Investigations of the scaling criteria for a mild combustion burner

In this paper, a new strategy for scaling burners based on "mild combustion" is evolved and adopted to scaling a burner from 3 to a 150 kW burner at a high heat release Late of 5 MW/m(3) Existing scaling methods (constant velocity, constant residence time, and Cole's procedure [Proc. Combust. Inst. 28 (2000) 1297]) are found to be inadequate for mild combustion burners. Constant velocity approach leads to reduced heat release rates at large sizes and constant residence time approach in unacceptable levels of pressure drop across the system. To achieve mild combustion at high heat release rates at all scales, a modified approach with high recirculation is adopted in the present studies. Major geometrical dimensions are scaled as D similar to Q(1/3) with an air injection velocity of similar to 100 m/s (Delta p similar to 600 mm water gauge). Using CFD support, the position of air injection holes is selected to enhance the recirculation rates. The precise role of secondary air is to increase the recirculation rates and burn LIP the residual CO in the downstream. Measurements of temperature and oxidizer concentrations inside 3 kW, 150 kW burner and a jet flame are used to distinguish the combustion process in these burners. The burner can be used for a wide range of fuels from LPG to producer gas as extremes. Up to 8 dB of noise level reduction is observed in comparison to the conventional combustion mode. Exhaust NO emissions below 26 and 3 ppm and temperatures 1710 and 1520 K were measured for LPG and producer gas when the burner is operated at stoichiometry. (c) 2004 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Disarming identities : Ethnic identities in conflict resolution: Hindrance or helpful resource?

This thesis proposes that national or ethnic identity is an important and overlooked resource in conflict resolution. Usually ethnic identity is seen both in international relations and in social psychology as something that fuels the conflict. Using grounded theory to analyze data from interactive problem-solving workshops between Palestinians and Israelis a theory about the role of national identity in turning conflict into protracted conflict is developed. Drawing upon research from, among others, social identity theory, just world theory and prejudice it is argued that national identity is a prime candidate to provide the justification of a conflict party’s goals and the dehumanization of the other necessary to make a conflict protracted. It is not the nature of national identity itself that lets it perform this role but rather the ability to mobilize a constituency for social action (see Stürmer, Simon, Loewy, & Jörger, 2003). Reicher & Hopkins (1996) have demonstrated that national identity is constructed by political entrepreneurs to further their cause, even if this construction is not a conscious one. Data from interactive problem-solving workshops suggest that the possibility of conflict resolution is actually seen by participants as a direct threat of annihilation. Understanding the investment necessary to make conflict protracted this reaction seems plausible. The justification for ones actions provided by national identity makes the conflict an integral part of a conflict party’s identity. Conflict resolution, it is argued, is therefore a threat to the very core of the current national identity. This may explain why so many peace agreements have failed to provide the hoped for resolution of conflict. But if national identity is being used in a constructionist way to attain political goals, a political project of conflict resolution, if it is conscious of the constructionist process, needs to develop a national identity that is independent of conflict and therefore able to accommodate conflict resolution. From this understanding it becomes clear why national identity needs to change, i.e. be disarmed, if conflict resolution is to be successful. This process of disarmament is theorized to be similar to the process of creating and sustaining protracted conflict. What shape and function this change should have is explored from the understanding of the role of national identity in supporting conflict. Ideas how track-two diplomacy efforts, such as the interactive problem-solving workshop, could integrate a process by both conflict parties to disarm their respective identities are developed.

Thermal ignition studies on metallized fuel-oxidizer systems

The thermal ignition behaviour of various mixtures of organic fuels, magnesium and ammonium nitrate (AN) has been examined by differential thermal analysis technique. It has been observed that the thermal decomposition/ignition of organic fuel-AN mixtures is modified significantly in the presence of magnesium metal. The decomposition characteristics of the binary mixtures of AN with various metals indicate the specific action of magnesium and zinc in lowering the decomposition temperature. A possible explanation for the low temperature decomposition is given in terms of the solid state reaction causing the fusion of AN which further reacts with the metal resulting in a highly exothermic reaction.

Chemical Aspects of the Synergistic Hypergolic Ignition in Hybrid Systems with N2O4 as Oxidizer

Synergistic hypergolic ignition with nitrogen tetroxide ( N2O4) as oxidizer has been observed in hybrid systems comprising of a mixture of magnesium and Schiff bases as fuels. The ignition delays (IDs) measured using a modified device, have been compared with those of magnesium-Schiff base-WFNA systems under identical conditions. The ID has been found to vary with the nature of the substitution in both the benzene rings. A linear relationship emerges when the ignition delays are plotted against the Hammett substitution constants (σ). The preignition products of the reaction of N2O4 with magnesium and benzylidineaniline have been analysed to be Mg(NO3)2, benzenediazonium salt and benzaldehyde. Based on the preignition products isolated, a probable reaction mechanism has been proposed. The previously proposed preignition mechanism for the Schiff base-magnesium-WFNA system has been further supported from the present ignition delay data.

Low Temperature Synthesis of Nano-Crystalline CaCu3Ti4O12 Through aFuel Mediated Auto-Combustion Pathway

A novel, cost effective,environment-friendly and energetically beneficial alternative method for the synthesis of giant dielectric pseudo-perovskite material CaCu3Ti4O12 (CCTO) is presented. The method involved auto-combustion of an aqueous precursor solution in oxygen atmosphere with the help of external fuels and is capable of producing high amount of CCTO at ultra-low temperature, in the combustion residue itself. The amount of phase generated was observed to be highly dependent on the combustion process i.e. on the nature and amount of external-fuels added for combustion. Two successful fuel combinations capable of producing reasonably higher amount of the desired compound were investigated. On a structural characterization grain size was observed to decrease drastically to nano-dimension compared to submicron-size that was obtained in a traditional sol-gel combustion and subsequent cacination method. Therefore, the method reported can produce nano-crystalline CaCu3Ti4O12 ceramic matrix at an ultra-low temperature and is expected to be applicable for other multifunctional perovskite oxide materials.

Biomassan energia-arvon nostaminen sekundäärilämmöllä kuivaamalla

Viime aikoina ilmastonmuutos, fossiilisten polttoaineiden väheneminen ja niiden hinnan nousu ovat lisänneet merkittävästi maailmanlaajuista kiinnostusta uusiutuviin energiavaroihin. Suomessa uusiutuvien energialähteiden käytössä on jo pitkään panostettu metsäteollisuuden sivutuotevirtana tuottamaan puuperäiseen biomassaan, jota metsäteollisuus käyttää energiantuotantoonsa. Metsäteollisuuden jätevesien käsittelyssä syntyy erilaisia lietteitä, jotka joko uusiokäytetään tai hävitetään polttamalla tai sijoittamalla kaatopaikalle. Erityisesti biolietteiden uusiokäyttö on hankalaa ja kaatopaikkasijoitus tulevaisuudessa mahdotonta tai ainakin kustannuksiltaan kohtuutonta. Käytännössä liete hävitetään polttamalla ja kuivaamalla siitä tulee polttoaine. Lietteiden energiakäyttö on järkevin tapa hävittää jäteliete. Lietteiden korkean vesipitoisuuden vuoksi ne tulee kuitenkin kuivata ennen polttoa. Lietteen kuivaaminen sekundäärienergiavirralla eli metsäteollisuusprosesseissa sivutuotteena muodostuvalla ns. hukkalämmöllä lisää lietteen poltosta saatavaa energiamäärää ja korvaa fossiilisten polttoaineiden käyttöä. Tutkimuksen tavoitteena oli selvittää lietteen kuivaukseen optimaalisin kuoren ja lietteen seossuhde eri kuivausparametrejä vaihdellen. Kokeellinen työ aloitettiin rakentamalla energiatekniikan koehalliin laboratoriokokoluokan kiintopetikuivuri, jossa kuivumista tutkittiin puhaltamalla polttoainepedin läpi lämmitettyä ilmaa. Kuivattavina polttoaineina olivat kuoren ja lietteen seos tai pelkkä kuori ja liete erilaisilla massoilla ja erilaisilla prosenttisilla suhteilla ja erilaisissa lämpötiloissa. Kuivumiskäyrien määritys perustui massanmuutokseen. Koelaitteessa olivat anturit lämpötilan mittausta varten, jotta lämpötila saatiin säädettyä ja seurattua kokeen edellyttämällä tavalla. Lämpötilat ja painonmuutokset tallentuivat koetta tehdessä tietokoneelle. Kuivauskokeet osoittivat, että liete-kuori seos kuivuu hyvin kiintopedissä kun lietteen massaosuus seoksessa on korkeintaan 50 %. Lietteen massaosuuden ollessa tätä suurempi kuivaaminen ei enää ole tehokasta, mikä johtuu luultavasti ilman suuresta kanavoitumisesta kuivauspedissä. Kuorta kuivatessa lämpötilan nosto 50 °C:stä 70 °C:een oli huomattavasti tehokkaampaa kuin 70 °C:stä 90 °C:een, ajallisesti ero oli noin kaksinkertainen.

The status and use of tree biomass in a semi-arid village ecosystem

The status of the tree biomass resource was investigated in Ungra, a semi-arid village ecosystem in South India. There were 57 tree species with 12 trees capita−1 and 35 trees ha−1. Multiple benefit yielding local tree species dominated the village ecosystem, while fuel only or single end use trees accounted for a small proportion of trees. The standing tree biomass is adequate to meet the requirement of biomass fuels for cooking only for about two years. Village tree biomass is presently being depleted largely for export to urban areas. Tree regeneration is now characterized by transformation from multiple-use local tree species to a few single-use species. A large potential exists for tree biomass production along field boundaries (bunds), stream banks and roadsides. Biomass estimation equations were developed for 10 species.

Rauhan atomi, sodan koodi : Suomalaisen atomivoimaratkaisun teknopolitiikka 1955-1970

This dissertation investigates the atomic power solution in Finland between 1955 - 1970. During these years a national arrangement for atomic energy technology evolved. The foundations of the Finnish atomic energy policy; the creation of basic legislation and the first governmental bodies, were laid between 1955 - 1965. In the late 1960's, the necessary technological and political decisions were made in order to purchase the first commercial nuclear reactor. A historical narration of this process is seen in the international context of "atoms for peace" policies and Cold War history in general. The geopolitical position of Finland made it necessary to become involved in the balanced participation in international scientific-technical exchange and assistive nuclear programs. The Paris Peace Treaty of 1947 categorically denied Finland acquisition of nuclear weapons. Accordingly, from the "Geneva year" of 1955, the emphasis was placed on peaceful purposes for atomic energy as well as on the education of national professionals in Finland. An initiative for the governmental atomic energy commission came from academia but the ultimate motive behind it was an anticipated structural change in the supply of national energy. Economically exploitable hydro power resources were expected to be built within ten years and atomic power was seen as a promising and complementing new energy technology. While importing fuels like coal was out of the question, because of scarce foreign currency, domestic uranium mineral deposits were considered as a potential source of nuclear fuel. Nevertheless, even then nuclear energy was regarded as just one of the possible future energy options. In the mid-1960 s a bandwagon effect of light water reactor orders was witnessed in the United States and soon elsewhere in the world. In Finland, two separate invitations for bids for nuclear reactors were initiated. This study explores at length both their preceding grounds and later phases. An explanation is given that the parallel, independent and nearly identical tenders reflected a post-war ideological rivalry between the state-owned utility Imatran Voima and private energy utilities. A private sector nuclear power association Voimayhdistys Ydin represented energy intensive paper and pulp industries and wanted to have free choice instead of being associated themselves with "the state monopoly" in energy pricing. As a background to this, a decisive change had started to happen within Finnish energy policy: private and municipal big thermal power plants became incorporated into the national hydro power production system. A characteristic phenomenon in the later history is the Soviet Union s effort to bid for the tender of Imatran Voima. A nuclear superpower was willing to take part in competition but not on a turnkey basis as Imatran Voima had presumed. As a result of many political turns and four years of negotiations the first Finnish commercial light water reactor was ordered from the East. Soon after this the private nuclear power group ordered its reactors from Sweden. This work interprets this as a reasonable geopolitical balance in choosing politically sensitive technology. Conceptually, social and political dimensions of new technology are emphasised. Negotiations on the Finnish atomic energy program are viewed as a cooperation and a struggle, where state-oriented and private-oriented regimes pose their own macro level views and goals (technopolitical imaginaries) and defend and advance their plans and practical modes of action (schemata). Here, not only technologists but even political actors are seen to contribute to technopolitical realisations.

Solid State Electrochemical Sensors in Process Control

The basic principles of operation of gas sensors based on solid-state galvanic cells are described. The polarisation of the electrodes can be minimised by the use of point electrodes made of the solid electrolyte, the use of a reference system with chemical potential close to that of the sample system and the use of graded condensed phase reference electrodes. Factors affecting the speed of response of galvanic sensors in equilibrium and non-equilibrium gas mixtures are considered with reference to products of combustion of fossil fuels. An expression for the emf of non-isothermal galvanic sensors and the criterion for the design of temperature compensated reference electrodes for non-isothermal galvanic sensors are briefly outlined. Non-isothermal sensors are useful for the continuous monitoring of concentrations or chemical potentials in reactive systems at high temperatures. Sensors for oxygen, carbon, and alloying elements (Zn and Si) in liquid metals and alloys are discussed. The use of auxiliary electrodes permits the detection of chemical species in the gas phase which are not mobile in the solid electrolyte. Finally, the cause of common errors in galvanic measurements, and tests for correct functioning of galvanic sensors are given. 60 ref.--AA

A Thermodynamic Proposal for the Exposition of Critically and other Subtle Features in Self-Deflagrating Ammonium Perchlorate Systems

A first comprehensive investigation on the deflagration of ammonium perchlorate (AP) in the subcritical regime, below the low pressure deflagration limit (LPL, 2.03 MPa) christened as regime I$^{\prime}$, is discussed by using an elegant thermodynamic approach. In this regime, deflagration was effected by augmenting the initial temperature (T$_{0}$) of the AP strand and by adding fuels like aliphatic dicarboxylic acids or polymers like carboxy terminated polybutadiene (CTPB). From this thermodynamic model, considering the dependence of burning rate ($\dot{r}$) on pressure (P) and T$_{0}$, the true condensed (E$_{\text{s,c}}$) and gas phase (E$_{\text{s,g}}$) activation energies, just below and above the surface respectively, have been obtained and the data clearly distinguishes the deflagration mechanisms in regime I$^{\prime}$ and I (2.03-6.08 MPa). Substantial reduction in the E$_{\text{s,c}}$ of regime I$^{\prime}$, compared to that of regime I, is attributed to HClO$_{4}$ catalysed decomposition of AP. HClO$_{4}$ formation, which occurs only in regime I$^{\prime}$, promotes dent formation on the surface as revealed by the reflectance photomicrographs, in contrast to the smooth surface in regime I. The HClO$_{4}$ vapours, in regime I$^{\prime}$, also catalyse the gas phase reactions and thus bring down the E$_{\text{s,g}}$ too. The excess heat transferred on to the surface from the gas phase is used to melt AP and hence E$_{\text{s,c}}$, in regime I, corresponds to the melt AP decomposition. It is consistent with the similar variation observed for both the melt layer thickness and $\dot{r}$ as a function of P. Thermochemical calculations of the surface heat release support the thermodynamic model and reveal that the AP sublimation reduces the required critical exothermicity of 1108.8 kJ kg$^{-1}$ at the surface. It accounts for the AP not sustaining combustion in the subcritical regime I$^{\prime}$. Further support for the model comes from the temperature-time profiles of the combustion train of AP. The gas and condensed phase enthalpies, derived from the profile, give excellent agreement with those computed thermochemically. The $\sigma _{\text{p}}$ expressions derived from this model establish the mechanistic distinction of regime I$^{\prime}$ and I and thus lend support to the thermodynamic model. On comparing the deflagration of strand against powder AP, the proposed thermodynamic model correctly predicts that the total enthalpy of the condensed and gas phases remains unaltered. However, 16% of AP particles undergo buoyant lifting into the gas phase in the `free board region' (FBR) and this renders the demarcation of the true surface difficult. It is found that T$_{\text{s}}$ lies in the FBR and due to this, in regime I$^{\prime}$, the E$_{\text{s,c}}$ of powder AP matches with the E$_{\text{s,g}}$ of the pellet. The model was extended to AP/dicarboxylic acids and AP/CTPB mixture. The condensed ($\Delta $H$_{1}$) and gas phase ($\Delta $H$_{2}$) enthalpies were obtained from the temperature profile analyses which fit well with those computed thermochemically. The $\Delta $H$_{1}$ of the AP/succinic acid mixture was found just at the threshold of sustaining combustion. Indeed the lower homologue malonic acid, as predicted, does not sustain combustion. In vaporizable fuels like sebacic acid the E$_{\text{s,c}}$ in regime I$^{\prime}$, understandably, conforms to the AP decomposition. However, the E$_{\text{s,c}}$ in AP/CTPB system corresponds to the softening of the polymer which covers AP particles to promote extensive condensed phase reactions. The proposed thermodynamic model also satisfactorily explains certain unique features like intermittent, plateau and flameless combustion in AP/ polymeric fuel systems.

Emerging bioenergy business at Finnish independent industrial sawmills

Finnish forest industry is in the middle of a radical change. Deepening recession and the falling demand of woodworking industry´s traditional products have forced also sawmilling industry to find new and more fertile solutions to improve their operational preconditions. In recent years, the role of bioenergy production has often been highlighted as a part of sawmills´ business repertoire. Sawmilling produces naturally a lot of by-products (e.g. bark, sawdust, chips) which could be exploited more effectively in energy production, and this would bring more incomes or maybe even create new business opportunities for sawmills. Production of bioenergy is also supported by government´s climate and energy policies favouring renewable energy sources, public financial subsidies, and soaring prices of fossil fuels. Also the decreasing production of domestic pulp and paper industry releases a fair amount of sawmills´ by-products for other uses. However, bioenergy production as a part of sawmills´ by-product utilization has been so far researched very little from a managerial point of view. The purpose of this study was to explore the relative significance of the main bioenergy-related processes, resources and factors at Finnish independent industrial sawmills including partnerships, cooperation, customers relationships and investments, and also the future perspectives of bioenergy business at these sawmills with the help of two resource-based approaches (resource-based view, natural-resource-based view). Data of the study comprised of secondary data (e.g. literature), and primary data which was attracted from interviews directed to sawmill managers (or equivalent persons in charge of decisions regarding bioenergy production at sawmill). While a literature review and the Delphi method with two questionnaires were utilized as the methods of the study. According to the results of the study, the most significant processes related to the value chain of bioenergy business are connected to raw material availability and procurement, and customer relationships management. In addition to raw material and services, the most significant resources included factory and machinery, personnel, collaboration, and geographic location. Long-term cooperation deals were clearly valued as the most significant form of collaboration, and especially in processes connected to raw material procurement. Study results also revealed that factors related to demand, subsidies and prices had highest importance in connection with sawmills´ future bioenergy business. However, majority of the respondents required that certain preconditions connected to the above-mentioned factors should be fulfilled before they will continue their bioenergy-related investments. Generally, the answers showed a wide divergence of opinions among the respondents which may refer to sawmills´ different emphases and expectations concerning bioenergy. In other words, bioenergy is still perceived as a quite novel and risky area of business at Finnish independent industrial sawmills. These results indicate that the massive expansion of bioenergy business at private sawmills in Finland is not a self-evident truth. The blocking barriers seem to be connected mainly to demand of bioenergy and money. Respondents´ answers disseminated a growing dissatisfaction towards the policies of authorities, which don´t treat equally sawmill-based bioenergy compared to other forms of bioenergy. This proposition was boiled down in a sawmill manager´s comment: “There is a lot of bioenergy available, if they just want to make use of it.” It seems that the positive effects of government´s policies favouring the renewables are not taking effect at private sawmills. However, as there anyway seems to be a lot of potential connected to emerging bioenergy business at Finnish independent industrial sawmills, there is also a clear need for more profound future studies over this topic.

Renewable Energy and Climate Policies: Studies in the Forest and Energy Sector

‪This dissertation examines the impacts of energy and climate policies on the energy and forest sectors, focusing on the case of Finland. The thesis consists of an introduction article and four separate studies. The dissertation was motivated by the climate concern and the increasing demand of renewable energy. In particular, the renewable energy consumption and greenhouse gas emission reduction targets of the European Union were driving this work. In Finland, both forest and energy sectors are in key roles in achieving these targets. In fact, the separation between forest and energy sector is diminishing as the energy sector is utilizing increasing amounts of wood in energy production and as the forest sector is becoming more and more important energy producer.‬ ‪The objective of this dissertation is to find out and measure the impacts of climate and energy policies on the forest and energy sectors. In climate policy, the focus is on emissions trading, and in energy policy the dissertation focuses on the promotion of renewable forest-based energy use. The dissertation relies on empirical numerical models that are based on microeconomic theory. Numerical partial equilibrium mixed complementarity problem models were constructed to study the markets under scrutiny. The separate studies focus on co-firing of wood biomass and fossil fuels, liquid biofuel production in the pulp and paper industry, and the impacts of climate policy on the pulp and paper sector.‬ ‪The dissertation shows that the policies promoting wood-based energy may have have unexpected negative impacts. When feed-in tariff is imposed together with emissions trading, in some plants the production of renewable electricity might decrease as the emissions price increases. The dissertation also shows that in liquid biofuel production, investment subsidy may cause high direct policy costs and other negative impacts when compared to other policy instruments. The results of the dissertation also indicate that from the climate mitigation perspective, perfect competition is the favored wood market competition structure, at least if the emissions trading system is not global.‬ ‪In conclusion, this dissertation suggests that when promoting the use of wood biomass in energy production, the favored policy instruments are subsidies that promote directly the renewable energy production (i.e. production subsidy, renewables subsidy or feed-in premium). Also, the policy instrument should be designed to be dependent on the emissions price or on the substitute price. In addition, this dissertation shows that when planning policies to promote wood-based renewable energy, the goals of the policy scheme should be clear before decisions are made on the choice of the policy instruments.‬

Studies on a stove for powdery biomass

The sawdust stove, classically known for several decades, is considered here in a scientific study. The poor ignition characteristics and smoky start up are related to improper geometric dimensions. Based on a parametric study, the startup procedure and the dimensions of the stove were modified to achieve a smooth start up. Also, the range of acceptable fuels was enlarged to include tiny unprocessed dry twigs, weeds and wood sticks o the extent of about 50%, with the rest being sawdust-like material. The efficiency of the stove was measured to be 30–40%, depending on the relative size and shape of the vessel and the power level of the stove. A simple procedure for designing this class of stove for various power levels, as well as burning times, is presented. A new concept of multiport design is also discussed.

Combustion synthesis of yttria

Fine-particle, sinter-active yttria has been prepared by combustion of a redox compound, Y(N2H3COO)3·3H2O and mixtures of Y(N2H3COO)3·3H2O�NH4NO3 or NH4ClO4 as well as yttrium nitrate and hydrazine-based fuels. The fineparticle nature of the combustion-derived yttria has been investigated using powder density, particle size and BET surface area measurements. The uniaxially, cold-pressed fine-particle yttria when sintered at 1450�1500 °C achieved 98% theoretical density and showed a fine-grain (1�2 µm) microstructure.

Spontaneously Igniting Hybrid Fuel-Oxidizer Systems

After briefly outlining the recent developments in hybrid rockets, the work carried out by the author on self-igniting (hypergolic) solid fuel-liquid oxidiser systems has been reviewed. A major aspect relates to the solid derivatives of hydrazines, which have been conceived as fuels for hybrid rockets. Many of these N-N bonded compounds ignite readily, with very short ignition delays, on coming into contact with liquid oxidisers, like HNO3 and N2O4. The ignition characteristics have been examined as a function of the nature of the functional group in the fuel molecule, in an attempt to establish a basis for the hypergolic ignition in terms of chemical reactivity of the fuel-oxidiser combination. Important chemical reactions occurring in the pre-ignition stage have been identified by examining the quenched reaction products. Hybrid systems exhibiting synergistic hypergolicity in the presence of metal powders have been investigated. An estimation of the rocket performance parameters, experimental determination of the heats of combustion in HNO3, thermal decomposition characteristics, temperature profile by thin film thermometry and and product identification by the rapid scan FT-IR, are among the other relevant studies made on these systems. A significant recent development has been the synthesis of new N-N bonded viscous binders, capable of retaining the hypergolicity of the fuel powders embedded therein as well as providing the required mechanical strength to the grain. Several of these resins have been characterised. Metallised fuel composites of these resins having high loading of magnesium are found to have short ignition delays and high performance parameters.