An autonomous wave-powered desalination system

The potential for an autonomous wave-powered desalination system is considered and it is identified that the most promising configuration is a reverse osmosis (RO) plant utilising a pressure exchanger-intensifier for energy recovery. A numerical model of the RO plant with a pressure exchanger-intensifier is developed that shows that a specific energy consumption of less than 2.0 kW h/m3 over a wide range of sea-water feed conditions, making it particularly suitable for use with a variable power source such as wave energy. A numerical model of the combined wave-power and desalination plant is also developed that shows that it is possible to supply the desalination plant with sea-water directly pressurised by the wave energy converter, eliminating the cost and energy losses associated with converting the energy into electricity and back to pressurised water. For a typical sea-state the specific hydraulic energy consumption of the desalination plant is estimated to be 1.85 kW h/m3 whilst maintaining a recovery-ratio of less than 25 to 35% to avoid the need for chemical pre-treatment to eliminate scaling problems. It is suggested that the economic potential for wave-powered desalination depends on these energy and cost savings more than compensating for the reduction in membrane life that occurs with variable feed conditions.

Decoupled-DFIG fault ride-through strategy for enhanced stability performance during grid faults

This paper proposes a decoupled fault ride-through strategy for a doubly fed induction generator (DFIG) to enhance network stability during grid disturbances. The decoupled operation proposes that a DFIG operates as an induction generator (IG) with the converter unit acting as a reactive power source during a fault condition. The transition power characteristics of the DFIG have been analyzed to derive the capability of the proposed strategy under various system conditions. The optimal crowbar resistance is obtained to exploit the maximum power capability from the DFIG during decoupled operation. The methods have been established to ensure proper coordination between the IG mode and reactive power compensation from the grid-side converter during decoupled operation. The viability and benefits of the proposed strategy are demonstrated using different test network structures and different wind penetration levels. Control performance has been benchmarked against existing grid code standards and commercial wind generator systems, based on the optimal network support required (i.e., voltage or frequency) by the system operator from a wind farm installed at a particular location.

A virtual inspection framework for precision manufacturing of aerofoil components

The finite element method plays an extremely important role in forging process design as it provides a valid means to quantify forging errors and thereby govern die shape modification to improve the dimensional accuracy of the component. However, this dependency on process simulation could raise significant problems and present a major drawback if the finite element simulation results were inaccurate. This paper presents a novel approach to assess the dimensional accuracy and shape quality of aeroengine blades formed from finite element hot-forging simulation. The proposed virtual inspection system uses conventional algorithms adopted by modern coordinate measurement processes as well as the latest free-form surface evaluation techniques to provide a robust framework for virtual forging error assessment. Established techniques for the physical registration of real components have been adapted to localise virtual models in relation to a nominal Design Coordinate System. Blades are then automatically analysed using a series of intelligent routines to generate measurement data and compute dimensional errors. The results of a comparison study indicate that the virtual inspection results and actual coordinate measurement data are highly comparable, validating the approach as an effective and accurate means to quantify forging error in a virtual environment. Consequently, this provides adequate justification for the implementation of the virtual inspection system in the virtual process design, modelling and validation of forged aeroengine blades in industry.

"Arqueologias" das aprendizagens em Capelins (Santo António) - Alandroal (1997-2007)

Esta dissertação de mestrado desenvolveu-se no âmbito do projecto “Arqueologia” das Aprendizagens no concelho de Alandroal, que teve, como objectivo primordial, a identificação e caracterização do universo de aprendizagens institucionais disponíveis e concretizadas pela comunidade do território em estudo (Freguesia de Capelins (Santo António) /Alandroal), na década 1997 – 2007. Foram inquiridas, nesta freguesia, 16 instituições e identificadas 30 aprendizagens institucionais, que tiveram maior ocorrência nos anos de 2004, 2005 e 2006. Embora seja uma freguesia essencialmente rural, a área de actividade da maioria das instituições identificadas inscreve-se no sector do comércio por grosso e a retalho e de reparação de veículos automóveis e motociclos. São, na sua maioria, instituições de natureza privada e reveladoras de organização, no que respeita à sua organização. No entanto, o relacionamento interinstitucional foi pouco dinâmico, existindo um fraco trabalho em rede. Quando existiram parcerias, estas ocorreram extra freguesia e, até mesmo, extra concelho. Seguindo uma análise quantitativa dos dados extraídos da aplicação dos questionários, com recurso a análise estatística, conclui-se que os processos de aprendizagem das instituições inquiridas da freguesia de Capelins apresentam características centradas nas próprias instituições promotoras dessas mesmas aprendizagens, assentes na formação do pessoal, com carácter formal e não formal e relacionaram-se com as áreas de administração pública e defesa, alojamento e restauração e ainda com a área do comércio por grosso e a retalho; ABSTRACT: This dissertation developed under the project "Archaeology" of Learning in the county of Alandroal, which had as its primary objective, the identification and characterization of the universe of available institutional learning and implemented by the community of the area under study (Parish of capelin (San Antonio) / Alandroal), in the decade from 1997 to 2007. Were surveyed in this parish, and 16 institutions identified 30 institutional learning, which have a higher occurrence in the years 2004, 2005 and 2006. Although it is an essentially rural, the parish area of activity of most institutions identified in the sector of wholesale and retail trade and repair of motor vehicles and motorcycles. Are, for the most part, private institutions and revealing of organization, with regard to its organization. However, the interinstitutional relationship was weak and there is a little dynamic networking. When partnered, this extra parish occurred and even extra municipality. Following a quantitative analysis of data taken from the application of questionnaires, using statistical analysis, it is concluded that the learning processes of the institutions surveyed in the parish of Capelins characteristics focused on promoting institutions of those learnings, based on staff training, formal and non-formal nature and related to the areas of public administration and defense, hotels and restaurants and also the area of wholesale and retail trade.

A risk-averse optimization model for trading wind energy in a market environment under uncertainty

In this paper, a stochastic programming approach is proposed for trading wind energy in a market environment under uncertainty. Uncertainty in the energy market prices is the main cause of high volatility of profits achieved by power producers. The volatile and intermittent nature of wind energy represents another source of uncertainty. Hence, each uncertain parameter is modeled by scenarios, where each scenario represents a plausible realization of the uncertain parameters with an associated occurrence probability. Also, an appropriate risk measurement is considered. The proposed approach is applied on a realistic case study, based on a wind farm in Portugal. Finally, conclusions are duly drawn. (C) 2011 Elsevier Ltd. All rights reserved.

Fonte de carga de condensadores de alta tensão com compensação de fator potência

Trabalho Final de Mestrado para a obtenção do grau de Mestre em Engenharia Electrotécnica Ramo de Automação e Electrónica Industrial

Real-time Energy Resource Scheduling considering a Real Portuguese Scenario

The development in power systems and the introduction of decentralized generation and Electric Vehicles (EVs), both connected to distribution networks, represents a major challenge in the planning and operation issues. This new paradigm requires a new energy resources management approach which considers not only the generation, but also the management of loads through demand response programs, energy storage units, EVs and other players in a liberalized electricity markets environment. This paper proposes a methodology to be used by Virtual Power Players (VPPs), concerning the energy resource scheduling in smart grids, considering day-ahead, hour-ahead and real-time scheduling. The case study considers a 33-bus distribution network with high penetration of distributed energy resources. The wind generation profile is based on a real Portuguese wind farm. Four scenarios are presented taking into account 0, 1, 2 and 5 periods (hours or minutes) ahead of the scheduling period in the hour-ahead and realtime scheduling.

Imparidades em inventários

Dissertação de Mestrado apresentada ao Instituto de Contabilidade e Administração do Porto para a obtenção do grau de Mestre em Contabilidade e Finanças, sob orientação da Doutora Albertina Paula Monteiro Esta versão contém as críticas e sugestões dos elementos do júri.

Utilização de sensores de baixo custo na medição de monóxido de carbono no ar ambiente

Nos últimos anos tem-se assistido à introdução de novos dispositivos de medição da poluição do ar baseados na utilização de sensores de baixo custo. A utilização menos complexa destes sistemas, possibilita a obtenção de dados com elevada resolução temporal e espacial, abrindo novas oportunidades para diferentes metodologias de estudos de monitorização da poluição do ar. Apesar de apresentarem capacidades analíticas distantes dos métodos de referência, a utilização destes sensores tem sido sugerida e incentivada pela União Europeia no âmbito das medições indicativas previstas na Diretiva 2008/50/CE, com uma incerteza expandida máxima de 25%. O trabalho desenvolvido no âmbito da disciplina de Projeto consistiu na escolha, caracterização e utilização em medições reais de um sensor de qualidade do ar, integrado num equipamento protótipo desenvolvido com esse fim, visando obtenção uma estimativa da incerteza de medição associada à utilização deste dispositivo através da aplicação da metodologia de demonstração de equivalência de métodos de medição de qualidade do ar definida pela União Europeia. A pesquisa bibliográfica realizada permitiu constatar que o monóxido de carbono é neste momento o parâmetro de qualidade do ar que permite ser medido de forma mais exata através da utilização de sensores, nomeadamente o sensor eletroquímico da marca Alphasense, modelo COB4, amplamente utilizado em projetos de desenvolvimento neste cotexto de monitorização ambiental. O sensor foi integrado num sistema de medição com o objetivo de poder ser utlizado em condições de autonomia de fornecimento de energia elétrica, aquisição interna dos dados, tendo em consideração ser o mais pequeno possível e de baixo custo. Foi utlizado um sistema baseado na placa Arduino Uno com gravação de dados em cartão de memória SD, baterias e painel solar, permitindo para além do registo das tensões elétricas do sensor, a obtenção dos valores de temperatura, humidade relativa e pressão atmosférica, com um custo global a rondar os 300 euros. Numa primeira fase foram executados um conjunto de testes laboratoriais que permitiram a determinação de várias características de desempenho em dois sensores iguais: tempo de resposta, a equação modelo do sensor, avaliação da repetibilidade, desvio de curto e longo termo, interferência da temperatura e histerese. Os resultados demonstraram um comportamento dos sensores muito linear, com um tempo de resposta inferior a um minuto e com uma equação modelo do sensor dependente da variação da temperatura. A estimativa da incerteza expandida laboratorial ficou, para ambos os sensores, abaixo dos 10%. Após a realização de duas campanhas reais de medição de CO em que os valores foram muito baixos, foi realizada uma campanha de quinze dias num parque de estacionamento subterrâneo que permitiu a obtenção de concentrações suficientemente elevadas e a comparação dos resultados dos sensores com o método de referência em toda a gama de medição (0 a 12 mol.mol-1). Os valores de concentração obtidos pelos dois sensores demonstraram uma excelente correlação com o método de referência (r2≥0,998), obtendo-se resultados para a estimativa da incerteza expandida de campo inferiores aos obtidos para a incerteza laboratorial, cumprindo o objetivo de qualidade de dados definido para as medições indicativas de incerteza expandida máxima de 25%. Os resultados observados durante o trabalho realizado permitiram confirmar o bom desempenho que este tipo de sensor pode ter no âmbito de medições de poluição do ar com um caracter mais indicativo.

Secondary effects of catalytic diesel particulate filters: copper-induced formation of PCDD/Fs.

Potential risks of a secondary formation of polychlorinated dibenzodioxins/furans (PCDD/Fs) were assessed for two cordierite-based, wall-through diesel particulate filters (DPFs) for which soot combustion was either catalyzed with an iron- or a copper-based fuel additive. A heavy duty diesel engine was used as test platform, applying the eight-stage ISO 8178/4 C1 cycle. DPF applications neither affected the engine performance, nor did they increase NO, NO2, CO, and CO2 emissions. The latter is a metric for fuel consumption. THC emissions decreased by about 40% when deploying DPFs. PCDD/F emissions, with a focus on tetra- to octachlorinated congeners, were compared under standard and worst case conditions (enhanced chlorine uptake). The iron-catalyzed DPF neither increased PCDD/F emissions, nor did it change the congener pattern, even when traces of chlorine became available. In case of copper, PCDD/F emissions increased by up to 3 orders of magnitude from 22 to 200 to 12 700 pg I-TEQ/L with fuels of < 2, 14, and 110 microg/g chlorine, respectively. Mainly lower chlorinated DD/Fs were formed. Based on these substantial effects on PCDD/F emissions, the copper-catalyzed DPF system was not approved for workplace applications, whereas the iron system fulfilled all the specifications of the Swiss procedures for DPF approval (VERT).

Potentiel d’une approche populationnelle orientée vers la reconfiguration des environnements urbains pour améliorer la sécurité des piétons

INTRODUCTION : En milieu urbain, l’amélioration de la sécurité des piétons pose un défi de santé publique. Pour chaque décès attribuable aux collisions routières, il y a des centaines de personnes blessées et, dans les pays riches, la diminution du nombre annuel de piétons décédés s’expliquerait en partie par la diminution de la marche. Les stratégies préventives prédominantes n’interviennent pas sur le volume de circulation automobile, un facteur pourtant fondamental. De plus, les interventions environnementales pour améliorer la sécurité des infrastructures routières se limitent habituellement aux sites comptant le plus grand nombre de décès ou de blessés. Cette thèse vise à décrire la contribution des volumes de circulation automobile, des pratiques locales de marche et de la géométrie des routes au nombre et à la répartition des piétons blessés en milieu urbain, et d’ainsi établir le potentiel d’une approche populationnelle orientée vers la reconfiguration des environnements urbains pour améliorer la sécurité des piétons. MÉTHODE : Le devis est de type descriptif et transversal. Les principales sources de données sont les registres des services ambulanciers d’Urgences-santé (blessés de la route), l’enquête Origine-Destination (volumes de circulation automobile), la Géobase du réseau routier montréalais (géométrie des routes) et le recensement canadien (pratiques locales de marche, position socioéconomique). Les analyses descriptives comprennent la localisation cartographique (coordonnées x,y) de l’ensemble des sites de collision. Des modèles de régression multi-niveaux nichent les intersections dans les secteurs de recensement et dans les arrondissements. RÉSULTATS : Les analyses descriptives démontrent une grande dispersion des sites de collision au sein des quartiers. Les analyses multivariées démontrent les effets significatifs, indépendants du volume de circulation automobile, de la présence d’artère(s) et d’une quatrième branche aux intersections, ainsi que du volume de marche dans le secteur, sur le nombre de piétons blessés aux intersections. L’analyse multi-niveaux démontre une grande variation spatiale de l’effet du volume de circulation automobile. Les facteurs environnementaux expliquent une part substantielle de la variation spatiale du nombre de blessés et du gradient socioéconomique observé. DISCUSSION : La grande dispersion des sites de collision confirme la pertinence d’une approche ne se limitant pas aux sites comptant le plus grand nombre de blessés. Les résultats suggèrent que des stratégies préventives basées sur des approches environnementales et populationnelle pourraient considérablement réduire le nombre de piétons blessés ainsi que les inégalités observées entre les quartiers.

Road novel, road movie : approche chronotopique du récit de la route

Thèse réalisée en cotutelle, sous la direction de M. Philippe Despoix (Université de Montréal) et de M. Michel Marie (Université Sorbonne Nouvelle-Paris 3)

Studies On Preparation And Characterization Of Hts Current Leads Using Multifilamentary Ag And Ag-Alloy Sheathed (Bi,Pb)-2223 Superconducting Tapes

The application vistas of superconductors have widened very much since the discovery of high TC superconductors (HTS) as many of the applications can be realised at 77 K rather than going down to 4.2 K, the liquid He temperature. One such application is the HTS current lead which is used to connect a superconducting system with a room temperature power source. Minimising heat leak to the cryogenic environment is the main advantage of introducing current leads into superconducting systems. The properties of HTSS likes zero resistance (avoiding joule heating) and very low thermal conductivity (minimized conductive heat transfer) make them ideal candidates to be used as current leads. There are two forms of HTS current leads. (i) bulk form (tube or rod) prepared either from YBCO or BSCCO and (ii) tape form prepared from Bi-2223 multifilamentary tapes. The tape form of current leads has many advantages with respect to the mechanical and thermal stability related criteria. Crucial information on various aspects of HTS current lead development are not available in the literature as those are kept proprietary by various companies around the world. The present work has been undertaken to tailor the properties of multifilamentary tapes for the current lead application and to optimise the processing parameters of the same for enhanced critical current density and field tolerance. Also it is the aim of the present investigation is to prepare prototype current leads engineered for operation in conduction cooled mode and test them for operational stability

Efectos en las ventas del sector automotor en Colombia frente a la aprobación del tratado de libre comercio con Estados Unidos

Esta investigación se realizó con el objetivo de conocer los efectos sobre las ventas del sector automotor en Colombia frente a la aprobación y puesta en marcha de Tratado de Libre Comercio con Estados Unidos, permitiendo brindar un panorama al sector y unas recomendaciones que le permitieran ser competitivo y no afectar considerablemente su nivel de ventas en general; Para ello, se analizaron únicamente los vehículos automotores para el transporte de pasajeros, que serán sin lugar a dudas los de mayor movimiento durante el TLC. Para ello, se contó principalmente con el diamante de competitividad propuesto por el catedrático Michael Porter para observar aquellos factores críticos dentro del sector que afectaban su competitividad y nivel de ventas, permitiendo así mismo hacer una comparación frente al sector automotor de Estados Unidos y conocer aquellos factores a trabajar por parte del sector en Colombia;, Contando con información ofrecida por parte de las autoridades del sector y asesores comerciales de las principales ensambladoras del País. Luego de ello, y con el ánimo de brindar recomendaciones al sector, tomando en cuenta los factores a mejorar, se hizo uso de la prospectiva estratégica y la herramienta MICMAC (Matriz de impacto cruzado) con el fin de conocer los factores clave que influirían tanto en el corto, mediano y largo plazo en el sector automotor de Colombia y en los cuales se debería trabajar para buscar efectos positivos en el sector y sus ventas; Palabras Clave: Vehículos, Competitividad, Ventas, Prospectiva Estratégica, TLC, Economía, Infraestructura, Tecnología, Inversión

Estimulacion magnetica trascraneal en el desempeno motor en enfermedades del sistema nervioso central: Revision Sistematica

Introducción: El uso de la estimulación cerebral no invasiva en procesos de rehabilitación es de gran interés, por cuanto con mediación tecnológica se generan nuevas posibilidades de recuperación motora, a partir de la activación de la corteza cerebral. El objetivo del estudio es establecer la evidencia del uso terapéutico de la EMT, relacionado con el desempeño motor de pacientes con enfermedades del sistema nervioso central. Metodología: Se realizó una revisión sistemática de la literatura. Se incluyeron 10 estudios en el análisis cualitativo que incluyó la evaluación de calidad con la escala de Jadad y del riesgo de sesgo con la herramienta Cochrane. Fueron excluidos 1613 estudios. Se aplicó el protocolo del estudio para la extracción, revisión y validez de los estudios incluidos. Resultados: La evidencia disponible muestra resultados positivos del uso terapéutico de la EMT en el desempeño motor en aspectos como la aceleración, la fuerza de pinza y de agarre, la estabilidad y la fuerza muscular, así como una mejor velocidad de la marcha y una disminución en la frecuencia y severidad de los espasmos. Discusión: La EMT puede constituir una estrategia terapéutica para mejorar el desempeño motor en pacientes con ECV, Lesión Medular y enfermedad de Parkinson, que requiere más investigación por la heterogeneidad de los diseños y medidas de descenlace utilizados, así como por la alta variabilidad interindividual que hace complejo estandarizar los protocolos de su uso terapéutico.