Síntese e caracterização de materiais semicondutores nanoestruturados luminescentes à base de ZnS

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Persistent luminescence mechanisms: human imagination at work

The present status and future progress of the mechanisms of persistent luminescence are critically treated with the present knowledge. The advantages to be achieved by a further need as well as the pitfalls of the excessive use of imagination are shown. As usual, in the beginning of the present era of persistent luminescence since the mid 1990s, the imagination played a more important role than the sparse solid experimental data and the chemical common sense and knowledge was largely ignored. Since some five years, the mechanistic studies seem to have reached the maturity and - perhaps deceivingly - it seems that there are only details to be solved. However, the development of red emitting nanocrystalline materials poses a challenge also to the more fundamental studies and interpretation. The questions still luring in the darkness include the problems how the increased surface area affects the defect structure and how the "persistent energy transfer" really works. There is still some light to be thrown onto these matters starting with agreeing on the terminology: the term phosphorescence should be abandoned altogether. The long lifetime of persistent luminescence is due to trapping of excitation energy, not to the forbidden nature of the luminescent transition. However, the technically well-suited term "afterglow" should be retained for harmful, short persistent luminescence. (C) 2012 Optical Society of America

NIR luminescent Er3+/Yb3+ co-doped SiO2-ZrO2 nanostructured planar and channel waveguides: Optical and structural properties

Optical and structural properties of planar and channel waveguides based on sol gel Er3+ and Yb3+ co-doped SiO2-ZrO2 are reported. Microstructured channels with high homogeneous surface profile were written onto the surface of multilayered densified films deposited on SiO2/Si substrates by a femtosecond laser etching technique. The densification of the planar waveguides was evaluated from changes in the refractive index and thickness, with full densification being achieved at 900 degrees C after annealing from 23 up to 500 min, depending on the ZrO2 content Crystal nucleation and growth took place together with densification, thereby producing transparent glass ceramic planar waveguides containing rare earth-doped ZrO2 nanocrystals dispersed in a silica-based glassy host Low roughness and crack-free surface as well as high confinement coefficient were achieved for all the compositions. Enhanced NIR luminescence of the Er3+ ions was observed for the Yb3+- codoped planar waveguides, denoting an efficient energy transfer from the Yb3+ to the Er3+ ion. (C) 2012 Elsevier B.V. All rights reserved.

Quantum Mechanics Insight into the Microwave Nucleation of SrTiO3 Nanospheres

An extensive investigation of strontium titanate, SrTiO3 (STO), nanospheres synthesized via a microwave-assisted hydrothermal (MAH) method has been conducted to gain a better insight into thermodynamic, kinetic, and reaction phenomena involved in STO nucleation and crystal growth processes. To this end, quantum chemical modeling based on the density functional theory and periodic super cell models were done. Several experimental techniques were employed to get a deep characterization of structural and optical features of STO nanospheres. A possible formation mechanism was proposed, based on dehydration of titanium and strontium clusters followed by mesoscale transformation and a self-assembly process along an oriented attachment mechanism resulting in spherical like shape. Raman and XANES analysis renders a noncentrosymmetric environment for the octahedral titanium, while infrared and first order Raman modes reveal OH groups which are unsystematically incorporated into uncoordinated superficial sites. These results seem to indicate that the key component is the presence of distorted TiO6 clusters to engender a luminescence property. Analysis of band structure, density Of states, and charge map shows that there is a close relationship among local broken symmetry, polarization, and energy split of the 3d orbitals of titanium. The interplay among these electronic and structural features provides necessary conditions to evaluate its luminescent properties under two energy excitation.

Preparation and Structural Characterization of Vulcanized Natural Rubber Nanocomposites Containing Nickel-Zinc Ferrite Nanopowders

Single-phase polycrystalline mixed nickel-zinc ferrites belonging to Ni0.5Zn0.5Fe2O4 were prepared on a nanometric scale (mean crystallite size equal to 14.7 nm) by chemical synthesis named the modified poliol method. Ferrite nanopowder was then incorporated into a natural rubber matrix producing nanocomposites. The samples were investigated by means of infrared spectroscopy, X-ray diffraction, scanning electron microscopy and magnetic measurements. The obtained results suggest that the base concentration of nickel-zinc ferrite nanoparticles inside the polymer matrix volume greatly influences the magnetic properties of nanoconnposites. A small quantity of nanoparticles, less than 10 phr, in the nanocomposite is sufficient to produce a small alteration in the semi-crystallinity of nanocomposites observed by X-ray diffraction analysis and it produces a flexible magnetic composite material with a saturation magnetization, a coercivity field and an initial magnetic permeability equal to 3.08 emu/g, 99.22 Oe and 9.42 X 10(-5) respectively.

Influence of the Sol-Gel pH Process and Compact Film on the Efficiency of TiO2-Based Dye-Sensitized Solar Cells

The influence of pH during hydrolysis of titanium(IV) isopropoxide on the morphological and electronic properties of TiO2 nanoparticles prepared by the sol-gel method is investigated and correlated to the photoelectrochemical parameters of dye-sensitized solar cells (DSCs) based on TiO2 films. Nanoparticles prepared under acid pH exhibit smaller particle size and higher surface area, which result in higher dye loadings and better short-circuit current densities than DSCs based on alkaline TiO2-processed films. On the other hand, the product of charge collection and separation quantum yields in films with TiO2 obtained by alkaline hydrolysis is c. a. 27% higher than for the acid TiO2 films. The combination of acid and alkaline TiO2 nanoparticles as mesoporous layer in DSCs results in a synergic effect with overall efficiencies up to 6.3%, which is better than the results found for devices employing one of the nanoparticles separately. These distinct nanoparticles can be also combined by using the layer-by-layer technique (LbL) to prepare compact TiO2 films applied before the mesoporous layer. DSCs employing photoanodes with 30 TiO2 bilayers have shown efficiencies up to 12% higher than the nontreated photoanode ones. These results can be conveniently used to develop optimized synthetic procedures of TiO2 nanoparticles for several dye-sensitized solar cell applications.

Sviluppo di biosensori: modifiche di superfici elettrodiche e sistemi di immobilizzazione enzimatica

An amperometric glucose biosensor was developed using an anionic clay matrix (LDH) as enzyme support. The enzyme glucose oxidase (GOx) was immobilized on a layered double hydroxide Ni/Al-NO3 LDH during the electrosynthesis, which was followed by crosslinking with glutaraldehyde (GA) vapours or with GA and bovine serum albumin (GABSA) to avoid the enzyme release. The electrochemical reaction was carried out potentiostatically, at -0.9V vs. SCE, using a rotating disc Pt electrode to assure homogeneity of the electrodeposition suspension, containing GOx, Ni(NO3)2 and Al(NO3)3 in 0.3 M KNO3. The mechanism responsible of the LDH electrodeposition involves the precipitation of the LDH due to the increase of pH at the surface of the electrode, following the cathodic reduction of nitrates. The Pt surface modified with the Ni/Al-NO3 LDH shows a much reduced noise, giving rise to a better signal to noise ratio for the currents relative to H2O2 oxidation, and a linear range for H2O2 determination wider than the one observed for bare Pt electrodes. We pointed out the performances of the biosensor in terms of sensitivity to glucose, calculated from the slope of the linear part of the calibration curve for enzimatically produced H2O2; the sensitivity was dependent on parameters related to the electrodeposition in addition to working conditions. In order to optimise the glucose biosensor performances, with a reduced number of experimental runs, we applied an experimental design. A first screening was performed considering the following variables: deposition time (30 - 120 s), enzyme concentration (0.5 - 3.0 mg/mL), Ni/Al molar ratio (3:1 or 2:1) of the electrodeposition solution at a total metals concentration of 0.03 M and pH of the working buffer solution (5.5-7.0). On the basis of the results from this screening, a full factorial design was carried out, taking into account only enzyme concentration and Ni/Al molar ratio of the electrosynthesis solution. A full factorial design was performed to study linear interactions between factors and their quadratic effects and the optimal setup was evaluated by the isoresponse curves. The significant factors were: enzyme concentration (linear and quadratic terms) and the interaction between enzyme concentration and Ni/Al molar ratio. Since the major obstacle for application of amperometric glucose biosensors is the interference signal resulting from other electro-oxidizable species present in the real matrices, such as ascorbate (AA), the use of different permselective membranes on Pt-LDHGOx modified electrode was discussed with the aim of improving biosensor selectivity and stability. Conventional membranes obtained using Nafion, glutaraldehyde (GA) vapours, GA-BSA were tested together with more innovative materials like palladium hexacyanoferrate (PdHCF) and titania hydrogels. Particular attention has been devoted to hydrogels, because they possess some attractive features, which are generally considered to favour biosensor materials biocompatibility and, consequently, the functional enzyme stability. The Pt-LDH-GOx-PdHCF hydrogel biosensor presented an anti-interferant ability so that to be applied for an accurate glucose analysis in blood. To further improve the biosensor selectivity, protective membranes containing horseradish peroxidase (HRP) were also investigated with the aim of oxidising the interferants before they reach the electrode surface. In such a case glucose determination was also accomplished in real matrices with high AA content. Furthermore, the application of a LDH containing nickel in the oxidised state was performed not only as a support for the enzyme, but also as anti-interferant sistem. The result is very promising and it could be the starting point for further applications in the field of amperometric biosensors; the study could be extended to other oxidase enzymes.

Materiali Ceramici per Edilizia con Funzionalità Fotocatalitica

This thesis wad aimed at the study and application of titanium dioxide photocatalytic activity on ceramic materials. As a matter of fact, photocatalysis is a very promising method to face most of the problems connected with the increasing environmental pollution. Furthermore, titanium dioxide, in its anatase crystallographic phase, is one of the most investigated photocatalytic material and results to be perfectly compatible with silicate body mixes. That goal was pursued by two different strategies: 1. the addition to a body mix used for heavy clay products of several titania powders, with different mean crystallite size, surface area, morphology and anatase/rutile ratio and a titania nanosuspension as well. The titania addition followed two procedures: bulk and spray addition over the ceramic samples surface. Titania was added in two different percentages: 2.5 and 7.5 wt.% in both of the methods. The ceramic samples were then fired at three maximum temperatures: 900, 950 and 1000 °C. Afterwards, the photocatalytic activity of the prepared ceramic samples was evaluated by following the degradation of an organic compound in aqueous medium, under UV radiation. The influence of titania morphological characteristics on the photoactivity of the fired materials was studied by means of XRD and SEM observations. The ceramic samples, sprayed with a slip containing 7.5 wt.% of titania powder and fired at 900 °C, have the best photoactivity, with a complete photo-decomposition of the organic compound. At 1000 °C no sample acted as a photocatalyst due to the anatase-to-rutile phase transformation and to the reaction between titania and calcium and iron oxides in the raw materials. 2. The second one foresaw the synthesis of TiO2-SiO2 solid solutions, using the following stoichiometry: Ti1-xSixO2 where x = 0, 0.1, 0.3 and 0.5 atoms per formula unit (apfu). The mixtures were then fired following two thermal cycles, each with three maximum temperatures. The effect of SiO2 addition into the TiO2 crystal structure and, consequently, on its photocatalytic activity when fired at high temperature, was thoroughly investigated by means of XRD, XPS, FE-SEM, TEM and BET analysis. The photoactivity of the prepared powders was assessed both in gas and liquid phase. Subsequently, the TiO2-SiO2 solid solutions, previously fired at 900 °C, were sprayed over the ceramic samples surface in the percentage of 7.5 wt.%. The prepared ceramic samples were fired at 900 and 1000 °C. The photocatalytic activity of the ceramic samples was evaluated in liquid phase. Unfortunately, that samples did not show any appreciable photoactivity. In fact, samples fired at 900 °C showed a pretty low photoactivity, while the one fired at 1000 °C showed no photoactivity at all. This was explained by the excessive coarsening of titania particles. To summarise, titania particle size, more than its crystalline phase, seems to have a relevant role in the photocatalytic activity of the ceramic samples.

Structural changes and dynamic behaviour of vanadium oxide-based catalysts for gas-phase selective oxidations

Selective oxidation is one of the simplest functionalization methods and essentially all monomers used in manufacturing artificial fibers and plastics are obtained by catalytic oxidation processes. Formally, oxidation is considered as an increase in the oxidation number of the carbon atoms, then reactions such as dehydrogenation, ammoxidation, cyclization or chlorination are all oxidation reactions. In this field, most of processes for the synthesis of important chemicals used vanadium oxide-based catalysts. These catalytic systems are used either in the form of multicomponent mixed oxides and oxysalts, e.g., in the oxidation of n-butane (V/P/O) and of benzene (supported V/Mo/O) to maleic anhydride, or in the form of supported metal oxide, e.g., in the manufacture of phthalic anhydride by o-xylene oxidation, of sulphuric acid by oxidation of SO2, in the reduction of NOx with ammonia and in the ammoxidation of alkyl aromatics. In addition, supported vanadia catalysts have also been investigated for the oxidative dehydrogenation of alkanes to olefins , oxidation of pentane to maleic anhydride and the selective oxidation of methanol to formaldehyde or methyl formate [1]. During my PhD I focused my work on two gas phase selective oxidation reactions. The work was done at the Department of Industrial Chemistry and Materials (University of Bologna) in collaboration with Polynt SpA. Polynt is a leader company in the development, production and marketing of catalysts for gas-phase oxidation. In particular, I studied the catalytic system for n-butane oxidation to maleic anhydride (fluid bed technology) and for o-xylene oxidation to phthalic anhydride. Both reactions are catalyzed by systems based on vanadium, but catalysts are completely different. Part A is dedicated to the study of V/P/O catalyst for n-butane selective oxidation, while in the Part B the results of an investigation on TiO2-supported V2O5, catalyst for o-xylene oxidation are showed. In Part A, a general introduction about the importance of maleic anhydride, its uses, the industrial processes and the catalytic system are reported. The reaction is the only industrial direct oxidation of paraffins to a chemical intermediate. It is produced by n-butane oxidation either using fixed bed and fluid bed technology; in both cases the catalyst is the vanadyl pyrophosphate (VPP). Notwithstanding the good performances, the yield value didn’t exceed 60% and the system is continuously studied to improve activity and selectivity. The main open problem is the understanding of the real active phase working under reaction conditions. Several articles deal with the role of different crystalline and/or amorphous vanadium/phosphorous (VPO) compounds. In all cases, bulk VPP is assumed to constitute the core of the active phase, while two different hypotheses have been formulated concerning the catalytic surface. In one case the development of surface amorphous layers that play a direct role in the reaction is described, in the second case specific planes of crystalline VPP are assumed to contribute to the reaction pattern, and the redox process occurs reversibly between VPP and VOPO4. Both hypotheses are supported also by in-situ characterization techniques, but the experiments were performed with different catalysts and probably under slightly different working conditions. Due to complexity of the system, these differences could be the cause of the contradictions present in literature. Supposing that a key role could be played by P/V ratio, I prepared, characterized and tested two samples with different P/V ratio. Transformation occurring on catalytic surfaces under different conditions of temperature and gas-phase composition were studied by means of in-situ Raman spectroscopy, trying to investigate the changes that VPP undergoes during reaction. The goal is to understand which kind of compound constituting the catalyst surface is the most active and selective for butane oxidation reaction, and also which features the catalyst should possess to ensure the development of this surface (e.g. catalyst composition). On the basis of results from this study, it could be possible to project a new catalyst more active and selective with respect to the present ones. In fact, the second topic investigated is the possibility to reproduce the surface active layer of VPP onto a support. In general, supportation is a way to improve mechanical features of the catalysts and to overcome problems such as possible development of local hot spot temperatures, which could cause a decrease of selectivity at high conversion, and high costs of catalyst. In literature it is possible to find different works dealing with the development of supported catalysts, but in general intrinsic characteristics of VPP are worsened due to the chemical interaction between active phase and support. Moreover all these works deal with the supportation of VPP; on the contrary, my work is an attempt to build-up a V/P/O active layer on the surface of a zirconia support by thermal treatment of a precursor obtained by impregnation of a V5+ salt and of H3PO4. In-situ Raman analysis during the thermal treatment, as well as reactivity tests are used to investigate the parameters that may influence the generation of the active phase. Part B is devoted to the study of o-xylene oxidation of phthalic anhydride; industrially, the reaction is carried out in gas-phase using as catalysts a supported system formed by V2O5 on TiO2. The V/Ti/O system is quite complex; different vanadium species could be present on the titania surface, as a function of the vanadium content and of the titania surface area: (i) V species which is chemically bound to the support via oxo bridges (isolated V in octahedral or tetrahedral coordination, depending on the hydration degree), (ii) a polymeric species spread over titania, and (iii) bulk vanadium oxide, either amorphous or crystalline. The different species could have different catalytic properties therefore changing the relative amount of V species can be a way to optimize the catalytic performances of the system. For this reason, samples containing increasing amount of vanadium were prepared and tested in the oxidation of o-xylene, with the aim of find a correlations between V/Ti/O catalytic activity and the amount of the different vanadium species. The second part deals with the role of a gas-phase promoter. Catalytic surface can change under working conditions; the high temperatures and a different gas-phase composition could have an effect also on the formation of different V species. Furthermore, in the industrial practice, the vanadium oxide-based catalysts need the addition of gas-phase promoters in the feed stream, that although do not have a direct role in the reaction stoichiometry, when present leads to considerable improvement of catalytic performance. Starting point of my investigation is the possibility that steam, a component always present in oxidation reactions environment, could cause changes in the nature of catalytic surface under reaction conditions. For this reason, the dynamic phenomena occurring at the surface of a 7wt% V2O5 on TiO2 catalyst in the presence of steam is investigated by means of Raman spectroscopy. Moreover a correlation between the amount of the different vanadium species and catalytic performances have been searched. Finally, the role of dopants has been studied. The industrial V/Ti/O system contains several dopants; the nature and the relative amount of promoters may vary depending on catalyst supplier and on the technology employed for the process, either a single-bed or a multi-layer catalytic fixed-bed. Promoters have a quite remarkable effect on both activity and selectivity to phthalic anhydride. Their role is crucial, and the proper control of the relative amount of each component is fundamental for the process performance. Furthermore, it can not be excluded that the same promoter may play different role depending on reaction conditions (T, composition of gas phase..). The reaction network of phthalic anhydride formation is very complex and includes several parallel and consecutive reactions; for this reason a proper understanding of the role of each dopant cannot be separated from the analysis of the reaction scheme. One of the most important promoters at industrial level, which is always present in the catalytic formulations is Cs. It is known that Cs plays an important role on selectivity to phthalic anhydride, but the reasons of this phenomenon are not really clear. Therefore the effect of Cs on the reaction scheme has been investigated at two different temperature with the aim of evidencing in which step of the reaction network this promoter plays its role.

Approccio colloidale per la preparazione di fotocatalizzatori nanostrutturati a base di TiO2

Oggigiorno si osserva a livello mondiale un continuo aumento dei consumi di acqua per uso domestico, agricolo ed industriale che dopo l’impiego viene scaricata nei corpi idrici (laghi, fiumi, torrenti, bacini, ecc) con caratteristiche chimico fisiche ed organolettiche completamente alterate, necessitando così di specifici trattamenti di depurazione. Ricerche relative a metodi di controllo della qualità dell’acqua e, soprattutto, a sistemi di purificazione rappresentano pertanto un problema di enorme importanza. I trattamenti tradizionali si sono dimostrati efficienti, ma sono metodi che operano normalmente trasferendo l’inquinante dalla fase acquosa contaminata ad un’altra fase, richiedendo perciò ulteriori processi di depurazione. Recentemente è stata dimostrata l’efficacia di sistemi nano strutturati come TiO2-Fe3O4 ottenuto via sol-gel, nella foto-catalisi di alcuni sistemi organici. Questo lavoro di tesi è rivolto alla sintesi e caratterizzazione di un catalizzatore nanostrutturato composito costituito da un core di Fe3O4 rivestito da un guscio di TiO2 separate da un interstrato inerte di SiO2, da utilizzare nella foto-catalisi di sistemi organici per la depurazione delle acque utilizzando un metodo di sintesi alternativo che prevede un “approccio” di tipo colloidale. Partendo da sospensioni colloidali dei diversi ossidi, presenti in commercio, si è condotta la fase di deposizione layer by layer via spray drying, sfruttando le diverse cariche superficiali dei reagenti. Questo nuovo procedimento permette di abbattere i costi, diminuire i tempi di lavoro ed evitare possibili alterazioni delle proprietà catalitiche della titania, risultando pertanto adatto ad una possibile applicazione su scala industriale. Tale sistema composito consente di coniugare le proprietà foto-catalitiche dell’ossido di titanio con le proprietà magnetiche degli ossidi di ferro permettendo il recupero del catalizzatore a fine processo. Il foto-catalizzatore è stato caratterizzato durante tutte la fasi di preparazione tramite microscopia SEM e TEM, XRF, Acusizer, spettroscopia Raman e misure magnetiche. L’attività foto-calitica è stata valutata con test preliminari utilizzando una molecola target tipo il rosso di metile in fase acquosa. I risultati ottenuti hanno dimostrato che il sistema core-shell presenta inalterate sia le proprietà magnetiche che quelle foto-catalitiche tipiche dei reagenti.

Un nuovo processo per la sintesi di acroleina e acido acrilico da glicerolo

La trasformazione di glicerolo ad acido acrilico può essere un fattore importante per la valorizzazione del processo di produzione di biodiesel, il quale prevede la coproduzione di enormi quantità di glicerolo. La sintesi di acido acrilico in un unico step è stata studiata attraverso vari catalizzatori solidi bifunzionali di diversa natura, contenenti proprietà acide e redox. I catalizzatori devono avere un’adeguata acidità di Brønsted per promuovere la trasformazione di glicerolo ad acroleina, mentre le proprietà ossidanti, necessarie per la sintesi di acido acrilico sono ottenute mediante l’inserimento di un metallo ossidante nella struttura. Si vuole quindi sintetizzare e testare una serie di catalizzatori che mostrino questa bifunzionalità in grado di soddisfare requisiti di attività e selettività nei confronti della reazioni . Per questo studio sono stati sintetizzati e caratterizzati ossidi misti di W/V, nella forma di aggregati dispersi sulla titania ed ossidi misti di Zr/Nb/V in struttura bulk. Sono stati quindi eseguiti dei test di reattività in fase gas ed in presenza di ossigeno utilizzando un reattore tubolare in quarzo a letto fisso.

Cluster-derived Gold/Iron catalysts for environmental applications

During the last years we assisted to an exponential growth of scientific discoveries for catalysis by gold and many applications have been found for Au-based catalysts. In the literature there are several studies concerning the use of gold-based catalysts for environmental applications and good results are reported for the catalytic combustion of different volatile organic compounds (VOCs). Recently it has also been established that gold-based catalysts are potentially capable of being effectively employed in fuel cells in order to remove CO traces by preferential CO oxidation in H2-rich streams. Bi-metallic catalysts have attracted increasing attention because of their markedly different properties from either of the costituent metals, and above all their enhanced catalytic activity, selectivity and stability. In the literature there are several studies demostrating the beneficial effect due to the addition of an iron component to gold supported catalysts in terms of enhanced activity, selectivity, resistence to deactivation and prolonged lifetime of the catalyst. In this work we tried to develop a methodology for the preparation of iron stabilized gold nanoparticles with controlled size and composition, particularly in terms of obtaining an intimate contact between different phases, since it is well known that the catalytic behaviour of multi-component supported catalysts is strongly influenced by the size of the metal particles and by their reciprocal interaction. Ligand stabilized metal clusters, with nanometric dimensions, are possible precursors for the preparation of catalytically active nanoparticles with controlled dimensions and compositions. Among these, metal carbonyl clusters are quite attractive, since they can be prepared with several different sizes and compositions and, moreover, they are decomposed under very mild conditions. A novel preparation method was developed during this thesis for the preparation of iron and gold/iron supported catalysts using bi-metallic carbonyl clusters as precursors of highly dispersed nanoparticles over TiO2 and CeO2, which are widely considered two of the most suitable supports for gold nanoparticles. Au/FeOx catalysts were prepared by employing the bi-metallic carbonyl cluster salts [NEt4]4[Au4Fe4(CO)16] (Fe/Au=1) and [NEt4][AuFe4(CO)16] (Fe/Au=4), and for comparison FeOx samples were prepared by employing the homometallic [NEt4][HFe3(CO)11] cluster. These clusters were prepared by Prof. Longoni research group (Department of Physical and Inorganic Chemistry- University of Bologna). Particular attention was dedicated to the optimization of a suitable thermal treatment in order to achieve, apart from a good Au and Fe metal dispersion, also the formation of appropriate species with good catalytic properties. A deep IR study was carried out in order to understand the physical interaction between clusters and different supports and detect the occurrence of chemical reactions between them at any stage of the preparation. The characterization by BET, XRD, TEM, H2-TPR, ICP-AES and XPS was performed in order to investigate the catalysts properties, whit particular attention to the interaction between Au and Fe and its influence on the catalytic activity. This novel preparation method resulted in small gold metallic nanoparticles surrounded by highly dispersed iron oxide species, essentially in an amorphous phase, on both TiO2 and CeO2. The results presented in this thesis confirmed that FeOx species can stabilize small Au particles, since keeping costant the gold content but introducing a higher iron amount a higher metal dispersion was achieved. Partial encapsulation of gold atoms by iron species was observed since the Au/Fe surface ratio was found much lower than bulk ratio and a strong interaction between gold and oxide species, both of iron oxide and supports, was achieved. The prepared catalysts were tested in the total oxidation of VOCs, using toluene and methanol as probe molecules for aromatics and alchols, respectively, and in the PROX reaction. Different performances were observed on titania and ceria catalysts, on both toluene and methanol combustion. Toluene combustion on titania catalyst was found to be enhanced increasing iron loading while a moderate effect on FeOx-Ti activity was achieved by Au addition. In this case toluene combustion was improved due to a higher oxygen mobility depending on enhanced oxygen activation by FeOx and Au/FeOx dispersed on titania. On the contrary ceria activity was strongly decreased in the presence of FeOx, while the introduction of gold was found to moderate the detrimental effect of iron species. In fact, excellent ceria performances are due to its ability to adsorb toluene and O2. Since toluene activation is the determining factor for its oxidation, the partial coverage of ceria sites, responsible of toluene adsorption, by FeOx species finely dispersed on the surface resulted in worse efficiency in toluene combustion. Better results were obtained for both ceria and titania catalysts on methanol total oxidation. In this case, the performances achieved on differently supported catalysts indicate that the oxygen mobility is the determining factor in this reaction. The introduction of gold on both TiO2 and CeO2 catalysts, lead to a higher oxygen mobility due to the weakening of both Fe-O and Ce-O bonds and consequently to enhanced methanol combustion. The catalytic activity was found to strongly depend on oxygen mobility and followed the same trend observed for catalysts reducibility. Regarding CO PROX reaction, it was observed that Au/FeOx titania catalysts are less active than ceria ones, due to the lower reducibility of titania compared to ceria. In fact the availability of lattice oxygen involved in PROX reaction is much higher in the latter catalysts. However, the CO PROX performances observed for ceria catalysts are not really high compared to data reported in literature, probably due to the very low Au/Fe surface ratio achieved with this preparation method. CO preferential oxidation was found to strongly depend on Au particle size but also on surface oxygen reducibility, depending on the different oxide species which can be formed using different thermal treatment conditions or varying the iron loading over the support.

Physikalische Eigenschaften kolloidaler Festkörper

In dieser Arbeit wird das Phasenverhalten fluid-kristallin und kristallin-amorph, die elastischen Eigenschaften, das Nukleationsverhalten und das diffusive Verhalten ladungsstabilisierter Kolloide aus sphärischen Polystyrol- und Polytetrafluorethylenpartikeln in wässerigen Dispersionsmitteln bei sehr geringem Fremdionengehalt systematisch untersucht. Die dazugehörigen Messungen werden an einer neuartigen selbstkonstruierten Kombinationslichtstreuapparatur durchgeführt, die die Meßmethoden der dynamischen Lichtstreuung, statischen Lichtstreuung und Torsionsresonanzspektroskopie in sich vereint. Die drei Meßmethoden sind optimal auf die Untersuchung kolloidaler Festkörper abgestimmt. Das elastische Verhalten der Festkörper kann sehr gut durch die Elastizitätstheorie atomarer Kristallsysteme beschrieben werden, wenn ein Debye-Hückel-Potential im Sinne des Poisson-Boltzmann-Cell Modells als Wechselwirkungspotential verwendet wird. Die ermittelten Phasengrenzen fluid-kristallin stehen erstmalig in guter Übereinstimmung mit Ergebnissen aus molekulardynamischen Simulationen, wenn die in der Torsionsresonanzspektroskopie bestimmte Wechselwirkungsenergie zu Grunde gelegt wird. Neben der Gleichgewichtsstruktur sind Aussagen zur Verfestigungskinetik möglich. Das gefundene Nukleationserhalten kann gut durch die klassische Nukleationstheorie beschrieben werden, wenn bei niedriger Unterkühlung der Schmelze ein Untergrund heterogener Keimung berücksichtigt wird. PTFE-Partikel zeigen auch bei hohen Konzentrationen nur geringfügige Mehrfachstreuung. Durch ihren Einsatz ist erstmals eine systematische Untersuchung des Glasübergangs in hochgeladenen ladungsstabilisierten Systemen möglich. Ladungsstabilisierte Kolloide unterscheiden sich vor allem durch ihre extreme Kristallisationstendenz von früher untersuchten Hartkugelsystemen. Bei hohen Partikelkonzentrationen (Volumenbrüche größer 10 Prozent) kann ein glasartiger Festkörper identifiziert werden, dessen physikalisches Verhalten die Existenz eines Bernalglases nahe legt. Der Glasübergang ist im Vergleich mit den in anderen kolloidalen Systemen und atomaren Systemen beobachteten Übergängen von sehr unterschiedlichem Charakter. Im verwendeten PTFE-System ist auf Grund der langreichweitigen stark repulsiven Wechselwirkung kein direkter Zugang des Glaszustandes aus der übersättigten Schmelze möglich. Der amorphe Festkörper entsteht hier aus einer nanokristallinen Phase. Die Keimrate steigt im zugänglichen Meßbereich annähernd exponentiell mit der Partikelanzahldichte, so daß man feststellen kann, daß der Glaszustand nicht durch Unterdrückung der Nukleation, sondern durch eine Forcierung derselben erreicht wird.

Grundlegende Untersuchungen zur Abbindereaktion von Zinkphosphatzement

Zusammenfassung Das Ziel der Arbeit bestand darin, mit der Aufklärung der Abbindereaktion von Zinkphosphatzement eine Grundlage für eine gezielte Modifikation bzw. Optimierung zu schaffen, insbesondere im Hinblick auf einen Einsatz als permanenter Füllungswerkstoff. Über den Abbindechemismus war bislang lediglich bekannt, daß es sich bei den primär gebildeten Reaktionsprodukten um röntgenamorphe Phasen handelt, die sich nach Wochen bzw. Monaten in das thermodynamisch stabile Reaktionsprodukt alpha-Hopeit (alpha-Zn3(PO4)2·4H2O) umwandeln.Im Rahmen der vorliegenden Arbeit gelang durch den Einsatz der Infrarot-Reflexionsspek-troskopie (DRIFT) die Identifikation von Dizink Cyclotetraphosphat-Octahydrat (Zn2P4O12·8H2O) als röntgenamorpher Vorläuferphase. Das kondensierte Phosphat ist hydrolyseempfindlich sowie thermodynamisch instabil. Mit Hilfe der zeitaufgelösten 1H NMR-Spektroskopie konnte gezeigt werden, daß bereits nach ca. 10 Minuten eine Phasenumwandlung (topochemische Disproportionierung) in ein zunächst röntgenamorphes Orthophosphat stattfindet. Mittels 31P Doppelquanten-NMR-Spektroskopie gelang der Nachweis, daß innerhalb des röntgenamorphen Bereiches lokal nahgeordnete (nanokristalline) Bereiche auftreten, deren Ordnung sich auf einer Längenskala von 10 bis 30 Å erstreckt. Die Nanokristallite unterliegen einem Wachstumsprozeß, der schließlich zu alpha-Hopeit-Kristallen mit Ausdehnungen im Mikrometerbereich führt. Die Ursache für die primäre Ausbildung röntgenamorpher Reaktionsprodukte kann zunächst gelösten Aluminophosphatkomplexen zugeordnet werden, die im Verlauf der Abbindereaktion zu anorganischen Polymeren aggregieren und damit als Kristallisationsinhibitoren fungieren.

Self assembled monolayers for engineering of structured inorganic materials in the micrometer and submicrometer range

Deutsch:In der vorliegenden Arbeit konnten neue Methoden zur Synthese anorganischer Materialien mit neuartiger Architektur im Mikrometer und Nanometer Maßstab beschrieben werden. Die zentrale Rolle der Formgebung basiert dabei auf der templatinduzierten Abscheidung der anorganischen Materialien auf selbstorganisierten Monoschichten. Als Substrate eignen sich goldbedampfte Glasträger und Goldkolloide, die eine Mittelstellung in der Welt der Atome bzw. Moleküle und der makroskopischen Welt der ausgedehnten Festkörper einnehmen. Auf diesen Substraten lassen sich Thiole zu einer monomolekularen Schicht adsorbieren und damit die Oberflächeneigenschaften des Substrates ändern. Ein besonderer Schwerpunkt bei dieser Arbeit stellt die Synthese speziell auf die Bedürfnisse der jeweiligen Anwendung ausgerichteten Thiole dar.Im ersten Teil der Arbeit wurden goldbedampfte Glasoberflächen als Template verwendet. Die Abscheidung von Calciumcarbonat wurde in Abhängigkeit der Schichtdicke der adsorbierten Monolage untersucht. Aragonit, eine der drei Hauptphasen des Calciumcarbonat Systems, wurde auf polyaromatischen Amid - Oberflächen mit Schichtdicken von 5 - 400 nm Dicke unter milden Bedingung abgeschieden. Die einstellbaren Parameter waren dabei die Kettenlänge des Polymers, der w-Substituent, die Bindung an die Goldoberfläche über Verwendung verschiedener Aminothiole und die Kristallisationstemperatur. Die Schichtdickeneinstellung der Polymerfilme erfolgte hierbei über einen automatisierten Synthesezyklus.Titanoxid Filme konnten auf Oberflächen strukturiert werden. Dabei kam ein speziell synthetisiertes Thiol zum Einsatz, das die Funktionalität einer Styroleinheit an der Oberflächen Grenze als auch eine Möglichkeit zur späteren Entfernung von der Oberfläche in sich vereinte. Die PDMS Stempeltechnik erzeugte dabei Mikrostrukturen auf der Goldoberfläche im Bereich von 5 bis 10 µm, die ihrerseits über die Polymerisation und Abscheidung des Polymers in den Titanoxid Film überführt werden konnten. Drei dimensionale Strukturen wurden über Goldkolloid Template erhalten. Tetraethylenglykol konnte mit einer Thiolgruppe im Austausch zu einer Hydroxylgruppe monofunktionalisiert werden. Das erhaltene Molekül wurde auf kolloidalem Gold selbstorganisiert; es entstand dabei ein wasserlösliches Goldkolloid. Die Darstellung erfolgte dabei in einer Einphasenreaktion. Die so erhaltenen Goldkolloide wurden als Krstallisationstemplate für die drei dimensionale Abscheidung von Calciumcarbonat verwendet. Es zeigte sich, dass Glykol die Kristallisation bzw. den Habitus des krsitalls bei niedrigem pH Wert modifiziert. Bei erhöhtem pH Wert (pH = 12) jedoch agieren die Glykol belegten Goldkolloide als Template und führen zu sphärisch Aggregaten. Werden Goldkolloide langkettigen Dithiolen ausgesetzt, so führt dies zu einer Aggregation und Ausfällung der Kolloide aufgrund der Vernetzung mehrer Goldkolloide mit den Thiolgruppen der Alkyldithiole. Zur Vermeidung konnte in dieser Arbeit ein halbseitig geschütztes Dithiol synthetisiert werden, mit dessen Hilfe die Aggregation unterbunden werden konnte. Das nachfolgende Entschützten der Thiolfunktion führte zu Goldkolloiden, deren Oberfläche Thiol funktionalisiert werden konnte. Die thiolaktiven Goldkolloide fungierten als template für die Abscheidung von Bleisulfid aus organisch/wässriger Lösung. Die Funktionsweise der Schutzgruppe und die Entschützung konnte mittels Plasmonenresonanz Spektroskopie verdeutlicht werden. Titanoxid / Gold / Polystyrol Komposite in Röhrenform konnten synthetisiert werden. Dazu wurde ein menschliches Haar als biologisches Templat für die Formgebung gewählt.. Durch Bedampfung des Haares mit Gold, Assemblierung eines Stryrolmonomers, welches zusätzlich eine Thiolfunktionalität trug, Polymerisation auf der Oberfläche, Abscheidung des Titanoxid Films und anschließendem Auflösen des biologischen Templates konnte eine Röhrenstruktur im Mikrometer Bereich dargestellt werden. Goldkolloide fungierten in dieser Arbeit nicht nur als Kristallisationstemplate und Formgeber, auch sie selbst wurden dahingehend modifiziert, dass sie drahtförmige Agglormerate im Nanometerbereich ausbilden. Dazu wurden Template aus Siliziumdioxid benutzt. Zum einen konnten Nanoröhren aus amorphen SiO2 in einer Sol Gel Methode dargestellt werden, zum anderen bediente sich diese Arbeit biologischer Siliziumoxid Hohlnadeln aus marinen Schwämmen isoliert. Goldkolloide wurden in die Hohlstrukturen eingebettet und die Struktur durch Ausbildung von Kolloid - Thiol Netzwerken mittels Dithiol Zugabe gefestigt. Die Gold-Nanodrähte im Bereich von 100 bis 500 nm wurden durch Auflösen des SiO2 - Templates freigelegt.