Análise dos Processos de Flotação e Oxidação Avançada para o Tratamento de Efluente Modelo da Indústria do Petróleo

The generation of wastes in most industrial process is inevitable. In the petroleum industry, one of the greatest problems for the environment is the huge amount of produced water generated in the oil fields. This wastewater is a complex mixture and present great amounts. These effluents can be hazardous to the environmental without adequate treatment. This research is focused in the analysis of the efficiencies of the flotation and photo-oxidation processes to remove and decompose the organic compounds present in the produced water. A series of surfactants derivated from the laurilic alcohol was utilized in the flotation to promote the separation. The experiments have been performed with a synthetic wastewater, carefully prepared with xylene. The experimental data obtained using flotation presented a first order kinetic, identified by the quality of the linear data fitting. The best conditions were found at 0.029 g.L-1 for the surfactant EO 7, 0.05 g.L-1 for EO 8, 0.07 g.L-1 for EO 9, 0.045 g.L-1 for EO 10 and 0.08 g.L-1 for EO 23 with the following estimated kinetic constants: 0.1765, 0.1325, 0.1210, 0.1531 and 0.1699 min-1, respectively. For the series studied, the most suitablesurfactant was the EO 7 due to the lower reagent consumption, higher separation rate constant and higher removal efficiency of xylene in the aqueous phase (98%). Similarly to the flotation, the photo-Fenton process shows to be efficient for degradation of xylene and promoting the mineralization of the organic charge around 90% and 100% in 90 min

Conciliação entre modelos de mecanismos avançados de oxidação eletroquímica

Many pollutants dumped in waterways, such as dyes and pesticides, have become so ubiquitous that they represent a serious threat to human health. The electrochemical oxidation is presented as an alternative clean, efficient and economic degradation of wastewater containing organic compounds and a number of advantages of this technique is to just not make use of chemical reagents, since only electrical energy is consumed during the removal of pollutants organic. However, despite being a promising alternative, still needs some tweaking in order to obtain better efficiency in the elimination of persistent pollutants. Thus, this study sought a relationship between a recently discovered phenomenon that reflects the participation of dissolved oxygen in solution in the electrochemical oxidation process, as an anomaly, present a kinetic model that shows instantaneous current efficiency (ICE) above 100% limited by theory, manifested for some experiments with phenolic compounds with H2SO4 or HClO4 as supporting electrolyte with electrodes under anodic oxidation on boron doped diamond (BDD). Therefore it was necessary to reproduce the data ICE exposes the fault model, and thus the 2-naphthol was used as phenolic compound to be oxidised at concentrations of 9, 12 and 15 mmol L-1, and H2SO4 and HClO4 to 1 mol L-1 as a supporting electrolyte under a current density of 30 mA cm-2 in an electrochemical reactor for continuous flow disk configuration, and equipped with anodes DDB at room temperature (25 oC). Experiments were performed using N2 like as purge gas for eliminate oxygen dissolved in solution so that its influence in the system was studied. After exposure of the anomaly of the ICE model and investigation of its relationship with dissolved O2, the data could be treated, making it possible for confirmation. But not only that, the data obtained from eletranálise and spectroscopic analysis suggest the involvement of other strongly oxidizing species (O3 (ozone) and O radicals and O2 -), since the dissolved O2 can be consumed during the formation of new strong oxidizing species, not considered until now, something that needs to be investigated by more accurate methods that we may know a little more of this system. Currently the performance of the electrocatalytic process is established by a complex interaction between different parameters that can be optimized, so it is necessary to the implementation of theoretical models, which are the conceptual lens with which researchers see

Extração e análise da fração lipídica da microalga monoraphidium sp., síntese e caracterização do seu biodiesel

The cultivation of microalgae biomass in order to produce biodiesel arises as an extremely promising aspect, in that the microalgae culture includes short cycle of reproduction, smaller areas for planting and residual biomass rich in protein content. The present dissertation evaluates the performance and features, through spectrometry in the region of infrared with transformed Fourier (FTIR) and spectrometry in the region of UVvisible (UV-Vis), of the extracted lipid material (LM) using different techniques of cell wall disruption (mechanical agitation at low and at high spin and agitation associated with cavitation). The technique of gas chromatography (GC) brought to light the success of alkaline transesterification in the conversion of oil into methyl monoesters (MME), which was also analyzed by spectroscopic techniques (FTIR, proton magnetic resonance (1H NMR) and carbon (13C NMR). Through thermogravimetric analysis (TGA) were analyzed the lipid material (LM), biodiesel and the microalgae biomass. The method which provided the best results concerning the efficiency in extraction of the LP of Monoraphidium sp. (12,51%) was by mechanical agitation at high spin (14 000 rpm), for 2 hours being the ideal time, as shown by the t test. The spectroscopic techniques (1H NMR, 13C NMR and FTIR) confirmed that the structure of methyl monoesters and the chromatographic data (CG) revealed a high content of saturated fatty acid esters (about 70%) being the major constituent eicosanoic acid (33,7%), which justifies the high thermal stability of microalgae biodiesel. The TGA also ratified the conversion rate (96%) of LM into MME, pointing out the quantitative results compatible with the values obtained through GC (about 98%) and confirmed the efficiency of the extraction methods used, showing that may be a good technique to confirm the extraction of these materials. The content of LM microalgae obtained (12,51%) indicates good potential for using such material as a raw material for biodiesel production, when compared to oil content which can be obtained from traditional oil for this use, since the productivity of microalgae per hectare is much larger and requires an extremely reduced period to renew its cultivation

Estudo do desempenho de catalisadores tipo Ni/CexM1-xO2 (M = Zr ou Mn) na reação de oxidação parcial do metano

One of the main applications of methane is in the production of syngas, a mixture of hydrogen and carbon monoxide. Procedures used in this process are steam reforming, CO2 reforming, partial oxidation and autothermal reforming. The present study evaluated and compared the behavior of nickel catalysts supported on mixed oxides of cerium and manganese in the partial oxidation of methane with that of nickel catalysts supported on mixed oxides of cerium and zirconium. Mixed oxides of cerium and zirconium or cerium and manganese were synthesized using two different preparation methods, the polymeric precursor based on Pechini method and combustion reaction using a microwave. This was followed by impregnation with nickel content of 15 %. Samples were calcined at 300, 800 and 900 °C and characterized by specific surface area (SSA), X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature programmed reduction (TPR) and the reaction of partial oxidation of methane. The specific areas of samples decrease with the rise in calcination temperature and after nickel impregnation. Metal-cerium solid solution was formed and the presence of other manganese species outside the solid solution structure was confirmed in the compound with the highest amounts of manganese oxides showed. With regard to scanning electron microscopy, supports based on cerium and zirconium prepared by Pechini method exhibited agglomerated particles without uniform geometry or visible pores on the surface. However, compounds containing manganese presented empty spaces in its structure. Through synthesis by combustion reaction, morphology acquired independently of the proposed composition demonstrated greater porosity in relation to Pechini synthesis. Although catalysts were prepared using different synthesis methods, the insertion of nickel showed very similar reduction profiles (TPR). In relation to nickel catalysts supported on mixed oxide of cerium and zirconium, there is an initial reduction of NiO species that present certain interaction with the support. This is followed by the reduction of Ce4+ in Ce3+ surface, with subsequent bulk reduction. For catalysts containing manganese, a reduction of nickel oxide species occurs, followed by two stages of reduction for species Mn2O3 in Mn3O4 and Mn3O4 in MnO, with subsequent reduction of bulk. With respect to partial oxidation reactions, the nickel catalyst supported on mixed oxide of cerium and zirconium, prepared using the Pechini method, exhibited CH4 conversion of approximately 80 %, with conversion of 81 % when prepared by combustion. This behavior continued for 10 hours of reaction. Manganese content was also found to directly influence catalytic activity of materials; the greater the manganese oxide content, the faster deactivation and destabilization occurred in the catalyst. In both synthesis methods, the nickel catalyst supported on mixed oxide of cerium and zirconium maintained an H2/CO ratio very close to 2 during the 10 hours of partial oxidation reaction. Samples containing manganese displayed smaller H2/CO ratios and lower performance in partial oxidation.

Degradação eletroquímica de benzeno, tolueno e xileno via oxidação eletroquímica utilizando eletrodo Ti/Pt

This work is directed to the treatment of organic compounds present in produced water from oil using electrochemical technology. The water produced is a residue of the petroleum industry are difficult to treat , since this corresponds to 98 % effluent from the effluent generated in the exploration of oil and contains various compounds such as volatile hydrocarbons (benzene, toluene, ethylbenzene and xylene), polycyclic aromatic hydrocarbons (PAHs), phenols, carboxylic acids and inorganic compounds. There are several types of treatment methodologies that residue being studied, among which are the biological processes, advanced oxidation processes (AOPs), such as electrochemical treatments electrooxidation, electrocoagulation, electrocoagulation and eletroredution. The electrochemical method is a method of little environmental impact because instead of chemical reagents uses electron through reactions of oxide-reducing transforms toxic substances into substances with less environmental impact. Thus, this paper aims to study the electrochemical behavior and elimination of the BTX (benzene, toluene and xylene) using electrode of Ti/Pt. For the experiment an electrochemical batch system consists of a continuous source, anode Ti/Pt was used, applying three densities of current (1 mA/cm2, 2,5 mA/cm2 and 5 mA/cm2). The synthetic wastewater was prepared by a solution of benzene, toluene and xylene with a concentration of 5 ppm, to evaluate the electrochemical behavior by cyclic voltammetry and polarization curves, even before assessing the removal of these compounds in solution by electrochemical oxidation. The behavior of each of the compounds was evaluated by the use of electrochemical techniques indicate that each of the compounds when evaluated by cyclic voltammetry showed partial oxidation behavior via adsorption to the surface of the Ti/Pt electrode. The adsorption of each of the present compounds depends on the solution concentration but there is the strong adsorption of xylene. However, the removal was confirmed by UV-Vis, and analysis of total organic carbon (TOC), which showed a percentage of partial oxidation (19,8 % - 99,1 % TOC removed), confirming the electrochemical behavior already observed in voltammetry and cyclic polarization curves

Determinação das doses letal 50 e 100 do propofol em nanoemulsão ou em emulsão lipídica pela via intraperitoneal em camundongos

The formulation of a drug can interfere with its absorption into the circulatory system and may result in changes in the dose required to achieve that particular effect. The aim of this study was to determine the lethal dose 50 (LD 50) and 100 (LD100) of a nanoemulsion of propofol and the lipid emulsion in mice intraperitoneally. One hundred sixty animals weighing 36.47 +/- 4.6g, which were distributed randomly into two groups: NANO and EMU who received propofol 1% in the nanoemulsion and lipid emulsion, respectively, intraperitoneally. Began with a dose of 250mg/kg (n=10) and from this isdecreased or increased the dose until achieving 0 and 100% of deaths in each group thus formed were seven subgroups in NANO (each subgroup n = 10) at doses 200, 250, 325, 350, 400, 425 and 475 mg/kg and in EMU eight subgroups (n= 10 each subset) 250, 325, 350, 400, 425, 475, 525 and 575 mg/kg. In the CONTROL group (n= 10) animals received saline in the largest volume used in the other groups to rule out death by the volume injected. Analysis of LD 50 and LD 100 were obtained by linear regression. The LD 50 was 320, 95 mg / kg and 4243, 51mg / kg and the LD 100 was445.99 mg / kg and 595.31 mg / kg to groups NANO and EMU, respectively. It follows that nanoemulsion is propofol in 25% more potent compared to the lipid emulsionintraperitoneally.

Estudo da ação do extrato de Ginkgo biloba e amido hidroxietílico hipertônico na atenuação de alterações decorrentes de isquemia e reperfusão de órgãos esplâncnicos em ratos

A oclusão e reperfusão das artérias esplâncnicas ocasiona choque circulatório, causado principalmente pelo aumento de permeabilidade vascular e pela agressão celular provocada por radicais livres derivados do oxigênio. Este estudo tem por finalidade verificar a ação do extrato de Ginkgo biloba (Egb-761) e do amido hidroxietílico (AHH) na prevenção do choque circulatório produzido pela isquemia e reperfusão de órgãos esplâncnicos. O Egb-761 tem propriedades antioxidantes relatadas na literatura. O AHH, tem sido utilizado como recurso terapêutico do choque hipovolêmico. Ratos anestesiados receberam infusão contínua de Egb-761 ou AHH, sendo submetidos à isquemia (oclusão do tronco celíaco, artéria mesentérica superior e artéria mesentérica inferior por 30 minutos) e reperfusão (por 90 minutos) dos órgãos esplâncnicos. Foram feitas: análise histopatológica ileal, dosagem de malondialdeído ileal e determinação contínua da pressão arterial média (PAM). A PAM ao final do período de reperfusão foi significativamente mais elevada nos animais tratados com Egb-761 e AHH, que no grupo controle (F=18,29; p<0,001). Não houve diferença entre os grupos tratados e controle quanto à dosagem de MDA (H=4,61; p>0,10) e quanto às alterações histológicas (H=6,003; p>0,10). em conclusão, houve melhora nas condições hemodinâmicas, com atenuação do choque nos ratos que receberam Egb-761 ou AHH. Novos estudos serão necessários para se avaliar melhor as alterações histológicas e para esclarecer a formação de produtos finais da peroxidação lipídica.

Desenvolvimento de uma rota química alternativa de síntese de SrCo0,8Fe0,2O3- e LaNi0,3Co0,7O3- para aplicação na reação de oxidação do CO

This thesis focuses on the coprecipitation synthesis method for preparation of ceramic materials with perovskite structure, their characterization and application as catalytic material in the reaction of converting CO to CO2 developing a methodological alternative route of synthesis from the middle via oxalate coprecipitation material SrCo0,8Fe0,2O3-d. In order to check the influence of this method, it was also synthesized using a combined citrate - EDTA complexing method. The material was characterized by: X-ray diffraction (XRD), Rietveld refinement method, thermogravimetry and differential thermo analysis (TG / DTA), scanning (SEM) and transmission (TEM) electron microscopy, particle size distribution and surface analysis method BET. Both methods led to post-phase synthesis, with pH as a relevant parameter. The synthesis based on the method via oxalate coprecipitation among particles led to the crystalline phase as those obtained using a combined citrate - EDTA complexing method under the same conditions of heat treatment. The nature of the reagent used via oxalate coprecipitation method produced a material with approximately 80 % lower than the average size of crystallites. Moreover, the via oxalate coprecipitation method precursors obtained in the solid state at low temperature (~ 26 oC), shorter synthesis, greater thermal stability and a higher yield of around 90-95 %, maintaining the same order of magnitude the crystallite size that the combined citrate - EDTA complexing method. For purposes of comparing the catalytic properties of the material was also synthesized by the using a combined citrate - EDTA complexing method. The evaluation of catalytic materials SrCo0,8Fe0,2O3-d LaNi0,3Co0,7O3-d was accompanied on the oxidation of CO to CO2 using a stainless steel tubular reactor in the temperature range of 75-300 oC. The conversion CO gas was evaluated in both materials on the results shaved that the firm conversion was loves for the material LaNi0,3Co0,7O3-d

Neonatally-induced diabetes: lipid profile outcomes and oxidative stress status in adult rats

INTRODUÇÃO: Modelos experimentais são desenvolvidos com propósito de ampliar o entendimento dos mecanismos fisiopatológicos envolvidos no diabete. Os achados experimentais levam ao desenvolvimento de tratamentos alternativos para a manutenção das condições metabólicas normais. Existem vários estudos sobre o diabete induzido por streptozotocin mimetizando o quadro clínico do DM2. No entanto, a interação entre os níveis de glicose, perfil lipídico e estresse oxidativo nestes animais são escassos. Portanto, o objetivo do trabalho foi avaliar estes parâmetros em ratas Wistar adultas com diabete induzido com streptozotocin no período neonatal. MÉTODOS: Fêmeas recém-nascidas receberam streptozotocin (70mg/Kg, ip) no 5º dia de vida (n5-STZ). A glicemia foi medida no terceiro e quarto meses de vida dos animais. No final do quarto mês de vida, amostras de sangue foram coletadas e processadas para a dosagem de lipídios e marcadores de estresse oxidativo. RESULTADOS: A glicemia das ratas do grupo n5-STZ foi significativamente maior comparada às ratas do grupo controle (p<0,05). Não houve alteração nos níveis de colesterol total e triglicérides, peroxidação lipídica (TBARS), atividade da SOD e determinação da GSH-t (p>0,05) nas ratas n5-STZ em relação às ratas do grupo controle. No entanto, houve diminuição significativa no HDL-colesterol (p<0,05). CONCLUSÃO: Este modelo de indução de diabete em ratas causou hiperglicemia (120-360mg/dL), caracterizando o diabete moderado. Essa glicemia levou a alterações no HDL-colesterol, a qual não foi suficiente para prejudicar a atividade das enzimas antioxidantes ou marcadores da peroxidação lipídica na vida adulta. Além disso, esta investigação experimental contribuiu para entender os diferentes resultados encontrados em outros modelos deindução do diabete moderado em animais de laboratório, como também para a melhor compreensão dos mecanismos fisiopatológicos do diabete moderado ou da hiperglicemia em humanos.

Suplementação nutricional com antioxidantes naturais: efeito da rutina na concentração de colesterol-HDL

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Antioxidant potential of oregano (Oreganum vulgare L.), basil (Ocimum basilicum L.) and thyme (Thymus vulgaris L.): application of oleoresins in vegetable oil

Por razões econômicas e de proteção à saúde, pesquisas têm sido dirigidas para ampliar a estabilidade dos óleos vegetais. Existe uma tendência para a adição de antioxidantes naturais, em particular, um crescente interesse em ervas e especiarias. Desta forma, os objetivos deste trabalho foram avaliar o potencial antioxidante das oleorresinas de orégano, manjericão e tomilho e seu comportamento ao serem aplicadas ao óleo de soja em diferentes concentrações. Numa primeira etapa foi determinada a atividade antioxidante pelo sistema β-caroteno/ácido linoleico e a quantificação de compostos fenólicos totais. Posteriormente, foram adicionadas ao óleo de soja diferentes concentrações das oleorresinas (500 a 3000 mg.kg-1) e analisado seu potencial antioxidante por meio da estabilidade oxidativa utilizando o Rancimat. A concentração de 3000 mg.kg-1das oleorresinas de orégano e tomilho foi a que apresentou melhor estabilidade oxidativa ao óleo de soja, o que as tornam alternativa natural na conservação de óleos vegetais.

Antioxidantes utilizados em óleos, gorduras e alimentos gordurosos

Lipid oxidation is certainly one of the most important alterations that affect both oils or fats and foods that contain them. It is responsible for the development of unpleasant taste and smell in foods, making them unsuitable for consuming. The use of antioxidants permits a longer useful life of these products. This work presents a bibliographic review of research carried out in order to evaluate the antioxidant activity of natural or synthetic substances used in the conservation of food lipid. Among such substances, the following antioxidants are highlighted: butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT), tertiary butylhydroquinone (TBHQ), propyl gallate (PG), tocopherols, phenolic acids and isolated compounds from rosemary and oregano.

Avaliação do óleo de girassol adicionado de antioxidantes sob estocagem

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo da oxidação dos sulfetos sintéticos molibdenita (MoS2) e covelita (CuS) por Acidithiobacillus ferrooxidans via respirometria celular

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Electrochemical evaluation of lipophilic antioxidants from Iryanthera juruensis fruits (Myristicaceae)

Testes em placas de CCDC reveladas com solução de beta-caroteno mostraram a presença de duas substâncias com propriedades antioxidantes no extrato hexânico. Elas foram isoladas e identificadas como 3-metil-sargacromenol (1) and sargacromenol (2). O extrato hexânico forneceu ainda o ácido 3-metil-sargaquinóico (3) e o ácido sargaquinóico (4). O comportamento eletroquímico destas substâncias foi investigado em CH2Cl2/Bu4NBF4 sobre eletrodo de carbono vítreo. A oxidação do grupo fenólico nos tocotrienóis 1 and 2 é responsável por um pico anódico em potenciais de +0.23V e +0.32V, os quais são correlacionados com sua atividade antioxidante. O mecanismo de oxidação é comparado com o comportamento eletroquímico do antioxidante alfa-tocopherol.