Kannettavan kaasuilmaisimen suunnittelu ja toteutus

Työn tarkoituksena on suunnitella ja toteuttaa kannettava kaasuilmaisin, joka soveltuu erityisesti tavallisen kuluttajan tarpeisiin. Kaasuilmaisin on herkkä haihtuville palaville kaasuille, sekä orgaanisille kaasuille. Työssä käytetään Atmelin ATMega164P- mikrokontrolleria, piirin ohjelmointiin käytetään AVR-ISP-II, ja kehitystyökaluina AVRStudio 4:ää. Piirilevy on suunniteltu Cadsoftin Eagle- piirieditorilla. Työssä käydään läpi kokonaisvaltainen sulautetun järjestelmän suunnitteluprosessi, tuotteen spesifikaatioiden määrityksistä aina valmiin fyysisen tuotteen valmistuttamiseen asti. Tuote suunnitellaan Environics Oy:lle.

Enhancement of water removal in the press section

The effectiveness of water removal on press section is very important for a paper and board machine’s functioning, efficiency and economy. Today, the most effective method for wet pressing is shoe press technology. Metso has carried out a number of studies concerning anew type of water removal method for a press section, which has also been patented. These studies include rough sketches and some test runs. These issues form the basis of this thesis. The objective of this work was to gather together information for a new and enhanced waterremoval method for a press section by studying the functioning of the device andcarrying out test runs. This method is referred to here as Hydronip. The main goal was tobuild a functional test site which fulfills all the necessary requirements and has all thenecessary information gathering devices. The design process was carried out by emphasizing the safety aspects. The goal was also to gather together information about the nip structure in running conditions, the seal function, and to carry out the nip tests with paper or board wads. This thesis consists of a theory part, the design and construction of the test site, and carrying out test runs through information gathering. The theory part consists of the principals of water removal from a press section, Hydronip construction, and the requirements for the test place. The safety aspects were taken into account especially in test runs, but also in the assembly stages. The design and construction of the test site includes the selection of equipment and surroundings that are needed for managing the test runs in the best possible way at certain premises. The test site included the equipment that was already on the premises. Some equipment could be used as it was but some equipment had to be manufactured or modified from existing equipment. A functional test site with information gathering devices was accomplished as a result of thethesis. Test runs demonstrated that the Hydronip concept is, at least on a small scale,functional. Short-term tests for seal functioning showed that the seal can be lubricatedsufficiently under different kinds of nip load situations. Wad tests demonstrated that the metal belt is durable against different sizes of external particles. The seal also endured wad tests even though the pressure impacts impaired the lubrication. MTS tests showing dry content increases, combined with a rough cost calculation and the basic function of the machine in test runs, show that with some further study Hydronip could be a promising new product for water removal from a paper or board machine’s press section.

EDTA- and DTPA-functionalized silica gel and chitosan adsorbents for the removal of heavy metals from aqueous solutions

Adsorbents functionalized with chelating agents are effective in removal of heavy metals from aqueous solutions. Important properties of such adsorbents are high binding affinity as well as regenerability. In this study, aminopolycarboxylic acid, EDTA and DTPA, were immobilized on the surface of silica gel, chitosan, and their hybrid materials to achieve chelating adsorbents for heavy metals such as Co(II), Ni(II), Cd(II), and Pb(II). New knowledge about the adsorption properties of EDTA- and DTPA-functionalizedadsorbents was obtained. Experimental work showed the effectiveness, regenerability, and stability of the studied adsorbents. Both advantages and disadvantages of the adsorbents were evaluated. For example, the EDTA-functionalized chitosan-silica hybrid materials combined the benefits of the silica gel and chitosan while at the same time diminishing their observed drawbacks. Modeling of adsorption kinetics and isotherms is an important step in design process. Therefore, several kinetic and isotherm models were introduced and applied in this work. Important aspects such as effect of error function, data range, initial guess values, and linearization were discussed and investigated. The selection of the most suitable model was conducted by comparing the experimental and simulated data as well as evaluating the correspondence between the theory behind the model and properties of the adsorbent. In addition, modeling of two-component data was conducted using various extended isotherms. Modeling results for both one- and twocomponent systems supported each other. Finally, application testing of EDTA- and DTPA-functionalized adsorbents was conducted. The most important result was the applicability of DTPA-functionalized silica gel and chitosan in the capturing of Co(II) from its aqueous EDTA-chelate. Moreover, these adsorbents were efficient in various solution matrices. In addition, separation of Ni(II) from Co(II) and Ni(II) and Pb(II) from Co(II) and Cd(II) was observed in two- and multimetal systems. Lastly, prior to their analysis, EDTA- and DTPA-functionalized silica gels were successfully used to preconcentrate metal ions from both pure and salty waters

Sähkömoottoriprototyypin mekaniikkasuunnittelu järjestelmällisen tuotesuunnittelun avulla

Työn tavoitteena oli suunnitella sähkömoottoriprototyyppi, joka soveltuu hybridiajoneuvon ajomoottoriksi. Mekaniikkasuunnittelu toteutettiin samanaikaisesti sähkösuunnittelun kanssa ja siinä käytettiin yleisesti käytössä olevaa järjestelmällistä tuotesuunnittelua. Järjestelmällinen tuotesuunnittelu soveltuu laajoihin suunnitteluprojekteihin, sillä sen avulla suunnitteluprosessi on jaoteltu useampiin pieniin askeliin. Työssä esitetään sähkömoottorin yleistä toimintaperiaatetta sekä niitä sähköteknisiä erityispiirteitä, joita mekaniikkasuunnittelussa tulee ottaa huomioon. Työn tuloksissa käytiin yksityiskohtaisesti läpi roottorin suunnittelu. Muille komponenteille käytettiin samaa järjestelmällistä tuotesuunnittelua mutta niitä ei esitetä yksityiskohtaisesti tässä työssä. Kokonaisuudessaan sähkömoottorista saatiin suunniteltua ratkaisuehdotus, joka täyttää halutut vaatimukset. Lisäksi työssä kerättiin kattava lista standardeista, jotka tukevat sähkömoottorin suunnittelua. Järjestelmällisen tuotesuunnittelun todettiin soveltuvan sähkömoottorin suunnitteluun hyvin ja saatua ratkaisuehdotusta voidaan pitää toimivana. Moottori suunnitelmasta valmistetaan ensimmäinen prototyyppi keväällä 2012. Prototyyppiä voidaan kehittää suunnittelemalla siitä paremmin sarjatuotantoon soveltuva malli esimerkiksi vähentämällä koneistettavien osien määrää ja korvaamalla ne valukappaleilla.

Optimization of hydrogen plant efficiency

The purpose of this master’s thesis was to study ways to increase the operating cost-efficiency of the hydrogen production process by optimizing the process parameters while, at the same time, maintaining plant reliability and safety. The literature part reviewed other hydrogen production and purification processes as well as raw material alternatives for hydrogen production. The experimental part of the master’s thesis was conducted at Solvay Chemicals Finland Oy’s hydrogen plant in spring 2012. It was performed by changing the process parameters, first, one by one, aiming for a more efficient process with clean product gas and lower natural gas consumption. The values of the process parameters were tested based on the information from the literature, process simulation and experiences of previous similar processes. The studied parameters were reformer outlet temperature, shift converter inlet temperature and steam/carbon ratio. The results show that the optimal process conditions are a lower steam/carbon ratio and reformer outlet temperature than the current values of 3.0 and 798 °C. An increase/decrease in the shift conversion inlet temperature does not affect natural gas consumption, but it has an effect on minimizing the process steam overload.

Painevesityyppisen ydinvoimalaitoksen sekundääripiirin mallinnus

Tutkimuksen tavoitteena oli kehittää entistä tarkempi ja luotettavampi työkalu Loviisan ydinvoimalaitoksen ensimmäisen reaktoriyksikön sekundääripiirin 50-linjan stationääritilan toiminnan arviointiin. Toisena tavoitteena oli kartoittaa ja raportoida mallintamiseen käytetyn SOLVO-ohjelman kehitysmahdollisuuksia. Tutkimusten perusteella kehitettiin testatusti toimiva prosessimalli, joka dokumentoitiin ja validoitiin yksityiskohtaisesti. Tulevaisuudessa tapahtuvaa kehitystyötä, ja mallin käyttöä varten kehitettiin lisäksi Excel-pohjainen työkalu, jonka avulla SOLVO:n ja Excelin välinen integraatio voidaan myöhemmin julkaistavassa SOLVO:n versiossa viedä nykyistä pidemmälle. Mallintamistyön ohella tutkimuksen aikana selvitettiin olennaisimmat SOLVO:n erityispiirteet ja vahvuudet sekä kartoitettiin sen käyttöön liittyvät kehitystarpeet. Tärkeimpänä kehitysehdotuksena nousi esiin yksittäisissä komponenteissa suoritetun laskennan läpinäkyvyyden parantaminen. Seuraavassa kehitysvaiheessa myös komponenttikohtaiset laskentayhtälöt olisi suositeltavaa asettaa avoimiksi käyttäjäkohtaisille muutoksille. Työn aikana saavutettiin myös muita merkittäviä tuloksia, jotka liittyivät pääosin rinnak-kaisten 10- ja 50-linjojen välisiin yhteyksiin. Linjojen välisiä vaikutuksia analysoitaessa huomattiin niiden olevan olennaisessa asemassa erityisesti sarja-ajon aikana. Mikäli mallilla halutaan kuvata sekä sarja- että rinnanajoa, sen on käsitettävä molemmat linjat ja kaikki niihin liittyvät komponentit. Edellä mainitun lisäksi mallipohjaisen tarkastelun tuloksena tehtiin havaintoja, joiden perusteella nykyistä prosessia voidaan edelleen kehittää. Näistä havainnoista tärkeimpänä merivesipumppujen optimaalisen säätölämpötilan todettiin asettuvan 4,5 – 4,6 °C välille. Toinen huomio liittyi matalapaineturbiinien ulosvirtaushäviöihin, joihin hukataan juoksusta riippuen keskimäärin noin 10 kJ/kg enemmän entalpiaa kuin parhaassa mahdollisessa tapauksessa. Validoinnin yhteydessä havaituista pienistä poikkeamista huolimatta kehitetty malli vastaa hyvin laitokselta saatuja mittaustuloksia sekä muita samassa yhteydessä käytettyjä luotet-tavuuden arviointikriteerejä.

Assessing the Environmental Value of Water Treatment Solutions in the Mining Industry

Environmental accountability has become a major source of competitive advantage for industrial companies, because customers consider it as relevant buying criterion. However, in order to leverage their environmental responsibility, industrial suppliers have to be able to demonstrate the environmental value of their products and services, which is also the aim of Kemira, a global water chemistry company considered in this study. The aim of this thesis is to develop a tool which Kemira can use to assess the environmental value of their solutions for the customer companies in mining industry. This study answers to questions on what kinds of methods to assess environmental impacts exist, and what kind of tool could be used to assess the environmental value of Kemira’s water treatment solutions. The environmental impacts of mining activities vary greatly between different mines. Generally the major impacts include the water related issues and wastes. Energy consumption is also a significant environmental aspect. Water related issues include water consumption and impacts in water quality. There are several methods to assess environmental impacts, for example life cycle assessment, eco-efficiency tools, footprint calculations and process simulation. In addition the corresponding financial value may be estimated utilizing monetary assessment methods. Some of the industrial companies considered in the analysis of industry best practices use environmental and sustainability assessments. Based on the theoretical research and conducted interviews, an Excel based tool utilizing reference data on previous customer cases and customer specific test results was considered to be most suitable to assess the environmental value of Kemira’s solutions. The tool can be used to demonstrate the functionality of Kemira’s solutions in customers’ processes, their impacts in other process parameters and their environmental and financial aspects. In the future, the tool may be applied to fit also Kemira’s other segments, not only mining industry.

Performance and scalability of isolated DC-DC converter topologies in low voltage, high current applications

Fuel cells are a promising alternative for clean and efficient energy production. A fuel cell is probably the most demanding of all distributed generation power sources. It resembles a solar cell in many ways, but sets strict limits to current ripple, common mode voltages and load variations. The typically low output voltage from the fuel cell stack needs to be boosted to a higher voltage level for grid interfacing. Due to the high electrical efficiency of the fuel cell, there is a need for high efficiency power converters, and in the case of low voltage, high current and galvanic isolation, the implementation of such converters is not a trivial task. This thesis presents galvanically isolated DC-DC converter topologies that have favorable characteristics for fuel cell usage and reviews the topologies from the viewpoint of electrical efficiency and cost efficiency. The focus is on evaluating the design issues when considering a single converter module having large current stresses. The dominating loss mechanism in low voltage, high current applications is conduction losses. In the case of MOSFETs, the conduction losses can be efficiently reduced by paralleling, but in the case of diodes, the effectiveness of paralleling depends strongly on the semiconductor material, diode parameters and output configuration. The transformer winding losses can be a major source of losses if the windings are not optimized according to the topology and the operating conditions. Transformer prototyping can be expensive and time consuming, and thus it is preferable to utilize various calculation methods during the design process in order to evaluate the performance of the transformer. This thesis reviews calculation methods for solid wire, litz wire and copper foil winding losses, and in order to evaluate the applicability of the methods, the calculations are compared against measurements and FEM simulations. By selecting a proper calculation method for each winding type, the winding losses can be predicted quite accurately before actually constructing the transformer. The transformer leakage inductance, the amount of which can also be calculated with reasonable accuracy, has a significant impact on the semiconductor switching losses. Therefore, the leakage inductance effects should also be taken into account when considering the overall efficiency of the converter. It is demonstrated in this thesis that although there are some distinctive differences in the loss distributions between the converter topologies, the differences in the overall efficiency can remain within a range of a few percentage points. However, the optimization effort required in order to achieve the high efficiencies is quite different in each topology. In the presence of practical constraints such as manufacturing complexity or cost, the question of topology selection can become crucial.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Vastaanottoprosessin nopeuttaminen ja virheiden eliminointi RFID-tekniikan avulla

Työn tavoitteena oli tutkia ja kehittää saapuvan tavaran vastaanottoprosessia poistaen siitä Lean-oppien mukaisesti hukkaa. Kehitys tehtiin lisäämällä vastaanoton tiedonsiirtoautomatiikkaa, ja toteutus tehtiin RFID-tekniikan avulla. Tutkielman teoreettisena taustana ovat Lean-opit, joiden avulla tavoitteena oli eliminoida hukka, suunnitella vastaanottoprosessi uudelleen ja kehittää sitä edelleen. Keskeisenä tehtävänä oli löytää ne tekniikan valintaan vaikuttavat tekijät, joilla case-yrityksessä saatiin käyttövarma RDIF-tekniikka käyttöön. Tutkielmassa kerrotaan myös, miten tekniikan käyttöönotto toteutettiin. Lopuksi esitetään tuloksia ja päätelmiä uudistetusta prosessista ja kerrotaan niistä jatkotoimenpiteistä, joiden avulla teknologian käyttöä voidaan edelleen laajentaa. The aim of this study was analyze and develop the inbound receiving process of removing waste according of Lean-thinking. Development was done by raising inbound transmission automation implementation done by RFID- technology. The theoretical background was Lean –thinking; how to re-design process further development to eliminate waste. The main task was to find a reliable RFID- technology and the choice of technology factors were taken into account in the case company and how the technology was implemented. Finally, the presented results and conclusions of re-design process and possibilities to expand the technology to the case company processes.

Työkoneiden dieselmoottoreiden hyötysuhteen parantaminen lämmöntalteenoton avulla

Tämä diplomityö on osa Lappeenrannan teknillisessä yliopistossa tehtävää tutkimusta polttomoottoreiden energiatehokkuuden parantamisessa. Työn tavoitteena on saada tutkimustietoa polttomoottoreiden hukkalämpövirtojen hyödyntämisestä sähköntuotannossa. Tavoitteena on muodostaa näkemys Mikro-ORC energiamuuntimen mahdollisuuksista ja reunaehdoista osana työkoneluokan (150 kW… 400 kW) dieselmoottorikokonaisuutta, erityisesti maataloussektorilla. Työssä tarkasteltaviksi moottoreiksi valittiin kaksi eri AGCO Sisu Powerin dieselmoottoria. Laskennat suoritettiin moottorin valmistajan antamien hukkalämpövirtojen arvojen perusteella. Laskennan perusperiaatteena oli tutkia ORC-prosessin tuottamaa lisäsähkötehoa hyödyntämällä pakokaasujen lämpöenergiaa korkea-, keski- ja matalalämpötiloissa. Työssä vertailtiin kahden eri kiertoaineen prosessihyötysuhdetta, saatava sähkötehoa sekä prosessin sisäisiä parametreja. Lisäksi työssä tutkittiin ORC-prosessin laskentaa suunnittelupisteessä (design) ja suunnittelupisteen ulkopuolella (off-design), prosessisuureiden optimointia ja lämmönsiirtimien mitoitusta. Diplomityössä tarkasteltiin moottorin energiataseen mukaisten arvojen lisäksi moottorin parametrien muuttamisen vaikutusta hukkalämpövirroista saatavan tehoon. Työssä saatiin arvokasta tietoa polttomoottoreiden hukkalämpövirtojen muuntamisesta sähköksi ORC:lla sekä moottorin energiatehokkuuden parantamisesta.

Performance measurement and management in a collaborative network

This study concerns performance measurement and management in a collaborative network. Collaboration between companies has been increased in recent years due to the turbulent operating environment. The literature shows that there is a need for more comprehensive research on performance measurement in networks and the use of measurement information in their management. This study examines the development process and uses of a performance measurement system supporting performance management in a collaborative network. There are two main research questions: how to design a performance measurement system for a collaborative network and how to manage performance in a collaborative network. The work can be characterised as a qualitative single case study. The empirical data was collected in a Finnish collaborative network, which consists of a leading company and a reseller network. The work is based on five research articles applying various research methods. The research questions are examined at the network level and at the single network partner level. The study contributes to the earlier literature by producing new and deeper understanding of network-level performance measurement and management. A three-step process model is presented to support the performance measurement system design process. The process model has been tested in another collaborative network. The study also examines the factors affecting the process of designing the measurement system. The results show that a participatory development style, network culture, and outside facilitators have a positive effect on the design process. The study increases understanding of how to manage performance in a collaborative network and what kind of uses of performance information can be identified in a collaborative network. The results show that the performance measurement system is an applicable tool to manage the performance of a network. The results reveal that trust and openness increased during the utilisation of the performance measurement system, and operations became more transparent. The study also presents a management model that evaluates the maturity of performance management in a collaborative network. The model is a practical tool that helps to analyse the current stage of the performance management of a collaborative network and to develop it further.

Häiriöanalyysejä tehonkorotetun kiehutusvesivoimalaitoksen käytettävyyden varmistamiseksi

TVO suunnittelee reaktoritehon 10 %:n korotusta Olkiluoto 1 ja 2 -voimalaitoksille. Reaktoriteho nostetaan 2500 MW:sta 2750 MW:iin polttoaineen rikastusastetta nostamalla ja pääkiertovirtausta kasvattamalla. Samalla syöttövesivirtaus reaktoriin ja tuorehöyryvirtaus turpiineille kasvaa. Lauhteenpuhdistusjärjestelmän kapasiteettia ei voida kuitenkaan kasvattaa, joten massavirran lisäys toteutetaan ottamalla käyttöön korkeapainesivulauhteen eteenpäinpumppaus. Lauhteen esilämmityslinjojen, lauhteenpuhdistuksen ja syöttövesipumppujen massavirta säilyy siten nykyisellään. Muita merkittäviä tehonkorotukseen liittyviä laitosmuutoksia ovat pääkiertopumppujen uusinta ja korkeapaineturpiinin muutokset. Tehonkorotetun prosessin käytettävyyden varmistamiseksi tehdään häiriöanalyysejä Apros-prosessisimulointiohjelmistoa käyttäen. OL1 ja OL2 -laitoksista on olemassa validoitu 2500 MW:n laitosmalli, josta muokatulla 2750 MW:n laitosmallilla simuloinnit tehdään. Häiriöanalyysien avulla selvitetään säätöjärjestelmien kyky pitää prosessin tila hallinnassa ilman suojausautomaation laukeamista. Simuloituihin tapauksiin kuuluu pumppujen ja venttiilien vikaantumistapauksia sekä turpiini- ja reaktoripuolen pikasulku- ja osittaispikasulkutapauksia. Myös meriveden lämpötilan vaikutusta häiriötilanteisiin tarkastellaan. Analyysien perusteella voimalaitosten ohjaus- ja suojausautomaatio toimivat hyvin myös korotetulla teholla. Tehonkorotuksen jälkeiset suuremmat massavirrat aiheuttavat kuitenkin voimakkaampia reaktoripaineen ja -tehon vaihteluita varsinkin venttiilien sulkeutumistapauksissa. Simuloinnit osoittivat, että tehonkorotus 2500 MW:sta 2750 MW:iin on mahdollinen, mutta aiheuttaa pieniä muutoksia laitoksen suojausjärjestelmien laukaisurajoihin.

Importance of considering food waste in the development of sustainable food packaging systems

Meeting the needs of both present and future generations forms the foundation of sustainable development. Concern about food demand is increasing alongside the continuously growing population. In the pursuit of food security preventing food waste is one solution avoiding the negative environmental impacts that result from producing food unnecessarily. Packages offer one answer to preventing food waste, as they 1) preserve and protect food, 2) introduce the user to the correct way to handle and use the food and package and 3) allow the user to consume the food in its entirety. This thesis aims to enhance the sustainability of food packages by giving special emphasis to preventing food waste. The focus of this thesis is to assist the packaging designer in being able to take into account the requirements for the sustainability of food packages and to be able to integrate these requirements into the product development process. In addition, life cycle methods that can be used as a tool in the packaging design process or in assessing the sustainability of finished food-packaging combinations are evaluated. The methods of life cycle costing (LCC) and life cycle working environment (LCWE) are briefly discussed. The method of life cycle assessment (LCA) is examined more thoroughly through the lens of the literature review of food-package LCA case studies published in the 21st century in three relevant journals. Based on this review and on experiences learned from conducting LCAs, recommendations are given as to how the LCA practitioner should conduct a food packaging study to make most of the results. Two case studies are presented in this thesis. The first case study relates the results of a life cycle assessment conducted for three food items (cold cut (ham), sliced dark bread (rye) and Soygurt drink) and the alternative packaging options of each. Results of this study show that the packaging constitutes only 1–12 % of the total environmental impacts of the food-packaging combination. The greatest effect is derived from the food itself and the wasted food. Even just a small percentage of wasted food causes more environmental impacts than does the packaging. The second case study presents the results of LCC and LCWE analysis done for fruit and vegetable transport packages. In this thesis, the specific results of the study itself are not the focus, but rather the study methods and scope are analysed based on how these complement the sustainability assessment of food packages. This thesis presents reasons why prevention of food waste should be more thoroughly taken into account in food packaging design. In addition, the task of the packaging designer is facilitated by the requirements of sustainable food packaging, by the methods and step-by-step guidance on how to integrate sustainability issues into the design process, and by the recommendations on how to assess the sustainability of food packages. The intention of this thesis is to express the issues that are important in the field of the food packaging industry. Having recognised and implemented these issues, businesses can better manage the risks that could follow from neglecting these sustainability aspects.

Liiketoiminnan strateginen suunnittelu: Konesali-liiketoiminta

Tässä diplomityössä selvitettiin tukkuliikkeen liiketoimintamahdollisuuksia konesali-liiketoiminnassa. Päätutkimuskysymys oli: Millainen liiketoimintamalli soveltuu kestävään arvontuotantoon tukkuliikkeelle konesali-liiketoiminnassa? Työn teoriaosassa paneudutaan strategiseen suunnitteluun, liiketoimintamalleihin ja liiketoimintamallien suunnitteluun. Teoriaosan pohjalta johdettiin vaatimukset ja luotiin viitekehys liiketoimintamallien suunnittelulle. Ongelmanratkaisu aloitettiin toimintaympäristön analyysillä, jonka pohjalta tunnistettiin liiketoimintamahdollisuuksia. Kerättyä dataa analysoitiin erilaisilla analysointimenetelmillä liikemahdollisuuksien tunnistamiseksi. Tämän jälkeen tunnistettuja liiketoimintamahdollisuuksia arvioitiin ja kaikkein potentiaalisimmat ideat kehitettiin liiketoimintamalleiksi. Työn varsinaiset tulokset jakautuvat kolmeen osaan: Toimintaympäristön analyysiin, kehitettyihin konsepteihin ja suunnitelmaan konseptien käyttöönotosta. Toimintaympäristön analyysi sisältää makro- ja mikroympäristön analysoinnin, joita voidaan hyödyntää, jos jokin liiketoimintamalleista päätetään ottaa käyttöön. Toimintaympäristön analyysin perusteella voidaan tehdä johtopäätös, etteivät tukkuliikkeen resurssit sovellu perinteiseen konesaliliiketoiminnan arvontuotantoon. Tutkimuksen tärkein tulos on kuitenkin kehitetyt liiketoimintamallit, jotka pystyvät hyödyntämään olemassa olevia resursseja ja silti olemaan kilpailukykyisiä konesali-liiketoiminnassa.