In situ surface topography measurement method of granite base in scanning wafer stage with laser interferometer

Topography of a granite surface has an effect on the vertical positioning of a wafer stage in a lithographic tool, when the wafer stage moves on the granite. The inaccurate measurement of the topography results in a bad leveling and focusing performance. In this paper, an in situ method to measure the topography of a granite surface with high accuracy is present. In this method, a high-order polynomial is set up to express the topography of the granite surface. Two double-frequency laser interferometers are used to measure the tilts of the wafer stage in the X- and Y-directions. From the sampling tilts information, the coefficients of the high-order polynomial can be obtained by a special algorithm. Experiment results shows that the measurement reproducibility of the method is better than 10 nm. (c) 2006 Elsevier GmbH. All rights reserved.

TRANSFER OF ANALYTICAL METHODS FOR THE CHARACTERISATION OF NATURAL PRODUCTS TO R&D PROCESSES OF IDOKI

IDOKI SCF Technologies S.L. is a technology-based company, set up on September 2006 in Derio (Biscay) with the main scope of developing extraction and purification processes based on the use of supercritical fluid extraction technology (SFE) in food processing, extraction of natural products and the production of personal care products. IDOKI¿s researchers have been working on many different R&D projects so far, most of them using this technology. However, the optimization of a SFE method for the different matrices cannot be performed unless we have an analytical method for the characterisation of the extracts obtained in each experiment. The analytical methods are also essential for the quality control of the raw materials that are going to be used and also for the final product. This PhD thesis was born to tackle this problem and therefore, it is based on the development of different analytical methods for the characterisation of the extracts and products. The projects that we could include in this thesis were the following: the extraction propolis, the recovery of agroindustrial residues (soy and wine) and the dealcoholisation of wine.On the one hand, for the extraction of propolis, several UV-Vis spectroscopic methods were used in order to measure the antioxidant capacity and the total polyphenol and flavonoid content of the extracts. A SFC method was also developed in order to measure more specific phenolic compounds. On the other hand, for the recovery of agroindustrial residues UV-Vis spectroscopy was used to determine the total polyphenol content and two SFC methods were developed to analyse different phenolic compounds. Extraction methods such as MAE, FUSE and rotary agitation were also evaluated for the characterisation of the raw materials.Finally, for the dealcoholisation of wine, the development of a SBSE-TD-GC-MS and DHS-TD-GC-MS methods for the analysis of aromas and a NIR spectroscopic method for the determination of ethanol content with the help of chemometrics was necessary. Most of these methods are typically used in IDOKI¿s lab as routine analyses apart from others not included in this PhD thesis.

Advanced Reaction Systems for Hydrogen Production

[EN] This PhD work started in March 2010 with the support of the University of the Basque Country (UPV/EHU) under the program named “Formación de Personal Investigador” at the Chemical and Environmental Engineering Department in the Faculty of Engineering of Bilbao. The major part of the Thesis work was carried out in the mentioned department, as a member of the Sustainable Process Engineering (SuPrEn) research group. In addition, this PhD Thesis includes the research work developed during a period of 6 months at the Institut für Mikrotechnik Mainz GmbH, IMM, in Germany. During the four years of the Thesis, conventional and microreactor systems were tested for several feedstocks renewable and non-renewable, gases and liquids through several reforming processes in order to produce hydrogen. For this purpose, new catalytic formulations which showed high activity, selectivity and stability were design. As a consequence, the PhD work performed allowed the publication of seven scientific articles in peer-reviewed journals. This PhD Thesis is divided into the following six chapters described below. The opportunity of this work is established on the basis of the transition period needed for moving from a petroleum based energy system to a renewable based new one. Consequently, the present global energy scenario was detailed in Chapter 1, and the role of hydrogen as a real alternative in the future energy system was justified based on several outlooks. Therefore, renewable and non-renewable hydrogen production routes were presented, explaining the corresponding benefits and drawbacks. Then, the raw materials used in this Thesis work were described and the most important issues regarding the processes and the characteristics of the catalytic formulations were explained. The introduction chapter finishes by introducing the concepts of decentralized production and process intensification with the use of microreactors. In addition, a small description of these innovative reaction systems and the benefits that entailed their use were also mentioned. In Chapter 2 the main objectives of this Thesis work are summarized. The development of advanced reaction systems for hydrogen rich mixtures production is the main objective. In addition, the use and comparison between two different reaction systems, (fixed bed reactor (FBR) and microreactor), the processing of renewable raw materials, the development of new, active, selective and stable catalytic formulations, and the optimization of the operating conditions were also established as additional partial objectives. Methane and natural gas (NG) steam reforming experimental results obtained when operated with microreactor and FBR systems are presented in Chapter 3. For these experiments nickel-based (Ni/Al2O3 and Ni/MgO) and noble metal-based (Pd/Al2O3 and Pt/Al2O3) catalysts were prepared by wet impregnation and their catalytic activity was measured at several temperatures, from 973 to 1073 K, different S/C ratios, from 1.0 to 2.0, and atmospheric pressure. The Weight Hourly Space Velocity (WHSV) was maintained constant in order to compare the catalytic activity in both reaction systems. The results obtained showed a better performance of the catalysts operating in microreactors. The Ni/MgO catalyst reached the highest hydrogen production yield at 1073 K and steam-to-carbon ratio (S/C) of 1.5 under Steam methane Reforming (SMR) conditions. In addition, this catalyst also showed good activity and stability under NG reforming at S/C=1.0 and 2.0. The Ni/Al2O3 catalyst also showed high activity and good stability and it was the catalyst reaching the highest methane conversion (72.9 %) and H2out/CH4in ratio (2.4) under SMR conditions at 1073 K and S/C=1.0. However, this catalyst suffered from deactivation when it was tested under NG reforming conditions. Regarding the activity measurements carried out with the noble metal-based catalysts in the microreactor systems, they suffered a very quick deactivation, probably because of the effects attributed to carbon deposition, which was detected by Scanning Electron Microscope (SEM). When the FBR was used no catalytic activity was measured with the catalysts under investigation, probably because they were operated at the same WHSV than the microreactors and these WHSVs were too high for FBR system. In Chapter 4 biogas reforming processes were studied. This chapter starts with an introduction explaining the properties of the biogas and the main production routes. Then, the experimental procedure carried out is detailed giving concrete information about the experimental set-up, defining the parameters measured, specifying the characteristics of the reactors used and describing the characterization techniques utilized. Each following section describes the results obtained from activity testing with the different catalysts prepared, which is subsequently summarized: Section 4.3: Biogas reforming processes using γ-Al2O3 based catalysts The activity results obtained by several Ni-based catalysts and a bimetallic Rh-Ni catalyst supported on magnesia or alumina modified with oxides like CeO2 and ZrO2 are presented in this section. In addition, an alumina-based commercial catalyst was tested in order to compare the activity results measured. Four different biogas reforming processes were studied using a FBR: dry reforming (DR), biogas steam reforming (BSR), biogas oxidative reforming (BOR) and tri-reforming (TR). For the BSR process different steam to carbon ratios (S/C) from 1.0 to 3.0, were tested. In the case of BOR process the oxygen-to-methane (O2/CH4) ratio was varied from 0.125 to 0.50. Finally, for TR processes different S/C ratios from 1.0 to 3.0, and O2/CH4 ratios of 0.25 and 0.50 were studied. Then, the catalysts which achieved high activity and stability were impregnated in a microreactor to explore the viability of process intensification. The operation with microreactors was carried out under the best experimental conditions measured in the FBR. In addition, the physicochemical characterization of the fresh and spent catalysts was carried out by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), N2 physisorption, H2 chemisorption, Temperature Programmed Reduction (TPR), SEM, X-ray Photoelectron Spectroscopy (XPS) and X-ray powder Diffraction (XRD). Operating with the FBR, conversions close to the ones predicted by thermodynamic calculations were obtained by most of the catalysts tested. The Rh-Ni/Ce-Al2O3 catalyst obtained the highest hydrogen production yield in DR. In BSR process, the Ni/Ce-Al2O3 catalyst achieved the best activity results operating at S/C=1.0. In the case of BOR process, the Ni/Ce-Zr-Al2O3 catalyst showed the highest reactants conversion values operating at O2/CH4=0.25. Finally, in the TR process the Rh-Ni/Ce-Al2O3 catalyst obtained the best results operating at S/C=1.0 and O2/CH4=0.25. Therefore, these three catalysts were selected to be coated onto microchannels in order to test its performance under BOR and TR processes conditions. Although the operation using microreactors was carried out under considerably higher WHSV, similar conversions and yields as the ones measured in FBR were measured. Furthermore, attending to other measurements like Turnover Frequency (TOF) and Hydrogen Productivity (PROD), the values calculated for the catalysts tested in microreactors were one order of magnitude higher. Thus, due to the low dispersion degree measured by H2-chemisorption, the Ni/Ce-Al2O3 catalyst reached the highest TOF and PROD values. Section 4.4: Biogas reforming processes using Zeolites L based catalysts In this section three type of L zeolites, with different morphology and size, were synthesized and used as catalyst support. Then, for each type of L zeolite three nickel monometallic and their homologous Rh-Ni bimetallic catalysts were prepared by the wetness impregnation method. These catalysts were tested using the FBR under DR process and different conditions of BSR (S/C ratio of 1.0 and 2.0), BOR (O2/CH4 ratio of 0.25 and 0.50) and TR processes (at S/C=1.0 and O2/CH4=0.25). The characterization of these catalysts was also carried out by using the same techniques mentioned in the previous section. Very high methane and carbon dioxide conversion values were measured for almost all the catalysts under investigation. The experimental results evidenced the better catalytic behavior of the bimetallic catalysts as compared to the monometallic ones. Comparing the catalysts behavior with regards to their morphology, for the BSR process the Disc catalysts were the most active ones at the lowest S/C ratio tested. On the contrary, the Cylindrical (30–60 nm) catalysts were more active under BOR conditions at O2/CH4=0.25 and TR processes. By the contrary, the Cylindrical (1–3 µm) catalysts showed the worst activity results for both processes. Section 4.5: Biogas reforming processes using Na+ and Cs+ doped Zeolites LTL based catalysts A method for the synthesis of Linde Type L (LTL) zeolite under microwave-assisted hydrothermal conditions and its behavior as a support for heterogeneously catalyzed hydrogen production is described in this section. Then, rhodium and nickel-based bimetallic catalysts were prepared in order to be tested by DR process and BOR process at O2/CH4=0.25. Moreover, the characterization of the catalysts under investigation was also carried out. Higher activities were achieved by the catalysts prepared from the non-doped zeolites, Rh-Ni/D and Rh-Ni/N, as compared to the ones supported on Na+ and Cs+ exchanged supports. However, the differences between them were not very significant. In addition, the Na+ and Cs+ incorporation affected mainly to the Disc catalysts. Comparing the results obtained by these catalysts with the ones studied in the section 4.4, in general worst results were achieved under DR conditions and almost the same results when operated under BOR conditions. In Chapter 5 the ethylene glycol (EG) as feed for syngas production by steam reforming (SR) and oxidative steam reforming (OSR) was studied by using microchannel reactors. The product composition was determined at a S/C of 4.0, reaction temperatures between 625°C and 725°C, atmospheric pressure and Volume Hourly Space Velocities (VHSV) between 100 and 300 NL/(gcath). This work was divided in two sections. The first one corresponds to the introduction of the main and most promising EG production routes. Then, the new experimental procedure is detailed and the information about the experimental set-up and the measured parameters is described. The characterization was carried out using the same techniques as for the previous chapter. Then, the next sections correspond to the catalytic activity and catalysts characterization results. Section 5.3: xRh-cm and xRh-np catalysts for ethylene glycol reforming Initially, catalysts with different rhodium loading, from 1.0 to 5.0 wt. %, and supported on α-Al2O3 were prepared by two different preparation methods (conventional impregnation and separate nanoparticle synthesis). Then, the catalysts were compared regarding their measured activity and selectivity, as well as the characterization results obtained before and after the activity tests carried out. The samples prepared by a conventional impregnation method showed generally higher activity compared to catalysts prepared from Rh nanoparticles. By-product formation of species such as acetaldehyde, ethane and ethylene was detected, regardless if oxygen was added to the feed or not. Among the catalysts tested, the 2.5Rh-cm catalyst was considered the best one. Section 5.4: 2.5Rh-cm catalyst support modification with CeO2 and La2O3 In this part of the Chapter 5, the catalyst showing the best performance in the previous section, the 2.5Rh-Al2O3 catalyst, was selected in order to be improved. Therefore, new Rh based catalysts were designed using α-Al2O3 and being modified this support with different contents of CeO2 or La2O3 oxides. All the catalysts containing additives showed complete conversion and selectivities close to the equilibrium in both SR and OSR processes. In addition, for these catalysts the concentrations measured for the C2H4, CH4, CH3CHO and C2H6 by-products were very low. Finally, the 2.5Rh-20Ce catalyst was selected according to its catalytic activity and characterization results in order to run a stability test, which lasted more than 115 hours under stable operation. The last chapter, Chapter 6, summarizes the main conclusions achieved throughout this Thesis work. Although very high reactant conversions and rich hydrogen mixtures were obtained using a fixed bed reaction system, the use of microreactors improves the key issues, heat and mass transfer limitations, through which the reforming reactions are intensified. Therefore, they seem to be a very interesting and promising alternative for process intensification and decentralized production for remote application.

Baserrietara egindako eskola bisitak: lehen hezkuntzarako material didaktikoen diseinua, ezarpena eta ebaluazioa

58 p.

Structure-change-dependent transmittance of PtOx thin film in super-resolution near-field structure: Diffraction effect analysis

To study working mechanism of super-resolution near-field structure (super-RENS) optical disk from a far-field optics view is very necessary because of the actual far-field writing/readout process in the optical disk system. A Gaussian diffraction model based on Fresnel-Kirchhoff diffraction theory of PtOx-type super-RENS has been set up in this Letter. The relationship between micro-structural deformation (change of bubble structure and refractive index profile) with far-field optical response of PtOx thin film has been studied with it in detail. The simulation results are in good agreement with the experimental results reported in literatures with a designed configuration. These results may provide more quantitative information for better understanding of the working mechanism of metal-oxide-type super-RENS. (c) 2007 Elsevier B.V. All rights reserved.

超分辨近场结构中Bubble微结构的远场光学特性分析

以菲涅尔-基尔霍夫衍射理论为基础,建立了超分辨近场结构中Bubble微结构对高斯光束的衍射模型.分析了PtOx型超分辨近场结构（PtOx-Type-Super-RENS）中Bubble微结构的远场光学特性.结果表明,设计的Bubble微结构形成过程的简化模型可基本反映超分辨近场结构中掩膜结构在激光作用下的结构变化过程,说明了高斯衍射模型是研究薄膜微结构变化的一种有效方法.

InnoSlab混合腔输出光束质量的理论研究

对InnoSlab Laser用混合腔的输出光束质量问题从热透镜效应和腔镜的不对准两个方面的影响进行理论分析,并从远场光强分布、远场发散角、光腰半径、光束质量因子M2值和桶中功率曲线等几个角度进行了讨论,特别是离轴非稳腔方向上腔镜倾斜对光束质量的影响,利用M2值和PIB曲线两个参数共同评价非稳腔的光束质量,对目前并无统一标准的非稳腔光束质量评价问题提供了有意义的参考.

Numerical and experimental analysis on green laser crystallization of amorphous silicon thin films

The effect of laser fluence on the crystallization of amorphous silicon irradiated by a frequency-doubled Nd:YAG laser is studied both theoretically and experimentally. An effective numerical model is set up to predict the melting threshold and the optimized laser fluence for the crystallization of 200-nm-thick amorphous silicon. The variation of the temperature distribution with time and the melt depth is analyzed. Besides the model, the Raman spectra of thin films treated with different fluences are measured to confirm the phase transition and to determine the optimized fluence. The calculating results accord well with those obtained from the experimental data in this research. (C) 2008 Elsevier Ltd. All rights reserved.

Simulación por elementos finitos del conformado de una pieza para carrocería de un automóvil.

[ES]El presente proyecto tiene como objetivo optimizar los parámetros de conformado a partir de la geometría de los troqueles de una pieza de un automóvil, con el fin de asegurar los parámetros de calidad que se exigen a este tipo de procesos se cumplan. Para ello, se dispone de un programa de simulación en elementos finitos cuyo nombre es Pam-Stamp 2G, en el cual se va a llevar a cabo el diseño. Además, se dispone de la matriz de la pieza requerida para una mayor facilidad de resolución. El proyecto constará de una descripción detallada del proceso de diseño del conformado durante todo el curso académico, complementado con un diagrama Gantt, así como las decisiones adoptadas durante el trabajo para lograr un desarrollo óptimo del mismo. Por último, contendrá también un presupuesto en el que se detallará los gastos que ha supuesto el desarrollo completo del trabajo.

Vulnerabilidade socioambiental dos pescadores e catadores de caranguejo da Baía de Guanabara: o trabalho e a saúde em um contexto de injustiça ambiental

O estudo tem como objetivo compreender as alterações socioambientais e econômicas que exercem grande pressão no ecossistema e que atuam diretamente na vida, trabalho e saúde dos pescadores artesanais e dessa forma promover a discussão sobre a possibilidade do fim dessa atividade artesanal na Baía de Guanabara em um contexto de vulnerabilidade e injustiça ambiental. A atividade pesqueira artesanal desenvolvida durante décadas está ameaçada de acabar principalmente por conta da degradação do ambiente e consequentemente da diminuição progressiva da pesca. Essa situação tem conseqüências sociais, econômicas e ambientais, pois são diferentes comunidades instaladas no entorno da baía que ainda sobrevivem da atividade pesqueira. O estudo tem caráter exploratório e descritivo com metodologia quanti-qualitativa, utilizando entrevistas semiestruturadas em diferentes comunidades pesqueiras da Baía de Guanabara. Foram selecionados três municípios (São Gonçalo, Itaboraí e Magé) entrevistando 100 pescadores e catadores de caranguejo que responderam a questões sobre o trabalho, a vida e a saúde. Como resultados foi possível construir indicadores socioambientais que apontam para a extrema vulnerabilidade das comunidades pesqueiras da região. É necessário que espaços de discussão sejam fortalecidos com a mobilização e atuação das comunidades pesqueiras, para busca da revitalização da baía e uma melhor qualidade de vida da população

上转换效应对Er3+-Yb3+共掺磷酸盐玻璃被动调Q 激光输出的影响

To study the effects of upconversion in Erbium, a set of rate equations that simulates the performance of the passively Q-switched Er:Yb:glass laser with a Coup>2+up>:MgAl2O4 saturable absorber was set up. The dynamics of the Erup>3+up> excited state and the effect of upconversion on the passively Q-switched laser are obtained through numerical simulation of the model. It is found that the impact ratios of upconversion effect on the peak power of the passively Q-switched laser pluse and the repetition rate are both decreased with the increase of pump power.

Metodologia de projeto de turbinas eólicas de pequeno porte.

O potencial eólico do Brasil, de vento firme e com viabilidade econômica de aproveitamento, é de 143 GW. Isso equivale ao dobro de toda a capacidade da geração já instalada no país. No Brasil, a energia eólica tem uma sazonalidade complementar à energia hidrelétrica, porque os períodos de melhor condição de vento coincidem com os de menor capacidade dos reservatórios. O projeto desenvolvido neste trabalho nasceu de uma chamada pública do FINEP, e sob os auspícios do recém criado CEPER. Ao projeto foi incorporado um caráter investigativo, de contribuição científica original, resultando em um produto de tecnologia inovadora para aerogeradores de baixa potência. Dentre os objetivos do projeto, destacamos a avaliação experimental de turbinas eólicas de 5000 W de potência. Mais especificamente, dentro do objetivo geral deste projeto estão incluídas análise estrutural, análise aerodinâmica e análise de viabilidade de novos materiais a serem empregados. Para cada uma das diferentes áreas de conhecimento que compõem o projeto, será adotada a metodologia mais adequada. Para a Análise aerodinâmica foi realizada uma simulação numérica preliminar seguida de ensaios experimentais em túnel de vento. A descrição dos procedimentos adotados é apresentada no Capítulo 3. O Capítulo 4 é dedicado aos testes elétricos. Nesta etapa, foi desenvolvido um banco de testes para obtenção das características específicas das máquinas-base, como curvas de potência, rendimento elétrico, análise e perdas mecânicas e elétricas, e aquecimento. Este capítulo termina com a análise crítica dos valores obtidos. Foram realizados testes de campo de todo o conjunto montado. Atualmente, o aerogerador de 5kW encontra-se em operação, instrumentado e equipado com sistema de aquisição de dados para consolidação dos testes de confiabilidade. Os testes de campo estão ocorrendo na cidade de Campos, RJ, e abrangeram as seguintes dimensões de análise; testes de eficiência para determinação da curva de potência, níveis de ruído e atuação de dispositivos de segurança. Os resultados esperados pelo projeto foram atingidos, consolidando o projeto de um aerogerador de 5000W.

Ninguém pode ficar parado: juventude, trabalho e projetos de vida

Este trabalho tem como objetivo estudar e discutir as maneiras pelas quais os jovens na atualidade vêm construindo trajetórias, narrativas e projetos de vida a partir das novas configurações assumidas pelo trabalho. Com a finalidade de atingir o objetivo proposto além do levantamento de referencial teórico-bibliográfico foi realizada pesquisa de campo. O referencial teórico-bibliográfico foi desenvolvido em torno das três principais categorias que envolvem o tema e dos desdobramentos delas provenientes: cenário atual, trabalho e juventude. Nessa abordagem, tanto sujeito quanto subjetividade são compreendidos como produções culturais e sociais, modos de ser e de estar no mundo que emergem dentro de contextos históricos específicos. O trabalho é entendido como uma instância privilegiada de inserção social e, portanto, como categoria que contribui de modo central para as produções de subjetividade, possuindo fundamental papel para que os jovens possam construir projetos de vida que possibilitem o desenvolvimento de trajetórias e narrativas consistentes. Pelo caráter múltiplo e heterogêneo da juventude, foi realizado um recorte desse universo para a realização do trabalho de campo, participando deste jovens entre 21 e 26 anos pertencentes à classes médias e media alta, moradores do Rio de Janeiro que exercem função de estagiários em uma empresa nacional privada localizada no mesmo Estado. Foi utilizada metodologia qualitativa para a realização da pesquisa baseada em entrevistas individuais como instrumento de coleta de dados. A análise dos resultados seguiu pressupostos teórico-metodológicos da análise de discurso. Os principais resultados mostraram que os projetos de vida dos jovens carregam em si muitas características inerentes ao contexto contemporâneo e às maneiras como o trabalho se configura: as idéias de flexibilidade, mudança, aceleração, movimento constante, abertura ao novo, entre outras. São projetos de vida múltiplos caracterizados pela mutabilidade, nos quais uma das poucas certezas que os guia é a de que ninguém pode ficar parado. As trajetórias são marcadas pelo movimento e pela lógica do cada um por si havendo um enorme comprometimento consigo mesmo. Os projetos possuem caráter individual, não sendo a eles integrados interesses coletivos. De um modo geral, pode-se observar que os projetos se mostram como tentativas de adaptação ao complexo cenário atual que parece facilitar a emergência de modos de ser e estar cada vez mais individualizados.

Desafios e práticas dos psicólogos na rede básica de saúde do município do Rio de Janeiro

O objeto do presente estudo são as práticas profissionais dos psicólogos na Saúde, em especial na atenção básica. Faz um mapeamento das atividades realizadas por essa categoria profissional na rede básica de saúde do Município do Rio de Janeiro. O estudo adota três premissas: (1) a necessidade de construção de práticas nos serviços públicos de saúde, que extrapolem a assistência psicoterápica individual (2) a inadequação da formação profissional do psicólogo para prepará-lo para atuar na rede pública de saúde e (3) o entendimento de que mudanças na formação e na prática profissionais podem ser concomitantes. O desenho da pesquisa é qualitativo e exploratório. Os métodos de pesquisa utilizados na coleta de dados foram: (1) observações; (2) entrevistas individuais com roteiros semi-estruturados e (3) questionário de caracterização profissional. O estudo teve como cenários os serviços de Psicologia da rede básica de saúde do Município do Rio de Janeiro, os Fóruns de Saúde Mental e as Supervisões de Território. Os sujeitos da pesquisa foram os gestores e os psicólogos de uma área programática (AP 5) escolhida para aprofundamento do estudo. Os dados foram analisados a partir da Análise de Conteúdo de Bardin. Estipulou-se três eixos analíticos a partir da análise do material coletado: (1) Desafios às práticas; (2) Relação formação-prática profissional e (3) Iniciativas de Educação Permanente. Os resultados evidenciam que os desafios à prática na rede básica de saúde encontram-se intrinsecamente relacionados à demanda de priorizar atendimentos à casos graves, contexto da Reforma Psiquiátrica; (2) a formação profissional do psicólogo precisa ser continuamente revista de modo a se adequar às necessidades do Sistema Único de Saúde e (3) os Fóruns de Saúde Mental e as Supervisões de Território caminham na direção das propostas de Educação Permanente, constituindo-se como espaços fundamentais para a discussão e a mudança do processo de trabalho do psicólogo na rede. Faz-se necessário a continuidade das discussões sobre a prática profissional do psicólogo na Saúde de modo a auxiliar na resolução das dificuldades encontradas no cotidiano de trabalho.

MW, Medical Watches

My project is a business plan about the set up of a company and the development of a new and innovative product aimed for the elders. I decide do this project when I discover that one of the more important needs that have the elders is to remember the medicines that they have to take. I thought that a good way could be through a smart watch. My watch have an only function, is a cheap device, easy to use, easy to understand and easy to set up, because the elders usually do not know to use complex electronics devices. There are other similar smart watches and other devices but do not have the necessary characteristics to be a good reminder for elders. My watch is centred to improve the life of the elders, but my product could also be useful for ill people who have to take many medicines during the day. After realizing this business plan, I have proved that my company is viable in the environment and profitable in the market.