Electronic transport in low temperature nanocrystalline silicon thin-film transistors obtained by Hot-Wire CVD

Hydrogenated nanocrystalline silicon (nc-Si:H) obtained by hot-wire chemical vapour deposition (HWCVD) at low substrate temperature (150 °C) has been incorporated as the active layer in bottom-gate thin-film transistors (TFTs). These devices were electrically characterised by measuring in vacuum the output and transfer characteristics for different temperatures. The field-effect mobility showed a thermally activated behaviour which could be attributed to carrier trapping at the band tails, as in hydrogenated amorphous silicon (a-Si:H), and potential barriers for the electronic transport. Trapped charge at the interfaces of the columns, which are typical in nc-Si:H, would account for these barriers. By using the Levinson technique, the quality of the material at the column boundaries could be studied. Finally, these results were interpreted according to the particular microstructure of nc-Si:H.

Microcrystalline silicon thin film transistors obtained by Hot-Wire CVD

Polysilicon thin film transistors (TFT) are of great interest in the field of large area microelectronics, especially because of their application as active elements in flat panel displays. Different deposition techniques are in tough competition with the objective to obtain device-quality polysilicon thin films at low temperature. In this paper we present the preliminary results obtained with the fabrication of TFT deposited by hot-wire chemical vapor deposition (HWCVD). Some results concerned with the structural characterization of the material and electrical performance of the device are presented.

Thin Film Transistors obtained by Hot-Wire CVD

Hydrogenated microcrystalline silicon films obtained at low temperature (150-280°C) by hot wire chemical vapour deposition at two different process pressures were measured by Raman spectroscopy, X-ray diffraction (XRD) spectroscopy and photothermal deflection spectroscopy (PDS). A crystalline fraction >90% with a subgap optical absortion 10 cm -1 at 0.8 eV were obtained in films deposited at growth rates >0.8 nm/s. These films were incorporated in n-channel thin film transistors and their electrical properties were measured. The saturation mobility was 0.72 ± 0.05 cm 2/ V s and the threshold voltage around 0.2 eV. The dependence of their conductance activation energies on gate voltages were related to the properties of the material.

Microdoping compensation of microcrystalline silicon obtained by Hot-Wire Chemical Vapour Deposition

Undoped hydrogenated microcrystalline silicon was obtained by hot-wire chemical vapour deposition at different silane-to-hydrogen ratios and low temperature (<300 °C). As well as technological aspects of the deposition process, we report structural, optical and electrical characterizations of the samples that were used as the active layer for preliminary p-i-n solar cells. Raman spectroscopy indicates that changing the hydrogen dilution can vary the crystalline fraction. From electrical measurements an unwanted n-type character is deduced for this undoped material. This effect could be due to a contaminant, probably oxygen, which is also observed in capacitance-voltage measurements on Schottky structures. The negative effect of contaminants on the device was dramatic and a compensated p-i-n structure was also deposited to enhance the cell performance.

Lujien terästen hitsauksen kehittäminen

Työn teoriaosuudessa käsitellään lujia hitsattavia teräksiä sekä niiden hitsauksessa huomioitavia erityispiirteitä. Työssä esitellään hitsattavuuden arviointiin kehitettyjä teoreettisia menetelmiä sekä otetaan kantaa hitsauksen suoritustekniikkaan ja lisäainevalintaan. Myös lujien terästen hitsauksessa tyypilliset hitsausvirheet on käsitelty tässä työssä. Työn kokeellisessa osassa selvitettiin metsäteknologian tuotteita valmistavan metalliyrityksen käyttämien lujien terästen hitsattavuus ja hitsauksen esivalmistelujen tarpeellisuus. Kokeelliseen osioon kuului myös sopivan lisäainelangan valinta sekä tarkempaan tarkasteluun valitun esimerkkituotteen hitsien laadun selvittäminen. Tutkimuksissa käytettyjä menetelmiä olivat makro- ja mikrohietutkimus, hitsausliitoksen poikittainen vetokoe, Vickersin kovuuskoe ja murtokoe. Tarkasteluissa peilautuu myös hitsauksen automatisoinnin vaikutukset lujien terästen hitsaukseen. Kokeellisessa osiossa huomattiin nuorrutettujen terästen pehmeneminen liian suurella lämmöntuonnilla. Termomekaanisesti valssatut teräkset ovat paremmin hitsattavissa kuin nuorrutetut ja karkaistut teräkset. Kyseessä olevassa yrityksessä hitsattavien materiaalien paksuudet ovat pääsääntöisesti niin ohuita, ettei korotettua työlämpötilaa tarvita. Alilujat lisäaineet soveltuvat hitsauslisäaineeksi tuotantokäyttöön muutamia tuotekohtaisia poikkeuksia lukuun ottamatta.

Late Major Hemoptysis After Lung Volume Reduction With Coils Induced by Dual Antiaggregation Therapy.

Lung-volume reduction using coils is an effective and safe treatment for selected patients presenting severe emphysema and hyperinflation. Most complications occur during the first 30 days after the procedure. Although frequent, hemoptysis is usually transient and minor. Antiaggregation therapy is common in patients with emphysema who, very often, have additional tobacco-associated comorbidities. Aspirin is considered safe for most major interventions; however, clopidogrel is mainly contraindicated and considered an exclusion criterion. We present a case of life-threatening hemoptysis caused by dual antiaggregation therapy "accidentally" introduced 3 months after the procedure. So far no recommendations exist on the optimal therapeutic strategy after lung-volume reduction with coils.

Autoevaluación del aprendizaje en enfermería con ejercicios interactivos del programa Hot Potatoes

Los ejercicios interactivos de autoevaluación son una herramienta muy útil para fomentar el aprendizaje autónomo del estudiante. El programa Hot Potatoes permite el diseño de actividades interactivas para la evaluación formativa, con la incorporación de un sistema de retroacción que refuerza los contenidos no asimilados cuando la respuesta no es correcta. El objetivo de estudio es averiguar la opinión de los estudiantes sobre la utilización del programa Hot Potatoes. Materiales y métodos: Estudio descriptivo transversal en la promoción 2006-2007 de la asignatura Enfermería Maternal II. Los datos se recogieron a través de un cuestionario diseñado ad hoc. Resultados: Los ejercicios mejor valorados y considerados de menor dificultad fueron los de opción múltiple; los más difíciles fueron los textos desordenados y los ejercicios de rellenar huecos. Todos los estudiantes consideraron que el método motivó su interés por la asignatura y facilitó su aprendizaje. El 71% considera que el método le ha servido para adquirir conocimientos y ha sido muy útil como herramienta de estudio. Los aspectos que consideran más interesantes incluyen que: son un método de repaso y estudio, facilitan el aprendizaje de una forma amena y permiten conocer el nivel de conocimientos y corregir los errores durante el aprendizaje. Entre los aspectos que mejorarían destacan que incluirían más ejercicios y un número de preguntas más elevado. Conclusiones: El método ha tenido una buena aceptación y ha fomentado el aprendizaje autónomo. Consideramos que se trata de una estrategia de autoevaluación adecuada para la adaptación a los nuevos créditos europeos (ECTS).

Autoevaluación del aprendizaje en enfermería con ejercicios interactivos del programa Hot Potatoes

Los ejercicios interactivos de autoevaluación son una herramienta muy útil para fomentar el aprendizaje autónomo del estudiante. El programa Hot Potatoes permite el diseño de actividades interactivas para la evaluación formativa, con la incorporación de un sistema de retroacción que refuerza los contenidos no asimilados cuando la respuesta no es correcta. El objetivo de estudio es averiguar la opinión de los estudiantes sobre la utilización del programa Hot Potatoes. Materiales y métodos: Estudio descriptivo transversal en la promoción 2006-2007 de la asignatura Enfermería Maternal II. Los datos se recogieron a través de un cuestionario diseñado ad hoc. Resultados: Los ejercicios mejor valorados y considerados de menor dificultad fueron los de opción múltiple; los más difíciles fueron los textos desordenados y los ejercicios de rellenar huecos. Todos los estudiantes consideraron que el método motivó su interés por la asignatura y facilitó su aprendizaje. El 71% considera que el método le ha servido para adquirir conocimientos y ha sido muy útil como herramienta de estudio. Los aspectos que consideran más interesantes incluyen que: son un método de repaso y estudio, facilitan el aprendizaje de una forma amena y permiten conocer el nivel de conocimientos y corregir los errores durante el aprendizaje. Entre los aspectos que mejorarían destacan que incluirían más ejercicios y un número de preguntas más elevado. Conclusiones: El método ha tenido una buena aceptación y ha fomentado el aprendizaje autónomo. Consideramos que se trata de una estrategia de autoevaluación adecuada para la adaptación a los nuevos créditos europeos (ECTS).

Running mechanical alterations during repeated treadmill sprints in hot versus hypoxic environments : a pilot study.

We determined if performance and mechanical running alterations during repeated treadmill sprinting differ between severely hot and hypoxic environments. Six male recreational sportsmen (team- and racket-sport background) performed five 5-s sprints with 25-s recovery on an instrumented treadmill, allowing the continuous (step-by-step) measurement of running kinetics/kinematics and spring-mass characteristics. These were randomly conducted in control (CON; 25°C/45% RH, inspired fraction of oxygen = 20.9%), hot (HOT; 38°C/21% RH, inspired fraction of oxygen = 20.9%; end-exercise core temperature: ~38.6°C) and normobaric hypoxic (HYP, 25°C/45% RH, inspired fraction of oxygen = 13.3%/simulated altitude of ~3600 m; end-exercise pulse oxygen saturation: ~84%) environments. Running distance was lower (P < 0.05) in HOT compared to CON and HYP for the first sprint but larger (P < 0.05) sprint decrement score occurred in HYP versus HOT and CON. Compared to CON, the cumulated distance covered over the five sprints was lower (P < 0.01) in HYP but not in HOT. Irrespective of the environmental condition, significant changes occurred from the first to the fifth sprint repetitions (all three conditions compounded) in selected running kinetics (mean horizontal forces, P < 0.01) or kinematics (contact and swing times, both P < 0.001; step frequency, P < 0.001) and spring-mass characteristics (vertical stiffness, P < 0.001; leg stiffness, P < 0.01). No significant interaction between sprint number and condition was found for any mechanical data. Preliminary evidence indicates that repeated-sprint ability is more impaired in hypoxia than in a hot environment, when compared to a control condition. However, as sprints are repeated, mechanical alterations appear not to be exacerbated in severe (heat, hypoxia) environmental conditions.

Spiders on a Hot Volcanic Roof: Colonisation Pathways and Phylogeography of the Canary Islands Endemic Trap-Door Spider Titanidiops canariensis (Araneae, Idiopidae)

Studies conducted on volcanic islands have greatly contributed to our current understanding of how organisms diversify. The Canary Islands archipelago, located northwest of the coast of northern Africa, harbours a large number of endemic taxa. Because of their low vagility, mygalomorph spiders are usually absent from oceanic islands. The spider Titanidiops canariensis, which inhabits the easternmost islands of the archipelago, constitutes an exception to this rule. Here, we use a multi-locus approach that combines three mitochondrial and four nuclear genes to investigate the origins and phylogeography of this remarkable trap-door spider. We provide a timeframe for the colonisation of the Canary Islands using two alternative approaches: concatenation and species tree inference in a Bayesian relaxed clock framework. Additionally, we investigate the existence of cryptic species on the islands by means of a Bayesian multi-locus species delimitation method. Our results indicate that T. canariensis colonised the Canary Islands once, most likely during the Miocene, although discrepancies between the timeframes from different approaches make the exact timing uncertain. A complex evolutionary history for the species in the archipelago is revealed, which involves two independent colonisations of Fuerteventura from the ancestral range of T. canariensis in northern Lanzarote and a possible back colonisation of southern Lanzarote. The data further corroborate a previously proposed volcanic refugium, highlighting the impact of the dynamic volcanic history of the island on the phylogeographic patterns of the endemic taxa. T. canariensis includes at least two different species, one inhabiting the Jandia peninsula and central Fuerteventura and one spanning from central Fuerteventura to Lanzarote. Our data suggest that the extant northern African Titanidiops lineages may have expanded to the region after the islands were colonised and, hence, are not the source of colonisation. In addition, T. maroccanus may harbour several cryptic species.

Determining risk potential through accidents and near-accidents: an empirical study in a steel factory

Fatal and permanently disabling accidents form only one per I cent of all occupational accidents but in many branches of industry they account for more than half the accident costs. Furthermore the human suffering of the victim and his family is greater in severe accidents than in slight ones. For both human and economic reasons the severe accident risks should be identified befor injuries occur. It is for this purpose that different safety analysis methods have been developed . This study shows two new possible approaches to the problem.. The first is the hypothesis that it is possible to estimate the potential severity of accidents independent of the actual severity. The second is the hypothesis that when workers are also asked to report near accidents, they are particularly prone to report potentially severe near accidents on the basis of their own subjective risk assessment. A field study was carried out in a steel factory. The results supported both the hypotheses. The reliability and the validity of post incident estimates of an accident's potential severity were reasonable. About 10 % of accidents were estimated to be potentially critical; they could have led to death or very severe permanent disability. Reported near accidents were significantly more severe, about 60 $ of them were estimated to be critical. Furthermore the validity of workers subjective risk assessment, manifested in the near accident reports, proved to be reasonable. The studied new methods require further development and testing. They could be used both in routine usage in work places and in research for identifying and setting the priorities of accident risks.

Commodity Price Driven Risk Management from Viewpoint of High Grade Steel Alloys

The study of price risk management concerning high grade steel alloys and their components was conducted. This study was focused in metal commodities, of which nickel, chrome and molybdenum were in a central role. Also possible hedging instruments and strategies for referred metals were studied. In the literature part main themes are price formation of Ni, Cr and Mo, the functioning of metal exchanges and main hedging instruments for metal commodities. This section also covers how micro and macro variables may affect metal prices from the viewpoint of short as well as longer time period. The experimental part consists of three sections. In the first part, multiple regression model with seven explanatory variables was constructed to describe price behavior of nickel. Results were compared after this with information created with comparable simple regression model. Additionally, long time mean price reversion of nickel was studied. In the second part, theoretical price of CF8M alloy was studied by using nickel, ferro-chrome and ferro-molybdenum as explanatory variables. In the last section, cross hedging possibilities for illiquid FeCr -metal was studied with five LME futures. Also this section covers new information concerning possible forthcoming molybdenum future contracts as well. The results of this study confirm, that linear regression models which are based on the assumption of market rationality, are not able to reliably describe price development of metals at issue. Models fulfilling assumptions for linear regression may though include useful information of statistical significant variables which have effect on metal prices. According to the experimental part, short futures were found to incorporate the most accurate information concerning the price movements in the future. However, not even 3M futures were able to predict turning point in the market before the faced slump. Cross hedging seemed to be very doubtful risk management strategy for illiquid metals, because correlations coefficients were found to be very sensitive for the chosen time span.

Engendering Group Support Based Foresight for Capital Intensive Manufacturing Industries - Case Paper and Steel Industry Scenarios by 2018

In recent times of global turmoil, the need for uncertainty management has become ever momentous. The need for enhanced foresight especially concerns capital-intensive industries, which need to commit their resources and assets with long-term planning horizons. Scenario planning has been acknowledged to have many virtues - and limitations - concerning the mapping of the future and illustrating the alternative development paths. The present study has been initiated to address both the need of improved foresight in two capital-intensive industries, i.e. the paper and steel industries and the imperfections in the current scenario practice. The research problem has been approached by engendering a problem-solving vehicle, which combines, e.g. elements of generic scenario process, face-to-face group support methods, deductive scenario reasoning and causal mapping into a fully integrated scenario process. The process, called the SAGES scenario framework, has been empirically tested by creating alternative futures for two capital-intensive industries, i.e. the paper and steel industries. Three scenarios for each industry have been engendered together with the identification of the key megatrends, the most important foreign investment determinants, key future drivers and leading indicators for the materialisation of the scenarios. The empirical results revealed a two-fold outlook for the paper industry, while the steel industry future was seen as much more positive. The research found support for utilising group support systems in scenario and strategic planning context with some limitations. Key perceived benefits include high time-efficiency, productivity and lower resource-intensiveness. Group support also seems to enhance participant satisfaction, encourage innovative thinking and provide the users with personalised qualitative scenarios.

Els Hot Five : Louis Armstrong, l'avantguardista

Els objectius d’aquest treball són: reivindicar la faceta de Louis Armstrong com a músic al capdavant de l’avantguarda musical dels anys vint als Estats Units, analitzar les claus per entendre el seu ascens a la fama a partir dels anys trenta i valorar la seva contribució a la història de la música afroamericana. El cos del treball consta de dues parts: la primera, una biografia de l’artista per esbossar el seu context històric i el seu perfil psicològic; i la segona, que és el centre del treball, una anàlisi de les peces Savoy Blues, Cornet Chop Suey i Gully Low Blues, totes elles pertanyents al període dels Hot Five (1925-1929).