Syntheses and properties of novel polyimides derived from 2-(4-aminophenyl)-5-aminopyrimidine

2-(4-Aminophenyl)-5-aminopyrimidine (4) is synthesized via a condensation reaction of vinamidium salts and amidine chloride salts, followed by hydrazine palladium catalyzed reduction. A series of novel homo- and copolyimides containing pyrimidine unit are prepared from the diamine and 1,4-phenylenediamine (PDA) with pyromellitic dianhydride (PMDA) or 3,3',4,4'-biphenyl tertracarboxylic dianhydride (BPDA) via a conventional two-step thermal imidization method. The poly(amic acid) precursors had inherent viscosities of 0.97-4.38 dL/g (c = 0.5 g/dL, in DMAc, 30 degrees C) and all of them could be cast and thermally converted into flexible and tough polyimide films. All of the polyimides showed excellent thermal stability and mechanical properties. The glass transition temperatures of the resulting polyimides are in the range of 307-434 degrees C and the 10% weight loss temperature is in the range of 556-609 degrees C under air. The polyimide films possess strength at break in the range of 185-271 MPa, elongations at break in the range of 6.8-51%, and tensile modulus in the range of 3.5-6.46 GPa. The polymer films are insoluble in common organic solvents, exhibiting high chemical resistance.

Gas permeability and permselectivity of polyimides prepared from phenylenediamines with methyl substitution at the ortho position

Polyimides were prepared from diamines: 2,4,6-trimethyl-1,3-phenylenediamine (3MPDA) and 2,3,4,5-tetramethyl-1,4-phenylenediamine (4MPDA). 1,4-Bis(3,4-dicarboxyphenoxy)benzene dianhydride (HQDPA), 3,3',4,4'-benzophenone tetracarboxylic dianhydride (BTDA), 3,3'-4,4'-diphenylsulphone tetracarboxylic dianhydride (SO(2)PDA), 3,3',4,4'-diphenylsulphide tetracarboxylic dianhydride (SPDA), pyromellitic dianhydride (PMDA), and 2,2'-bis(3,4-dicarboxyphenyl)hexa-fluoroisopropane dianhydride (6FDA) were used as dianhydride. The gas permeabilities of H-2, O-2 and N-2 through the polyimides were measured at temperatures from 30 degrees C to 90 degrees C. The results show that as methyl and trifluoromethyl substitution groups densities increase from 7.73 x 10(-3) molcm(-3) to 13.50 x 10(-3)molcm(-3), the peameability of H-2 increases 10-fold at 60% loss of permselectivity of H-2/N-2 however, the permeability of O-2 increases 20-fold at 20% loss of permselectivity of O-2/N-2. For O-2/N-2 separation, PMDA-3MPDA has similar performance to 6FDA-3MPDA and 6FDA-4MPDA; all have higher permeabilities for O-2 than normal polyimides, and the P(O-2)/alpha(O-2/N-2) trade-off relationships lie on the upper bound line for polymers. (C) 1999 Society of Chemical Industry.

Barrier properties of vinylidene chloride methyl acrylate copolymer

A series of vinylidene dichloride (VDC) copolymers with methyl acrylate (MA) as comonomer (3-12wt%), was prepared by free-radical suspension copolymerization. The permeability coefficients of the copolymers to oxygen and carbon dioxide were measured at 1.0 MPa and at 30 degrees C, and those to water vapor were measured at 30 degrees C and 100% relative humidity. All the VDC/MA copolymers studied are semicrystalline. As the MA content increases, the permeability coefficients of the copolymers to oxygen, carbon dioxide, and water vapor are progressively increased, caused by decrease in crystalline fraction and increase in free volume of VDC/MA copolymers.

Barrier property and structure of acrylonitrile/acrylic copolymers

A series of acrylonitrile (AN) copolymers with methyl acrylate (MA) or ethyl acrylate (EA) as comonomer (5-23 wt%) was prepared by free-radical copolymerisation. The permeability coefficients of the copolymers to oxygen and carbon dioxide were measured at 1.0 MPa and at 30 degrees C, and those to water vapor also measured at 100% relative humidity and at 30 degrees C. All the AN/acrylic copolymers are semicrystalline. As the acrylate content increase, the permeability coefficients of the copolymers to oxygen and carbon dioxide are increased progressively, but those to water vapor are decreased progressively. The gas permeability coefficients of the polymers were correlated with free-volume fractions or the ratio of free volume to cohesive energy.

Crystallization behaviour of poly(ether ether ketone)/poly(ether sulfone) block copolymer

The crystallization and melting behaviours of a multiblock copolymer comprising poly(ether ether ketone) (PEEK) and poly(ether sulfone) (PES) blocks whose number average molecular weights <((M)over bar (n)'s)> were 10 000 and 2900, respectively, were studied. The effect of thermal history on crystallization was investigated by wide-angle X-ray diffraction measurement. A differential scanning calorimeter was used to detect the thermal transitions and to monitor the energy evolved during the isothermal crystallization process from the melt. The results suggest that the crystallization of the copolymer becomes more difficult as compared with that of pure PEEK. The equilibrium melting point of the copolymer was found to be 357 degrees C, about 30 degrees C lower than that of pure PEEK. During the isothermal crystallization, relative crystallinity increased with crystallization time, following an Avrami equation with exponent n approximate to 2. The fold surface free energy for the copolymer crystallized from the melt was calculated to be 73 erg cm(-2), about 24 erg cm(-2) higher than that of pure PEEK. Copyright (C) 1996 Elsevier Science Ltd.

Barrier properties of vinylidene chloride copolymers

The permeability coefficients of a series of copolymers of vinylidene chloride (VDC) with methyl acrylate (MA), butyl acrylate (BA) or vinyl chloride (VC) (as comonomer) to oxygen and carbon dioxide have been measured at 1.0 MPa and 30 degrees C, while those to water vapor have been measured at 30 degrees C and 100% relative humidity. All the copolymers are semicrystalline. VDC/MA copolymers have lower melting temperature compared with VDC/BA copolymers, while that melting temperature of VDC/VC copolymer is higher than that of VDC/acrylate copolymers with the same VDC content. The barrier property of the copolymers is predominantly controlled by crystallite, free volume fraction, and cohesive energy. The permeability coefficients of VDC/MA copolymers to oxygen, carbon dioxide, and water vapor were successfully correlated with the ratio of free volume to cohesive energy.

GAS PERMEABILITIES AND PERMSELECTIVITY OF PHOTOCHEMICALLY CROSS-LINKED POLYIMIDES

Photosensitive polyimide BTDA-3MPDA was modified by UV irradiation. The structure of UV-irradiated polyimides was investigated by FTIR and gel fraction measurements. The results showed that longer UV exposure time resulted in a higher extent of crosslinking. The gas permeabilities of hydrogen, oxygen and nitrogen through UV-irradiated polyimides were characterized in a temperature range from 30 degrees C to 90 degrees C. Photocrosslinking resulted in a sharp decline in gas permeability for hydrogen, oxygen, and nitrogen through polyimide in the initial stage of photocrosslinking. Then, as the crosslinked benzophenone percentage amounted to 28-38% for hydrogen, 17-31% for oxygen and 3-28% for nitrogen, the gas permeabilities showed another sharp decline. Gas permselectivity increased significantly with the progress of photocrosslinking, and it can be adjusted in a wide range by controlling the extent of crosslinking. Arrhenius plots of gas permeability for hydrogen and oxygen through UV-irradiated polyimides are straight lines; for nitrogen, however, change in the slope of the straight line is observed and activation energies for hydrogen and oxygen permeation show abrupt increases when crosslinked benzophenone percentage amounts to about 30%. UV-irradiated polyimides with simultaneous high gas permeability and permselectivity make them ideal candidate materials for gas separation. (C) 1995 John Wiley & Sons, Inc.

STUDIES ON THE SULFONATION OF POLY(PHENYLENE OXIDE) (PPO) AND PERMEATION BEHAVIOR OF GASES AND WATER-VAPOR THROUGH SULFONATED PPO MEMBRANES .3. SORPTION BEHAVIOR OF WATER-VAPOR IN PPO AND SULFONATED PPO MEMBRANES

Water vapor absorption and desorption by poly (phenylene oxide) (PPO) and sulfonated PPO (SPPO) membranes were studied at a constant temperature of 30-degrees-C and over a broad range of water activity (0.05 less-than-or-equal-to a < 0.8) by the weighing

DETERMINATION OF THE MARK-HOUWINK EQUATION FOR CHITOSANS WITH DIFFERENT DEGREES OF DEACETYLATION

The values of k and alpha in the Mark-Houwink equation have been determined for chitosans with different degrees of deacetylation (DD) (69, 84, 91 and 100% respectively), in 0.2 M CH3COOH/0.1 M CH3COONa aqueous solution at 30-degrees-C by the light scattering method. It was shown that the values of alpha-decreased from 1.12 to 0.81 and the values of k increased from 0.104 x 10(-3) to 16.80 x 10(-3) ml/g, when the DD varied from 69 to 100%. This is due to a reduction of rigidity of the molecular chain and an increase of the electrostatic repulsion force of the ionic groups along the polyelectrolyte chain in chitosan solution, when the DD of chitosan increases gradually.

CRYSTALLIZATION OF POLY(ARYL-ETHER-ETHER-KETONE)S BLENDS

The crystallization and melting behaviour of poly(aryl-ether-ether-ketone) (PEEK) in blends with another polymer of the same family containing a bulky pendant phenolphthalein group (PEK-C) have been investigated by thermal methods. The small interaction energy density of the polymer pair (B = -8.99 J/cm3), evaluated from equilibrium melting point depression, is consistent with the T(g) data that indicate partial miscibility in the melt. Two conjugated phases are in equilibrium at 430-degrees-C: one is crystallizable and contains about 35 wt% of PEK-C; the other, containing only 15 wt% of PEEK, does not form crystals upon cooling and it interferes with the development of spherulites in the sample. The analysis of kinetic data according to nucleation theories shows that crystallization of PEEK in the explored temperature range takes place in Regime III and that a transition to Regime II might be a consequence of an increase in the amount of non-crystallizable molecules in the PEEK-rich phase. A composition independent value of the end surface free energy of PEEK lamellae has been derived from kinetic data (sigma-e = 40 +/- 4 erg/cm2) in excellent agreement with previous thermodynamic estimates. A new value for the equilibrium melting temperature of PEEK (T(m)-degrees = 639 K) has been obtained; it is about 30-degrees-C lower than the commonly accepted value and it explains better the "memory effect" in the crystallization from the melt of this high performance polymer.

COMPARISON OF THE BEHAVIOR OF CYCLIC AND LINEAR POLYSTYRENE IN DILUTE-SOLUTION

Using a low angle laser light scattering photometer, the second virial coefficients (A2) of both cyclic and linear polystyrene were determined in cyclohexane, toluene and methyl ethyl ketone (MEK) solutions. From the data obtained in cyclohexane solution the theta-temperature of cyclic polystyrene was determined to be 30-degrees-C. In toluene solution A2 of cyclic polystyrene is smaller than that of linear polystyrene with the same molecular weight, but in MEK the values are similar.

氯磺化聚乙烯的γ-辐射交联

氯磺化聚乙烯(简称CSM)由于存在SO_2Cl基团很容易通过金属氧化物进行化学交联,但至今未见其辐射交联的详细报道.本文探讨氯含量对CSM辐射交联的影响. 所用CSM系吉林化工公司产品:20型(含氯量29～33％,下同),40型(33～37％)和30型(40～45％).将CSM和防老D按一定比例混炼均匀,再在140℃左右热压成形.试样用3.33×10~(15)Bg ~(60)Co于室温限量空气下进行辐照.辐照过的试样于80℃处理2小时以消除俘陷自由基.在氮气保护下先后用二甲苯和无水乙醇,加热回流48小时和8小时,测定凝胶含量.

SOME ASPECTS OF THE GROWTH OF GRACILARIA-TENUISITIPITATA IN POND CULTURE

The effect of temperature, salinity, nitrogen, culture density and depth on the growth of Gracilaria tenuistipitata were investigated between April 1985 and March 1986 in outdoor ponds in Guangxi Province, South China. The mean annual growth rate was 2.4% per day. Under favourable temperatures of 20-30-degrees-C, daily growth rate may reach as high as 3.3%. Salinity had an obvious effect on growth and photosynthesis and growth peaked at 21 parts per thousand, with a broad plateau between 7-27 parts per thousand. Growth experiments showed that a total nitrogen (NH4-N plus NO3-N) concentration of 4 muM was sufficient to enable the plants to maintain a daily growth rate of 2.7%. The best growth of the plant was obtained at a culture density of 0.5-1 kg M-2 and a culture depth of 30 cm in the pond.

Temperature and light tolerance of representative brown, green and red algae in tumble culture revealed by chlorophyll fluorescence measurements

Laminaria japonica, Undaria pinnatifida, Ulva lactuca, Grateloupia turuturu and Palmaria palmata are Suitable species that fit the requirements of a seaweed-animal integrated aquaculture system in terms of their viable biomass, rapid growth and promising nutrient uptake rates. fit this investigation, the responses of the optimal chlorophyll fluorescence yield of the five algal species in tumble Culture were assessed at a temperature range of 10 similar to 30 degrees C. The results revealed that Ulva lactuca was the most resistant species to high temperature, withstanding 30 degrees C for 4 h without apparent decline in the optimal chlorophyll fluorescence yield. While the arctic alga Palmaria palmata was the most vulnerable one, showing significant decline in the optimal chlorophyll fluorescence yield at 25 degrees C for 2 h. The cold-water species Laminaria japonica, however, demonstrated strong ability to cope with higher temperature (24 similar to 26 degrees C) for shorter time (within 24 h) without significant decline in the optimal chlorophyll fluorescence yield. Grateloupia turuturu showed a general decrease in the optimal chlorophyll fluorescence yield with the rising temperature from 23 to 30 degrees C, similar to the temperate kelp Undaria pinnatifida. Changes of chlorophyll fluorescence yields of these algae were characterized differently indicating the existence of species-unique strategy to cope with high light. Measurements of the optimal chlorophyll fluorescence yield after short exposure to direct solar irradiance revealed how long these exposures could be without significant photoinhibition or with promising recovery in photosynthetic activities. Seasonal pattern of alternation of algal species in tank culture in the Northern Hemisphere at the latitude of 36 degrees N was proposed according to these basic measurements.

Fermentative hydrogen production by the new marine Pantoea agglomerans isolated from the mangrove sludge

A new fermentative hydrogen-producing bacterium was isolated from mangrove sludge and identified as Pantoea agglomerans using light microscopic examination, Biolog test and 16S rRNA gene sequence analysis. The isolated bacterium, designated as P. agglomerans BH-18, is a new strain that has never been optimized as a potential hydrogen-producing bacterium. In this study, the culture conditions and the hydrogen-producing ability of P. agglomerans BH-18 were examined. The strain was a salt-tolerant facultative anaerobe with the initial optimum pH value at 8.0-9.0 and temperature at 30 degrees C on cell growth. During fermentation, hydrogen started to evolve when cell growth entered late-exponential phase and was mainly produced in the stationary phase. The strain was able to produce hydrogen over a wide range of initial pH from 5 to 10, with an optimum initial pH of 6. The level of hydrogen production was affected by the initial glucose concentration, and the optimum value was found to be 10 g glucose/l. The maximum hydrogen-producing yield (2246 ml/l) and overall hydrogen production rate (160 ml/l/h) were obtained at an initial glucose concentration of 10 g/l and an initial pH value of 7.2 in marine culture conditions. In particular, the level of hydrogen production was also affected by the salt concentration. Hydrogen production reached a higher level in fresh culture conditions than in marine ones. In marine conditions, hydrogen productivity was 108 ml/l/h at an initial glucose concentration of 20 g/l and pH value of 7.2, whereas, it increased by 27% in fresh conditions. In addition, this strain could produce hydrogen using glucose and many other carbon sources such as fructose, sucrose, sorbitol and so on. As a result, it is possible that P. agglomerans BH-18 is used for biohydrogen production and biological treatment of mariculture wastewater and marine organic waste. (C) 2008 International Association for Hydrogen Energy. Published by Elsevier Ltd. All rights reserved.