Evaluation of a.c. conductivity of rubber ferrite composites from dielectric measurements

The effect of frequency, composition and temperature on the a.c. electrical conductivity were studied for the ceramic, Ni1–xZnxFe2O4, as well as the filler (Ni1–xZnxFe2O4) incorporated rubber ferrite composites (RFCs). Ni1–xZnxFe2O4 (where x varies from 0 to 1 in steps of 0×2) were prepared by usual ceramic techniques. They were then incorporated into a butyl rubber matrix according to a specific recipe. The a.c. electrical conductivity (sa.c.) calculations were carried out by using the data available from dielectric measurements and by employing a simple relationship. The a.c. conductivity values were found to be of the order of 10–3 S/m. Analysis of the results shows that sa.c. increases with increase of frequency and the change is same for both ceramic Ni1–xZnxFe2O4 and RFCs. sa.c. increases initially with the increase of zinc content and then decreases with increase of zinc. Same behaviour is observed for RFCs too. The dependence of sa.c. on the volume fraction of the magnetic filler was also studied and it was found that the a.c. conductivity of RFCs increases with increase of volume fraction of the magnetic filler. Temperature dependence of conductivity was studied for both ceramic and rubber ferrite composites. Conductivity shows a linear dependence with temperature in the case of ceramic samples

Variación de volumen sistólico como predictor de hipovolemia en pacientes pediátricos con choque séptico

El compromiso del sistema cardiovascular es frecuente en los pacientes en estado crítico, por tanto la monitorización hemodinámica es esencial para un tratamiento apropiado dirigido a objetivos terapéuticos en este grupo de pacientes. La monitorización hemodinámica del gasto cardíaco y la estimación del volumen intravascular son fundamentales para el manejo de los pacientes pediátricos en estado crítico, la medición del gasto cardíaco es uno de los principales elementos para evaluar la situación hemodinámica y la perfusión tisular de un paciente ayudando a dirigir el tratamiento y a monitorizar la respuesta clínica en pacientes con choque séptico. La hipovolemia es una causa común para la falla circulatoria en pacientes en condición crítica, el encontrar un método confiable para medición de precarga es importante para guiar la administración de líquidos. Tradicionalmente se han utilizado medidas de la volemia asociadas como la presión venosa central (PVC), frecuencia cardiaca (FC), presión arterial (PA) y el gasto urinario. Estos indicadores tienen grandes factores de distracción que hacen que su valor sea limitado y por tanto se tengan que buscar alternativas más confiables. En años recientes se han postulado parámetros dinámicos para la evaluación de la precarga, entre ellos uno de los mas ampliamente estudiado es la medición de la variabilidad de Volumen sistólico (VVS); Este valor se basa en el concepto de que durante la inspiración, la disminución del retorno venoso produce una disminución del Volumen sistólico, lo cual se manifiesta como una disminución en la onda de pulso; Por tanto en una situación de hipovolemia esta diferencia será mayor, dado que será más evidente la disminución del volumen al final de la diástole. En adultos este parámetro se ha convertido en una herramienta útil para evaluar estado de volumen de los pacientes que se encuentran en estado crítico y ha demostrado su utilidad para predecir respuesta a administración de fluidos en diferentes poblaciones de pacientes. En la actualidad no hay estudios en niños que comparen la medición de VVS contra dichas medidas tradicionales de volemia.

Polimorfismos del gen Butirilcolinesterasa responsables de reacciones adversas en pacientes consumidores de “cocaína”

La butirilcolinesterasa humana (BChE; EC 3.1.1.8) es una enzima polimórfica sintetizada en el hígado y en el tejido adiposo, ampliamente distribuida en el organismo y encargada de hidrolizar algunos ésteres de colina como la procaína, ésteres alifáticos como el ácido acetilsalicílico, fármacos como la metilprednisolona, el mivacurium y la succinilcolina y drogas de uso y/o abuso como la heroína y la cocaína. Es codificada por el gen BCHE (OMIM 177400), habiéndose identificado más de 100 variantes, algunas no estudiadas plenamente, además de la forma más frecuente, llamada usual o silvestre. Diferentes polimorfismos del gen BCHE se han relacionado con la síntesis de enzimas con niveles variados de actividad catalítica. Las bases moleculares de algunas de esas variantes genéticas han sido reportadas, entre las que se encuentra las variantes Atípica (A), fluoruro-resistente del tipo 1 y 2 (F-1 y F-2), silente (S), Kalow (K), James (J) y Hammersmith (H). En este estudio, en un grupo de pacientes se aplicó el instrumento validado Lifetime Severity Index for Cocaine Use Disorder (LSI-C) para evaluar la gravedad del consumo de “cocaína” a lo largo de la vida. Además, se determinaron Polimorfismos de Nucleótido Simple (SNPs) en el gen BCHE conocidos como responsables de reacciones adversas en pacientes consumidores de “cocaína” mediante secuenciación del gen y se predijo el efecto delos SNPs sobre la función y la estructura de la proteína, mediante el uso de herramientas bio-informáticas. El instrumento LSI-C ofreció resultados en cuatro dimensiones: consumo a lo largo de la vida, consumo reciente, dependencia psicológica e intento de abandono del consumo. Los estudios de análisis molecular permitieron observar dos SNPs codificantes (cSNPs) no sinónimos en el 27.3% de la muestra, c.293A>G (p.Asp98Gly) y c.1699G>A (p.Ala567Thr), localizados en los exones 2 y 4, que corresponden, desde el punto de vista funcional, a la variante Atípica (A) [dbSNP: rs1799807] y a la variante Kalow (K) [dbSNP: rs1803274] de la enzima BChE, respectivamente. Los estudios de predicción In silico establecieron para el SNP p.Asp98Gly un carácter patogénico, mientras que para el SNP p.Ala567Thr, mostraron un comportamiento neutro. El análisis de los resultados permite proponer la existencia de una relación entre polimorfismos o variantes genéticas responsables de una baja actividad catalítica y/o baja concentración plasmática de la enzima BChE y algunas de las reacciones adversas ocurridas en pacientes consumidores de cocaína.

Caracterización de la exposición ocupacional a formaldehído en trabajadores del sector salud y educación en Colombia 2004-2013.

El Formaldehído es una sustancia química de amplio uso a nivel mundial con efectos documentados en personas expuestas entre los cuales se destacan irritación de la piel, mucosas, tracto respiratorio y ojos. Según la Agencia Internacional para la Investigación del Cáncer (IARC) el formaldehido se encuentra clasificado en el grupo 1 como agente cancerígeno con suficiente evidencia de producir neoplasias en humanos. Los sectores industriales en Colombia que utilizan de forma frecuente el formaldehído incluyen los fabricantes de maderas, los servicios funerarios, y los sectores de salud y educación. El presente estudio de corte transversal pretende, con base en mediciones históricas (2004-2013) construir un perfil de exposición a formaldehído en trabajadores vinculados al sector de salud y educación en Colombia, divididos y analizados según actividades de trabajo similares (Patólogos, Histotecnólogos, Auxiliares de laboratorio, Docentes y Estudiantes), con el fin de establecer una línea base de diagnóstico para la orientación acciones dirigidas al control del riesgo. Con base en los hallazgos y soportados en estimadores estadísticos aplicables a los grupos de exposición, en general existe un tendencia de no conformidad al comparar los resultados aplicables con valores de referencia de larga duración definidos para el agente por autoridades internacionales. De forma complementaria se encontraron brechas significativas respecto a la implementación de controles administrativos y técnicos que sugieren circunstancias de exposición no controladas en los colectivos de interés.

Estimating drizzle drop size and precipitation rate using two-colour lidar measurements

A method to estimate the size and liquid water content of drizzle drops using lidar measurements at two wavelengths is described. The method exploits the differential absorption of infrared light by liquid water at 905 nm and 1.5 μm, which leads to a different backscatter cross section for water drops larger than ≈50 μm. The ratio of backscatter measured from drizzle samples below cloud base at these two wavelengths (the colour ratio) provides a measure of the median volume drop diameter D0. This is a strong effect: for D0=200 μm, a colour ratio of ≈6 dB is predicted. Once D0 is known, the measured backscatter at 905 nm can be used to calculate the liquid water content (LWC) and other moments of the drizzle drop distribution. The method is applied to observations of drizzle falling from stratocumulus and stratus clouds. High resolution (32 s, 36 m) profiles of D0, LWC and precipitation rate R are derived. The main sources of error in the technique are the need to assume a value for the dispersion parameter μ in the drop size spectrum (leading to at most a 35% error in R) and the influence of aerosol returns on the retrieval (≈10% error in R for the cases considered here). Radar reflectivities are also computed from the lidar data, and compared to independent measurements from a colocated cloud radar, offering independent validation of the derived drop size distributions.

Volume-based size distribution of accumulation and coarse particles (PM0.1–10) from cooking fume during oil heating

Particulate matter generated during the cooking process has been identified as one of the major problems of indoor air quality and indoor environmental health. Reliable assessment of exposure to cooking-generated particles requires accurate information of emission characteristics especially the size distribution. This study characterizes the volume/mass-based size distribution of the fume particles at the oil-heating stage for the typical Chinese-style cooking in a laboratory kitchen. A laser-diffraction size analyzer is applied to measure the volume frequency of fume particles ranged from 0.1 to 10 μm, which contribute to most mass proportion in PM2.5 and PM10. Measurements show that particle emissions have little dependence on the types of vegetable oil used but have a close relationship with the heating temperature. It is found that volume frequency of fume particles in the range of 1.0–4.0 μm accounts for nearly 100% of PM0.1–10 with the mode diameter 2.7 μm, median diameter 2.6 μm, Sauter mean diameter 3.0 μm, DeBroukere mean diameter 3.2 μm, and distribution span 0.48. Such information on emission characteristics obtained in this study can be possibly used to improve the assessment of indoor air quality due to PM0.1–10 in the kitchen and residential flat.

A time-invariant visco-elastic windkessel model relating blood flow and blood volume

The difference between the rate of change of cerebral blood volume (CBV) and cerebral blood flow (CBF) following stimulation is thought to be due to circumferential stress relaxation in veins (Mandeville, J.B., Marota, J.J.A., Ayata, C., Zaharchuk, G., Moskowitz, M.A., Rosen, B.R., Weisskoff, R.M., 1999. Evidence of a cerebrovascular postarteriole windkessel with delayed compliance. J. Cereb. Blood Flow Metab. 19, 679–689). In this paper we explore the visco-elastic properties of blood vessels, and present a dynamic model relating changes in CBF to changes in CBV. We refer to this model as the visco-elastic windkessel (VW) model. A novel feature of this model is that the parameter characterising the pressure–volume relationship of blood vessels is treated as a state variable dependent on the rate of change of CBV, producing hysteresis in the pressure–volume space during vessel dilation and contraction. The VW model is nonlinear time-invariant, and is able to predict the observed differences between the time series of CBV and that of CBF measurements following changes in neural activity. Like the windkessel model derived by Mandeville, J.B., Marota, J.J.A., Ayata, C., Zaharchuk, G., Moskowitz, M.A., Rosen, B.R., Weisskoff, R.M., 1999. Evidence of a cerebrovascular postarteriole windkessel with delayed compliance. J. Cereb. Blood Flow Metab. 19, 679–689, the VW model is primarily a model of haemodynamic changes in the venous compartment. The VW model is demonstrated to have the following characteristics typical of visco-elastic materials: (1) hysteresis, (2) creep, and (3) stress relaxation, hence it provides a unified model of the visco-elastic properties of the vasculature. The model will not only contribute to the interpretation of the Blood Oxygen Level Dependent (BOLD) signals from functional Magnetic Resonance Imaging (fMRI) experiments, but also find applications in the study and modelling of the brain vasculature and the haemodynamics of circulatory and cardiovascular systems.

Geiger tube coincidence counter for lower atmosphere radiosonde measurements

Atmospheric profiles of cosmic rays and radioactivity can be obtained using adapted meteorologi- cal radiosondes, for which Geiger tubes remain widely used detectors. Simultaneous triggering of two tubes provides an indication of energetic events. As, however, only small volume detectors can be carried, the event rate is small, which, due to the rapid balloon ascent, cannot be circumvented using long averaging periods. To derive count rates at low altitudes, a microcontroller is used to de- termine the inter-event time. This yields estimates of the coincidence rate below 5 km, where the coincidence rate is too small to determine solely by event counting

In situ and remote-sensing measurements of the mean microphysical and optical properties of industrial pollution aerosol during ADRIEX

We present a summary of the principal physical and optical properties of aerosol particles using the FAAM BAE-146 instrumented aircraft during ADRIEX between 27 August and 6 September 2004, augmented by sunphotometer, lidar and satellite retrievals. Observations of anthropogenic aerosol, principally from industrial sources, were concentrated over the northern Adriatic Sea and over the Po Valley close to the aerosol sources. An additional flight was also carried out over the Black Sea to compare east and west European pollution. Measurements show the single-scattering albedo of dry aerosol particles to vary considerably between 0.89 and 0.97 at a wavelength of 0.55 μm, with a campaign mean within the polluted lower free troposphere of 0.92. Although aerosol concentrations varied significantly from day to day and during individual days, the shape of the aerosol size distribution was relatively consistent through the experiment, with no detectable change observed over land and over sea. There is evidence to suggest that the pollution aerosol within the marine boundary layer was younger than that in the elevated layer. Trends in the aerosol volume distribution show consistency with multiple-site AERONET radiometric observations. The aerosol optical depths derived from aircraft measurements show a consistent bias to lower values than both the AERONET and lidar ground-based radiometric observations, differences which can be explained by local variations in the aerosol column loading and by some aircraft instrumental artefacts. Retrievals of the aerosol optical depth and fine-mode (<0.5 μm radius) fraction contribution to the optical depth using MODIS data from the Terra and Aqua satellites show a reasonable level of agreement with the AERONET and aircraft measurements.

Technical note: how accurate can stalagmite formation temperatures be determined using vapour bubble radius measurements in fluid inclusions?

Stalagmites are natural archives containing detailed information on continental climate variability of the past. Microthermometric measurements of fluid inclusion homogenisation temperatures allow determination of stalagmite formation temperatures by measuring the radius of stable laser-induced vapour bubbles inside the inclusions. A reliable method for precisely measuring the radius of vapour bubbles is presented. The method is applied to stalagmite samples for which the formation temperature is known. An assessment of the bubble radius measurement accuracy and how this error influences the uncertainty in determining the formation temperature is provided. We demonstrate that the nominal homogenisation temperature of a single inclusion can be determined with an accuracy of ±0.25 °C, if the volume of the inclusion is larger than 105 μm3. With this method, we could measure in a proof-of-principle investigation that the formation temperature of 10–20 yr old inclusions in a stalagmite taken from the Milandre cave is 9.87 ± 0.80 °C, while the mean annual surface temperature, that in the case of the Milandre cave correlates well with the cave temperature, was 9.6 ± 0.15 °C, calculated from actual measurements at that time, showing a very good agreement. Formation temperatures of inclusions formed during the last 450 yr are found in a temperature range between 8.4 and 9.6 °C, which corresponds to the calculated average surface temperature. Paleotemperatures can thus be determined within ±1.0 °C.

Rayleigh scattering by hexagonal ice crystals and the interpretation of dual-polarisation radar measurements

Dual-polarisation radar measurements provide valuable information about the shapes and orientations of atmospheric ice particles. For quantitative interpretation of these data in the Rayleigh regime, common practice is to approximate the true ice crystal shape with that of a spheroid. Calculations using the discrete dipole approximation for a wide range of crystal aspect ratios demonstrate that approximating hexagonal plates as spheroids leads to significant errors in the predicted differential reflectivity, by as much as 1.5 dB. An empirical modification of the shape factors in Gans's spheroid theory was made using the numerical data. The resulting simple expressions, like Gans's theory, can be applied to crystals in any desired orientation, illuminated by an arbitrarily polarised wave, but are much more accurate for hexagonal particles. Calculations of the scattering from more complex branched and dendritic crystals indicate that these may be accurately modelled using the new expression, but with a reduced permittivity dependent on the volume of ice relative to an enclosing hexagonal prism.

Effects of single or repeated amphetamine treatment and withdrawal on lung allergic inflammation in rats

The effects of single or repeated amphetamine (AMPH) treatment and those of AMPH withdrawals on immune-mediated lung inflammatory response were studied in rats. Two experiments were done. In the first, rats egg-albumin (OVA) sensitized were singularly or repeatedly (21 days, once daily) treated with AMPH (1.0 mg/kg) or with a similar number and volume of 0.9% NaCl. The OVA aerosol challenge was performed 12 h after the single or last repeated AMPH treatment and also 72 and 120 h after AMPH withdrawal. In the second experiment, the effects of reserpine (1.0 mg/kg/day for 5 consecutive days) on single AMPH actions on lung allergic response of rats were analyzed. Single and repeated AMPH treatment induced opposite actions on Bronchoalveolar lavage fluid (BAL) cellularity of allergic rats: single treatment decreased and repeated treatment increased the total number of cells as well as those of macrophages, neutrophils and eosinophils. Our data also showed that single but not repeated AMPH treatment decreased the number of neutrophils, monocytes and lymphocytes in the peripheral blood, and increased the total number of bone marrow cells in rats sensitized and challenged with OVA. Furthermore, it was shown that reserpine treatment precluded the effects of single AMPH treatment on cellular migration to the lung of OVA-sensitized and challenged rats. It was concluded that AMPH effects on lung inflammatory response and cell recruitment to the lung in allergic rats rely at least partially on corticosterone serum levels. The possible involvement of vesicular monoamine transporter type 2 (VMAT2) with these observed effects was discussed. (c) 2008 Elsevier B.V. All rights reserved.

Dendrimer-assisted immobilization of alcohol dehydrogenase in nanostructured films for biosensing: Ethanol detection using electrical capacitance measurements

The selective determination of alcohol molecules either in aqueous solutions or in vapor phase is of great importance for several technological areas. In the last years, a number of researchers have reported the fabrication of highly sensitive sensors for ethanol detection, based upon specific enzymatic reactions occurring at the surface of enzyme-containing electrodes. In this study, the enzyme alcohol dehydrogenase (ADH) was immobilized in a layer-by-layer fashion onto Au-interdigitated electrodes (IDEs), in conjunction with layers of PAMAM dendrimers. The immobilization process was followed in Teal time using quartz crystal microbalance (QCM), indicating that an average mass of 52.1 ng of ADH was adsorbed at each deposition step. Detection was carried out using a novel strategy entirely based upon electrical capacitance measurements, through which ethanol could be detected at concentrations of 1 part per million by volume (ppmv). (C) 2007 Elsevier B.V. All rights reserved.

Influência do modo ventilatório no desempenho funcional dos enxertos pulmonares pós-transplante em modelo canino : ventilção controlada a volume versus ventilação controlada a pressão

O conhecimento dos riscos e conseqüências da lesão pulmonar induzida pela ventilação mecânica mudou a filosofia da terapia respiratória e tem influenciado nas recomendações e padronizações de seu uso. A influência dos diferentes modos ventilatórios não tem sido estudada em transplante de pulmão. O presente estudo teve como objetivo comparar a influência da ventilação controlada a volume (VCV) com a ventilação controlada a pressão (PCV) no desempenho funcional dos enxertos pulmonares, em modelo canino de transplante pulmonar unilateral utilizando-se doadores após três horas de parada cardiocirculatória. Quinze cães foram randomizados em dois grupos: oito cães foram alocados para o Grupo VCV e sete cães para o Grupo PCV. Cinco cães não completaram o período de avaliação pós-transplante, os dez animais restantes, grupo VCV (n= 5) e grupo PCV (n=5), foram avaliados durante 360 min após o término do transplante pulmonar. O desempenho funcional dos enxertos foi estudado através da avaliação da mecânica respiratória, trocas gasosas e das alterações histopatológicas. Não foram encontradas diferenças significativas em nenhuma das variáveis da mecânica respiratória estudadas (pressões de pico inspiratória- PPI; pressões de platô- PPLAT ; pressões médias de vias aéreas – Pmédia; complacências dinâmica- Cdyn e estática- Cst); da oxigenação, pressão parcial de oxigênio no sangue arterial e venoso misto (PaO2, PvO2); a diferença entre a saturação da hemoglobina no sangue arterial e no sangue venoso misto (ΔSO2); a pressão parcial de dióxido de carbono no sangue arterial e no sangue venoso misto (PaCO2, PvO2). As alterações histopatológicas encontradas nos pulmões dos animais foram compatíveis com o padrão de lesão pulmonar aguda. As alterações histológicas de padrão inespecífico não tiveram nenhuma correlação com o modo ventilatório. Este estudo demonstra que os modos ventilatórios estudados não influenciam as respostas dos enxertos pulmonares à lesão de isquemia reperfusão que se estabelece precocemente neste modelo experimental até 6 horas de reperfusão pulmonar pós-transplante unilateral.

Origem física das curvas sigmoidais respiratórias pressão-volume: recrutamento alveolar e elasticidade não-linear

An important unsolved problem in medical science concerns the physical origin of the sigmoidal shape of pressure volume curves of healthy (and some unhealthy) lungs. Such difficulties are expected because the lung, which is the most important structure in the respiratory system, is extremely complex. Its rheological properties are unknown and seem to depend on phenomena occurring from the alveolar scale up to the thoracic scale. Conventional wisdom holds that linear response, i.e., Hooke s law, together with alveolar overdistention, play a dominant role in respiration, but such assumptions cannot explainthe crucial empirical sigmoidal shape of the curves. In this doctorate thesis, we propose an alternative theory to solve this problem, based on the alveolar recruitment together with the nonlinear elasticity of the alveoli. This theory suggests that recruitment may be the predominant factor shaping these curves in the entire range of pressures normally employed in experiments. The proposed model correctly predicts the observed sigmoidal pressure volume curves, allowing us to discuss adequately the importance of this result, as well as its implications for medical practice