Investigation of vertical radiation loss for whispering-gallery modes in 3-D microresonators by FDTD simulation

The vertical radiation loss of three-dimensional (3-D) microresonators is investigated by 3-D finite-difference time-domain (FDTD) simulation. The simulation shows that the vertical radiation causes an important loss in the microresonators with weak waveguiding, and result in decrease of the quality factors (Q-factors) of whispering-gallery (WG) modes. Through the simulation, we find that TM-like modes have much weaker vertical radiation loss than TE-like modes. High Q-factor TM-like modes are observed in the 3-D microresonators with weak vertical waveguiding, but the Q-factors of TE-like modes decrease greatly.

Continuous-wave electrically injected InP/GaInAsP equilateral-triangle-resonator lasers

Equilateral-triangle-resonator (ETR) microlasers with an output waveguide connected to one of the vertices of the ETR are fabricated using standard photolithography and inductively-coupled-plasma etching techniques. Continuous-wave electrically injected 1550 nm ETR laser with side length ranged from 15 to 30 tm are realized at room temperature.

Analysis of leakage current in GaAs micro-solar cell arrays

The output characteristics of micro-solar cell arrays are analyzed on the basis of a modified model in which the shunt resistance between cell lines results in current leakage. The modification mainly consists of adding a shunt resistor network to the traditional model. The obtained results agree well with the reported experimental results. The calculation results demonstrate that leakage current in substrate affects seriously the performance of GaAs micro- solar cell arrays. The performance of arrays can be improved by reducing the number of cells per line. In addition, at a certain level of integration, an appropriate space occupancy rate of the single cell is recommended for ensuring high open circuit voltages, and it is more appropriate to set the rates at 80%-90% through the calculation.

Prediction of simultaneously large and opposite generalized Goos-Hanchen shifts for TE and TM light beams in an asymmetric double-prism configuration

It is predicted that large and opposite generalized Goos-Hanchen (GGH) shifts may occur simultaneously for TE and TM light beams upon reflection from an asymmetric double-prism configuration when the angle of incidence is below but near the critical angle for total reflection, which may lead to interesting applications in optical devices and integrated optics. Numerical simulations show that the magnitude of the GGH shift can be of the order of beam's width.

M_2RSbO_6:R~(3+)复合氧化物的合成组成结构和性能的研究(M = Ba、Sr、Ca, R = La、Gd、Y、Bi, R' = Sm、Eu、Dy、Ho、Er、Tm)

对于稀土与非稀土所组成的二元复合氧化物的研究国外已有较多的报导。但是，对于稀土和锑的复合氧化物只是近年来才开始有些研究工作。含锑与稀土的多元复合氧化物的报导就更少。本文在我们实验室张静筠等人三元复合氧化物研究的基础上，开展Mo—Sb_2O_5—R_2O_3—R'_2O_3—Bi_2O_3多元体系的研究工作，这对于我国丰产元素稀土和锑的应用以及利用Bi~(3+)的激活与敏化将是有益的。本文按Thornton等人的方法合成了Ba_2BiSbO_6，Ba_2GdSbO_6，按EγΦECEHKO等人的方法合成了M_2RSbO_6 (M = Ba、Sr、Ca, R = La Y)。并以M_2RSbO_6为基质，掺Sm~(3+)、Eu~(3+)、Dy~(3+)、Ho~(3+)、Er~(3+)、Tm~(3+)和Bi~(3+)，研究它们的化学组成，晶体结构与发光性能的关系及规律，Bi~(3+)的荧光和敏作用。同时研究了它们的磁学和热学性能。化学组成的分析结果表明，计算的含量与实验测得的含量符合较好，说明化学反应是按化学计量比进行的。通过X-射线粉沫物相分析和晶胞参数的理论计算确定M_2RSbO_6(M = Ba、Sr、R = La、Y、Gd、Bi)复合氧化物是属于立方钙钛太型化合物。空间群为Fm3m，点群为Oh。用计算机计算了Ca_2YSbO_6的晶胞参数并结合荧光光谱分析确定它属于畸变的单斜钙钛矿，空间群为P_(21)。用磁天平测量了样品M_2RSbO_6 (M = Ba、Sr、Ca; R = Gd、Y、Bi)的磁化率。除Ba_2GdSbO_6是顺磁性物质外共余的都是反磁性的物质。按所用原料Sb_2O_5计算的磁化率与测量值符合较好，表明在所研究的M_2RSbO_6化合物中锑是正五价的。用热重热差分析仪测量了样品在反应中的热性能，观察到在化合物形成的过程中所用原料Sb_2O_3大约在520 ℃左右氧化变为Sb_2O_5。除所用原料碳酸盐分解外没有挥发性的物质，这就进一步证明化学组成分析和磁化率测量的结果是正确的。光学测量的结果表明，所有的磷光体随着激活离子浓度的不同其光谱都发生规律性的变化。对于不同Eu~(3+)浓度的Ba_2YSbO_6:Eu~(3+)和Br_2YSbO_6:Eu~(3+), Bi~(3+)体系用254nm激发时均能观察到Eu~(3+)于595nm的尖峰发射。用基质和Bi~(3+)的激发峰325nm激发时，明显地看到敏化剂Bi~(3+)到Eu~(3+)的能量传递，使Eu~(3+)于595nm的发射大大增强，我们认为Bi~(3+)对Eu~(3+)的敏化作用是由于基质和Bi~(3+)的~1S。→ 3P_1的跃迁吸收了激发的能量，然后无辐射弛豫到Eu~(3+)的激发态~5D_0，产生~5D_0 → 7F_1的磁偶极跃迁。对于不同Eu~(3+)浓度的Sr_2YSbO_6:Eu~(3+)和Sr_2YSbO_6:Eu~(3+), Bi~(3+)体系用245nm激发时均能观察到Eu~(3+)于595nm的尖峰发射。用基质和Bi~(3+)的激发峰335nm激发时，观察到基质和Bi~(3+)对Eu~(3+)具有某种能量传递。敏化作用机理与上述的Ba_2YSbO_6:Eu~(3+)和Ba_2YSbO_6:Eu~(3+), Bi~(3+)体系相同。对于不同Eu~(3+)浓度的Ca_2YSbO_6:Eu~(3+)和Ca_2YSbO_6:Eu~(3+), Bi~(3+)体系用396nm激发时，均能观察到Eu~(3+)于613nm很强的尖峰发射。用基质和Bi~(3+)的激发峰313nm激发时，见到Bi~(3+)和基质对Eu~(3+)具有某种能量传递，这种敏化作用主要是由于基质和Bi~(3+)的3P_1 → ~1S_0的400nm的宽带发射和Eu~(3+)的~7F_0 → ~5L_6的396nm的吸收相匹配产生~5L_6→~5D_0→~7F_2的跃迁。通过对激发光谱和荧光光谱的分析给出了Ca_2Y_(0.96)Eu_(0.04)SbO_6的能级图，从实验上可见，Eu~(3+)的发光强烈地依赖于钙钛矿的结构，当Eu~(3+)在空间群为Fm3m 的Ba_2YSbO_6和Sr_2YSbO_6中处于Oh点对称性时，主要是~5D_0 → ~7F_1的磁偶极跃迁。当Eu~(3+)在空间群为P_(21)的单斜钙钛矿中时，主要是~5D_0 → ~7F_2的电偶极跃迁。对于不同掺杂浓度M_2YSbO_6:R~(13+)(M = Ba、Ca; R' = Sm、Dy、Ho、Er、Tm)体系，通过激发和荧光光谱的研究，合理地确定了谱项。发现基质对Sm~(3+)、Dy~(3+)、Ho~(3+)具有敏化作用。对不同Bi~(3+)浓度的Ca_2YSbO_6:Bi~(3+)，由激发和荧光光谱可见Bi~(3+)具有二个激发带，第一激发带位于240nm处相当于~1S_0 → ~1P_1的跃迁，第二激发带位于315nm处相当于~1S_0 → ~3P_1的跃迁。有一个很强的兰紫色发射位于400nm处相当于~3P_1 →~1S_0的跃迁。

GAAS/GAALAS GRADED INDEX SEPARATE CONFINEMENT SINGLE QUANTUM-WELL SINGLE-MODE WAVE-GUIDE ELECTROABSORPTION LIGHT-MODULATOR

A GaAs/GaAlAs graded-index separate confinement single quantum well heterostructure single-mode ridge waveguide electroabsorption modulator was fabricated and investigated. For the modulator with a quantum well width of 100 angstrom and device length of 700-mu-m, an on/off ratio of 29.7 dB and estimated absorption insertion loss of 3 dB were obtained for TE polarised light with wavelength 8650 angstrom, and for TM polarisation the on/off ratio was 28.5 dB. With a switching voltage of 1 V, an on/off ratio of 15 dB was achieved. Photocurrent spectra exhibited a red shift of 600 angstrom of the absorption edge when the voltage applied to the PIN diode was varied from 0.5 to -7 V. The corresponding shift of the room temperature exciton peak energy was 96 meV.

A High-Efficiency Fiber-to-Waveguide Coupler with Low Polarization Dependence Using a Diluted Waveguide in InP Substrate with a 1.55μm Wavelength

We propose a fiber-to-waveguide coupler for side-illuminated p-i-n photodiodes to obtain high responsivity and low polarization dependence that is grown on InP substrate and is suitable for surface hybrid integration in low cost modules. The fiber-to-waveguide coupler is based on a diluted waveguide,which is composed of ten periods of undoped 120nm InP/80nm InGaAsP （1.05μm bandgap） multiple layers. Using the semi-vectorial three dimensional beam propagation method （BPM） with the central difference scheme,the coupling efficiency of fiber-to-waveguide under different conditions is simulated and studied,and the optimized conditions for fiber-to-waveguide coupling are obtained. For TE-like and TM-like modes,the calculated maximum coupling efficiency is higher than 94% and 92% ,respectively. The calculated polarization dependence is less than 0. ldB,showing good polarization independence.

BF＋对（29）Si＋注入GaAs层的影响

于2010-11-23批量导入

A novel polarization-insensitive semiconductor optical amplifier structure with large 3dB bandwidth

A novel approach to achieving a polarization-insensitive semiconductor optical amplifier is presented. The active layer consists of graded tensile strained bulk-like structure. which can not only enhance TM mode material gain and further realize polarization-insensitivity, but also get a large 3dB bandwidth due to different strain introduced into the active layer. 3dB bandwidth more than 40nm. 65nm has been obtained in die experiment and theory, respectively. The characteristics of such polarization insensitive structure have been analyzed, The influence of the amount of strain and of the thickness of strain layer on the polarization insensitivity has been discussed.

Design and fabrication of polarization-insensitive 1550 mm semiconductor optical amplifiers

Polarization-insensitive semiconductor optical amplifiers (SOA's) with tensile-strained multi-quantum-wells as actice regions are designed and fabricated. The 6x6 Luttinger-Kohn model and Bir-Pikus Hamiltonian are employed to calculate the valence subband structures of strained quantum wells, and then a Lorentzian line-shape function is combined to calculate the material gain spectra for TE and TM modes. The device structure for polarization insensitive SOA is designed based on the materialde gain spectra of TE and TM modes and the gain factors for multilayer slab waveguide. Based on the designed structure parameters, we grow the SOA wafer by MOCVD and get nearly magnitude of output power for TE and TM modes from the broad-area semiconductor lasers fabricated from the wafer.

Study on optical band gap of boron-doped nc-Si : H film

The optical band gap (E-g) of the boron (B)-doped hydrogenated nano-crystalline silicon (nc-Si:H) films fabricated using plasma enhanced chemical vapor deposition (PECVD) was investigated in this work. The transmittance of the films were measured by spectrophotometric and the E-g was evaluated utilizing three different relations for comparison, namely: alphahnu=C(hnu-E-g)(3), alphahnu=B-0(hnu-E-g)(2), alphahnu=C-0(hnu-E-g)(2). Result showed that E-g decreases with the increasing of Boron doping ratio, hydrogen concentration, and substrate's temperature (T-s), respectively. E-g raises up with rf power density (P-d) from 0.45W.cm(-2) to 0.60w.cm(-2) and then drops to the end. These can be explained for E-g decreases with disorder in the films.