Influência das etapas do processo de abate de suínos na prevalência de patógenos e níveis de microrganismos indicadores de qualidade e higiene

The pig slaughter process involve different steps that can influence the microbiological quality of carcasses. At this, the understanding of the slaughter process on the microbiological aspects is necessary for the implementation and evaluation of critical control points. The microbiological control of the slaughter process should involve the evaluation of pathogens prevalence and levels of quality and hygiene indicator microorganisms. This study aimed at investigating the influence of steps slaughter process on the microbiological levels of pig carcasses, and evaluate if there is correlation between pathogens (Salmonella spp. and Listeria monocytogenes) and indicators (aerobic mesophilic counts, total coliforms, Escherichia coli and Enterobacteriaceae) microorganisms. A high Salmonella soroprevalence in pigs were founded before the slaughter (57.49 %). While the Salmonella prevalence in carcasses at the initial stage of the slaughter was 26.67 % and in the final stage 1.11 %, L. monocytogenes was detected only in the final washing and cooling steps, with a prevalence of 21.11 and 8.89 %, respectively. The aerobic mesophilic counts, Enterobacteriaceae, total coliforms and E. coli levels in initial steps of slaughter process were 4.25 ± 0.37; 1.25 ± 0.38; 1.10 ± 0.35 and 0.86 ± 0.36, respectively. At the end of slaughter process the results were lower (ranging from 0.16 at 2.70 log CFU/cm2). The step that most reduced microbiological levels was the scalding. The dehairing was a critical step that led to a significant increase of microorganisms levels in the process (p < 0.05). The evisceration not proved to be a critical step on the increase of microbial levels, differently of the final washing, which showed significant increases (p < 0.05) over the levels of aerobic counts, total coliforms, E. coli and enterobacterias (0.30; 0.36; 0.27 and 0.42 log respectively) and Salmonella spp. and L. monocytogenes. The chilling contributes significantly to the reduction of microbiological levels of carcasses, bringing them to levels below the all process stages, with the exception of scalding. No correlation between the hygiene indicator microorganisms used and presence of Salmonella spp. and L. monocytogenes were obtained (p < 0.05). The results show that steps in the process are critical to the sanitary profile, which implies the need to implement actions in the process to reducing the microbiological levels.

Determinação de curva glicolítica em carcaças de aves PSE (Pale, soft, exsudative) e normal em linha de abate industrial

Some quality defects can cause changes in attributes of the meat, among these we can detach the PSE meat (Pale, Soft and Exudative). The PSE meat is pale, flaccid and exudative and result from sudden pH decrease while the carcass is still under high temperature. The identification of PSE meat has been done by measuring pH and L* (Lightness). However, studies suggest that a more precise evaluation of the kinetics of pH and temperature decrease has to be conducted to better understand the etiology of PSE meat in poultry. The aim of this study was to obtain the glycolytic curve for normal and PSE meat of chicken, through the pH, L* and CRA (water holding capacity) analysis. This experiment was conducted with carcasses obtained from a commercial slaughterhouse (n = 35) of Cobb lineage, 50 days old, from the same batch of creation and with the same pre-slaughter fasting time (10h). Samples of breast fillets were obtained from carcasses randomly collected immediately at the output of pre-cooling chiller, and the analysis of pH, temperature and L * were conducted in the same in times 1h35, 2h35, 3h35, 5h35, 8h35, 11h35, 14h35, 17h35, 20h35, 23h35 and 25h35 post mortem. The CRA analyzes were performed at the time of 25h35 post mortem. The pH measurements indicated that only from the 04 time (8h35 post mortem) was possible to verify an indicative of stabilization, being that PSE meat pH was 5,69±0,07, and normal meat was 5,93±0,09. The final pH (25h35 post mortem) was 5,98±0,06 and L* 57,30± 2,39 for normal meat, while for PSE meat the result was 5,72±0,06 and L* 59,44±1,51. To CRA, the average of the samples (67,19±3.13 and 64,45± 2.66) showed a difference between the normal chicken fillets and PSE respectively. The data found in this study are consistent with those reported by own research group in another slaughterhouse and contradicts similar works, but made at room temperature, indicating that for chickens under commercial conditions the resolution of rigor mortis occurs after 8h35 post mortem.

Avaliação da anchoita (engraulis anchoita) salgada maturada acondicionada em atmosfera modificada

A anchoita foi capturada e acondicionada a bordo sob-resfriamento a 0°C com gelo em escamas. Após o recebimento, o pescado foi processado na forma salgado-maturado. Após a maturação foram processadas e embaladas em sacos de polietileno e armazenadas sob-refrigeração a 5°C durante 84 dias. As amostras foram divididas grupos: (1) sob pressão atmosfera normal, (2) vácuo, (3) atmosfera modificada com 50% CO2 + 20% O2 + 30% N2 e (4) 60% CO2 + 10% O2 + 30% N2, em embalagens de polietileno e aluminizadas, termo-seladas e armazenadas sob-refrigeração a 5°C. Os valores de textura tiveram uma redução de 2277,8 N (Kg.m/s2 ) para 821,90 N (Kg.m/s2 ) para o tratamento controle. A qualidade inicial do pescado atendeu aos padrões legais vigentes, apresentando ausência Salmonella sp e enumerações aceitáveis aos padrões de Staphylococcus coagulase positiva, Clostridium sulfito redutores, coliforme totais e a 45ºC. Com relação ao pH, houve diferenças significativas durante o tempo de processamento (p<0,05), o valor passou de 6,3 (início) para 6,4 (final). Com relação aos resultados correspondentes aos parâmetros L*, a* e b* (cor), em todos os tratamentos e ao longo do tempo de processamento (ambas as embalagens), ocorreram diferenças significativas (p<0,05). Os valores de L* variaram de 34,80 para 18,00 (controle) 23,00 (vácuo), 20,21 (T3) e 22,00 (T4) embalagens de polietileno. Nas embalagens de alumínio os valores de L* variaram de 34,00 para 25,00 (controle), 29,00(vácuo), 22,10 (T3) e 26,00 (T4).

Influência de variáveis arquitetônicas no desempenho energético de hotéis no clima quente e úmido da cidade de Natal/RN

This master thesis aims to assess the influence of the design decisions on the energy building performance of hotels. The research is based on the integration of field study and computer simulation. Firstly, a detailed field study is carried out to identify the characteristics of hotels in Natal, Rio Grande do Norte. The items assessed are occupancies, light and equipment densities, types of air conditioning, total and monthly energy consumption, among others. A second and more comprehensive field study is carried out to identify the range of occurrence of architectural variables, with a larger number of buildings. A base case is modelled in VisualDOE, based on the first field study. Then, a first set of simulations are run to explore the sensitivity of the variables on the energy consumption. The results analyses were the base of a second set of simulations, which combined the most influential variables. The results of 384 models were assessed, and the impacts of design decisions were quantified. The study discusses tendencies and recommendations, as well as the methods advantages and disadvantages

Desacoplamento mitocondrial e estresse oxidativo em espermatozoides suínos resfriados

A espécie suína (Sus scropha domesticus) possui relevância nos âmbitos da pesquisa, da xenotransplantação e da produção de carnes. O resfriamento de sêmen é capaz de reduzir o metabolismo celular e possibilitar o armazenamento dos gametas, sendo auxiliar durante práticas de reprodução assistida. Contudo, os espermatozoides suínos são sensíveis ao estresse oxidativo gerado durante o processo de resfriamento. O 2,4 dinitrofenol (DNP) poderia gerar o desacoplamento mitocondrial reduzindo o estresse oxidativo e prolongando indiretamente a viabilidade e capacidade fertilizante de espermatozoides suínos resfriados pela diminuição de espécies reativas de oxigênio. O objetivo do presente estudo foi avaliar os efeitos do desacoplamento mitocondrial induzido pelo DNP e os efeitos desse desacoplamento sobre as de fluidez e integridade de membrana plasmática, funcionalidade de mitocôndria, motilidade espermática, além dos parâmetros de estresse oxidativo de lipoperoxidação e produção de espécies reativas de oxigênio, durante o resfriamento a 17 °C de 24 até 96 horas. Utilizou-se 22 ejaculados expostos ao diluente Betsville Thawing Solution (BTS) (controle) e ao mesmo diluente acrescido das concentrações de 0,01 µM (T1); 0,1 µM (T2); 1,0 µM (T3) e 10 µM (T4) de DNP. Através do teste de Shapiro-Wilk as variáveis que não apresentaram normalidade, tiveram suas médias comparadas pelo teste de KruskalWallis. As análises estatísticas demonstraram que o DNP não se diferiu do controle independente do tempo de armazenamento, para nenhuma das variáveis analisadas. Possivelmente, a falta de ação sobre as mitocôndrias, ou seja, a não promoção do desacoplamento mitocondrial foi o motivo principal para a falta dos efeitos do DNP. Acredita-se que a utilização do DNP em temperaturas mais elevadas por estas promoverem aumento da fluidez de membrana e/ou o aumento das concentrações de DNP poderiam gerar efeitos significativos sobre as mitocôndrias e demais variáveis analisadas. Finalmente, o DNP nas concentrações testadas não se diferiu do controle em todas as variáveis analisadas independente do tempo de armazenamento.

Características bioquímicas da carne de bubalinos Mediterrâneo terminados em confinamento e abatidos em diferentes pesos

Este trabalho teve como objetivo avaliar as características bioquímicas da carne de bubalinos Mediterrâneo terminados em confinamento e abatidos em diferentes pesos. Foram utilizados 28 bubalinos Mediterrâneo jovens, com idade de 9 meses, e peso vivo médio inicial de 240kg. Os animais foram alimentados com ração total à vontade em regime de confinamento até atingirem pesos de abate de 450, 480, 510 e 540kg de peso vivo (tratamentos). Os valores de pH e temperatura dos músculos Longissimus dorsi e Bíceps femoris foram coletados a intervalos de duas horas durante 24 horas após o abate. Determinou-se a cor da carne pelos métodos subjetivo e objetivo. Não houve efeito de interação entre tratamento e tempo de coleta. Não houve diferença significativa entre os tratamentos em relação ao pH e à temperatura nos dois músculos estudados (Longissimus dorsi e Bíceps femoris) durante o processo de resfriamento das carcaças. Os valores médios de pH inicial e pH final dos músculos Longissimus dorsi e Bíceps femoris foram de 6,6 e 5,4; e de 6,3 e 5,5, respectivamente. Os valores médios de temperatura inicial e final dos músculos Longissimus dorsi e Bíceps femoris foram 39,7°C e 4,1°C; 40,4°C e 7,0°C, respectivamente. Quanto à cor da carne, pelo método subjetivo, não houve diferença significativa entre os tratamentos estudados, obtendo-se a média geral de 3,41 pontos. em relação à cor da carne pelo método objetivo, não houve diferença significativa entre os tratamentos estudados. Os valores médios encontrados foram : L*= 35,16; a*=12,43 e b*=5,29. A carne bubalina, apesar de se apresentar mais escura que a carne bovina, não traz prejuízos quanto ao aspecto visual para o consumidor.

Geologia, petrologia, geocronologia e mineralizações sulfetadas do complexo ézio, província mineral de carajás, Brasil

Dissertação (mestrado)—Universidade de Brasília, Instituto de Geociências, Pós-Graduação em Geologia, 2015.

Estudo sobre o efeito dos parâmetros de processamento dos pós e sinterização do aço inox 316l reforçado com NbC

This masther dissertation presents a contribution to the study of 316L stainless steel sintering aiming to study their behavior in the milling process and the effect of isotherm temperature on the microstructure and mechanical properties. The 316L stainless steel is a widely used alloy for their high corrosion resistance property. However its application is limited by the low wear resistance consequence of its low hardness. In previous work we analyzed the effect of sintering additives as NbC and TaC. This study aims at deepening the understanding of sintering, analyzing the effect of grinding on particle size and microstructure and the effect of heating rate and soaking time on the sintered microstructure and on their microhardness. Were milled 316L powders with NbC at 1, 5 and 24 hours respectively. Particulates were characterized by SEM and . Cylindrical samples height and diameter of 5.0 mm were compacted at 700 MPa. The sintering conditions were: heating rate 5, 10 and 15◦C/min, temperature 1000, 1100, 1200, 1290 and 1300◦C, and soaking times of 30 and 60min. The cooling rate was maintained at 25◦C/min. All samples were sintered in a vacuum furnace. The sintered microstructure were characterized by optical and electron microscopy as well as density and microhardness. It was observed that the milling process has an influence on sintering, as well as temperature. The major effect was caused by firing temperature, followed by the grinding and heating rate. In this case, the highest rates correspond to higher sintering.

Estudo da sinterização de cavacos de aço ferritico

This research studies the sintering of ferritic steel chips from the machining process. Were sintered metal powder obtained from machining process chips for face milling of a ferritic steel. The chip was produced by machining and characterized by SEM and EDS, and underwent a process of high energy mill powder characterized also by SEM and EDS. Were constructed three types of matrixes for uniaxial compression (relation l / d greater than 2.5). The differences in the design of the matrixes were essentially in the direction of load application, which for cylindrical case axial direction, while for the rectangular arrays, the longer side. Two samples were compressed with different geometries, a cylindrical and rectangular with the same compaction pressure of 700 MPa. The samples were sintered in a vacuum resistive furnace, heating rate 20 °C / min., isotherm 1300 °C for 60 minutes, and cooling rate of 25 °C / min to room temperature. The starting material of the rectangular sample was further annealed up to temperature of 800 ° C for 30 min. Sintered samples were characterized by scanning electron microscopy, optical microscopy and EDS. The sample compressed in the cylindrical matrix did not show a regular density reflecting in the sintered microstructure revealed by the irregular geometry of the pores, characterizing that the sintering was not complete, reaching only the second phase. As for the specimen compacted in the rectangular array, the analysis performed by scanning electron microscopy, optical microscopy and EDS indicate a good densification, and homogeneous microstructure in their full extent. Additionally, the EDS analyzes indicate no significant changes in chemical composition in the process steps. Therefore, it is concluded that recycling of chips, from the processed ferritic steel is feasible by the powder metallurgy. It makes possible rationalize raw material and energy by manufacture of known properties components from chips generated by the machining process, being benefits to the environment

Estudo sobre a redução aluminotérmica de Ta2O5 e TiO2 usando descarga de cátodo oco

In this study it was used two metallic oxides, Ta2O5 and TiO2, in order to obtain metallic powders of Ta and Ti through aluminothermic reduction ignited by plasma. Ta2O5 and TiO2 powders were mixed with Al in a planetary mill, using different milling times. A thermal analysis study (DTA and TG) was carried out, in order to know the temperature to react both the mixtures. Then, these mixtures were submitted to a hollow cathode discharge, where they were reacted using aluminothermic reduction ignited by plasma. The product obtained was characterized by XRD and SEM, where it was proven the possibility of producing these metallic particles, different from the conventional process, where metallic ingots are obtained. It was verified that the aluminothermic reduction ignited by plasma is able to produce metallic powders of Ta and Ti, and a higher efficiency was observed to the process with Ta2O5-Al mixtures. Among different microstructural aspects observed, it can be noted the presence of metallic nanoparticles trapped into an Al2O3 matrix, besides acicular structures (titanium) and dendritic structures (tantalum), which are a product characteristic from a fast cooling

Interface entre arquitetura bioclimática e decisões projetuais

This research has as its object study focus bioclimatic in architecture and its conection with projects decisions, on what regards to environmental comfort for single-family dwelling. From the analysis of five architectural projects inserted in Natal/RN, warm-moist weather, this research gather informations regarding architectural features guided by shape and space arrengement, which embody important elements for the project design development. Computer simulations assisted as foundation to verify the efficiency grade for these projects strategies from shading analysis. Related strategies for the demands of natural ventilation circulation and thermal mass for refrigeration were analysed as well. Results show that there is an hierarchizing of priorities for the decisions made when it comes to shape and space disposition variables, as well as the way these variables will consider the bioclimatic demands. The analysis, even, show that there is no single way to respond to specific bioclimatic demands, as it points out the value of examination of the projectual solutions throughtout the conception process, in order to achieve an efficient project performance for the envimonment comfort

Redução aluminotérmica do óxido de tântalo usando uma tocha de plasma como ignitor

In this work was used a plasma torch of non transferred arc with argon as work gas, using a power supply with maximum DC current of 250 A and voltage of 30 V to activate the plasma and keep it switched on. The flame temperature was characterized by optical emission spectroscopy, through Boltzmann-plot-method. The torch has been used like igniter in the aluminothermic reduction of the mixture tantalum oxide and aluminum, seeking to obtain metallic tantalum. In heating of the reagents only one particle will be considered to study interactions between plasma-particle, seeking to determinate its fusion and residence time. The early powders were characterized by laser granulometry, scanning electron microscopy (SEM) and X-ray diffraction analysis. The final product of this reaction was characterized by SEM and X-ray diffraction. Crystallite size was calculated by the Scherrer equation and microdeformation was determined using Willamsom-Hall graph. With Rietveld method was possible to quantify the percentile in weight of the products obtained in the aluminothermic reaction. Semi-quantitative chemical analysis (EDS) confirmed the presence of metallic tantalum and Al2O3 as products of the reduction. As was waited the particle size of the metallic tantalum produced, presents values in nanometric scale due the short cooling time of those particles during the process

Influência de variáveis arquitetônicas no desempenho energético de hotéis no clima quente e úmido da cidade de Natal/RN

This master thesis aims to assess the influence of the design decisions on the energy building performance of hotels. The research is based on the integration of field study and computer simulation. Firstly, a detailed field study is carried out to identify the characteristics of hotels in Natal, Rio Grande do Norte. The items assessed are occupancies, light and equipment densities, types of air conditioning, total and monthly energy consumption, among others. A second and more comprehensive field study is carried out to identify the range of occurrence of architectural variables, with a larger number of buildings. A base case is modelled in VisualDOE, based on the first field study. Then, a first set of simulations are run to explore the sensitivity of the variables on the energy consumption. The results analyses were the base of a second set of simulations, which combined the most influential variables. The results of 384 models were assessed, and the impacts of design decisions were quantified. The study discusses tendencies and recommendations, as well as the methods advantages and disadvantages

Inibição do crescimento micelial de Sclerotinia sclerotiorum por filtrados de Trichoderma sp. e Clonostachys rosea.

Uma alternativa para controle do mofo-branco do feijão (Sclerotinia sclerotiorum, Ss) é o uso de agentes de controle biológico (ACB). Trichoderma sp. (Tr) e Clonostachys rosea (Cr) podem competir, parasitar e produzir metabólitos tóxicos contra fitopatógenos. Avaliou-se a capacidade de três isolados de Tr e um de Cr, previamente selecionados para o controle de Ss, em produzir metabólitos tóxicos contra o patógeno. Os ACB foram crescidos em caldo batata dextrose sob agitação (100 rpm) por sete dias. Após, o caldo foi filtrado a vácuo (membrana bacteriológica 0,22µm) e adicionou-se uma alíquota (2 ml) do filtrado ou de ADE (testemunha) a BDA fundente em placas de Petri. Após o resfriamento, adicionou-se no centro da placa um disco de micélio de Ss. As placas (cinco repetições/tratamento) foram incubadas a 20˚C ou 25˚C. Diariamente mediu-se o diâmetro das colônias até a testemunha atingir as bordas da placa. A 25˚C verificou-se significativa redução (Tukey, 5%) do crescimento micelial de Ss pelos filtrados dos três isolados de Tr (72 a 79%) e por Cr (50%). A 20ºC, apenas dois isolados de Tr inibiram Ss (45 a 65%). Os resultados indicam que os ACB podem atuar por antibiose, porém a eficiência é influenciada pelo ambiente.

Hidrolisado de proteína de soja em meio de cultivo para a produção de agente de controle biológico.

Os produtos de controle biológico devem ser produzidos com custo competitivo em relação aos sintéticos para que seu uso se torne generalizado. A fermentação é uma das etapas mais caras para o escalonamento da produção por causa do valor dos ingredientes dos meios de cultura. Neste trabalho, Pichia kudriavzevii L9, um agente de controle de podridão pós-colheita de frutas, foi utilizada como modelo para a avaliação de hidrolisado de proteína de soja como fonte de nitrogênio em meio de cultura líquido. Foram testadas cinco concentrações de proteína de soja (50 L-1 a 250 g L-1) em solução aquosa contendo concentrações de H2SO4 de 0 a 1,0 N, tratadas em autoclave a 121 ºC e 1,0 atm de pressão. Após o resfriamento, o produto obtido foi alcalinizado com KOH até atingir o pH de 6,0 ? 7,0. Nas condições do experimento, a melhor condição para a hidrólise do proteinato de soja e obtenção de maior concentração de aminoácidos no meio, foi de 200 g L-1 de proteinato em solução de HCl 0,5 N, produzindo 32,1 g L-1 de aminoácido livre, quantificado pelo método da ninhidrina. O hidrolisado foi utilizado para o crescimento de P. kudriavzevii L9, obtendo-se a maior produtividade de células viáveis de levedura com a adição de 2% do hidrolisado obtido no meio de cultura, na faixa entre 0,2 a 0,5 N de HCL.