Novo método para estimativa do gradiente de fratura para poços de petróleo

The development of oil wells drilling requires additional cares mainly if the drilling is in offshore ultra deep water with low overburden pressure gradients which cause low fracture gradients and, consequently, difficult the well drilling by the reduction of the operational window. To minimize, in the well planning phases, the difficulties faced by the drilling in those sceneries, indirect models are used to estimate fracture gradient that foresees approximate values for leakoff tests. These models generate curves of geopressures that allow detailed analysis of the pressure behavior for the whole well. Most of these models are based on the Terzaghi equation, just differentiating in the determination of the values of rock tension coefficient. This work proposes an alternative method for prediction of fracture pressure gradient based on a geometric correlation that relates the pressure gradients proportionally for a given depth and extrapolates it for the whole well depth, meaning that theses parameters vary in a fixed proportion. The model is based on the application of analytical proportion segments corresponding to the differential pressure related to the rock tension. The study shows that the proposed analytical proportion segments reaches values of fracture gradient with good agreement with those available for leakoff tests in the field area. The obtained results were compared with twelve different indirect models for fracture pressure gradient prediction based on the compacting effect. For this, a software was developed using Matlab language. The comparison was also made varying the water depth from zero (onshore wellbores) to 1500 meters. The leakoff tests are also used to compare the different methods including the one proposed in this work. The presented work gives good results for error analysis compared to other methods and, due to its simplicity, justify its possible application

Simulação do escoamento monofásico em um estágio de uma bomba centrífuga utilizando técnicas de fluidodinâmica computacional

Oil production and exploration techniques have evolved in the last decades in order to increase fluid flows and optimize how the required equipment are used. The base functioning of Electric Submersible Pumping (ESP) lift method is the use of an electric downhole motor to move a centrifugal pump and transport the fluids to the surface. The Electric Submersible Pumping is an option that has been gaining ground among the methods of Artificial Lift due to the ability to handle a large flow of liquid in onshore and offshore environments. The performance of a well equipped with ESP systems is intrinsically related to the centrifugal pump operation. It is the pump that has the function to turn the motor power into Head. In this present work, a computer model to analyze the three-dimensional flow in a centrifugal pump used in Electric Submersible Pumping has been developed. Through the commercial program, ANSYS® CFX®, initially using water as fluid flow, the geometry and simulation parameters have been defined in order to obtain an approximation of what occurs inside the channels of the impeller and diffuser pump in terms of flow. Three different geometry conditions were initially tested to determine which is most suitable to solving the problem. After choosing the most appropriate geometry, three mesh conditions were analyzed and the obtained values were compared to the experimental characteristic curve of Head provided by the manufacturer. The results have approached the experimental curve, the simulation time and the model convergence were satisfactory if it is considered that the studied problem involves numerical analysis. After the tests with water, oil was used in the simulations. The results were compared to a methodology used in the petroleum industry to correct viscosity. In general, for models with water and oil, the results with single-phase fluids were coherent with the experimental curves and, through three-dimensional computer models, they are a preliminary evaluation for the analysis of the two-phase flow inside the channels of centrifugal pump used in ESP systems

Sistema de sensoriamento eletromagnético utilizado para detecção da contaminação do óleo isolante do motor no método de elevação artificial do tipo bombeio centrífugo submerso

In the artificial lift method by Electrical Submersible Pump (ESP), the energy is transmitted for the well´s deep through a flat electric handle, where it is converted into mechanical energy through an engine of sub-surface, which is connected to a centrifugal pump. This transmits energy to the fluid under the pressure form, bringing it to the surface In this method the subsurface equipment is basically divided into: pump, seal and motor. The main function of the seal is the protect the motor, avoiding the motor´s oil be contaminated by oil production and the consequent burning of it. Over time, the seal will be wearing and initiates a contamination of motor oil, causing it to lose its insulating characteristics. This work presents a design of a magnetic sensor capable of detecting contamination of insulating oil used in the artificial lift method of oil-type Electrical Submersible Pump (ESP). The objective of this sensor is to generate alarm signal just the moment when the contamination in the isolated oil is present, enabling the implementation of a predictive maintenance. The prototype was designed to work in harsh conditions to reach a depth of 2000m and temperatures up to 150°C. It was used a simulator software to defined the mechanical and electromagnetic variables. Results of field experiments were performed to validate the prototype. The final results performed in an ESP system with a 62HP motor showed a good reliability and fast response of the prototype.

Efeito da adição de cargas minerais leves na resistência mecânica de grautes para cimentação de poços offshore

The preparation of cement slurries for offshore well cementing involves mixing all solid components to be added to the mixing water on the platform. The aim of this work was to study the formulation of pre-prepared dry mixtures, or grouts, for offshore oilwell cementing. The addition of mineral fillers in the strength of lightweight grouts applied for depths down to 400 m under water depths of 500 m was investigated. Lightweight materials and fine aggregates were selected. For the choice of starting materials, a study of the pozzolanic activity of low-cost fillers such as porcelain tile residue, microsilica and diatomaceous earth was carried out by X-ray diffraction and mechanical strength tests. Hardened grouts containing porcelain tile residue and microsilica depicted high strength at early ages. Based on such preliminary investigation, a study of the mechanical strength of grouts with density 1.74 g/cm3 (14.5 lb/gal) cured initially at 27 °C was performed using cement, microsilica, porcelain tile residue and an anti-foaming agent. The results showed that the mixture containing 7% of porcelain tile residue and 7% of microsilica was the one with the highest compressive strength after curing for 24 hours. This composition was chosen to be studied and adapted for offshore conditions based on testes performed at 4 °C. The grout containing cement, 7% of porcelain tile residue, 7% of active silica and admixtures (CaCl2), anti-foaming and dispersant resulted satisfactory rheology and mechanical strength after curing for 24 hours of curing

Análise paramétrica da injeção de vapor e solvente em reservatórios de óleo pesado

A significant fraction of the hydrocarbon reserves in the world is formed by heavy oils. From the thermal methods used to recovery these resources, Steamflooding has been one of the main economically viable alternatives. In Brazil, this technology is widely used by Petrobras in Northeast fields. Latent heat carried by steam heats the oil in the reservoir, reducing its viscosity and facilitating the production. In the last years, an alternative more and more used by the oil industry to increase the efficiency of this mechanism has been the addition of solvents. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a low viscosity zone between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method and investigate its applicability in reservoirs with properties similar to those found in Potiguar Basin, a numerical study was done to analyze the influence of some operational parameters (steam injection rate, injected solvent volume and solvent type) on oil recovery. Simulations were performed in STARS ("Steam, Thermal, and Advanced Processes Reservoir Simulator"), a CMG ("Computer Modelling Group") program, version 2009.10. It was found that solvents addition to the injected steam not only anticipated the heated oil bank arrival to the producer well, but also increased the oil recovery. Lower cold water equivalent volumes were required to achieve the same oil recoveries from the models that injected only steam. Furthermore, much of the injected solvent was produced with the oil from the reservoir

Metodologia para avaliação de cinemática de partículas gasosas em fluidos de viscosidade variável com o tempo e sua aplicação na construção de poços de petróleo

Many challenges have been presented in petroleum industry. One of them is the preventing of fluids influx during drilling and cementing. Gas migration can occur as result of pressure imbalance inside the well when well pressure becomes lower than gas zone pressure and in cementing operation this occurs during cement slurry transition period (solid to fluid). In this work it was developed a methodology to evaluate gas migration during drilling and cementing operations. It was considered gel strength concept and through experimental tests determined gas migration initial time. A mechanistic model was developed to obtain equation that evaluates bubble displacement through the fluid while it gels. Being a time-dependant behavior, dynamic rheological measurements were made to evaluate viscosity along the time. For drilling fluids analyzed it was verified that it is desirable fast and non-progressive gelation in order to reduce gas migration without affect operational window (difference between pore and fracture pressure). For cement slurries analyzed, the most appropriate is that remains fluid for more time below critical gel strength, maintaining hydrostatic pressure above gas zone pressure, and after that gels quickly, reducing gas migration. The model developed simulates previously operational conditions and allow changes in operational and fluids design to obtain a safer condition for well construction

Controle aplicado a poços com método de elevação e bombeio centrífugo submerso

The Electrical Submersible Pumping is an artificial lift method for oil wells employed in onshore and offshore areas. The economic revenue of the petroleum production in a well depends on the oil flow and the availability of lifting equipment. The fewer the failures, the lower the revenue shortfall and costs to repair it. The frequency with which failures occur depends on the operating conditions to which the pumps are submitted. In high-productivity offshore wells monitoring is done by operators with engineering support 24h/day, which is not economically viable for the land areas. In this context, the automation of onshore wells has clear economic advantages. This work proposes a system capable of automatically control the operation of electrical submersible pumps, installed in oil wells, by an adjustment at the electric motor rotation based on signals provided by sensors installed on the surface and subsurface, keeping the pump operating within the recommended range, closest to the well s potential. Techniques are developed to estimate unmeasured variables, enabling the automation of wells that do not have all the required sensors. The automatic adjustment, according to an algorithm that runs on a programmable logic controller maintains the flow and submergence within acceptable parameters avoiding undesirable operating conditions, as the gas interference and high engine temperature, without need to resort to stopping the engine, which would reduce the its useful life. The control strategy described, based on modeling of physical phenomena and operational experience reported in literature, is materialized in terms of a fuzzy controller based on rules, and all generated information can be accompanied by a supervisory system

Modelagem molecular na caracterização eletrônica de oligopeptídeos e na descrição quântica da interação fármaco-receptor

In this dissertation, the theoretical principles governing the molecular modeling were applied for electronic characterization of oligopeptide α3 and its variants (5Q, 7Q)-α3, as well as in the quantum description of the interaction of the aminoglycoside hygromycin B and the 30S subunit of bacterial ribosome. In the first study, the linear and neutral dipeptides which make up the mentioned oligopeptides were modeled and then optimized for a structure of lower potential energy and appropriate dihedral angles. In this case, three subsequent geometric optimization processes, based on classical Newtonian theory, the semi-empirical and density functional theory (DFT), explore the energy landscape of each dipeptide during the search of ideal minimum energy structures. Finally, great conformers were described about its electrostatic potential, ionization energy (amino acids), and frontier molecular orbitals and hopping term. From the hopping terms described in this study, it was possible in subsequent studies to characterize the charge transport propertie of these peptides models. It envisioned a new biosensor technology capable of diagnosing amyloid diseases, related to an accumulation of misshapen proteins, based on the conductivity displayed by proteins of the patient. In a second step of this dissertation, a study carried out by quantum molecular modeling of the interaction energy of an antibiotic ribosomal aminoglicosídico on your receiver. It is known that the hygromycin B (hygB) is an aminoglycoside antibiotic that affects ribosomal translocation by direct interaction with the small subunit of the bacterial ribosome (30S), specifically with nucleotides in helix 44 of the 16S ribosomal RNA (16S rRNA). Due to strong electrostatic character of this connection, it was proposed an energetic investigation of the binding mechanism of this complex using different values of dielectric constants (ε = 0, 4, 10, 20 and 40), which have been widely used to study the electrostatic properties of biomolecules. For this, increasing radii centered on the hygB centroid were measured from the 30S-hygB crystal structure (1HNZ.pdb), and only the individual interaction energy of each enclosed nucleotide was determined for quantum calculations using molecular fractionation with conjugate caps (MFCC) strategy. It was noticed that the dielectric constants underestimated the energies of individual interactions, allowing the convergence state is achieved quickly. But only for ε = 40, the total binding energy of drug-receptor interaction is stabilized at r = 18A, which provided an appropriate binding pocket because it encompassed the main residues that interact more strongly with the hygB - C1403, C1404, G1405, A1493, G1494, U1495, U1498 and C1496. Thus, the dielectric constant ≈ 40 is ideal for the treatment of systems with many electrical charges. By comparing the individual binding energies of 16S rRNA nucleotides with the experimental tests that determine the minimum inhibitory concentration (MIC) of hygB, it is believed that those residues with high binding values generated bacterial resistance to the drug when mutated. With the same reasoning, since those with low interaction energy do not influence effectively the affinity of the hygB in its binding site, there is no loss of effectiveness if they were replaced.

Avaliação da atividade antimalárica de extratos obtidos de algas marinhas no litoral do Rio Grande do Norte

Malaria is a major parasitic disease worldwide, accounting for about 500 million cases and causing 2 million to 3 million deaths annually. Four species are responsible for transmitting this disease to humans: Plasmodium falciparum, Plasmodium vivax, Plasmodium malariae and Plasmodium ovale. The parasite resistance to antimalarial drugs and the usual limitations of the vector control implications are contributing to the spread of the disease. The most of significant advances in the search for new antimalarial drugs is based on natural components, the main ones being currently used antimalarial drugs derived from plants. Research on natural products of marine origin (particularly algae) show that some species possess antiplasmodial activity. Knowing that the coast of Rio Grande do Norte is home to several species of algae, the present study was to evaluate, for the first time, the antimalarial activity of ethanolic extracts of seaweed Spatoglossum schroederi, Gracilaria birdiae and Udotea flabellum against Plasmodium falciparum 3D7 strain tests and in vitro using the murine model (Plasmodium berghei) for evaluation in vivo. These species were ground, macerated with ethanol for 24 hours and the extracts concentrated in rotaevaporador (45 ° C ± 5 ° C). For in vitro tests, the extracts were diluted and tested at concentrations between 100 and 1.56 μg/ml (seven concentrations in triplicate), in order to obtain IC50 of each extract. The cytotoxicity tests with macrophages and BGM were performed using the MTT colorimetric assay. BGM macrophages and cells were distributed in 96 wells per plate (1x 105 to macrophages and 1x104 cells per well for BGM) and incubated for 24h at 37 ° C. The ethanol extracts were diluted and tested at concentrations of 100 to 1,56 μg/ml (seven concentrations in triplicate). After periods of 24 hours of incubation with the extracts, 100 μg of MTT was added to each well, and 3 hours elapsed, the supernatant was removed and added 200 μl of DMSO in each well. The absorbance of each well was obtained by reading on a spectrophotometer at 570 nm filter. To evaluate the acute toxicity in vivo, Swiss mice received a single dose (oral) 2000 mg/kg/animal of each extract tested. The parameters of acute toxicity were observed for 8 days. For in vivo tests, Swiss mice were inoculated with 1x105 erythrocytes infected with P. berghei. The treatment was given first to fourth day after infection with 0.2 ml of the extracts in doses of 1000 and 500 mg//g animal. The negative control group received 0.2 ml of 2% Tween-20, whereas the positive control group received sub-dose of chloroquine (5 mg/kg/animal). The assessment of antimalarial activity was done by suppressing suppressing the parasitemia at 5 and 7 days after infection. The growth inhibition of parasites was determined relative to negative control (% inhibition = parasitaemia in control - parasitemia in sample / parasitemia control x 100), the mortality of animals was monitored daily for 30 days The results showed that algae Spatoglossum schroederi and Udotea flabellum showed antimalarial activity in vitro, with reduced parasitemia of 70.54% and 54, respectively. The extracts of the three algae tested showed moderate to high cytotoxicity. Algae S. schroederi and U. flabellum were active against P. berghei only at doses of 500 mg / kg with reduction ranging from 54.58 to 52.65% for the fifth day and from 32.24 to 47.34% for the seventh day, respectively. No toxicity was observed in vivo at the dose tested, over the 8 days of observation. Although preliminary data, the bioactive components in those possible seaweed may be promising for the development of new anti-malarial drugs

Aditivos químicos e biológicos na ensilagem de cana-de-açúcar: 1. composição química das silagens, ingestão, digestibilidade e comportamento ingestivo

Avaliou-se o efeito da inclusão de aditivos na ensilagem de cana-de-açúcar (Saccharum officinarum L.) sobre a composição químico-bromatológica das silagens, o comportamento ingestivo, o consumo voluntário e a digestibilidade em bovinos de corte. Utilizaram-se cinco novilhos da raça Nelore providos de cânula ruminal, alocados em delineamento quadrado latino 5 ´ 5 e alimentados com dietas com 65% de volumoso na MS. Foram avaliadas cinco silagens (base úmida): controle - cana-de-açúcar sem aditivos; uréia - cana-de-açúcar + 0,5% uréia; benzoato - cana-de-açúcar + 0,1% de benzoato de sódio; LP - cana-de-açúcar inoculada com Lactobacillus plantarum (1 ´ 10(6) ufc/g MV); LB - cana-de-açúcar inoculada com L. buchneri (3,6 ´ 10(5) ufc/g forragem). A forragem foi armazenada em silos do tipo poço por 90 dias antes do fornecimento aos animais. A composição químico-bromatológica da cana-de-açúcar foi alterada após a ensilagem, em relação à cana-de-açúcar original, com redução no teor de carboidratos solúveis e na digestibilidade in vitro e elevação relativa nos teores de FDN e FDA. Os teores de etanol (0,30% da MS) e ácidos orgânicos (0,99% de ácido lático e 2,31% de acético) foram baixos e semelhantes entre as silagens. Os aditivos aplicados na ensilagem não promoveram alterações no consumo e na digestibilidade aparente da MS (7,2 kg/dia e 63,6%, respectivamente). O comportamento ingestivo dos animais também não foi alterado, com tempos médios de 230,6; 519,6 e 672,8 minutos/dia despendidos com ingestão de ração, ruminação e ócio, respectivamente. Os aditivos acrescidos à cana-de-açúcar promoveram pequenas alterações na maioria das variáveis avaliadas.

Aditivos químicos ou biológicos na ensilagem de cana-de-açúcar: 2. parâmetros ruminais e degradabilidade da matéria seca e das frações fibrosas

Objetivou-se avaliar o efeito da inclusão de aditivos na ensilagem de cana-de-açúcar (Saccharum officinarum L.) sobre a degradação de MS e de componentes da parede celular e sobre os parâmetros de fermentação ruminal em bovinos alimentados com dietas contendo essas silagens. Utilizaram-se cinco novilhos da raça Nelore providos de cânula ruminal, alocados em delineamento quadrado latino 5 ´ 5 e alimentados com dietas com 65% de volumoso (%) MS. Foram avaliadas cinco silagens (base úmida): controle - cana-de-açúcar, sem aditivos; uréia - cana-de-açúcar + 0,5% ureia; benzoato - cana-de-açúcar + 0,1% de benzoato de sódio; LP - cana-de-açúcar inoculada com Lactobacillus plantarum (1 ´ 10(6) ufc/g MV); LB - cana-de-açúcar inoculada com L. buchneri (3,6 ´ 10(5) ufc/g forragem). A forragem foi armazenada em silos do tipo poço por 90 dias antes do fornecimento aos animais. Os parâmetros ruminais foram afetados de forma moderada pelas silagens e tiveram forte efeito do horário de coleta de amostras. As concentrações molares médias dos ácidos acético, propiônico e butírico foram de 60,9; 19,3 e 10,2 mM, respectivamente. O ambiente ruminal proporcionado por dietas formuladas com silagens de cana-de-açúcar foi satisfatório e similar ao tradicionalmente observado em dietas contendo cana. O uso de aditivos na ensilagem influenciou, de forma não-significativa, a degradabilidade ruminal da MS e da MO, mas não alterou a degradabilidade ruminal da fração fibrosa. Os aditivos aplicados à cana-de-açúcar resultaram em pequenas alterações na maior parte das variáveis avaliadas. Apesar de a degradabilidade ruminal das silagens ter sido pouco afetada pelo uso de aditivos, os valores observados foram próximos aos observados para a cana-de-açúcar in natura.

Efeitos da aplicação de herbicidas sobre a eficiência fotoquímica em plantas de soja convencional e geneticamente modificada

Objetivou-se, neste trabalho, avaliar o efeito da aplicação de herbicidas em pós-emergência sobre a eficiência fotoquímica de duas cultivares de soja (M-SOY 7908 RR e M-SOY 8001). O delineamento experimental utilizado foi em blocos ao acaso, com quatro repetições. Os tratamentos constaram da aplicação de herbicidas isolados e em misturas: lactofen, glyphosate, lactofen + chlorimuron-ethyl, chlorimuron-ethyl + imazethapyr, chlorimuron-ethyl + bentazon, glyphosate + imazethapyr, lactofen + chlorimuron-ethyl + imazethapyr e lactofen + chlorimuron-ethyl + imazethapyr/haloxyfop-methyl. Além disso, foram mantidas duas testemunhas sem aplicação de herbicida. As avaliações foram realizadas aos 4; 11; 18; 25 e 32 dias após aplicação dos herbicidas (DAA) no primeiro ano, e aos 6, 14, 21, 28 e 35 DAA, no segundo. A cultivar M-SOY 8001 foi suscetível à aplicação dos herbicidas, principalmente às misturas contendo lactofen + chlorimuron-ethyl e lactofen + chlorimuron-ethyl + imazethapyr + haloxifop-methyl, os quais provocaram redução no rendimento quântico máximo do PSII (Fv/Fm). As duas cultivares apresentaram suscetibilidade aos herbicidas quando tratados com lactofen aplicado isolado e nas misturas lactofen + chlorimuron-ethyl, chlorimuron-ethyl + imazethapyr, lactofen + chlorimuron-ethyl + imazethapyr e lactofen + chlorimuron-ethyl + imazethapyr + haloxifop-methyl com redução nos teores de clorofila, estimados pelo Medidor Portátil de Clorofilas. Os danos foram reversíveis, desaparecendo gradativamente com a idade das plantas.

Teodora e Porcina: faces simbólicas da natureza em narrativas de mulheres sábias

This research looks at the collective imagination in which it keeps alive the issue of heroin wise. Two wise women appear in the narratives of popular history and the History of Donzela Theodora and History Imperatriz Porcina, collated by Luís da Câmara Cascudo in his Five Books of the People. The universality, mobility and circularity of these narratives are discussed by authors such as Bakhtin and Guinzburg. The research is developed from three key categories: Knowledge Magic as the knowledge of tradition (Almeida), sensitive knowledge (Levi-Strauss), thought mythical / magical / symbolic (Morin); Wise Women as carriers of this knowledge, which merge and overlap with the imagery of witches and healers; and Mythical Elements which corresponds to the archetypal images (Jung and Silveira), symbols and other images that relate to the magic universe, the magical beliefs and practices considered, ie belonging to the imaginary magic (Bethencourt). Porcina and Theodora are understood as bearers of knowledge of Métis (Detienne and Vernant), or the cunning intelligence, the manipulation of phármakon (Derrida), the healing potion, which may be the word or ointment of the herb. The route takes us to meet the great archetype of the Wise Woman as psychic power of the feminine, the anima. Narratives are medicinal balms (Estes) and is the clash between the anima and its embodiments by wise women, and animus, his opponents, which gives the transmutation of the psyche, a work comparable to that of alchemyThe Knowledge Magic, operating through the female, myth and nature can recover from its essential value to the emerging paradigm that suggests a more complete human science and a more plural

O princípio constitucional da eficiência aplicado à outorga e à cobrança da água produzida na exploração petrolífera

Water production is unavoidable during a petrol well s lifetime. The amount of produced water associated with oil varies a lot. It can reach values which account to 50% in volume up to nearly 100%, at the end of the well s economic life. It could be verified that, once the water reaches the productive wells, there must be a management of this produced water. Its destiny is defined after a precise study, after which the best option is chosen between relieving it into the environment, re-injecting it into the producing container or disposing it into non-producing formations. Whichever option is made by the involved professionals, after the necessary analysis, it shall consider, besides the technical and economical aspects, also the alternatives which entail less environmental impact. The purpose of the present research is to conduct a study about the application of the constitutional principle of efficiency on the instruments worked out by the public administration on water management, specifically the water use licence and charging for the use in the management of water resources applicable to water production at the petrol wells. In this attempt, before entering the proper approach of the efficiency of the mentioned instruments, it was necessary not only bring to light the doctrinal perception about the constitutional principle of administrative efficiency, but also make some considerations concerning to the structure of the national water resources management, set by the Federal Constitution (1988) and the federal legislation (9433/97)

Efeitos da qualidade da água de pulverização sobre a eficácia de herbicidas aplicados em pós-emergência

Com o objetivo de estudar o efeito da qualidade da água utilizada na pulverização, sobre a eficácia de herbicidas aplicados em pós-emergência, instalou-se um experimento no ano agrícola 91/92, em área da Fazenda Experimental da Faculdade de Ciências Agrárias e Veterinárias da UNESP, município de Jaboticabal (SP), com 21 tratamentos e três repetições. Os tratamentos foram constituídos pelas combinações de formulações comerciais de glifosate, mistura pronta de glifosate + 2,4D, MSMA e paraquat com as águas deionizada, destilada, limpa (poço profundo), turva 1 (limpa + 2 g.L-1 de solo) e turva 2 (limpa + 10 g.L-1 de solo), além de uma testemunha, na qual não se efetuou a aplicação de herbicidas. Avaliações visuais de controle, geral e por espécie, aos 14, 30 e 45 dias após a aplicação, mostraram que nenhum dos tipos de água utilizados interferiu significativamente na eficiência dos herbicidas, independentemente do produto e da época de avaliação. As quantidades de argila adicionadas às águas denominadas de turva 1 e turva 2 não adsorveram os herbicidas paraquat e glifosate a ponto de prejudicar-lhes a ação. A análise e interpretação dos resultados obtidos, portanto, permitem concluir que o emprego de água turva, oriunda de um reservatório aberto, foi viável para aplicação de alguns herbicidas (glifosate, glifosate + 2,4-D, MSMA e paraquat) em pós-emergência, não influenciando significativamente na sua eficácia .