with both organic layer and silicon acting as emitter, but there is only observable common-emitter current gain when the organic semiconductor acts as emitter. The obtained common-emitter current gain, similar to 2, is independent on collector-emitter voltage, base current and organic emitter in a reasonable wide interval. Air exposure or annealing of the base is necessary to achieve these characteristics, indicating that an oxide layer is beneficial to proper device operation.

Colloidal crystal heterostructures by a two-step vertical deposition method

A two-step template-induced vertical deposition technique was introduced to fabricate the colloidal crystal heterostructures due to wettability differences and spatial confinement of the templates structured with microchannels. The heterostructures exhibited a bi-frequency Bragg diffraction whose position was determined by the microsphere diameter of the opals. It was demonstrated that the channel width had an influence on the optical properties of the colloidal crystal heterostructures. The strategy proposed is suited for fabrication of different micron-sized opal architectures with complex form and designed optical functionality.

Copper phthalocyanine based hybrid p-type permeable-base transistor in vertical architecture

We demonstrate the production of copper phthalocyanine (CuPc) based p-type hybrid permeable-base transistors, which operate at low voltages having high common-base current gains. These transistors are prepared by evaporating a thin metal layer (Ag or Al) that acts as base on top of a Si substrate that acts as collector. In the sequence CuPc and Au are thermally sublimated to produce the emitter, constituting a quite simple device production procedure with the additional advantage of allowing higher integration due to its vertical architecture.

High current density tris(8-hydroxyquinoline) aluminum-based hybrid transistor in vertical architecture

We report the construction of hybrid permeable-base transistors, in vertical architecture, using tris(8-hydroxyquinoline) aluminum as emitter, a thin gold layer as base, and n-type silicon as collector. These transistors present high common-base current gain, can be operated at low driving voltages, and allow high current density.

Study of facilitated potassium ion transfer across a water vertical bar 1,2-dichloroethane interface using different phase volume ratio systems

A study of potassium ion transfer across a water \ 1,2-dichloroethane (W \ DCE) interface facilitated by dibenzo-18-crown-6 (DB18C6) with various phase volume ratio systems is presented. The key point was that a droplet of aqueous solution containing a redox couple, Fe(CN)(6)(3-)/Fe(CN)(6)(4-), with equal molar ratio, was first attached to a platinum electrode surface, and the resulting droplet electrode was then immersed into the organic solution containing a hydrophobic electrolyte to construct a platinum electrode/aqueous phase/organic phase system. The interfacial potential of the W \ DCE within the series could be externally controlled because the specific compositions in the aqueous droplet make the Pt electrode function like a reference electrode as long as the concentration ratio of Fe(CN)(6)(3-)/Fe(CN)(6)(4-) remains constant. In this way, a conventional three-electrode potentiostat can be used to study the ion transfer process at a liquid \ liquid (L \ L) interface facilitated by an ionophore with variable phase volume ratio (r = V-o/V-w). The effect of r on ion transfer and facilitated ion transfer was studied in detail experimentally. We also demonstrated that as low as 5 x 10(-8) M DB18C6 could be determined using this method due to the effect of the high phase volume ratio.

A NOVEL DESIGN OF LIGHT-TRANSPARENT GOLD-MINIGRID THIN-LAYER FTIR SPECTROELECTROCHEMICAL CELL WITH VERTICAL CONFIGURATION

A Teflon bridge/edge-eliminator is designed to connect a glass container and a light-transparent gold-minigrid NaCl thin-layer cell to form a vertically configured in-situ FTIR spectroelectrochemical cell. The bridge/edge-eliminator sets an internal reference point for accurate potential control. The size of the thin-layer chamber is 5 X 5 X 0.11mm. A 1900-omega formal resistance of the thin-layer cell was measured in CH2Cl2/0.1 M TBAP solution. Well defined thin-layer cyclic voltammograms and IR spectral changes for ferrocene oxidation were obtained.