XWiki Mobile: architetture collaborative per device mobili

Studio di una interfaccia mobile web per la piattaforma XWiki.

Control of the long-range self-organization of polycyclic aromatic hydrocarbons for device applications

Electronic devices based on organic semiconductors have gained increased attention in nanotechnology, especially applicable to the field of field-effect transistors and photovoltaic. A promising class of materials in this reseach field are polycyclic aromatic hydrocarbons (PAHs). Alkyl substitution of these graphenes results in the selforganization into one-dimensional columnar superstructures and provides solubility and processibility. The nano-phase separation between the π-stacking aromatic cores and the disordered peripheral alkyl chains leads to the formation of thermotropic mesophases. Hexa-peri-hexabenzocoronenes (HBC), as an example for a PAH, exhibits some of the highest values for the charge carrier mobility for mesogens, which makes them promising candidates for electronic devices. Prerequisites for efficient charge carrier transport between electrodes are a high purity of the material to reduce possible trapping sites for charge carriers and a pronounced and defect-free, long-range order. Appropriate processing techniques are required to induce a high degree of aligned structures in the discotic material over macroscopic dimensions. Highly-ordered supramolecular structures of different discotics, in particular, of HBC derivatives have been obtained by solution processing using the zone-casting technique, zone-melting or simple extrusion. Simplicity and fabrication of highly oriented columnar structures over long-range are the most essential advantages of these zone-processing methods. A close relation between the molecular design, self-aggregation and the processing conditions has been revealed. The long-range order achieved by the zone-casting proved to be suitable for field effect transistors (FET).

Experimental analysis of a separation control device based on plasma technology

In this thesis effects of plasma actuators based on Dielectric Barrier Discharge (DBD) technology over a NACA 0015 bidimensional airfoil have been analyzed in an experimental way, at low Reynolds number. Work developed on thesis has been carried on in partnership with the Department of Electrical Engineering of Università di Bologna, inside Wind Tunnel of the Applied Aerodynamic Laboratory of Aerospace Engineering faculty. In order to verify the effectiveness of these active control devices, the analysis has shown how actuators succeed in prevent boundary layer separation only in certain conditions af angle of attack and Reynolds numbers. Moreover, in this thesis actuators’ chordwise position effect has been also analyzed, together with the influence of steady and unsteady operations.

Modeling systems and vis/NIR device to improve peach and nectarine pre and post-harvest fruit maturity management

During the last decade peach and nectarine fruit have lost considerable market share, due to increased consumer dissatisfaction with quality at retail markets. This is mainly due to harvesting of too immature fruit and high ripening heterogeneity. The main problem is that the traditional used maturity indexes are not able to objectively detect fruit maturity stage, neither the variability present in the field, leading to a difficult post-harvest management of the product and to high fruit losses. To assess more precisely the fruit ripening other techniques and devices can be used. Recently, a new non-destructive maturity index, based on the vis-NIR technology, the Index of Absorbance Difference (IAD), that correlates with fruit degreening and ethylene production, was introduced and the IAD was used to study peach and nectarine fruit ripening from the “field to the fork”. In order to choose the best techniques to improve fruit quality, a detailed description of the tree structure, of fruit distribution and ripening evolution on the tree was faced. More in details, an architectural model (PlantToon®) was used to design the tree structure and the IAD was applied to characterize the maturity stage of each fruit. Their combined use provided an objective and precise evaluation of the fruit ripening variability, related to different training systems, crop load, fruit exposure and internal temperature. Based on simple field assessment of fruit maturity (as IAD) and growth, a model for an early prediction of harvest date and yield, was developed and validated. The relationship between the non-destructive maturity IAD, and the fruit shelf-life, was also confirmed. Finally the obtained results were validated by consumer test: the fruit sorted in different maturity classes obtained a different consumer acceptance. The improved knowledge, leaded to an innovative management of peach and nectarine fruit, from “field to market”.

Approccio combinato geo-location database e sensing per individuare i livelli di potenza trasmissibili da white space device

La Cognitive Radio è un dispositivo in grado di reagire ai cambiamenti dell’ambiente radio in cui opera, modificando autonomamente e dinamicamente i propri parametri funzionali tra cui la frequenza, la potenza di trasmissione e la modulazione. Il principio di base di questi dispositivi è l’accesso dinamico alle risorse radio potenzialmente non utilizzate, con cui utenti non in possesso di licenze possono sfruttare le frequenze che in un determinato spazio temporale non vengono usate, preoccupandosi di non interferire con gli utenti che hanno privilegi su quella parte di spettro. Devono quindi essere individuati i cosiddetti “spectrum holes” o “white spaces”, parti di spettro assegnate ma non utilizzate, dai quali prendono il nome i dispositivi.Uno dei modi per individuare gli “Spectrum holes” per una Cognitive Radio consiste nel cercare di captare il segnale destinato agli utenti primari; questa tecnica è nota con il nome di Spectrum Sensing e consente di ottenere essenzialmente una misura all’interno del canale considerato al fine di determinare la presenza o meno di un servizio protetto. La tecnica di sensing impiegata da un WSD che opera autonomamente non è però molto efficiente in quanto non garantisce una buona protezione ai ricevitori DTT che usano lo stesso canale sul quale il WSD intende trasmettere.A livello europeo la soluzione che è stata ritenuta più affidabile per evitare le interferenze sui ricevitori DTT è rappresentata dall’uso di un geo-location database che opera in collaborazione con il dispositivo cognitivo.Lo scopo di questa tesi è quello di presentare un algoritmo che permette di combinare i due approcci di geo-location database e Sensing per definire i livelli di potenza trasmissibile da un WSD.

Experimental and Numerical Analysis of Gas Forced Convection through Microtubes and Micro Heat Exchangers

The last decade has witnessed very fast development in microfabrication technologies. The increasing industrial applications of microfluidic systems call for more intensive and systematic knowledge on this newly emerging field. Especially for gaseous flow and heat transfer at microscale, the applicability of conventional theories developed at macro scale is not yet completely validated; this is mainly due to scarce experimental data available in literature for gas flows. The objective of this thesis is to investigate these unclear elements by analyzing forced convection for gaseous flows through microtubes and micro heat exchangers. Experimental tests have been performed with microtubes having various inner diameters, namely 750 m, 510 m and 170 m, over a wide range of Reynolds number covering the laminar region, the transitional zone and also the onset region of the turbulent regime. The results show that conventional theory is able to predict the flow friction factor when flow compressibility does not appear and the effect of fluid temperature-dependent properties is insignificant. A double-layered microchannel heat exchanger has been designed in order to study experimentally the efficiency of a gas-to-gas micro heat exchanger. This microdevice contains 133 parallel microchannels machined into polished PEEK plates for both the hot side and the cold side. The microchannels are 200 µm high, 200 µm wide and 39.8 mm long. The design of the micro device has been made in order to be able to test different materials as partition foil with flexible thickness. Experimental tests have been carried out for five different partition foils, with various mass flow rates and flow configurations. The experimental results indicate that the thermal performance of the countercurrent and cross flow micro heat exchanger can be strongly influenced by axial conduction in the partition foil separating the hot gas flow and cold gas flow.

Porting monitor di rete per gestione interfacce su device android.

Il lavoro svolto in questa tesi consiste nell'effettuare il porting del Monitor di rete da Linux ad Android,facente parte di un sistema più complesso conosciuto come ABPS. Il ruolo del monitor è quello di configurare dinamicamente tutte le interfacce di rete disponibili sul dispositivo sul quale lavora,in modo da essere connessi sempre alla miglior rete conosciuta,ad esempio al miglior Access Point nel caso del interfaccia wireless.

Development and characterization of micromachined devices for separation techniques

Nowadays microfluidic is becoming an important technology in many chemical and biological processes and analysis applications. The potential to replace large-scale conventional laboratory instrumentation with miniaturized and self-contained systems, (called lab-on-a-chip (LOC) or point-of-care-testing (POCT)), offers a variety of advantages such as low reagent consumption, faster analysis speeds, and the capability of operating in a massively parallel scale in order to achieve high-throughput. Micro-electro-mechanical-systems (MEMS) technologies enable both the fabrication of miniaturized system and the possibility of developing compact and portable systems. The work described in this dissertation is towards the development of micromachined separation devices for both high-speed gas chromatography (HSGC) and gravitational field-flow fractionation (GrFFF) using MEMS technologies. Concerning the HSGC, a complete platform of three MEMS-based GC core components (injector, separation column and detector) is designed, fabricated and characterized. The microinjector consists of a set of pneumatically driven microvalves, based on a polymeric actuating membrane. Experimental results demonstrate that the microinjector is able to guarantee low dead volumes, fast actuation time, a wide operating temperature range and high chemical inertness. The microcolumn consists of an all-silicon microcolumn having a nearly circular cross-section channel. The extensive characterization has produced separation performances very close to the theoretical ideal expectations. A thermal conductivity detector (TCD) is chosen as most proper detector to be miniaturized since the volume reduction of the detector chamber results in increased mass and reduced dead volumes. The microTDC shows a good sensitivity and a very wide dynamic range. Finally a feasibility study for miniaturizing a channel suited for GrFFF is performed. The proposed GrFFF microchannel is at early stage of development, but represents a first step for the realization of a highly portable and potentially low-cost POCT device for biomedical applications.

La normativa tecnica sul software medical device: analisi del rischio ed impatto sulle aziende sanitarie

Quadro normativo sui Dispositivi Medici e la sua evoluzione (2007/47,UNI CEI EN ISO 14971). Software DM: processo di certificazione,gestione di reti IT medicali, ruoli e responsabilità (CEI 80001-1). Casi d'uso: Linee guida: MEDDEV e linee guida svedesi più relativi esempi applicabili alle aziende sanitarie.

Analisi del fenomeno bring your own device: La nuova sfida per affrontare la mobilita lavorativa analizzata all?interno di una multinazionale farmaceutica.

Imprese di piccole e grandi dimensioni hanno dovuto convivere con il ritmo di uscita di nuovi e più potenti modelli di PC, consolle per videogiochi, telefoni cellulari, tablet, fotocamere digitali. I cicli di vita si sono ridotti drasticamente, tanto da far sembrare un’emergenza il rilascio di un nuovo prodotto quasi ogni anno. Le aziende, se ancora non lo hanno fatto, sono chiamate ad affrontare una transizione interna per aggiornare le politiche aziendali in modo da stare al passo con il progresso tecnologico. Se un tempo le regole interne vietavano o scoraggiavano l’utilizzo di dispositivi personali nell’ambiente di lavoro, nell’era moderna sono costrette ad accettarlo se non addirittura ad incoraggiarlo ed il fenomeno che mi accingerò ad analizzare in questo elaborato, denominato Bring Your Own Device (BYOD), punta proprio all’esplorazione degli sforzi progettuali che sono richiesti ad una grande azienda multinazionale per poter recepire i trend informatici. Con più di cinque miliardi di dispositivi mobili in tutto il mondo – e solo 2 miliardi di computer – il passaggio al ‘mobile’ come forma principale di collegamento alle reti aziendali procede con sempre maggiore rapidità. Negli anni recenti si è potuto assistere all’evoluzione del panorama di dispositivi portatili che ha permesso ad un pubblico di users sempre più vasto di potersi permettere l’acquisto di dispositivi di ultima generazione a prezzi non proibitivi. I fornitori di tecnologie hanno confezionato prodotti sempre più pensati per un uso privato, fornendo un’ampia scelta di soluzioni non solo a livello enterprise, come accadeva agli albori del boom tecnologico, ma maggiormente rivolte al singolo consumatore. Guardando ai trend sviluppatisi negli anni recenti, è possibile riconoscere una scia di segnali che preannunciavano quanto sta avvenendo adesso con il BYOD.

Liquid crystalline cellulose derivatives for mirrorless lasing

In this thesis cholesteric films made of liquid crystalline cellulose derivatives with improved optical properties were prepared. The choice of the solvent, hydrogen bond influencing additives, the synthetic realization of a very high degree of substitution on the cellulosic polymer and the use of mechanical stirring at the upper concentration limit of the liquid crystalline range were the basis for an improved alignment of the applied cellulose tricarbamates. In combination with a tuned substrate treatment and film preparation method, cholesteric films were obtained, with optical properties that were theoretically predicted and only known from low molecular weight liquid crystals so far. Subsequent polymerization allowed a permanent fixing of the alignment and the fabrication of free standing and insensitive films.rnThe incorporation of inorganic nanorods into the cholesteric host material was mediated with tailored block copolymers, available via controlled radical polymerization methods. In addition to the shape match between the rodlike mesogens of the host and the nanorods it was possible to increase the miscibility of both materials. Nevertheless, the size of the nanorods, in comparison to the mesogens, in these densely packed liquid crystalline phases as well as their long equilibration times were the reasons for phase separation. Nanorods are, in principle, valuable substitutes for organics, but their utilization in cellulosic CLC was not to be combined with a high quality alignment of the cholesteric structure.rnA swelling process of polymerized films in a dye solution or dissolving dyes in non-polymerized CLC was used for incorporation of the organic chromophores. With the first method the CLC could be aligned and polymerized without any disturbance due to dye molecules. The optical properties of dye and CLC were matched, with regard to mirrorless lasing devices. The dye was optically excited and laser emission supported by the cholesteric cavity was obtained. The polarization and wavelength of the emitted radiation as well as its bandwidth, the obtained interference pattern and threshold behavior of the emission proofed the feedback mechanism that was not believed to be realizable in liquid crystalline polymers. rnUtilization of a microfluidic co-flow injection device enabled us to transfer the properties of cellulosic CLC from the planar film shape to spherical micrometer sized particles. The pure material yielded particles with distorted mesogen alignment similar to films prepared by capillary flow. Dilution of the CLC with a solvent that migrated into the carrier phase during particle preparation provided the basis for particles with well ordered areas. rnAlthough cellulose derivatives were known for their liquid crystalline behavior for decades and synthesized in mass production, their application as feedback material was affected by bad optical properties. In comparison to low molar mass compounds, the low degree of order in the CLC phase was the cause. With the improved material, defined lasing emission was shown and characterized. Derivatives of cellulose are desirable materials, because, as a renewable resource, they are available in large amounts for a low price and need only simple derivatization reactions. The fabrication of CLC films with tunable lasing emission, for which this thesis can provide a starting point, is in good agreement with today's requirements of modern technology and its miniaturization.rn

Control over microstructure evolution and device performance in solution processable organic field-effect transistors

Die Arbeit beschäftigt sich mit der Kontrolle von Selbstorganisation und Mikrostruktur von organischen Halbleitern und deren Einsatz in OFETs. In Kapiteln 3, 4 und 5 eine neue Lösungsmittel-basierte Verabeitungsmethode, genannt als Lösungsmitteldampfdiffusion, ist konzipiert, um die Selbstorganisation von Halbleitermolekülen auf der Oberfläche zu steuern. Diese Methode als wirkungsvolles Werkzeug erlaubt eine genaue Kontrolle über die Mikrostruktur, wie in Kapitel 3 am Beispiel einer D-A Dyad bestehend aus Hexa-peri-hexabenzocoronene (HBC) als Donor und Perylene Diimide (PDI) als Akzeptor beweisen. Die Kombination aus Oberflächenmodifikation und Lösungsmitteldampf kann die Entnetzungseffekte ausgleichen, so dass die gewüschte Mikrostruktur und molekulare Organisation auf der Oberfläche erreicht werden kann. In Kapiteln 4 und 5 wurde diese Methode eingesetzt, um die Selbstorganisation von Dithieno[2, 3-d;2’, 3’-d’] benzo[1,2-b;4,5-b’]dithiophene (DTBDT) und Cyclopentadithiophene -benzothiadiazole copolymer (CDT-BTZ) Copolymer zu steuern. Die Ergebnisse könnten weitere Studien stimulieren und werfen Licht aus andere leistungsfaähige konjugierte Polymere. rnIn Kapiteln 6 und 7 Monolagen und deren anschlieβende Mikrostruktur von zwei konjugierten Polymeren, Poly (2,5-bis(3-alkylthiophen-2-yl)thieno[3,2-b]thiophene) PBTTT und Poly{[N,N ′-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis (dicarboximide)-2,6-diyl]-alt-5,5′- (2,2′-bithiophene)}, P(NDI2OD-T2)) wurden auf steife Oberflächen mittels Tauchbeschichtung aufgebracht. Da sist das erste Mal, dass es gelungen ist, Polymer Monolagen aus der Lösung aufzubringen. Dieser Ansatz kann weiter auf eine breite Reihe von anderen konjugierten Polymeren ausgeweitet werden.rnIn Kapitel 8 wurden PDI-CN2 Filme erfolgreich von Monolagen zu Bi- und Tri-Schichten auf Oberflächen aufgebracht, die unterschiedliche Rauigkeiten besitzen. Für das erste Mal, wurde der Einfluss der Rauigkeit auf Lösungsmittel-verarbeitete dünne Schichten klar beschrieben.rn

Progettazione ed implementazione di un prototipo per la geolocalizzazione indoor dei device wifi in ambito aeroportuale.

Nel documento vengono trattate le principali tecniche di geolocalizzazione basate sull'elaborazione dei segnali elettromagnetici ricevuti. E' altresì introdotto un sistema di remote positioning basato su test di prossimità rafforzato tramite machine learning tramite un approccio simulativo ed una implementazione reale.

Comunicazione device-to-device attraverso tecnologia WiFi-Direct: una valutazione sperimentale

Tesi di Laurea relativa allo studio della tecnologia Wi-Fi Direct in ambito Android attraverso test specifici.