Optimization of friction stir welding parameters for dissimilar aluminum alloys

Assembly consisting of cast and wrought aluminum alloys has wide spread application in defense and aero space industries. For the efficacious use of the transition joints, the weld should have adequate strength and formability. In the present investigation, A356 and 6061 aluminum alloys were friction stir welded under tool rotational speed of 1000-1400 rpm and traversing speed of 80-240 mm/min, keeping other parameters same. The variable process window is responsible for the change in total heat input and cooling rate during welding. Structural characterization of the bonded assemblies exhibits recovery-recrystallization in the stirring zone and breaking of coarse eutectic network of Al-Si. Dispersion of fine Si rich particles, refinement of 6061 grain size, low residual stress level and high defect density within weld nugget contribute towards the improvement in bond strength. Lower will be the tool rotational and traversing speed, more dominant will be the above phenomena. Therefore, the joint fabricated using lowest tool traversing and rotational speed, exhibits substantial improvement in bond strength (similar to 98% of that of 6061 alloy), which is also maximum with respect to others. (C) 2010 Elsevier Ltd. All rights reserved.

Sequential split vector quantization of LSF parameters using conditional PDF

A better performing product code vector quantization (VQ) method is proposed for coding the line spectrum frequency (LSF) parameters; the method is referred to as sequential split vector quantization (SeSVQ). The split sub-vectors of the full LSF vector are quantized in sequence and thus uses conditional distribution derived from the previous quantized sub-vectors. Unlike the traditional split vector quantization (SVQ) method, SeSVQ exploits the inter sub-vector correlation and thus provides improved rate-distortion performance, but at the expense of higher memory. We investigate the quantization performance of SeSVQ over traditional SVQ and transform domain split VQ (TrSVQ) methods. Compared to SVQ, SeSVQ saves 1 bit and nearly 3 bits, for telephone-band and wide-band speech coding applications respectively.

Physicochemical, spectroscopic and electrochemical characterization of magnesium ion-conducting, room temperature, ternary molten electrolytes

Room temperature, magnesium ion-conducting molten electrolytes are prepared using a combination of acetamide, urea and magnesium triflate or magnesium perchlorate. The molten liquids show high ionic conductivity, of the order of mS cm(-1) at 298 K. Vibrational spectroscopic studies based on triflate/perchlorate bands reveal that the free ion concentration is higher than that of ion-pairs and aggregates in the melt. Electrochemical reversibility of magnesium deposition and dissolution is demonstrated using cyclic voltammetry and impedance studies. The transport number of Mg2+ ion determined by means of a combination of d.c. and ac. techniques is similar to 0.40. Preliminary studies on the battery characteristics reveal good capacity for the magnesium rechargeable cell and open up the possibility of using this unique class of acetamide-based room temperature molten electrolytes in secondary magnesium batteries. (C) 2010 Elsevier B.V. All rights reserved.

Physicochemical studies on the gelation of hen egg yolk; separation of gelling protein components from yolk plasma

A study of the component(s) in egg yolk responsible for gelation of yolk on freezing and thawing has shown that granule-free yolk plasma, obtained by high-speed centrifugation of yolk, has the capacity to gel. As with the whole yolk, gelation of yolk plasma on freezing and thawing could be inhibited by additives such as sugars, sodium chloride, proteolytic enzymes, and phospholipase-A. Phospholipase-C, which induces gelation of whole yolk at room temperature, has a similar effect on yolk plasma. Yolk plasma has been separated into aggregating (gelling) and soluble fractions by delipidation, using formic acid. Each of these fractions consists of three or four protein components, as observed by gel filtration, ultracentrifugation, and agar electrophoresis. The proteins are glycoproteins and contain bound hexoses, hexosamine, and sialic acid. The gelation of yolk has been attributed to the interactions between protein molecules following disruption of lipid-protein bonds.

Determination of the orthotropic plate parameters of stiffened plates and grillages in free vibration

It is well known that the analysis of vibration of orthogonally stiffened rectangular plates and grillages may be simplified by replacing the actual structure by an orthotropic plate. This needs a suitable determination of the four elastic rigidity constants Dx, Dy, Dxy, D1 and the mass {Mathematical expression} of the orthotropic plate. A method is developed here for determining these parameters in terms of the sectional properties of the original plate-stiffener combination or the system of interconnected beams. Results of experimental work conducted on aluminium plates agree well with the results of the theory developed here.

ESR study of dibarium copper formate tetrahydrate Part II. Optical absorption and temperature dependence of spin-hamiltonian parameters

The variations in certain spin-Hamiltonian parameters of the Cu++ ion in dibarium copper formate tetrahydrate with temperature have been studied. Optical absorption investigations on single crystals of the salt at room temperature and 90° K. are reported. The results are discussed in terms of a model in which vibronic mixing of certain electron levels of the Cu++ ion play an important role.

Physicochemical studies on the gelation of hen's egg yolk: Delipidation of yolk plasma by treatment with phospholipase-C and extraction with solvents

A method for the delipidation of egg yolk plasma using phospholipase-C, n-heptane, and 1-butanol has been described. An aggregating protein fraction and a soluble protein fraction were separated by the action of phospholipase-C. The aggregating protein fraction freed of most of the lipids by treatment with n-heptane and 1-butanol was shown to be the apolipoproteins of yolk plasma, whereas the soluble proteins were identified as the livetins. Carbohydrate and the N-terminal amino acid analysis of these protein fractions are reported. A comparison of these protein fractions with the corresponding fractions obtained by formic acid delipidation of yolk plasma has been made. The gelation of yolk plasma by the action of phospholipase-C has been interpreted as an aggregation of lipoproteins caused by ionic interactions. The role of lecithin in maintaining the structural integrity of lipoproteins has been discussed.

Loading of itraconazole into porous silica and silicon microparticles: characterization and dissolution tests

Most new drug molecules discovered today suffer from poor bioavailability. Poor oral bioavailability results mainly from poor dissolution properties of hydrophobic drug molecules, because the drug dissolution is often the rate-limiting event of the drug’s absorption through the intestinal wall into the systemic circulation. During the last few years, the use of mesoporous silica and silicon particles as oral drug delivery vehicles has been widely studied, and there have been promising results of their suitability to enhance the physicochemical properties of poorly soluble drug molecules. Mesoporous silica and silicon particles can be used to enhance the solubility and dissolution rate of a drug by incorporating the drug inside the pores, which are only a few times larger than the drug molecules, and thus, breaking the crystalline structure into a disordered, amorphous form with better dissolution properties. Also, the high surface area of the mesoporous particles improves the dissolution rate of the incorporated drug. In addition, the mesoporous materials can also enhance the permeability of large, hydrophilic drug substances across biological barriers. T he loading process of drugs into silica and silicon mesopores is mainly based on the adsorption of drug molecules from a loading solution into the silica or silicon pore walls. There are several factors that affect the loading process: the surface area, the pore size, the total pore volume, the pore geometry and surface chemistry of the mesoporous material, as well as the chemical nature of the drugs and the solvents. Furthermore, both the pore and the surface structure of the particles also affect the drug release kinetics. In this study, the loading of itraconazole into mesoporous silica (Syloid AL-1 and Syloid 244) and silicon (TOPSi and TCPSi) microparticles was studied, as well as the release of itraconazole from the microparticles and its stability after loading. Itraconazole was selected for this study because of its highly hydrophobic and poorly soluble nature. Different mesoporous materials with different surface structures, pore volumes and surface areas were selected in order to evaluate the structural effect of the particles on the loading degree and dissolution behaviour of the drug using different loading parameters. The loaded particles were characterized with various analytical methods, and the drug release from the particles was assessed by in vitro dissolution tests. The results showed that the loaded drug was apparently in amorphous form after loading, and that the loading process did not alter the chemical structure of the silica or silicon surface. Both the mesoporous silica and silicon microparticles enhanced the solubility and dissolution rate of itraconazole. Moreover, the physicochemical properties of the particles and the loading procedure were shown to have an effect on the drug loading efficiency and drug release kinetics. Finally, the mesoporous silicon particles loaded with itraconazole were found to be unstable under stressed conditions (at 38 qC and 70 % relative humidity).

Genetic variation in the LDL receptor-related protein 5 (LRP5) gene : Association with bone health and metabolic parameters

Bone mass accrual and maintenance are regulated by a complex interplay between genetic and environmental factors. Recent studies have revealed an important role for the low-density lipoprotein receptor-related protein 5 (LRP5) in this process. The aim of this thesis study was to identify novel variants in the LRP5 gene and to further elucidate the association of LRP5 and its variants with various bone health related clinical characteristics. The results of our studies show that loss-of-function mutations in LRP5 cause severe osteoporosis not only in homozygous subjects but also in the carriers of these mutations, who have significantly reduced bone mineral density (BMD) and increased susceptibility to fractures. In addition, we demonstrated for the first time that a common polymorphic LRP5 variant (p.A1330V) was associated with reduced peak bone mass, an important determinant of BMD and osteoporosis in later life. The results from these two studies are concordant with results seen in other studies on LRP5 mutations and in association studies linking genetic variation in LRP5 with BMD and osteoporosis. Several rare LRP5 variants were identified in children with recurrent fractures. Sequencing and multiplex ligation-dependent probe amplification (MLPA) analyses revealed no disease-causing mutations or whole-exon deletions. Our findings from clinical assessments and family-based genotype-phenotype studies suggested that the rare LRP5 variants identified are not the definite cause of fractures in these children. Clinical assessments of our study subjects with LPR5 mutations revealed an unexpectedly high prevalence of impaired glucose tolerance and dyslipidaemia. Moreover, in subsequent studies we discovered that common polymorphic LRP5 variants are associated with unfavorable metabolic characteristics. Changes in lipid profile were already apparent in pre-pubertal children. These results, together with the findings from other studies, suggest an important role for LRP5 also in glucose and lipid metabolism. Our results underscore the important role of LRP5 not only in bone mass accrual and maintenance of skeletal health but also in glucose and lipid metabolism. The role of LRP5 in bone metabolism has long been studied, but further studies with larger study cohorts are still needed to evaluate the specific role of LRP5 variants as metabolic risk factors.

The connection between on-farm assessed welfare (A-index) and production parameters of the sows

Tämän tutkimuksen tavoitteena oli selvittää tilalla määritetyn hyvinvoinnin yhteyttä emakoiden tuotantotuloksiin. Hyvinvointia arvioitiin suomalaisen hyvinvointi-indeksin, A-indeksi, avulla. Tuotantotuloksina käytettiin kahta erilaista tuotosaineistoa, jotka molemmat pohjautuivat kansalliseen tuotosseuranta aineistoon. Hyvinvointimääritykset tehtiin 30 porsastuotantosikalassa maaliskuun 2007 aikana. A-indeksi koostuu kuudesta kategoriasta ’liikkumismahdollisuudet’, ’alustan ominaisuudet’, ’sosiaaliset kontaktit’, ’valo, ilma ja melu’, ’ruokinta ja veden saanti’ sekä ’eläinten terveys ja hoidon taso’. Jokaisessa kategoriassa on 3-10 pääosin ympäristöperäistä muuttujaa, jotka vaihtelevat osastoittain. Maksimipistemäärä osastolle on 100. Hyvinvointimittaukset tehtiin porsitus-, tiineytys- ja joutilasosastoilla. Erillisten tiineytysosastojen pienen lukumäärän takia (n=7) tilakohtaiset tiineytys- ja joutilasosastopisteet yhdistettiin ja keskiarvoja käytettiin analyyseissä. Yhteyksiä tuotokseen tutkittiin kahden eri aineiston avulla 1) Tilaraportti aineisto (n=29) muodostuu muokkaamattomista tila- ja tuotostuloksista tilavierailua edeltävän vuoden ajalta, 2) POTSIaineisto (n=30) muodostuu POTSI-ohjelmalla (MTT) muokatusta tuotantoaineistosta, joka sisältää managementtiryhmän (tila, vuosi, vuodenaika) vaikutuksen ensikoiden ja emakoiden pahnuekohtaiseen tuotokseen. Yhteyksiä analysointiin korrelaatio- ja regressioanalyysien avulla. Vaikka osallistuminen tutkimukseen oli vapaaehtoista, molempien tuotantoaineistojen perusteella tutkimustilat edustavat keskituottoista suomalaista sikatilaa. A-indeksin kokonaispisteet vaihtelivat välillä 37,5–64,0 porsitusosastolla ja 39,5–83,5 joutilasosastolla. Tilaraporttiaineistoa käytettäessä paremmat pisteet porsitusosaston ’eläinten terveys ja hoidon taso’ -kategoriasta lyhensivät eläinten lisääntymissykliä, lisäsivät syntyvien pahnueiden ja porsaiden määrää sekä alensivat kuolleena syntyneiden lukumäärää. Regressiomallin mukaan ’eläinten terveys ja hoidon taso’ -kategoria selitti syntyvien porsaiden lukumäärän, porsimisvälin pituuden sekä keskiporsimiskerran vaihtelua. Paremmat pisteet joutilasosaston ’liikkumismahdollisuudet’ kategoriasta alensivat syntyneiden pahnueiden sekä syntyneiden että vieroitettujen porsaiden lukumäärää. Regressiomallin mukaan ensikkopahnueiden osuus ja ”liikkumismahdollisuudet” kategorian pisteet selittivät vieroitettujen porsaiden lukumäärän vaihtelua. POTSI-aineiston yhteydessä kuolleena syntyneiden porsaiden lukumäärän aleneminen oli ensikoilla yhteydessä parempiin porsitusosaston ’sosiaalisiin kontakteihin’ ja emakoilla puolestaan joutilasosaston parempiin ’eläinten terveys ja hoidon taso’ pisteisiin. Kahden eri tuotantoaineiston avulla saadut tulokset erosivat toisistaan. Seuraavissa tutkimuksissa onkin suositeltavampaa käyttää Tilaraporttiaineistoja, joissa tuotokset ilmoitetaan vuosikohtaisina. Tämän tutkimuksen perusteella hyvinvoinnilla ja tuotoksella on yhteyksiä, joilla on myös merkittävää taloudellista vaikutusta. Erityisesti hyvä eläinten hoito ja eläinten terveys lisäävät tuotettujen porsaiden määrää ja lyhentävät lisääntymiskiertoa. Erityishuomiota tulee kiinnittää vapaana olevien joutilaiden emakoiden sosiaaliseen stressiin ja rehunsaannin varmistamiseen kaikille yksilöille.

ErbB-2 expression and its association with other biological parameters of breast cancer among Indian women

Overexpression of the epidermal growth factor receptor family genes, which include ErbB-1, 2, 3 and 4, has been implicated in a number of cancers. We have studied the extent of ErbB-2 overexpression among Indian women with sporadic breast cancer. Methods: Immmunohistochemistry and genomic polymerase chain reaction (PCR) were used to study the ErbB2 overexpression. ErbB2 status was correlated with other clinico-pathological parameters, including patient survival. Results: ErbB-2 overexpression was detected in 43.2% (159/368) of the cases by immunohistochemistry. For a sub-set of patients (n = 55) for whom total DNA was available, ErbB-2 gene amplification was detected in 25.5% (14/55) of the cases by genomic PCR. While the ErbB2 overexpression was significantly higher in patients with lymphnode (χ2 = 12.06, P≤ 0.001), larger tumor size (χ2 = 8.22, P = 0.042) and ductal carcinoma (χ2 = 15.42, P ≤ 0.001), it was lower in patients with disease-free survival (χ2 = 22.13, P ≤ 0.001). Survival analysis on a sub-set of patients for whom survival data were available (n = 179) revealed that ErbB-2 status (χ2 =25.94, P ≤ 0.001), lymphnode status (χ2 = 12.68, P ≤ 0.001), distant metastasis (χ2 = 19.49, P ≤ 0.001) and stage of the disease (χ2 = 28.04, P ≤0.001) were markers of poor prognosis. Conclusions: ErbB-2 overexpression was significantly greater compared with the Western literature, but comparable to other Indian studies. Significant correlation was found between ErbB-2 status and lymphnode status, tumor size and ductal carcinoma. ErbB-2 status, lymph node status, distant metastasis and stage of the disease were found to be prognostic indicators.

Apsidal motion in 4U 0115+63 and orbital parameters of 2S 1417-624 and V0332+53

Be/X-ray binary pulsars have wide eccentric orbits and hence the angle of periastron of the orbit is very well defined in these sources. The presence of an X-ray pulsar allows for accurate measurements of orbital elements. A Be star usually is a rapidly rotating star and hence will deviate from spherical geometry. The tidal interaction between the neutron star and the Be star will add to the distortion of the Be star and alter its mass distribution. Thus a measurable rate of apsidal motion is expected from these systems. In this paper, we present the first conclusive detection of apsidal motion of the binary 4U 0115+63. We also present new and accurate orbital parameters of the Be/X-ray binaries V0332+53 and 2S 1417-624.