Entwicklung einer Fokalebenen-Driftkammer für niederenergetische Pionen und experimentelle Bestimmung einer inversen Transfermatrix für das Short-Orbit-Spektrometer

Die Drei-Spektrometer-Anlage am Mainzer Institut für Kernphysik wurde um ein zusätzliches Spektrometer ergänzt, welches sich durch seine kurze Baulänge auszeichnet und deshalb Short-Orbit-Spektrometer (SOS) genannt wird. Beim nominellen Abstand des SOS vom Target (66 cm) legen die nachzuweisenden Teilchen zwischen Reaktionsort und Detektor eine mittlere Bahnlänge von 165 cm zurück. Für die schwellennahe Pionproduktion erhöht sich dadurch im Vergleich zu den großen Spektrometern die Überlebenswahrscheinlichkeit geladener Pionen mit Impuls 100 MeV/c von 15% auf 73%. Demzufolge verringert sich der systematische Fehler ("Myon-Kontamination"), etwa bei der geplanten Messung der schwachen Formfaktoren G_A(Q²) und G_P(Q²), signifikant. Den Schwerpunkt der vorliegenden Arbeit bildet die Driftkammer des SOS. Ihre niedrige Massenbelegung (0,03% X_0) zur Reduzierung der Kleinwinkelstreuung ist auf den Nachweis niederenergetischer Pionen hin optimiert. Aufgrund der neuartigen Geometrie des Detektors musste eine eigene Software zur Spurrekonstruktion, Effizienzbestimmung etc. entwickelt werden. Eine komfortable Möglichkeit zur Eichung der Driftweg-Driftzeit-Relation, die durch kubische Splines dargestellt wird, wurde implementiert. Das Auflösungsvermögen des Spurdetektors liegt in der dispersiven Ebene bei 76 µm für die Orts- und 0,23° für die Winkelkoordinate (wahrscheinlichster Fehler) sowie entsprechend in der nicht-dispersiven Ebene bei 110 µm bzw. 0,29°. Zur Rückrechnung der Detektorkoordinaten auf den Reaktionsort wurde die inverse Transfermatrix des Spektrometers bestimmt. Hierzu wurden an Protonen im ¹²C-Kern quasielastisch gestreute Elektronen verwendet, deren Startwinkel durch einen Lochkollimator definiert wurden. Daraus ergeben sich experimentelle Werte für die mittlere Winkelauflösung am Target von sigma_phi = 1,3 mrad bzw. sigma_theta = 10,6 mrad. Da die Impulseichung des SOS nur mittels quasielastischer Streuung (Zweiarmexperiment) durchgeführt werden kann, muss man den Beitrag des Protonarms zur Breite des Piks der fehlenden Masse in einer Monte-Carlo-Simulation abschätzen und herausfalten. Zunächst lässt sich nur abschätzen, dass die Impulsauflösung sicher besser als 1% ist.

Strukturfaktoren, Modenkopplungsgleichungen und Glasübergang molekularer Kristalle

In dieser Arbeit wird der Orientierungsglasübergang ungeordneter, molekularer Kristalle untersucht. Die theoretische Behandlung ist durch die Anisotropie der Einteilchen-Verteilungsfunktion und der Paarfunktionen erschwert. Nimmt man ein starres Gitter, wird der reziproke Raum im Gegenzug auf die 1. Brillouin-Zone eingeschränkt. Der Orientierungsglasübergang wird im Rahmen der Modenkopplungsgleichungen studiert, die dazu hergeleitet werden. Als Modell dienen harte Rotationsellipsoide auf einem starren sc Gitter. Zur Berechnung der statischen tensoriellen Strukturfaktoren wird die Ornstein-Zernike(OZ)-Gleichung molekularer Kristalle abgeleitet und selbstkonsistent zusammen mit der von molekularen Flüssigkeiten übernommenen Percus-Yevick(PY)-Näherung gelöst. Parallel dazu werden die Strukturfaktoren durch MC-Simulationen ermittelt. Die OZ-Gleichung molekularer Kristalle ähnelt der von Flüssigkeiten, direkte und totale Korrelationsfunktion kommen jedoch wegen des starren Gitters nur ohne Konstantanteile in den Winkelvariablen vor, im Gegensatz zur PY-Näherung. Die Anisotropie bringt außerdem einen nichttrivialen Zusatzfaktor. OZ/PY-Strukturfaktoren und MC-Ergebnisse stimmen gut überein. Bei den Matrixelementen der Dichte-Dichte-Korrelationsfunktion gibt es drei Hauptverläufe: oszillatorisch, monoton und unregelmäßig abfallend. Oszillationen gehören zu alternierenden Dichtefluktuationen, führen zu Maxima der Strukturfaktoren am Zonenrand und kommen bei oblaten und genügend breiten prolaten, schwächer auch bei dünnen, nicht zu langen prolaten Ellipsoiden vor. Der exponentielle monotone Abfall kommt bei allen Ellipsoiden vor und führt zu Maxima der Strukturfaktoren in der Zonenmitte, was die Tendenz zu nematischer Ordnung zeigt. Die OZ/PY-Theorie ist durch divergierende Maxima der Strukturfaktoren begrenzt. Bei den Modenkopplungsgleichungen molekularer Kristalle zeigt sich eine große Ähnlichkeit mit denen molekularer Flüssigkeiten, jedoch spielen auf einem starrem Gitter nur die Matrixelemente mit l,l' > 0 eine Rolle und es finden Umklapps von reziproken Vektoren statt. Die Anisotropie bringt auch hier nichtkonstante Zusatzfaktoren ins Spiel. Bis auf flache oblate Ellipsoide wird die Modenkopplungs-Glaslinie von der Divergenz der Strukturfaktoren bestimmt. Für sehr lange Ellipsoide müssen die Strukturfaktoren zur Divergenz hin extrapoliert werden. Daher treibt nicht der Orientierungskäfigeffekt den Glasübergang, sondern Fluktuationen an einer Phasengrenze. Nahe der Kugelform ist keine zuverlässige Glasline festlegbar. Die eingefrorenen kritischen Dichte-Dichte-Korrelatoren haben nur in wenigen Fällen die Oszillationen der statischen Korrelatoren. Der monotone Abfall bleibt dagegen für lange Zeiten meist erhalten. Folglich haben die kritischen Modenkopplungs-Nichtergodizitätsparameter abgeschwächte Maxima in der Zonenmitte, während die Maxima am Zonenrand meist verschwunden sind. Die normierten Nichtergodizitätsparameter zeigen eine Fülle von Verläufen, besonders tiefer im Glas.

Supramolecular approaches to organized luminescent nanostructures for sensing, labeling and imaging applications

The common thread of this thesis is the will of investigating properties and behavior of assemblies. Groups of objects display peculiar properties, which can be very far from the simple sum of respective components’ properties. This is truer, the smaller is inter-objects distance, i.e. the higher is their density, and the smaller is the container size. “Confinement” is in fact a key concept in many topics explored and here reported. It can be conceived as a spatial limitation, that yet gives origin to unexpected processes and phenomena based on inter-objects communication. Such phenomena eventually result in “non-linear properties”, responsible for the low predictability of large assemblies. Chapter 1 provides two insights on surface chemistry, namely (i) on a supramolecular assembly based on orthogonal forces, and (ii) on selective and sensitive fluorescent sensing in thin polymeric film. In chapters 2 to 4 confinement of molecules plays a major role. Most of the work focuses on FRET within core-shell nanoparticles, investigated both through a simulation model and through experiments. Exciting results of great applicative interest are drawn, such as a method of tuning emission wavelength at constant excitation, and a way of overcoming self-quenching processes by setting up a competitive deactivation channel. We envisage applications of these materials as labels for multiplexing analysis, and in all fields of fluorescence imaging, where brightness coupled with biocompatibility and water solubility is required. Adducts of nanoparticles and molecular photoswitches are investigated in the context of superresolution techniques for fluorescence microscopy. In chapter 5 a method is proposed to prepare a library of functionalized Pluronic F127, which gives access to a twofold “smart” nanomaterial, namely both (i)luminescent and (ii)surface-functionalized SCSSNPs. Focus shifts in chapter 6 to confinement effects in an upper size scale. Moving from nanometers to micrometers, we investigate the interplay between microparticles flowing in microchannels where a constriction affects at very long ranges structure and dynamics of the colloidal paste.

Visualization, manipulation and force spectroscopy of cylindrical polymer brushes

The Ph.D. thesis deals with the conformational study of individual cylindrical polymer brush molecules using atomic force microscopy (AFM). Imaging combined with single molecule manipulation has been used to unravel questions concerning conformational changes, desorption behavior and mechanical properties of individual macromolecules and supramolecular structures. In the first part of the thesis (chapter 5) molecular conformations of cylindrical polymer brushes with poly-(N-isopropylacrylamide) (PNIPAM) side chains were studied in various environmental conditions. Also micelle formation of cylindrical brush-coil blockcopolymers with polyacrylic acid side chains and polystyrene coil have been visualized. In chapter 6 the mechanical properties of single cylindrical polymer brushes with (PNIPAM) side chains were investigated. Assuming that the brushes adopt equilibrium conformation on the surface, an average persistence length of lp= (29 ± 3) nm was determined by the end-to-end distance vs. contour length analysis in terms of the wormlike chain (WLC) model. Stretching experiments suggest that an exact determination of the persistence length using force extension curves is impeded by the contribution of the side chains. Modeling the stretching of the bottle brush molecule as extension of a dual spring (side chain and main chain) explains the frequently observed very low persistence length arising from a dominant contribution of the side chain elasticity at small overall contour lengths. It has been shown that it is possible to estimate the “true” persistence length of the bottle brush molecule from the intercept of a linear extrapolation of the inverse square root of the apparent persistence length vs. the inverse contour length plot. By virtue of this procedure a “true” persistence length of 140 nm for the PNIPAM brush molecules is predicted. Chapter 7 and 8 deal with the force-extension behavior of PNIPAM cylindrical brushes studied in poor solvent conditions. The behavior is shown to be qualitatively different from that in a good solvent. Force induced globule-cylinder conformational changes are monitored using “molecule specific force spectroscopy” which is a combined AFM imaging and SMFS technique. An interesting behavior of the unfolding-folding transitions of single collapsed PNIPAM brush molecules has been observed by force spectroscopy using the so called “fly-fishing” mode. A plateau force is observed upon unfolding the collapsed molecule, which is attributed to a phase transition from a collapsed brush to a stretched conformation. Chapter 9 describes the desorption behavior of single cylindrical polyelectrolyte brushes with poly-L-lysine side chains deposited on a mica surface using the “molecule specific force spectroscopy” technique to resolve statistical discrepancies usually observed in SMFS experiments. Imaging of the brushes and inferring the persistence length from a end-to-end distance vs. contour length analysis results in an average persistence length of lp = (25 ± 5) nm assuming that the chains adopt their equilibrium conformation on the surface. Stretching experiments carried out on individual poly-L-lysine brush molecules by force spectroscopy using the “fly-fishing” mode provide a persistence length in the range of 7-23 nm in reasonable accordance with the imaging results. In chapter 10 the conformational behavior of cylindrical poly-L-lysine brush-sodium dodecyl sulfate complexes was studied using AFM imaging. Surfactant induced cylinder to helix like to globule conformational transitions were observed.

Theoretical and numerical study of the laser-plasma ion acceleration

The laser driven ion acceleration is a burgeoning field of resarch and is attracting a growing number of scientists since the first results reported in 2000 obtained irradiating thin solid foils by high power laser pulses. The growing interest is driven by the peculiar characteristics of the produced bunches, the compactness of the whole accelerating system and the very short accelerating length of this all-optical accelerators. A fervent theoretical and experimental work has been done since then. An important part of the theoretical study is done by means of numerical simulations and the most widely used technique exploits PIC codes (“Particle In Cell'”). In this thesis the PIC code AlaDyn, developed by our research group considering innovative algorithms, is described. My work has been devoted to the developement of the code and the investigation of the laser driven ion acceleration for different target configurations. Two target configurations for the proton acceleration are presented together with the results of the 2D and 3D numerical investigation. One target configuration consists of a solid foil with a low density layer attached on the irradiated side. The nearly critical plasma of the foam layer allows a very high energy absorption by the target and an increase of the proton energy up to a factor 3, when compared to the ``pure'' TNSA configuration. The differences of the regime with respect to the standard TNSA are described The case of nearly critical density targets has been investigated with 3D simulations. In this case the laser travels throughout the plasma and exits on the rear side. During the propagation, the laser drills a channel and induce a magnetic vortex that expanding on the rear side of the targer is source of a very intense electric field. The protons of the plasma are strongly accelerated up to energies of 100 MeV using a 200PW laser.

Discotic materials for organic electronics

Die Kontrolle der ausgeprägten Aggregationsfähigkeit von alkylsubstituierten Hexa-peri-hexabenzocoronenen (HBC) wurde durch die Reduktion der intermolekularen Wechselwirkungen erreicht. Sterisch anspruchsvolle, verzweigte Alkylketten, mit einem Verzweigungspunkt naher des aromatischen Kerns, wurden in die Corona der aromatischen Scheiben eingebracht und verleihen den Derivaten Schmelzbarkeit ohne thermische Zersetzung. Dies erlaubte eine kostengünstige Verarbeitungstechniken direkt aus der Schmelze wie z.B. Zonenschmelzen, um uniaxial organisierte makroskopische Filme zu erhalten. Abhängig von dem sterischen Anspruch, der durch die Seitenkette erzeugt wird, wurden unterschiedliche molekulare Orientierungen auf Oberflächen erhalten, was eine wichtige Voraussetzung ist, um diskotische Materialien in elektronische Bauteile zu implementieren. Eine weitere Voraussetzung sind hohe Ladungsträgerbeweglichkeiten und Ladungsträgerlebenszeiten in den Halbleitermaterialien, die mit time-resolved pulse-radiolysis microwave conductivity (TR-PRMC) und time-of-flight (TOF) auch für die synthetisieren Materialien bestimmt wurden. Die neuen Materialien zeigten bereits in organischen Solarzellen gute Leistungen. Den Einfluss des Perimeters auf die elektronischen Eigenschaften der polyzyklischen aromatischen Kohlenwasserstoffe (PAKs) wurde theoretisch vorhergesagt und in dieser Arbeit durch die Synthese einer homologe Serie von PAKs experimentell bestätigt. Geht man von der „arm-chair“ Peripherie des HBC sukzessive zu einer partiellen „zickzack“ Peripherie, so findet man eine Abhängigkeit der elektronischen Banden von Symmetrie und Größe des aromatischen Systems. Die spontan ausgebildete Überstruktur dieser Derivate zeigte eine Abhängigkeit von Substitutionsmuster und der Natur der Alkylketten. Zusammenfassend wurden neben der Synthese von neuartigen Materialien für den Einsatz in der organischen Elektronik Synthesen entwickelt, die eine vereinfachte Funktionalisierung von ausgedehnten PAKs ermöglicht. Diese Konzepte erlauben eine Justierung der molekularen und supramolekularen Eigenschaften, eines der wichtigsten Voraussetzungen für den Einsatz von Materialien in elektronischen Bauelementen.

Aktivierung von Hämocyanin zur Tyrosinase

Ziel der Arbeit war die enzymatische Aktivierung von Cheliceraten-Hämocyanin zur Erforschung ihrer Phenoloxidase-Aktivität. Hierzu wurden zwei Hämocyanine in vergleichenden Untersuchungen herangezogen: Das bekannte 24-mer aus der Spinne Eurypelma californicum und das ebenfalls 24-mere Hämocyanin des Skorpions Pandinus imperator, dessen Struktur hier aufgeklärt wurde. Elektronenmikroskopisch und in der dynamischer Lichtstreuung sind sich beide Hämocyanine sehr ähnlich und sedimentieren bei analytischer Ultrazentrifugation ebenfalls in gleicher Weise (Sedimentationskoeffizient von 37 S (S20, W)). Durch Dissoziation im alkalischen Milieu gewinnt man bis zu zwölf Untereinheiten, von denen sich neun immunologisch unterscheiden lassen. Das absorptionsspektroskopische Verhalten von P. imperator- und E. californicum-Hämocyanin sowie Sekundärstrukturanalyse mittels CD-Spektroskopie ist nahezu identisch. Die Stabilität des Hämocyanins gegenüber Temperatur und Denaturierungsmitteln wurde mit Circulardichroismus- und Fluoreszenzspektroskopie sowie durch die enzymatische Aktivität untersucht. Erstmals konnten die Hämocyanine von P. imperator und E. californicum nicht nur zu einer stabilen Diphenoloxidase umgewandelt werden, sondern auch eine Monophenolhydroxylase-Aktivität induziert und reguliert werden. Für letztere Aktivität ist dabei die Präsenz von Tris- oder Hepes-Puffer wesentlich. Während sich die Monophenolhydroxylase-Aktivität nur auf Ebene der oligomeren Zustände beobachten lässt, erkennt man bei den isolierten Untereinheiten-Typen lediglich eine Diphenoloxidase-Aktivität. Bei dem Spinnen-Hämocyanin zeigen die Untereinheiten bc die stärkste katalytische Aktivität auf, bei P. imperator-Hämocyanin findet man drei bis vier Untereinheiten, die enzymatisch aktiv sind. Die Aktivierung mit SDS liefert den Hinweis, dass die Quartärstruktur in eine andere Konformation gebracht und nicht durch SDS denaturiert wird. Zugabe von Mg2+ reguliert die Phenoloxidase-Aktivität und verschiebt bei P. imperator-Hämocyanin die enzymatische Aktivität zugunsten der Diphenoloxidase. Mit keiner der zur Verfügung stehenden Methoden konnte jedoch ein Konformationsübergang eindeutig nachgewiesen werden. Die Stabilität scheint durch die niedrigen SDS-Konzentrationen nicht beeinträchtigt zu werden. Die sehr lange “Verzögerungsphase“ bei der Monophenolhydroxylase-Aktivität konnte durch Zugabe von katalytischem Diphenol drastisch verkürzt werden, was ein Hinweis auf die echte Tyrosinase-Aktivität des aktivierten Hämocyanins ist. Ein in vivo-Aktivator konnte bis jetzt noch nicht gefunden werden. Trotzdem scheinen die Hämocyanine in der Immunologie von Cheliceraten eine bedeutende Rolle zu spielen, indem sie die Rolle der Tyrosinasen / Phenoloxidasen beziehungsweise Catecholoxidasen übernehmen, die bei Cheliceraten nicht vorkommen. Weitere Möglichkeiten des Cheliceraten-Immunsystems, eindringende Fremdorganismen abzuwehren, wurden untersucht. Das Fehlen einer ´echten` Phenoloxidase-Aktivität bei den Cheliceraten, mit der Fähigkeit, sowohl mono- als auch diphenolische Substrate umzusetzen, stützt die Hypothese, dass aktiviertes Hämocyanin in vivo an die Stelle der Phenoloxidase tritt.

Crystal phases and glassy dynamics in monodisperse hard ellipsoids

We have performed Monte Carlo and molecular dynamics simulations of suspensions of monodisperse, hard ellipsoids of revolution. Hard-particle models play a key role in statistical mechanics. They are conceptually and computationally simple, and they offer insight into systems in which particle shape is important, including atomic, molecular, colloidal, and granular systems. In the high density phase diagram of prolate hard ellipsoids we have found a new crystal, which is more stable than the stretched FCC structure proposed previously . The new phase, SM2, has a simple monoclinic unit cell containing a basis of two ellipsoids with unequal orientations. The angle of inclination is very soft for length-to-width (aspect) ratio l/w=3, while the other angles are not. A symmetric state of the unit cell exists, related to the densest-known packings of ellipsoids; it is not always the stable one. Our results remove the stretched FCC structure for aspect ratio l/w=3 from the phase diagram of hard, uni-axial ellipsoids. We provide evidence that this holds between aspect ratios 3 and 6, and possibly beyond. Finally, ellipsoids in SM2 at l/w=1.55 exhibit end-over-end flipping, warranting studies of the cross-over to where this dynamics is not possible. Secondly, we studied the dynamics of nearly spherical ellipsoids. In equilibrium, they show a first-order transition from an isotropic phase to a rotator phase, where positions are crystalline but orientations are free. When over-compressing the isotropic phase into the rotator regime, we observed super-Arrhenius slowing down of diffusion and relaxation, and signatures of the cage effect. These features of glassy dynamics are sufficiently strong that asymptotic scaling laws of the Mode-Coupling Theory of the glass transition (MCT) could be tested, and were found to apply. We found strong coupling of positional and orientational degrees of freedom, leading to a common value for the MCT glass-transition volume fraction. Flipping modes were not slowed down significantly. We demonstrated that the results are independent of simulation method, as predicted by MCT. Further, we determined that even intra-cage motion is cooperative. We confirmed the presence of dynamical heterogeneities associated with the cage effect. The transit between cages was seen to occur on short time scales, compared to the time spent in cages; but the transit was shown not to involve displacements distinguishable in character from intra-cage motion. The presence of glassy dynamics was predicted by molecular MCT (MMCT). However, as MMCT disregards crystallization, a test by simulation was required. Glassy dynamics is unusual in monodisperse systems. Crystallization typically intervenes unless polydispersity, network-forming bonds or other asymmetries are introduced. We argue that particle anisometry acts as a sufficient source of disorder to prevent crystallization. This sheds new light on the question of which ingredients are required for glass formation.

New functionalized ligands for luminescent metal complexes: from design to applications

The synthesis of luminescent metal complexes is a very challenging task since they can be regarded as the starting point for a lot of different areas. Luminescent complexes, in fact, can be used for technological, industrial, medical and biological applications. During my PhD I worked with different metals having distinguishing intrinsic properties that make them different from each other and, in particular, more or less suitable for the different possible uses. Iridium complexes show the best photophysical properties: they have high quantum yields, very long lifetimes and possess easily tunable emissions throughout the visible range. On the other hand, Iridium is very expensive and scarcely available. The aim of my work concerning this metal was, therefore, to synthesize ligands able not only to form luminescent complexes, but also able to add functionalities to the final complex, increasing its properties, and therefore its possible practical uses. Since Re(I) derivatives have been reported to be suitable as probes in biological system, and the use of Re(I) reduces the costs, the synthesized bifunctional ligands containing a pyridine-triazole and a biotin unit were employed to obtain new Re(I) luminescent probes. Part of my work involved the design and synthesis of new ligands able to form stable complexes with Eu(III) and Ce(III) salts, in order to obtain an emission in the range of visible light: these two metals are quite cheap and relatively non-toxic compared to other heavy metals. Finally, I plan to synthesize organic derivatives that already possessed an emission thanks to the presence of other many chromophoric groups and can be able to link the Zinc (II), a low cost and especially non-toxic “green” metal. Zinc has not its own emission, but when it sticks to ligands, it increases their photophysical properties.

Phasenverhalten, Kristallisation und Morphologie ladungsstabilisierter kolloidaler Mischungen

Die vorliegende Arbeit möchte die Anwendbarkeit ladungsstabilisierter kolloidaler Systeme als Modellsysteme für fundamentale Fragen der Festkörperphysik und Thermodynamik auf binäre Mischungen erweitern. In diesem Kontext untersucht sie das Phasenverhalten und mit ihm im Zusammenhang stehende Eigenschaften von binären Mischungen ladungsstabilisierter, sphärischer kolloidaler Partikel in wässriger Suspension. Da das Verhalten hartkugelähnlicher Systeme durch hohe Fremdionenkonzentrationen bereits gut bekannt ist, konzentriert sich diese Arbeit auf sehr langreichweitig repulsive Systeme unter deionisierten Bedingungen. Neben etablierten Methoden der Mikroskopie und statischer Lichtstreuung zur Phasendiagrammsbestimmung wird auch die Beobachtung der zeitabhängigen Entwicklung des Schermoduls verwendet, um eine langsame Erstarrungskinetik zu studieren. Es werden insbesondere Mischungen aus Komponenten unterschiedlicher Größe und Ladung der Größenverhältnisse 0,9, 0,82, 0,57, 0,39 und 0,37 untersucht. Diese zeigen in dieser Reihenfolge Phasendiagramme mit spindelförmigem fluid/kristallinen Koexistenzbereich wie auch azeotrope und eutektische Phasendiagramme. Die Strukturuntersuchungen aus der statischen Lichtstreuung stehen in praktisch allen Fällen im Einklang mit ungeordneten bcc- Substitutionskristallen, was über Modelle zu Schermodulmessungen bestätigt wird. Für das spindelförmige System wird ein überraschend weiter Koexistenzbereich beobachtet, wie er nicht von der Theorie erwartet wird. Die Lage, aber nicht die Form des Solidus stimmt quantitativ mit Simulationsvorhersagen zu einkomponentigen Systemen überein. Für das eutektische System bei einem Radienverhältnis von 0,57 wird der Einfluss der Schwerkraft auf das Phasenverhalten und die Erstarrungskinetik untersucht. Die der Kristallisation der kleineren Majoritätskomponente vorgelagerte gravitativ unterstützte Entmischung begünstigt hier die Verfestigung. Beobachtet werden Morphologien, die aus anderen Systemen bekannt sind (Facetten, Dendriten), wie auch erstmals eine kollumnare eutektische Morphologie. Aus den Ergebnissen wird der erste umfassende Überblick über das Phasenverhalten deionisierter Mischungen ladungsstabilisierter, sphärischer Partikel erstellt, die eine Diskussion der Daten anderer Autoren und unserer Gruppe über fluid-fluider Phasenseparation und einem System mit oberem azeotropen Punkt mit einschließt. Die meisten metallspezifischen Phasendiagrammtypen können mit ladungsstabilisierten kolloidalen Partikeln reproduziert werden. Die langreichweitig wechselwirkenden Partikel zeigt eine wesentlich verbesserte substitutionelle Mischbarkeit im Vergleich mit Hartkugel- und Metallsystemen. Das Größenverhältnis der sphärischen Partikel nimmt dabei die bestimmende Rolle für den Phasendiagrammtyp ein.

Erasure error correcting codes applied to DTN communications.

The space environment has always been one of the most challenging for communications, both at physical and network layer. Concerning the latter, the most common challenges are the lack of continuous network connectivity, very long delays and relatively frequent losses. Because of these problems, the normal TCP/IP suite protocols are hardly applicable. Moreover, in space scenarios reliability is fundamental. In fact, it is usually not tolerable to lose important information or to receive it with a very large delay because of a challenging transmission channel. In terrestrial protocols, such as TCP, reliability is obtained by means of an ARQ (Automatic Retransmission reQuest) method, which, however, has not good performance when there are long delays on the transmission channel. At physical layer, Forward Error Correction Codes (FECs), based on the insertion of redundant information, are an alternative way to assure reliability. On binary channels, when single bits are flipped because of channel noise, redundancy bits can be exploited to recover the original information. In the presence of binary erasure channels, where bits are not flipped but lost, redundancy can still be used to recover the original information. FECs codes, designed for this purpose, are usually called Erasure Codes (ECs). It is worth noting that ECs, primarily studied for binary channels, can also be used at upper layers, i.e. applied on packets instead of bits, offering a very interesting alternative to the usual ARQ methods, especially in the presence of long delays. A protocol created to add reliability to DTN networks is the Licklider Transmission Protocol (LTP), created to obtain better performance on long delay links. The aim of this thesis is the application of ECs to LTP.

Inversion of low frequency seismo-volcanic events

The inversion of seismo-volcanic events is performed to retrieve the source geometry and to determine volumetric budgets of the source. Such observations have shown to be an important tool for the seismological monitoring of volcanoes. We developed a novel technique for the non-linear constrained inversion of low frequency seismo-volcanic events. Unconstrained linear inversion methods work well when a dense network of broadband seismometers is available. We propose a new constrained inversion technique, which has shown to be efficient also in a reduced network configuration and a low signal-noise ratio. The waveform inversion is performed in the frequency domain, constraining the source mechanism during the event to vary only in its magnitude. The eigenvectors orientation and the eigenvalue ratio are kept constant. This significantly reduces the number of parameters to invert, making the procedure more stable. The method has been tested over a synthetic dataset, reproducing realistic very-long-period (VLP) signals of Stromboli volcano. The information obtained by performing the synthetic tests is used to assess the reliability of the results obtained on a VLP dataset recorded on Stromboli volcano and on a low frequency events recorded at Vesuvius volcano.

Methods and strategies to identify the mode of action of phytoactive compounds

Small molecules affecting biological processes in plants are widely used in agricultural practice as herbicides or plant growth regulators and in basic plant sciences as probes to study the physiology of plants. Most of the compounds were identified in large screens by the agrochemical industry, as phytoactive natural products and more recently, novel phytoactive compounds originated from academic research by chemical screens performed to induce specific phenotypes of interest. The aim of the present PhD thesis is to evaluate different approaches used for the identification of the primary mode of action (MoA) of a phytoactive compound. Based on the methodologies used for MoA identification, three approaches are discerned: a phenotyping approach, an approach based on a genetic screen and a biochemical screening approach.rnFour scientific publications resulting from my work are presented as examples of how a phenotyping approach can successfully be applied to describe the plant MoA of different compounds in detail.rnI. A subgroup of cyanoacrylates has been discovered as plant growth inhibitors. A set of bioassays indicated a specific effect on cell division. Cytological investigations of the cell division process in plant cell cultures, studies of microtubule assembly with green fluorescent protein marker lines in vivo and cross resistant studies with Eleusine indica plants harbouring a mutation in alpha-tubulin, led to the description of alpha-tubulin as a target site of cyanoacrylates (Tresch et al., 2005).rnII. The MoA of the herbicide flamprop-m-methyl was not known so far. The studies described in Tresch et al. (2008) indicate a primary effect on cell division. Detailed studies unravelled a specific effect on mitotic microtubule figures, causing a block in cell division. In contrast to other inhibitors of microtubule rearrangement such as dinitroanilines, flamprop-m-methyl did not influence microtubule assembly in vitro. An influence of flamprop-m-methyl on a target within the cytoskeleton signalling network could be proposed (Tresch et al., 2008).rnIII. The herbicide endothall is a protein phosphatase inhibitor structurally related to the natural product cantharidin. Bioassay studies indicated a dominant effect on dark-growing cells that was unrelated to effects observed in the light. Cytological characterisation of the microtubule cytoskeleton in corn tissue and heterotrophic tobacco cells showed a specific effect of endothall on mitotic spindle formation and ultrastructure of the nucleus in combination with a decrease of the proliferation index. The observed effects are similar to those of other protein phosphatase inhibitors such as cantharidin and the structurally different okadaic acid. Additionally, the observed effects show similarities to knock-out lines of the TON1 pathway, a protein phosphatase-regulated signalling pathway. The data presented in Tresch et al. (2011) associate endothall’s known in vitro inhibition of protein phosphatases with in vivo-effects and suggest an interaction between endothall and the TON1 pathway.rnIV. Mefluidide as a plant growth regulator induces growth retardation and a specific phenotype indicating an inhibition of fatty acid biosynthesis. A test of the cuticle functionality suggested a defect in the biosynthesis of very-long-chain fatty acids (VLCFA) or waxes. Metabolic profiling studies showed similarities with different groups of VLCFA synthesis inhibitors. Detailed analyses of VLCFA composition in tissues of duckweed (Lemna paucicostata) indicated a specific inhibition of the known herbicide target 3 ketoacyl-CoA synthase (KCS). Inhibitor studies using a yeast expression system established for plant KCS proteins verified the potency of mefluidide as an inhibitor of plant KCS enzymes. It could be shown that the strength of inhibition varied for different KCS homologues. The Arabidopsis Cer6 protein, which induces a plant growth phenotype similar to mefluidide when knocked out, was one of the most sensitive KCS enzymes (Tresch et al., 2012).rnThe findings of my own work were combined with other publications reporting a successful identification of the MoA and primary target proteins of different compounds or compound classes.rnA revised three-tier approach for the MoA identification of phytoactive compounds is proposed. The approach consists of a 1st level aiming to address compound stability, uniformity of effects in different species, general cytotoxicity and the effect on common processes like transcription and translation. Based on these findings advanced studies can be defined to start the 2nd level of MoA characterisation, either with further phenotypic characterisation, starting a genetic screen or establishing a biochemical screen. At the 3rd level, enzyme assays or protein affinity studies should show the activity of the compound on the hypothesized target and should associate the in vitro effects with the in vivo profile of the compound.

Radio follow-up of the gamma-ray flaring gravitational lens B0218+357

B0218+357 è un blazar soggetto al lensing che si trova a z=0.944. Questo sistema consiste in due componenti compatte (A e B) e un anello di Einstein. Recentemente è stato associato ad una sorgente gamma soggetta a burst osservata con il satellite Fermi-LAT. Questo blazar ha mostrato una forte variabilità in banda γ da agosto a settembre del 2012. Gli episodi di variabilità osservati hanno consentito di misurare per la prima volta in banda gamma il ritardo temporale previsto dalla teoria del lensing gravitazionale. Le osservazioni in banda gamma sono state seguite da un programma di monitoring con il Very Long Baseline Array (VLBA) in banda radio con lo scopo di verificare l’esistenza di una correlazione tra l’emissione nelle due bande. In questa Tesi tali osservazioni radio sono state analizzate con lo scopo di studiare la variabilità di B0218+357 e, quindi, attestare la connessione tra l’emissione alle alte energie e quella in banda radio. L’obiettivo principale di questo lavoro di Tesi è quello di studiare l’evoluzione della densità di flusso, dell’indice spettrale e della morfologia delle immagini A e B e delle loro sottocomponenti. I dati analizzati sono stati ottenuti con l’interferometro VLBA a tre frequenze di osser- vazione: 2.3, 8.4 GHz (4 epoche con osservazioni simultanee alle due frequenze) e 22 GHz (16 epoche). Le osservazioni hanno coperto un periodo di circa due mesi, subito successivo al flare in banda gamma. La riduzione dei dati è stata effettuata con il pacchetto AIPS. Dall’analisi delle immagini, nella componente B è possibile riconoscere la tipica struttura nucleo-getto chiaramente a tutte e tre le frequenze, invece nella componente A questa struttura è identificabile solo a 22 GHz. A 2.3 e 8.4 GHz la risoluzione non è sufficiente a risolvere nucleo e getto della componente A e l’emissione diffusa risulta dominante. Utilizzando il metodo dello stacking sulle immagini a 2.3 GHz, è stato possibile rivelare le parti più brillanti dell’Einstein ring associato a questa sorgente. Questo è stato possibile poiché la sorgente non ha mostrato alcun segno di variabilità significativa né di struttura né di flusso nelle componenti. Quindi dall’analisi delle curve di luce delle due componenti A e B non è emersa una variabilità significativa chiaramente associabile al flare osservato in banda gamma. Per verificare questo risultato, le curve di luce ottenute sono state confrontate con le osservazioni del radio telescopio OVRO (15 GHz) nel periodo corrispondente alle nostre osservazioni. La curva di luce OVRO è risultata in pieno accordo con le curve di luce ottenute durante questo lavoro di tesi e ha confermato che B0218+257 non ha mostrato un’importante attività radio nel periodo delle osservazioni VLBA. In definitiva, la mancanza di variabilità radio associata a quella osservata nei raggi gamma può essere dovuta al fatto che la regione in cui si è originato il flare gamma è otticamente spessa alle lunghezze d’onda radio, oppure non esiste una precisa correlazione tra le due emissioni, rimanendo quindi un problema aperto da investigare.

La diagnostica molecolare nel laboratorio di patologia clinica veterinaria

La prima parte del nostro studio riguarda la tecnica LAMP (Loop-mediated isothermal amplification), una tecnica di amplificazione isotermica recentemente inventata (Notomi et al., 2000). Essa presenta notevoli vantaggi rispetto alle tradizionali PCR: non necessita di strumentazioni sofisticate come i termociclatori, può essere eseguita da personale non specializzato, è una tecnica altamente sensibile e specifica ed è molto tollerante agli inibitori. Tutte queste caratteristiche fanno sì che essa possa essere utilizzata al di fuori dei laboratori diagnostici, come POCT (Point of care testing), con il vantaggio di non dover gestire la spedizione del campione e di avere in tempi molto brevi risultati paragonabili a quelli ottenuti con la tradizionale PCR. Sono state prese in considerazione malattie infettive sostenute da batteri che richiedono tempi molto lunghi per la coltivazione o che non sono addirittura coltivabili. Sono stati disegnati dei saggi per la diagnosi di patologie virali che necessitano di diagnosi tempestiva. Altri test messi a punto riguardano malattie genetiche del cane e due batteri d’interesse agro-alimentare. Tutte le prove sono state condotte con tecnica real-time per diminuire il rischio di cross-contaminazione pur riuscendo a comprendere in maniera approfondita l’andamento delle reazioni. Infine è stato messo a punto un metodo di visualizzazione colorimetrico utilizzabile con tutti i saggi messi a punto, che svincola completamente la reazione LAMP dall’esecuzione in un laboratorio specializzato. Il secondo capitolo riguarda lo studio dal punto di vista molecolare di un soggetto che presenza totale assenza di attività mieloperossidasica all’analisi di citochimica automatica (ADVIA® 2120 Hematology System). Lo studio è stato condotto attraverso amplificazione e confronto dei prodotti di PCR ottenuti sul soggetto patologico e su due soggetti con fenotipo wild-type. Si è poi provveduto al sequenziamento dei prodotti di PCR su sequenziatore automatico al fine di ricercare la mutazione responsabile della carenza di MPO nel soggetto indicato.