El fotorreactor elíptico

In this paper, the mathematical model of the elliptical photoreactor , an special type of reactor that uses ultraviolet radiation, is presented. In the elliptical photoreactor the cylindrical reactor is irradiated from the outside by placing the lamp and the reactor at the foci of an elliptical reflector. The two main models of radiation -radial and difusse- are studied, an finally the general method of resolution of the mathematical model and its resolution in certain simple cases is shown.

Comparison of a deterministic and a data driven model to describe MBR fouling

Membrane bioreactors (MBRs) are a combination of activated sludge bioreactors and membrane filtration, enabling high quality effluent with a small footprint. However, they can be beset by fouling, which causes an increase in transmembrane pressure (TMP). Modelling and simulation of changes in TMP could be useful to describe fouling through the identification of the most relevant operating conditions. Using experimental data from a MBR pilot plant operated for 462days, two different models were developed: a deterministic model using activated sludge model n°2d (ASM2d) for the biological component and a resistance in-series model for the filtration component as well as a data-driven model based on multivariable regressions. Once validated, these models were used to describe membrane fouling (as changes in TMP over time) under different operating conditions. The deterministic model performed better at higher temperatures (>20°C), constant operating conditions (DO set-point, membrane air-flow, pH and ORP), and high mixed liquor suspended solids (>6.9gL-1) and flux changes. At low pH (<7) or periods with higher pH changes, the data-driven model was more accurate. Changes in the DO set-point of the aerobic reactor that affected the TMP were also better described by the data-driven model. By combining the use of both models, a better description of fouling can be achieved under different operating conditions

Towards integrated operation of membrane bioreactors : effects of aeration on biological and filtration performance

Two experimental studies evaluated the effect of aerobic and membrane aeration changes on sludge properties, biological nutrient removal and filtration processes in a pilot plant membrane bioreactor. The optimal operating conditions were found at an aerobic dissolved oxygen set-point (DO) of 0.5mgO2L-1 and a membrane specific aeration demand (SADm) of 1mh-1, where membrane aeration can be used for nitrification. Under these conditions, a total flow reduction of 42% was achieved (75% energy reduction) without compromising nutrient removal efficiencies, maintaining sludge characteristics and controlled filtration. Below these optimal operating conditions, the nutrient removal efficiency was reduced, increasing 20% for soluble microbial products, 14% for capillarity suction time and reducing a 15% for filterability. Below this DO set-point, fouling increased with a transmembrane pressure 75% higher. SADm below 1mh-1 doubled the values of transmembrane pressure, without recovery after achieving the initial conditions

Alargamento da distribuição de massa molar de polímeros sintetizados com catalisadores metalocênicos dual-site

The main topics related to the use of dual-site catalysts in the production of polymers with broad molecular weight distribution are reviewed. The polymerization using dual-site catalysts is more economical and allows to produce a higher quality product than other processes, such as polymer blend and multistage reactors. However, the formulation of these catalysts is quite complicated since the same catalyst must produce distinct polymer grades. In addition, the release of patents concerning the combination of metallocenes and new technologies for polymerization shows that polymerization processes using dual-site catalysts are of current industrial interest.

Imobilização de enzimas em suportes cromatográficos: uma ferramenta na busca por substâncias bioativas

The development and characterization of bioreactors or IMER (immobilized enzyme reactors) as research tools are important in the scope of medicinal chemistry and constitute an alternative for the rational development of drugs. This approach does not require highly purified enzymes or a great amount of protein, but increase the enzymatic stability against heat, organic solvents and pH, without too much loss of catalyst activity. Immobilized enzyme reactors (IMER) can be used for the accomplishment of high efficiency screening on-line and, thus inhibitors can be quickly identified. Here, we emphasize the development of IMER by use of different methods of immobilization and chromatographic supports. Their applications, in different areas of research, are also fully discussed.

Caracterização de cinza obtida por combustão de casca de arroz em reator de leito fluidizado

The rice husk combustion in a bubbling and atmospheric fluidized bed reactor was investigated. This paper presents the rice husk ash characterization employing the techniques of X-ray diffraction (XRD), X-ray fluorescence (XRF), and scanning electron microscopy (SEM) among others. After combustion, a rice husk ash containing 93% amorphous silica and <3% unburned char was produced. Methods usually applied to fixed bed considering external sources of energy and high reaction times were employed. Thus, the potential of this type of reactors with respect to speed, continuity and self-sufficiency energy of the process was shown.

Descoloração redutiva de corantes azo e o efeito de mediadores redox na presença do aceptor de elétrons sulfato

We investigated the impact of sulphate and the redox mediator Anthraquinone-2,6-disulfonate (AQDS) on the decolorization of the azo dyes Congo Red (CR) and Reactive Black 5 (RB5). In anaerobic reactors free of extra sulphate dosage, the color removal efficiency decreased drastically when the external electron donor ethanol was removed. In presence of an extra dosage of sulphate, CR decolourisations were 47.8% (free of AQDS) and 96.5% (supplemented with AQDS). The decolourisations achieved in both reactors with RB5 were lower than the ones found with CR. Finally, the biogenic sulphide contribution on azo dye reduction was negligiable.

Validação de método para determinação de ácidos orgânicos voláteis em efluentes de reatores anaeróbios empregando cromatografia líquida

This work deals with the method validation for the determination of acetic, propionic and butyric acids (VFAs) in wastewaters from anaerobic reactors by HPLC-DAD. Separation was performed using a C18 column and the mobile phase composition were water pH 3.0 and methanol 90:10 (v/v). The detection and quantification was carried out at 220 nm. The method shows good linearity (r²>0.996), with adequate accuracy (89-102%) and relative standard deviations lower than 18%. The matrix effect was considered low (-4.1, -3.9 and 1.4%). The developed method is fast, simple and cheap; and it was applied in wastewater samples from anaerobic reactor.

Removal of high-molecular weight polycyclic aromatic hydrocarbons

Alternatives for the removal of high-molecular weight polycyclic aromatic hydrocarbons (HWM-PAH) from soil were tested by adding fertilizer or glycerol, as well as the combination of both. Experiments were carried out for 60 days in reactors containing a HWM-PAH-contaminated soil (8030 μg kg-1), accompanied by pH monitoring, humidity control and quantification of total heterotrophic bacteria and total fungus. Fertilizer addition removed 41.6% of HWM-PAH. Fertilizer and glycerol in combination removed 46.2%. When glycerol was added individually, degradation reached 50.4%. Glycerol also promoted the increase of degradation rate during the first 30 days suggesting the HMW-PAH removal occurred through cometabolic pathways.

Atual estágio de desenvolvimento da tecnologia GTL e perspectivas para o Brasil

Although the production of liquid fuels from coal, natural gas (CTL and GTL processes) and other carbon sources has been discovered 90 years ago, the interest was renewed in the last years motivated by stranded gas reserves and by petroleum market instability. This review intends to show the scenario of these technologies nowadays, discussing the applied technologies, the steps in an industrial plant, the ways to produce syngas and liquid fuels, the catalysts used, the type of reactors and the operating plants with their respective capacities, besides the technical, economical and environmental viability, challenges and perspectives for Brazil.

Determinação de parâmetros cinéticos em fluxo com câmara de gradiente e deteção espectrofotométrica: aplicação à reação entre o violeta de cristal e o ião hidróxido

A didactic experiment is proposed aimed to extend the Flow Injection Analysis (FIA) based methodology to the area of physical chemistry/chemical reactors for undergraduate labs. Our prime objective was to describe the use of a gradient chamber for determination of the rate constant for the reaction between crystal violet and the hydroxide ion. The study was complemented by determining the effect of temperature on the rate constant. The kinetic parameters, activation energy and reaction rate constant are determined based on an assumption of rate orders. The main didactic advantages of the proposed experimental set-up are the use of less reagents, contributing to a more environmental friendly experiment. The experiment illustrates also the reduction of associated errors and time by using automated analysis owing to decreased operator manipulation.

Imobilização de lacase de Aspergillus sp. em quitosana e sua aplicação na bioconversão de fenóis em reatores de leito fixo

The immobilization of laccase on chitosan by cross-linking and application of the immobilized laccase in the bioconversion of phenolic compounds in batch and fixed bed reactors were studied. The process for immobilization of enzyme was optimized using a rotational central composite design. The optimized conditions to generate immobilized laccase with maximal activity were determined to be a glutaraldehyde concentration of 1.0% (v/v), a pH of 6.0, an immobilization time of 5.0 hours and an enzyme concentration of 5.2 g L-1. In packed bed reactors, the activity of the immobilized enzyme is maintained for a longer time in the bioconversion of 2,6-dimethoxyphenol than in the bioconversion of syringaldazine.

Advances in ethanol reforming for the production of hydrogen

Catalytic steam reforming of ethanol (SRE) is a promising route for the production of renewable hydrogen (H2). This article reviews the influence of doping supported-catalysts used in SRE on the conversion of ethanol, selectivity for H2, and stability during long reaction periods. In addition, promising new technologies such as membrane reactors and electrochemical reforming for performing SRE are presented.

Desenvolvimento de reator tipo "dip catalyst" para filmes poliméricos contendo nanopartículas de metais de transição

This article describes the development of a new catalytic reactor designed to operate with nanoparticle-embedded polymer thin films. Stabilization of metal nanoparticles in films that serve as catalysts in organic reactions is relatively new; therefore, the development of reactors to facilitate their use is necessary. We describe in detail the preparation of the GDCR reactor-type "dip catalyst" and its evaluation in the Suzuki - Miyaura cross-coupling reaction of phenylboronic acid and 4-bromoanisole catalyzed by palladium nanoparticle-embedded cellulose acetate thin film (CA/PD(0)). Compared with earlier prototypes, GDCR reactor showed excellent results when operating with CA/PD(0) thin films.

COMPARAÇÃO E CONSTRUÇÃO DE REATORES DE "MILD" E "HARD ANODISATION" PARA FABRICAÇÃO DE ALUMINA ANÓDICA POROSA

The mild anodization (MA) reactor is exemplified for its operational simplicity and its excellent control over the experimental parameters that are involved in the anodization process. This method provides porous anodic alumina films with a regular cell-arrangement structure. This offers a better cost-benefit ratio than the other equipment configurations that are used to fabricate nanoporous structures (i.e., ion beam lithography). Conversely, the hard anodization (HA) reactor produces oxides at a rate that is 25 to 35 times faster than the MA reactor. The produced oxides also have greater layer thicknesses and interpore distance, and with a uniform nanopore spatial order (> 1000). In contrast to MA reactors, the construction of an HA reactor requires special components to maintain anodisation at a high potential regime. Herein, we describe and compare both reactors from a technical viewpoint.