Investigations of the scaling criteria for a mild combustion burner

In this paper, a new strategy for scaling burners based on "mild combustion" is evolved and adopted to scaling a burner from 3 to a 150 kW burner at a high heat release Late of 5 MW/m(3) Existing scaling methods (constant velocity, constant residence time, and Cole's procedure [Proc. Combust. Inst. 28 (2000) 1297]) are found to be inadequate for mild combustion burners. Constant velocity approach leads to reduced heat release rates at large sizes and constant residence time approach in unacceptable levels of pressure drop across the system. To achieve mild combustion at high heat release rates at all scales, a modified approach with high recirculation is adopted in the present studies. Major geometrical dimensions are scaled as D similar to Q(1/3) with an air injection velocity of similar to 100 m/s (Delta p similar to 600 mm water gauge). Using CFD support, the position of air injection holes is selected to enhance the recirculation rates. The precise role of secondary air is to increase the recirculation rates and burn LIP the residual CO in the downstream. Measurements of temperature and oxidizer concentrations inside 3 kW, 150 kW burner and a jet flame are used to distinguish the combustion process in these burners. The burner can be used for a wide range of fuels from LPG to producer gas as extremes. Up to 8 dB of noise level reduction is observed in comparison to the conventional combustion mode. Exhaust NO emissions below 26 and 3 ppm and temperatures 1710 and 1520 K were measured for LPG and producer gas when the burner is operated at stoichiometry. (c) 2004 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Service firms´ action upon negative incidents in high touch services: A narrative study

The study concerns service management, and specifically the action service firms take with regard to customer dissatisfaction, customer complaints and complaining customers in high touch services. Customer dissatisfaction, customer complaints and complaining customers are called negative incidents in the study. The study fills a research gap in service management studies by investigating negative incidents as a part of an open service system. In contrast to main stream service management studies defining service quality as how the customer as a consumer defines it, in the present study, the concept of interactive service quality is adopted. The customer is considered as a co-producer of service who thus has a role to play in service quality and productivity. Additionally, the study juxtaposes the often opposed perspectives of the manager and the customer as well as the often forgotten silent voices of service employees and supervisors. The study proposes that the service firm as an entity does not act but it is the actors at the different hierarchical layers who act. Additionally, it is acknowledged in the study that the different actors at the different hierarchical layers have different knowledge of the service system and different objectives for service encounters. Therefore, they interpret the negative incidents from different perspectives and their actions upon negative incidents are subsequently guided by their interpretations. The research question is: how do service firms act upon negative incidents in high touch services? In order to answer to the research question a narrative research approach was chosen. The actors at the different hierarchical layers acted as informants of the study and provided stories about customer dissatisfaction, customer complaining and complaint handling in high touch services. Through storytelling, access to the socially constructed reality of service firms’ action was achieved. Stemming from the literature review, analysis of empirical data and my theoretical thinking, a theory about service firms’ action upon negative incidents in high touch services was developed and the research question was answered. The study contributes to service recovery and complaint management studies as well as to studies on customer orientation and its implementation in service firms. Additionally, the study has a methodological contribution to service management studies since it reflects service firms’ action with narratives from multiple perspectives. The study is positioned in the tradition of the Nordic School of Marketing Thought and presents service firms’ action upon negative incidents in high touch services as a complex human-centered phenomenon in which the actors at the different hierarchical layers have crucial roles to play. Ritva Höykinpuro is associated with CERS, the Centre for Relationship Marketing and Service Management at Hanken School of Economics.

Power and Distribution Network Structure in the People's Republic of China - The Case of an Inland City in Transition

The aim of the current study is to examine the influence of the channel external environment on power, and the effect of power on the distribution network structure within the People’s Republic of China. Throughout the study a dual research process was applied. The theory was constructed by elaborating the main theoretical premises of the study, the channel power theories, the political economy framework and the distribution network structure, but these marketing channel concepts were expanded with other perspectives from other disciplines. The main method applied was a survey conducted among 164 Chinese retailers, complemented by interviews, photographs, observations and census data from the field. This multi-method approach enabled not only to validate and triangulate the quantitative results, but to uncover serendipitous findings as well. The theoretical contribution of the current study to the theory of marketing channels power is the different view it takes on power. First, earlier power studies have taken the producer perspective, whereas the current study also includes a distributor perspective to the discussion. Second, many power studies have dealt with strongly dependent relationships, whereas the current study examines loosely dependent relationships. Power is dependent on unequal distribution of resources rather than based on high dependency. The benefit of this view is in realising that power resources and power strategies are separate concepts. The empirical material of the current study confirmed that at least some resources were significantly related to power strategies. The study showed that the dimension resources composed of technology, know-how and knowledge, managerial freedom and reputation was significantly related to non-coercive power. Third, the notion of different outcomes of power is a contribution of this study to the channels power theory even though not confirmed by the empirical results. Fourth, it was proposed that channel external environment other than the resources would also contribute to the channel power. These propositions were partially supported thus providing only partial contribution to the channel power theory. Finally, power was equally distributed among the different types of actors. The findings from the qualitative data suggest that different types of retailers can be classified according to the meaning the actors put into their business. Some are more business oriented, for others retailing is the only way to earn a living. The findings also suggest that in some actors both retailing and wholesaling functions emerge, and this has implications for the marketing channels structure.

Exploring Customer Value Formation: A Customer Dominant Logic Perspective

This paper extends current discussions about value creation and proposes a customer dominant value perspective. A customer-dominant marketing logic positions the customer in the center, rather than the service provider/producer or the interaction or the system. The focus is shifted from the company´s service processes involving the customer, to the customer´s multi-contextual value formation, involving the company. It is argued that value is not always an active process of creation; instead value is embedded and formed in the highly dynamic and multi-contextual reality and life of the customer. This leads to a need to look beyond the current line of visibility where visible customer-company interactions are focused to the invisible and mental life of the customer. From this follows a need to extend the temporal scope, from exchange and use even further to accumulated experiences in the customer´s life. The aim of this paper is to explore value formation from a customer dominant logic perspective. This is done in three steps: first, value formation is contrasted to earlier views on the company’s role in value creation by using a broad ontologically driven framework discussing what, how, when, where and who. Next, implications of the proposed characteristics of value formation compared to earlier approaches are put forward. Finally, some tentative suggestions of how this perspective would affect marketing in service companies are presented. As value formation in a CDL perspective has a different focus and scope than earlier views on value it leads to posing questions about the customer that reveals earlier hidden aspects of the role of a service for the customer. This insight might be used in service development and innovation.

Bacteria colonizing paper machines

Bacteria growing in paper machines can cause several problems. Biofilms detaching from paper machine surfaces may lead to holes and spots in the end product or even break the paper web leading to expensive delays in production. Heat stable endospores will remain viable through the drying section of paper machine, increasing the microbial contamination of paper and board. Of the bacterial species regularly found in the end products, Bacillus cereus is the only one classified as a pathogen. Certain B. cereus strains produce cereulide, the toxin that causes vomiting disease in food poisonings connected to B. cereus. The first aim of this thesis was to identify harmful bacterial species colonizing paper machines and to assess the role of bacteria in the formation of end product defects. We developed quantitative PCR methods for detecting Meiothermus spp. and Pseudoxanthomonas taiwanensis. Using these methods I showed that Meiothermus spp. and Psx. taiwanensis are major biofoulers in paper machines. I was the first to be able to show the connection between end product defects and biofilms in the wet-end of paper machines. I isolated 48 strains of primary-biofilm forming bacteria from paper machines. Based on one of them, strain K4.1T, I described a novel bacterial genus Deinobacterium with Deinobacterium chartae as the type species. I measured the transfer of Bacillus cereus spores from packaging paper into food. To do this, we constructed a green fluorescent protein (GFP) labelled derivative of Bacillus thuringiensis and prepared paper containing spores of this strain. Chocolate and rice were the recipient foods when transfer of the labelled spores from the packaging paper to food was examined. I showed that only minority of the Bacillus cereus spores transferred into food from packaging paper and that this amount is very low compared to the amount of B. cereus naturally occurring in foods. Thus the microbiological risk caused by packaging papers is very low. Until now, the biological function of cereulide for the producer cell has remained unknown. I showed that B. cereus can use cereulide to take up K+ from environment where K+ is scarce: cereulide binds K+ ions outside the cell with high affinity and transports these ions across cell membrane into the cytoplasm. Externally added cereulide increased the growth rate of cereulide producing strains in medium where potassium was growth limiting. In addition, cereulide producing strains outcompeted cereulide non-producing B. cereus in potassium deficient environment, but not when the potassium concentration was high. I also showed that cereulide enhances biofilm formation of B. cereus.

Asukkaan Helsinki? : Tapaustutkimus vuorovaikutteisuudesta kaupunkisuunnittelussa

This study examines the interaction between inhabitants and urban planning. In addition to traditional methods of participation there can be seen an increasing need to find new channels and means to influence on one´s environment. Hearing of inhabitants during planning is hoped to decrease the amount of claims and this way to speed up the planning process. Discussion that emphasizes competitiveness and innovativeness in planning has brought out the role of inhabitants as selective consumers and end users. This extension of civil perspective completes the thought of participation in city planning and adds the pressure on developing the interaction and user orientation. The aim of the study is to point out the present situation of inhabitant´s participation and influencing in Helsinki. Helsinki City Planning Department opened a new information and exhibiotion hall called Laituri in 2008. Laituri provides the latest information about planning projects in Helsinki and temporary exhibitions as well as it operates as communication channel and information point for the department. In this study Laituri is examined as a case study of interaction between citizen and planner. The study is divided into two principal themes. The aim is to research action and interactivity at Laituri from the inhabitants´and planners´point of view. The qualitative study has inquiries, interview surveys and observation as research methods. Empiricial data of the study consists of three parts which complement each other: Laituri operational reseach, inquiry directed to the members of Laituri team and interviews of three experts. The aim is to find answers to questions like, does Laituri reach the citizens and will the opportunities to participate improve along Laituri. The study examines also how the local knowledge of inhabitants will come across to planners and further to planning. The study combines discussions of inhabitants´ influencing in Finnish society and science community. Cornerstones of the study are inhabitant participation, interaction and local knowledge in urban planning. The theory behind the study is communicative planning theory. In addition the theory consists of key concepts. The study introduces a concept of Inhabitant´s Helsinki, which reflects the inhabitant as customer-citizen who is an active product developer in participative urban planning. According to the research results the experts of Laituri and majority of inhabitants in Helsinki experience that the inhabitant´s possibilities to participate will improve along Laituri. However half of the citizens in Helsinki believe that local knowledge and ideas will only have minor impact on the final plan. According to city dwellers the present practise used by Helsinki City Planning Department supports only partially adequate interaction. The experts of Laituri experience that the role of Laituri is first of all forum of communication and discussion channel instead of effective local data collector. Based on the results the study introduces a model of inhabitant´s participation field. According to the model Laituri can be seen as phenomenom in Helsinki urban planning which has the elements of network municipality. The planner is more like diplomatic trend-setter and visionary. The inhabitant of Helsinki is an expert in city living and participative producer of local knowledge. Participation methods are increasingly segmented and tailored in every plan and project. The study argues that Inhabitant´s Helsinki is a pluralistic milieu in constant pressure for change. Therefore reaching the everyday life experiencies of inhabintants should be at higher degree in Helsinki City Planning Department´s operations.

Renewable Energy and Climate Policies: Studies in the Forest and Energy Sector

‪This dissertation examines the impacts of energy and climate policies on the energy and forest sectors, focusing on the case of Finland. The thesis consists of an introduction article and four separate studies. The dissertation was motivated by the climate concern and the increasing demand of renewable energy. In particular, the renewable energy consumption and greenhouse gas emission reduction targets of the European Union were driving this work. In Finland, both forest and energy sectors are in key roles in achieving these targets. In fact, the separation between forest and energy sector is diminishing as the energy sector is utilizing increasing amounts of wood in energy production and as the forest sector is becoming more and more important energy producer.‬ ‪The objective of this dissertation is to find out and measure the impacts of climate and energy policies on the forest and energy sectors. In climate policy, the focus is on emissions trading, and in energy policy the dissertation focuses on the promotion of renewable forest-based energy use. The dissertation relies on empirical numerical models that are based on microeconomic theory. Numerical partial equilibrium mixed complementarity problem models were constructed to study the markets under scrutiny. The separate studies focus on co-firing of wood biomass and fossil fuels, liquid biofuel production in the pulp and paper industry, and the impacts of climate policy on the pulp and paper sector.‬ ‪The dissertation shows that the policies promoting wood-based energy may have have unexpected negative impacts. When feed-in tariff is imposed together with emissions trading, in some plants the production of renewable electricity might decrease as the emissions price increases. The dissertation also shows that in liquid biofuel production, investment subsidy may cause high direct policy costs and other negative impacts when compared to other policy instruments. The results of the dissertation also indicate that from the climate mitigation perspective, perfect competition is the favored wood market competition structure, at least if the emissions trading system is not global.‬ ‪In conclusion, this dissertation suggests that when promoting the use of wood biomass in energy production, the favored policy instruments are subsidies that promote directly the renewable energy production (i.e. production subsidy, renewables subsidy or feed-in premium). Also, the policy instrument should be designed to be dependent on the emissions price or on the substitute price. In addition, this dissertation shows that when planning policies to promote wood-based renewable energy, the goals of the policy scheme should be clear before decisions are made on the choice of the policy instruments.‬

Production of biosurfactant “Biosur-Pm” by Pseudomonas maltophila CSV89: characterization and role in hydrocarbon uptake

Pseudomonas maltophilia CSV89, a soil bacterium, produces an extracellular biosurfactant, ''Biosur-Pm''. The partially purified product is nondialyzable and chemically composed of 50% protein and 12-15% sugar, which indicates the complex nature of Biosur-Pm. It reduces the surface tension of water from 73 to 53 x 10(-3) N m(-1) and has a critical micellar concentration of 80 mg/l. Compared to aliphatic hydrocarbons, Biosur-Pm shows good activity against aromatic hydrocarbons. The emulsion formed is stable and does not require any metal ions for emulsification. The kinetics of Biosur-Pm production suggest that its synthesis isa growth-associated and pH-dependent process. At pH 7.0, cells produced more Biosur-Pm with less cell surface hydrophobicity. At pH 8.0, however, the cells produced less Biosur-Pm with more cell surface hydrophobicity and showed a twofold higher affinity for aromatic hydrocarbons compared to the cells grown at pH 7.0. The Biosur-Pm showed a pH-dependent release, stimulated growth of the producer strain on mineral salts medium with 1-naphthoic acid when added externally, and facilitated the conversion of salicylate to catechol. All these results suggest that Biosur-Pm is probably a cell-wall component and helps in hydrocarbon assimilation/uptake.

Operational experience on a grid connected 100 kWe biomass gasification power plant in Karnataka, India

The paper reports the operational experience from a 100 kWe gasification power plant connected to the grid in Karnataka. Biomass Energy for Rural India (BERI) is a program that implemented gasification based power generation with an installed capacity of 0.88 MWe distributed over three locations to meet the electrical energy needs in the district of Tumkur. The operation of one 100 kWe power plant was found unsatisfactory and not meeting the designed performance. The Indian Institute of Science, Bangalore, the technology developer, took the initiative to ensure the system operation, capacity building and prove the designed performance. The power plant connected to the grid consists of the IISc gasification system which includes reactor, cooling, cleaning system, fuel drier and water treatment system to meet the producer gas quality for an engine. The producer gas is used as a fuel in Cummins India Limited, GTA 855 G model, turbo charged engine and the power output is connected to the grid. The system has operated for over 1000 continuous hours, with only about 70 h of grid outages. The total biomass consumption for 1035 h of operation was 111 t at an average of 107 kg/h. Total energy generated was 80.6 MWh reducing over loot of CO(2) emissions. The overall specific fuel consumption was about 1.36 kg/kWh, amounting to an overall efficiency from biomass to electricity of about 18%. The present operations indicate that a maintenance schedule for the plant can be at the end of 1000 h. The results for another 1000 h of operation by the local team are also presented. (C) 2011 International Energy Initiative. Published by Elsevier Inc. All rights reserved.

Hybrid Bayesian Classifier for Improved Classification Accuracy

The widely used Bayesian classifier is based on the assumption of equal prior probabilities for all the classes. However, inclusion of equal prior probabilities may not guarantee high classification accuracy for the individual classes. Here, we propose a novel technique-Hybrid Bayesian Classifier (HBC)-where the class prior probabilities are determined by unmixing a supplemental low spatial-high spectral resolution multispectral (MS) data that are assigned to every pixel in a high spatial-low spectral resolution MS data in Bayesian classification. This is demonstrated with two separate experiments-first, class abundances are estimated per pixel by unmixing Moderate Resolution Imaging Spectroradiometer data to be used as prior probabilities, while posterior probabilities are determined from the training data obtained from ground. These have been used for classifying the Indian Remote Sensing Satellite LISS-III MS data through Bayesian classifier. In the second experiment, abundances obtained by unmixing Landsat Enhanced Thematic Mapper Plus are used as priors, and posterior probabilities are determined from the ground data to classify IKONOS MS images through Bayesian classifier. The results indicated that HBC systematically exploited the information from two image sources, improving the overall accuracy of LISS-III MS classification by 6% and IKONOS MS classification by 9%. Inclusion of prior probabilities increased the average producer's and user's accuracies by 5.5% and 6.5% in case of LISS-III MS with six classes and 12.5% and 5.4% in IKONOS MS for five classes considered.

Tar characterisation in new generation agro-residue gasifiers - Cyclone and downdraft open top twin air entry systems

This paper deals with the characterisation of tar from two configurations of bioresidue thermochemical conversion reactors designed for producer gas based power generation systems. The pulverised fuel reactor is a cyclone system (R1) and the solid bioresidue reactor (denoted R2) is an open top twin air entry system both at 75-90 kg/h capacity (to generate electricity similar to 100 kVA). The reactor, R2, has undergone rigorous test in a major Indo-Swiss programme for the tar quantity at various conditions. The former is a recent technology development. Tars collected from these systems by a standard tar collection apparatus at the laboratory at Indian Institute of Science have been analysed at the Royal Institute of Technology (KTH), Sweden. The results of these analyses show that these thermochemical conversion reactors behave differently from the earlier reactors reported in literature in so far as tar generation is concerned. The extent of tar in hot gas is about 700-800 ppm for R1 and 70-100 ppm for R2. The amounts of the major compounds - naphthalene and phenol-are much lower that what is generally understood to happen in the gasifiers in Europe. It is suggested that the longer residence times at high temperatures allowed for in these reactors is responsible for this behavior. It is concluded the new generation reactor concepts extensively tried out at lower power levels hold promise for high power atmospheric gasification systems for woody as well as pulverisable bioresidues.

Static analysis for checking data format compatibility of programs

Large software systems are developed by composing multiple programs. If the programs manip-ulate and exchange complex data, such as network packets or files, it is essential to establish that they follow compatible data formats. Most of the complexity of data formats is associated with the headers. In this paper, we address compatibility of programs operating over headers of network packets, files, images, etc. As format specifications are rarely available, we infer the format associated with headers by a program as a set of guarded layouts. In terms of these formats, we define and check compatibility of (a) producer-consumer programs and (b) different versions of producer (or consumer) programs. A compatible producer-consumer pair is free of type mismatches and logical incompatibilities such as the consumer rejecting valid outputs gen-erated by the producer. A backward compatible producer (resp. consumer) is guaranteed to be compatible with consumers (resp. producers) that were compatible with its older version. With our prototype tool, we identified 5 known bugs and 1 potential bug in (a) sender-receiver modules of Linux network drivers of 3 vendors and (b) different versions of a TIFF image library.

Experiments and analysis of propagation front under gasification regimes in a packed bed

The paper analyses the results of experiments on the propagation rate in a fuel bed under gasification conditions in a co-current reactor configuration. Experiments using wood chips with different values of moisture content have been conducted under gasification conditions. The influence of air mass flux on the propagation rate, peak temperature and gas quality is investigated. It is observed from the experiments that the flame front propagation rate initially increases as the air mass flux increased, reaching a peak propagation rate, and further increase in the air mass flux results in a decrease in the propagation rate. However, the bed movement increases with the increase in air mass flux. The experimental results provide an understanding on influence of the fuel properties on propagation front. The surface area per unit volume of the particles in the packed bed plays an important role in the propagation rate. It has been argued that the flaming pyrolysis contributes towards the flame propagation as opposed to the overall combustion process in a packed bed. The calorific value of the producer gas generated is nearly the same over the entire range of air mass flux for bone-dry and 10% moist wood. (C) 2014 Elsevier B.V. All rights reserved.

The knight of sugar industry: T. S. Venkatraman (1884-1963)

Tiruvadi Sambasiva Venkatraman (TSV) was a plant breeder. In response to a call from Pundit Madan Mohan Malaviya, he made it his mission to develop high-yielding varieties of sugarcane for manufacturing sugar and making it available as a sweetening agent and an energy source for the malnourished children of India. Using Saccharum officinarum, then under cultivation in India, as the female parent, he artificially fertilized it with pollen from S. barberi, which grew wild in Coimbatore. After 4-5 recurrent backcrossings of S. officinarum Chi wild Sorghum spontaneum with S. officinarum as the female parent, TSV selected the `rare' interspecies hybrid cane varieties that resembled sugarcane and had approximately 2.5 cm thick juicy stems containing 16-18% sucrose - nearly 35 times more than what occurred in parent stocks. The hybrid canes matured quickly, were resistant to waterlogging, drought, and to the red-rot disease caused by Glomerella tucumanensis (Sordariomycetes: Glomerellaceae), and to the sereh-virus disease. Most importantly, they were amenable for propagation using stem cuttings. In recognition of the development of high-yielding sugarcane varieties, TSV was conferred the titles Rao Bahadur, Rao Sahib, and Sir by the British Government, and Padma Bhushan by the Republic of India. In the next few decades, consequent to TSV's work, India turned into the second largest sugar producer in the world, after Brazil. The hybrid sugarcane varieties developed are the foundational stocks for new sugarcane x bamboo hybrids, and for possible resistance to Puccinia megalocephala (Pucciniomycetes: Pucciniaceae) and Ustilago scitaminea (Ustilaginomycetes: Ustilaginaceae) using molecular techniques.

In-cylinder investigations and analysis of a SI gas engine fuelled with H-2 and CO rich syngas fuel: Sensitivity analysis of combustion descriptors for engine diagnostics and control

The sensitivity of combustion phasing and combustion descriptors to ignition timing, load and mixture quality on fuelling a multi-cylinder natural gas engine with bio-derived H-2 and CO rich syngas is addressed. While the descriptors for conventional fuels are well established and are in use for closed loop engine control, presence of H-2 in syngas potentially alters the mixture properties and hence combustion phasing, necessitating the current study. The ability of the descriptors to predict abnormal combustion, hitherto missing in the literature, is also addressed. Results from experiments using multi-cylinder engines and numerical studies using zero dimensional Wiebe function based simulation models are reported. For syngas with 20% H-2 and CO and 2% CH4 (producer gas), an ignition retard of 5 +/- 1 degrees was required compared to natural gas ignition timing to achieve peak load of 72.8 kWe. It is found that, for syngas, whose flammability limits are 0.42-1.93, the optimal engine operation was at an equivalence ratio of 1.12. The same methodology is extended to a two cylinder engine towards addressing the influence of syngas composition, especially H-2 fraction (varying from 13% to 37%), on the combustion phasing. The study confirms the utility of pressure trace derived combustion descriptors, except for the pressure trace first derivative, in describing the MBT operating condition of the engine when fuelled with an alternative fuel. Both experiments and analysis suggest most of the combustion descriptors to be independent of the engine load and mixture quality. A near linear relationship with ignition angle is observed. The general trend(s) of the combustion descriptors for syngas fuelled operation are similar to those of conventional fuels; the differences in sensitivity of the descriptors for syngas fuelled engine operation requires re-calibration of control logic for MBT conditions. Copyright (C) 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.