DCM Boost interleaved converter for operation in AC and DC to trolleybus application

This paper is based on the development and experimental analysis of a DCM Boost interleaved converter suitable for application in traction systems of electrical vehicles pulled by electrical motors (Trolleybus), which are powered by urban DC or AC distribution networks. This front-end structure is capable of providing significant improvements in trolleybuses systems and in the urban distribution network costs, and efficiency. The architecture of proposed converter is composed by five boost power cells in interleaving connection, operating in discontinuous conduction mode. Furthermore, the converter can operate as AC-DC converter, or as DC-DC converter providing the proper DC output voltage range required by DC or AC adjustable speed drivers. Therefore, when supplied by single-phase AC distribution networks, and operating as AC-DC converter, it is capable to provide high power factor, reduced harmonic distortion in the input current, complying with the restrictions imposed by the IEC 61000-3-4 standards. The digital controller has been implemented using a low cost FPGA and developed totally using a hardware description language VHDL and fixed point arithmetic. Thus, two control strategies are evaluated considering the compliance with input current restrictions imposed by IEC 61000-3-4 standards, the regular PWM modulation and a current correction PWM modulation. In order to verify the feasibility and performance of the proposed system, experimental results from a 15 kW low power scale prototype are presented, operating in DC and AC conditions.

A VHDL-based protocol controller for NCAP processors

This work presents the development of an IEEE 1451.2 protocol controller based on a low-cost FPGA that is directly connected to the parallel port of a conventional personal computer. In this manner it is possible to implement a Network Capable Application Processor (NCAP) based on a personal computer, without parallel port modifications. This approach allows supporting the ten signal lines of the 10-wire IEEE 1451.2 Transducer Independent Interface (TII), that connects the network processor to the Smart Transducer Interface Module (STIM) also defined in the IEEE 1451.2 standard. The protocol controller is connected to the STIM through the TII's physical interface, enabling the portability of the application at the transducer and network processor level. The protocol controller architecture was fully developed in VHDL language and we have projected a special prototype configured in a general-purpose programmable logic device. We have implemented two versions of the protocol controller, which is based on IEEE 1451 standard, and we have obtained results using simulation and experimental tests. (c) 2008 Elsevier B.V. All rights reserved.

Proposta e implementação de uma arquitetura reconfigurável híbrida para aplicações baseadas em fluxo de dados

The increase of applications complexity has demanded hardware even more flexible and able to achieve higher performance. Traditional hardware solutions have not been successful in providing these applications constraints. General purpose processors have inherent flexibility, since they perform several tasks, however, they can not reach high performance when compared to application-specific devices. Moreover, since application-specific devices perform only few tasks, they achieve high performance, although they have less flexibility. Reconfigurable architectures emerged as an alternative to traditional approaches and have become an area of rising interest over the last decades. The purpose of this new paradigm is to modify the device s behavior according to the application. Thus, it is possible to balance flexibility and performance and also to attend the applications constraints. This work presents the design and implementation of a coarse grained hybrid reconfigurable architecture to stream-based applications. The architecture, named RoSA, consists of a reconfigurable logic attached to a processor. Its goal is to exploit the instruction level parallelism from intensive data-flow applications to accelerate the application s execution on the reconfigurable logic. The instruction level parallelism extraction is done at compile time, thus, this work also presents an optimization phase to the RoSA architecture to be included in the GCC compiler. To design the architecture, this work also presents a methodology based on hardware reuse of datapaths, named RoSE. RoSE aims to visualize the reconfigurable units through reusability levels, which provides area saving and datapath simplification. The architecture presented was implemented in hardware description language (VHDL). It was validated through simulations and prototyping. To characterize performance analysis some benchmarks were used and they demonstrated a speedup of 11x on the execution of some applications

Geração automática de hardware apartir de especificações formais: estendendo uma abordagem de tradução

A remoção de inconsistências em um projeto é menos custosa quando realizadas nas etapas iniciais da sua concepção. A utilização de Métodos Formais melhora a compreensão dos sistemas além de possuir diversas técnicas, como a especificação e verificação formal, para identificar essas inconsistências nas etapas iniciais de um projeto. Porém, a transformação de uma especificação formal para uma linguagem de programação é uma tarefa não trivial. Quando feita manualmente, é uma tarefa passível da inserção de erros. O uso de ferramentas que auxiliem esta etapa pode proporcionar grandes benefícios ao produto final a ser desenvolvido. Este trabalho propõe a extensão de uma ferramenta cujo foco é a tradução automática de especificações em CSPm para Handel-C. CSP é uma linguagem de descrição formal adequada para trabalhar com sistemas concorrentes. Handel-C é uma linguagem de programação cujo resultado pode ser compilado diretamente para FPGA's. A extensão consiste no aumento no número de operadores CSPm aceitos pela ferramenta, permitindo ao usuário definir processos locais, renomear canais e utilizar guarda booleana em escolhas externas. Além disto, propomos também a implementação de um protocolo de comunicação que elimina algumas restrições da composição paralela de processos na tradução para Handel-C, permitindo que a comunicação entre múltiplos processos possa ser mapeada de maneira consistente e que a mesma somente ocorra quando for autorizada.

Geração automática de hardware a partir de especificações formais: estendendo uma abordagem de tradução

Removing inconsistencies in a project is a less expensive activity when done in the early steps of design. The use of formal methods improves the understanding of systems. They have various techniques such as formal specification and verification to identify these problems in the initial stages of a project. However, the transformation from a formal specification into a programming language is a non-trivial task and error prone, specially when done manually. The aid of tools at this stage can bring great benefits to the final product to be developed. This paper proposes the extension of a tool whose focus is the automatic translation of specifications written in CSPM into Handel-C. CSP is a formal description language suitable for concurrent systems, and CSPM is the notation used in tools support. Handel-C is a programming language whose result can be compiled directly into FPGA s. Our extension increases the number of CSPM operators accepted by the tool, allowing the user to define local processes, to rename channels in a process and to use Boolean guards on external choices. In addition, we also propose the implementation of a communication protocol that eliminates some restrictions on parallel composition of processes in the translation into Handel-C, allowing communication in a same channel between multiple processes to be mapped in a consistent manner and that improper communication in a channel does not ocurr in the generated code, ie, communications that are not allowed in the system specification

Algoritmos e Arquiteturas VLSI para Detectores MIMO com Decisão Suave

The use of Multiple Input Multiple Output (MIMO) systems has permitted the recent evolution of wireless communication standards. The Spatial Multiplexing MIMO technique, in particular, provides a linear gain at the transmission capacity with the minimum between the numbers of transmit and receive antennas. To obtain a near capacity performance in SM-MIMO systems a soft decision Maximum A Posteriori Probability MIMO detector is necessary. However, such detector is too complex for practical solutions. Hence, the goal of a MIMO detector algorithm aimed for implementation is to get a good approximation of the ideal detector while keeping an acceptable complexity. Moreover, the algorithm needs to be mapped to a VLSI architecture with small area and high data rate. Since Spatial Multiplexing is a recent technique, it is argued that there is still much room for development of related algorithms and architectures. Therefore, this thesis focused on the study of sub optimum algorithms and VLSI architectures for broadband MIMO detector with soft decision. As a result, novel algorithms have been developed starting from proposals of optimizations for already established algorithms. Based on these results, new MIMO detector architectures with configurable modulation and competitive area, performance and data rate parameters are here proposed. The developed algorithms have been extensively simulated and the architectures were synthesized so that the results can serve as a reference for other works in the area

Arquitetura hardware/software de um núcleo NCAP segundo o padrão IEEE 1451.1: uma prova de conceito

Os sensores inteligentes são dispositivos que se diferenciam dos sensores comuns por apresentar capacidade de processamento sobre os dados monitorados. Eles tipicamente são compostos por uma fonte de alimentação, transdutores (sensores e atuadores), memória, processador e transceptor. De acordo com o padrão IEEE 1451 um sensor inteligente pode ser dividido em módulos TIM e NCAP que devem se comunicar através de uma interface padronizada chamada TII. O módulo NCAP é a parte do sensor inteligente que comporta o processador. Portanto, ele é o responsável por atribuir a característica de inteligência ao sensor. Existem várias abordagens que podem ser utilizadas para o desenvolvimento desse módulo, dentre elas se destacam aquelas que utilizam microcontroladores de baixo custo e/ou FPGA. Este trabalho aborda o desenvolvimento de uma arquitetura hardware/software para um módulo NCAP segundo o padrão IEEE 1451.1. A infra-estrutura de hardware é composta por um driver de interface RS-232, uma memória RAM de 512kB, uma interface TII, o processador embarcado NIOS II e um simulador do módulo TIM. Para integração dos componentes de hardware é utilizada ferramenta de integração automática SOPC Builder. A infra-estrutura de software é composta pelo padrão IEEE 1451.1 e pela aplicação especí ca do NCAP que simula o monitoramento de pressão e temperatura em poços de petróleo com o objetivo de detectar vazamento. O módulo proposto é embarcado em uma FPGA e para a sua prototipação é usada a placa DE2 da Altera que contém a FPGA Cyclone II EP2C35F672C6. O processador embarcado NIOS II é utilizado para dar suporte à infra-estrutura de software do NCAP que é desenvolvido na linguagem C e se baseia no padrão IEEE 1451.1. A descrição do comportamento da infra-estrutura de hardware é feita utilizando a linguagem VHDL

Arquitetura multiprocessada e reconfigurável para a síntese de redes de Petri em hardware

Uma arquitetura reconfigurável e multiprocessada para a implementação física de Redes de Petri foi desenvolvida em VHDL e mapeada sobre um FPGA. Convencionalmente, as Redes de Petri são transformadas em uma linguagem de descrição de hardware no nível de transferências entre registradores e um processo de síntese de alto nível é utilizado para gerar as funções booleanas e tabelas de transição de estado para que se possa, finalmente, mapeá-las num FPGA (Morris et al., 2000) (Soto and Pereira, 2001). A arquitetura proposta possui blocos lógicos reconfiguráveis desenvolvidos exclusivamente para a implementação dos lugares e das transições da rede, não sendo necessária a descrição da rede em níveis de abstração intermediários e nem a utilização de um processo de síntese para realizar o mapeamento da rede na arquitetura. A arquitetura permite o mapeamento de modelos de Redes de Petri com diferenciação entre as marcas e associação de tempo no disparo das transições, sendo composta por um arranjo de processadores reconfiguráveis, cada um dos quais representando o comportamento de uma transição da Rede de Petri a ser mapeada e por um sistema de comunicação, implementado por um conjunto de roteadores que são capazes de enviar pacotes de dados de um processador reconfigurável a outro. A arquitetura proposta foi validada num FPGA de 10.570 elementos lógicos com uma topologia que permitiu a implementação de Redes de Petri de até 9 transições e 36 lugares, atingindo uma latência de 15,4ns e uma vazão de até 17,12GB/s com uma freqüência de operação de 64,58MHz.

IEEE 1451-based multi-interface module (I2M) for industrial processes automation

This paper describes the implementation of a multi-interface module (I2M) for automation of industrial processes, based on the IEEE1451 standard. Process automation with I2M can communicate through either wires or using wireless communication, without any hardware or software changes. We used FPGA resources to implement the I2M functions FPGA, with a NIOS II processor and ZigBee communication system (IEEE802.15), as well as RS232 serial standard. Part of the project was done in the SOPC Builder environment, which gave the designer flexibility and speed to implement the NIOS II-based microprocessor system. To test the I2M implementation, a didactic Industrial Hydraulic Module (MHI-01) was used to simulate two industrial processes to be controlled by the system proposed.

Common architecture for discrete wavelet transform analysis and synthesis with sequential and constant processing elements

This paper adresses the problem on processing biological data such as cardiac beats, audio and ultrasonic range, calculating wavelet coefficients in real time, with processor clock running at frequency of present ASIC's and FPGA. The Paralell Filter Architecture for DWT has been improved, calculating wavelet coefficients in real time with hardware reduced to 60%. The new architecture, which also processes IDWT, is implemented with the Radix-2 or the Booth-Wallace Constant multipliers. Including series memory register banks, one integrated circuit Signal Analyzer, ultrasonic range, is presented.

Conception of wheeled mobile robots with reconfigurable control using integrate prototyping

With the fast innovation of the hardware and software technologies using rapid prototyping devices, with application in the robotics and automation, more and more it becomes necessary the development of applications based on methodologies that facilitate future modifications, updates and enhancements in the original projected system. This paper presents a conception of mobile robots using rapid prototyping, distributing the several control actions in growing levels of complexity and using resources of reconfigurable computing proposal oriented to embed systems implementation. Software and the hardware are structuralized in independents blocks, with connection through common bus. The study and applications of new structures control that permits good performance in relation to the parameter variations. This kind of controller can be tested on different platform representing the wheeled mobile robots using reprogrammable logic components (FPGA). © 2006 IEEE.

Discrete wavelet transform signal analyzer

This paper addresses the problem of processing biological data, such as cardiac beats in the audio and ultrasonic range, and on calculating wavelet coefficients in real time, with the processor clock running at a frequency of present application-specified integrated circuits and field programmable gate array. The parallel filter architecture for discrete wavelet transform (DWT) has been improved, calculating the wavelet coefficients in real time with hardware reduced up to 60%. The new architecture, which also processes inverse DWT, is implemented with the Radix-2 or the Booth-Wallace constant multipliers. One integrated circuit signal analyzer in the ultrasonic range, including series memory register banks, is presented. © 2007 IEEE.

Implementation of filters for image pre-processing for leaf analyses in plantations

In this work an image pre-processing module has been developed to extract quantitative information from plantation images with various degrees of infestation. Four filters comprise this module: the first one acts on smoothness of the image, the second one removes image background enhancing plants leaves, the third filter removes isolated dots not removed by the previous filter, and the fourth one is used to highlight leaves' edges. At first the filters were tested with MATLAB, for a quick visual feedback of the filters' behavior. Then the filters were implemented in the C programming language. At last, the module as been coded in VHDL for the implementation on a Stratix II family FPGA. Tests were run and the results are shown in this paper. © 2008 Springer-Verlag Berlin Heidelberg.

A true programmable HPF hybrid three-phase rectifier

In this paper is proposed and analyzed a digital hysteresis modulation using a FPGA (Field Programmable Gate Array) device and VHDL (Hardware Description Language), applied at a hybrid three-phase rectifier with almost unitary input power factor, composed by parallel SEPIC controlled single-phase rectifiers connected to each leg of a standard 6-pulses uncontrolled diode rectifier. The digital control allows a programmable THD (Total Harmonic Distortion) at the input currents, and it makes possible that the power rating of the switching-mode converters, connected in parallel, can be a small fraction of the total average output power, in order to obtain a compact converter, reduced input current THD and almost unitary input power factor. The proposed digital control, using a FPGA device and VHDL, offers an important flexibility for the associated control technique, in order to obtain a programmable PFC (Power Factor Correction) hybrid three-phase rectifier, in agreement with the international standards (IEC, and IEEE), which impose limits for the THD of the AC (Alternate Current) line input currents. Finally, the proposed control strategy is verified through experimental results from an implemented prototype. ©2008 IEEE.

HPF boost interleaved operating in discontinuous conduction mode for trolleybus application

This paper deals with results of a research and development (R&D) project in cooperation with Electric Power Distribution Company in São Paulo (Brazil) regarding the development and experimental analysis of a new concept of power drive system suitable for application in traction systems of electrical vehicles pulled by electrical motors, which can be powered by urban DC or AC distribution networks. The proposed front-end structure is composed by five boost power cells in interleaving connection, operating in discontinuous conduction mode as AC-DC converter, or as DC-DC converter, in order to provide the proper DC output voltage range required by DC or AC adjustable speed drivers. Therefore, when supplied by single-phase AC distribution networks, and operating as AC-DC converter, it is capable to provide high power factor, reduced harmonic distortion in the input current, complying with the restrictions imposed by the IEC 61000-3-4 standards resulting in significant improvements for the trolleybuses systems efficiency and for the urban distribution network costs. Considering the compliance with input current restrictions imposed by IEC 61000-3-4 standards, two digital control strategies were evaluated. The digital controller has been implemented using a low cost FPGA (XC3S200) and developed totally using a hardware description language VHDL and fixed point arithmetic. Experimental results from a 15 kW low power scale prototype operating in DC and AC conditions are presented, in order to verify the feasibility and performance of the proposed system. © 2009 IEEE.