STATE OF CHARGE BALANCING DROOP CONTROL

This thesis presents a load sharing method applied in a distributed micro grid system. The goal of this method is to balance the state-of-charge (SoC) of each parallel connected battery and make it possible to detect the average SoC of the system by measuring bus voltage for all connected modules. In this method the reference voltage for each battery converter is adjusted by adding a proportional SoC factor. Under such setting the battery with a higher SoC will output more power, whereas the one with lower SoC gives out less. Therefore the higher SoC battery will use its energy faster than the lower ones, and eventually the SoC and output power of each battery will converge. And because the reference voltage is related to SoC status, the information of the average SoC in this system could be shared for all modules by measuring bus voltage. The SoC balancing speed is related to the SoC droop factors. This SoC-based load sharing control system is analyzed in feasibility and stability. Simulations in MATLAB/Simulink are presented, which indicate that this control scheme could balance the battery SoCs as predicted. The observation of SoC sharing through bus voltage was validated in both software simulation and hardware experiments. It could be of use to non-communicated distributed power system in load shedding and power planning.

Load balancing for constraint solving with GPUs

Solving a complex Constraint Satisfaction Problem (CSP) is a computationally hard task which may require a considerable amount of time. Parallelism has been applied successfully to the job and there are already many applications capable of harnessing the parallel power of modern CPUs to speed up the solving process. Current Graphics Processing Units (GPUs), containing from a few hundred to a few thousand cores, possess a level of parallelism that surpasses that of CPUs and there are much less applications capable of solving CSPs on GPUs, leaving space for further improvement. This paper describes work in progress in the solving of CSPs on GPUs, CPUs and other devices, such as Intel Many Integrated Cores (MICs), in parallel. It presents the gains obtained when applying more devices to solve some problems and the main challenges that must be faced when using devices with as different architectures as CPUs and GPUs, with a greater focus on how to effectively achieve good load balancing between such heterogeneous devices.

Components of learning and assessment in linear algebra

Linear algebra provides theory and technology that are the cornerstones of a range of cutting edge mathematical applications, from designing computer games to complex industrial problems, as well as more traditional applications in statistics and mathematical modelling. Once past introductions to matrices and vectors, the challenges of balancing theory, applications and computational work across mathematical and statistical topics and problems are considerable, particularly given the diversity of abilities and interests in typical cohorts. This paper considers two such cohorts in a second level linear algebra course in different years. The course objectives and materials were almost the same, but some changes were made in the assessment package. In addition to considering effects of these changes, the links with achievement in first year courses are analysed, together with achievement in a following computational mathematics course. Some results that may initially appear surprising provide insight into the components of student learning in linear algebra.

Urban sustainability and growth management in south-east Asian city-regions : the case of Kuala Lumpur and Hong Kong

Major South-East Asian city-regions have experienced considerable physical, economic and social transformations during the past three decades. The rapid pace of globalisation and economic restructuring has resulted in these city-regions receiving the full impact of urbanisation pressures. In an attempt to ease these pressures, city-regions such as Bangkok, Seoul, Tokyo, Taipei, Hong Kong, Singapore and Kuala Lumpur have advocate growth management approaches giving particular interest to urban sustainability. These approaches promote efforts to achieve the triple bottom line sustainability by balancing economic and social development, and environmental protection, and putting more emphasis on compact and optimum development of urban forms. This paper evaluates the case of two South-East Asian city-regions, Kuala Lumpur and Hong Kong, and assesses their experiences in managing their urban forms whilst promoting sustainable patterns of urban development. The findings show that sustainable urban development initiatives employing a top down approach has yielded encouraging results in these case study city-regions. However the need for a more concerted effort towards the overall sustainability agenda still remains vital.

Passive control of a bi-ventricular assist device : an experimental and numerical investigation

For the last two decades heart disease has been the highest single cause of death for the human population. With an alarming number of patients requiring heart transplant, and donations not able to satisfy the demand, treatment looks to mechanical alternatives. Rotary Ventricular Assist Devices, VADs, are miniature pumps which can be implanted alongside the heart to assist its pumping function. These constant flow devices are smaller, more efficient and promise a longer operational life than more traditional pulsatile VADs. The development of rotary VADs has focused on single pumps assisting the left ventricle only to supply blood for the body. In many patients however, failure of both ventricles demands that an additional pulsatile device be used to support the failing right ventricle. This condition renders them hospital bound while they wait for an unlikely heart donation. Reported attempts to use two rotary pumps to support both ventricles concurrently have warned of inherent haemodynamic instability. Poor balancing of the pumps’ flow rates quickly leads to vascular congestion increasing the risk of oedema and ventricular ‘suckdown’ occluding the inlet to the pump. This thesis introduces a novel Bi-Ventricular Assist Device (BiVAD) configuration where the pump outputs are passively balanced by vascular pressure. The BiVAD consists of two rotary pumps straddling the mechanical passive controller. Fluctuations in vascular pressure induce small deflections within both pumps adjusting their outputs allowing them to maintain arterial pressure. To optimise the passive controller’s interaction with the circulation, the controller’s dynamic response is optimised with a spring, mass, damper arrangement. This two part study presents a comprehensive assessment of the prototype’s ‘viability’ as a support device. Its ‘viability’ was considered based on its sensitivity to pathogenic haemodynamics and the ability of the passive response to maintain healthy circulation. The first part of the study is an experimental investigation where a prototype device was designed and built, and then tested in a pulsatile mock circulation loop. The BiVAD was subjected to a range of haemodynamic imbalances as well as a dynamic analysis to assess the functionality of the mechanical damper. The second part introduces the development of a numerical program to simulate human circulation supported by the passively controlled BiVAD. Both investigations showed that the prototype was able to mimic the native baroreceptor response. Simulating hypertension, poor flow balancing and subsequent ventricular failure during BiVAD support allowed the passive controller’s response to be assessed. Triggered by the resulting pressure imbalance, the controller responded by passively adjusting the VAD outputs in order to maintain healthy arterial pressures. This baroreceptor-like response demonstrated the inherent stability of the auto regulating BiVAD prototype. Simulating pulmonary hypertension in the more observable numerical model, however, revealed a serious issue with the passive response. The subsequent decrease in venous return into the left heart went unnoticed by the passive controller. Meanwhile the coupled nature of the passive response not only decreased RVAD output to reduce pulmonary arterial pressure, but it also increased LVAD output. Consequently, the LVAD increased fluid evacuation from the left ventricle, LV, and so actually accelerated the onset of LV collapse. It was concluded that despite the inherently stable baroreceptor-like response of the passive controller, its lack of sensitivity to venous return made it unviable in its present configuration. The study revealed a number of other important findings. Perhaps the most significant was that the reduced pulse experienced during constant flow support unbalanced the ratio of effective resistances of both vascular circuits. Even during steady rotary support therefore, the resulting ventricle volume imbalance increased the likelihood of suckdown. Additionally, mechanical damping of the passive controller’s response successfully filtered out pressure fluctuations from residual ventricular function. Finally, the importance of recognising inertial contributions to blood flow in the atria and ventricles in a numerical simulation were highlighted. This thesis documents the first attempt to create a fully auto regulated rotary cardiac assist device. Initial results encourage development of an inlet configuration sensitive to low flow such as collapsible inlet cannulae. Combining this with the existing baroreceptor-like response of the passive controller will render a highly stable passively controlled BiVAD configuration. The prototype controller’s passive interaction with the vasculature is a significant step towards a highly stable new generation of artificial heart.

Australia : The Challenges of Poverty, Pedagogy, and Pathways

A discussion of 2008/2009 developments in Australian educational policy, with specific reference to the adoption of US and UK trends in accountability, testing and school reform.

Dynamics of multi-articular coordination in neurobiological systems

Although previous work in nonlinear dynamics on neurobiological coordination and control has provided valuable insights from studies of single joint movements in humans, researchers have shown increasing interest in coordination of multi-articular actions. Multi-articular movement models have provided valuable insights on neurobiological systems conceptualised as degenerate, adaptive complex systems satisfying the constraints of dynamic environments. In this paper, we overview empirical evidence illustrating the dynamics of adaptive movement behavior in a range of multi-articular actions including kicking, throwing, hitting and balancing. We model the emergence of creativity and the diversity of neurobiological action in the meta-stable region of self organising criticality. We examine the influence on multi-articular actions of decaying and emerging constraints in the context of skill acquisition. We demonstrate how, in this context, transitions between preferred movement patterns exemplify the search for and adaptation of attractor states within the perceptual motor workspace as a function of practice. We conclude by showing how empirical analyses of neurobiological coordination and control have been used to establish a nonlinear pedagogical framework for enhancing acquisition of multi-articular actions.

Choreographing research : supervising the dancing thesis

The dancing doctorate is an interrogative endeavour which can but nurture the art form and forge a beneficial dynamism between those who seek and those who assess the emerging knowledges of dance’. (Vincs, 2009) From 2006-2008 three dance academics from Perth, Brisbane and Melbourne undertook a research project entitled Dancing between Diversity and Consistency: Refining Assessment in Postgraduate Degrees in Dance, funded by the ALTC Priority Projects Program. Although assessment rather than supervision was the primary focus of this research, interviews with 40 examiner/supervisors, 7 research deans and 32 candidates across Australia and across the creative arts, primarily in dance, provide an insight into what might be considered best practice in preparing students for higher research degrees, and the challenges that embodied and experiential knowledges present for supervision. The study also gained the industry perspectives of dance professionals in a series of national forums in 5 cities, based around the value of higher degrees in dance. The qualitative data gathered from these two primary sources was coded and analysed using the NVivo system. Further perspectives were drawn from international consultant and dance researcher Susan Melrose, as well as recent publications in the field. Dance is a young addition to academia and consequently there tends to be a close liaison between the academy and the industry, with a relational fluidity that is both beneficial and problematic. This partially explains why dance research higher degrees are predominantly practice-led (or multi-modal, referring to those theses where practice comprises the substantial examinable component). As a physical, embodied art form, dance engages with the contested territory of legitimising alternative forms of knowledge that do not sit comfortably with accepted norms of research. In supporting research students engaged with dance practice, supervisors traverse the tricky terrain of balancing university academic requirements with studies that are emergent, not only in the practice and attendant theory but in their methodologies and open-ended outcomes; and in an art form in which originality and new knowledge also arises from collaborative creative processes. Formal supervisor accreditation through training is now mandatory in most Australian universities, but it tends to be generic and not address supervisory specificity. This paper offers the kind of alternative proposed by Edwards (2002) that improving postgraduate supervision will be effective if supervisors are empowered to generate their own standards and share best practice; in this case, in ways appropriate to the needs of their discipline and alternative modes of thesis presentation. In order to frame the qualities and processes conducive to this goal, this paper will draw on both the experiences of interviewees and on philosophical premises which underpin the research findings of our study. These include the ongoing challenge of dissolving the binary oppositions of theory and practice, especially in creative arts practice where theory resides in and emerges from the doing as much as in articulating reflection about the doing through what Melrose (2003) terms ‘mixed mode disciplinary practices’. In guiding practitioners through research higher degrees, how do supervisors deal with not only different forms of knowledge but indeed differing modes of knowledge? How can they navigate tensions that occur between the ‘incompatible competencies’ (Candlin, 2000) of the ‘spectating’ academic experts with their ‘irrepressible drive ... to inscribe, interpret, and hence to practise temporal closure’, and practitioner experts who create emergent works of ‘residual unfinishedness’ (Melrose 2006) which are not only embodied but ephemeral, as in the case of live performance?

Rigour versus Relevance Revisited : Evidence from IS Conference Reviewing Practice

A commonly held belief in the IS discipline is that rigour and relevance are contrary to each other and that addressing both is virtually impossible. It is also believed widely that the editorial practices of our premier conferences and journals over-emphasise rigour on the cost of relevance. However, while these two topics have been filled with numerous subjective discussions, more solid evidence into the true relationship between rigour and relevance and the impact of conference editors on this relationship is still outstanding. This paper contributes to this debate by deriving empirical evidence from a comprehensive and detailed analysis of the characteristics of the submissions and the reviewing practices of three recent IS conferences. It provides first insights into the actual relationship between rigour and relevance and into the role conference chairs play in balancing rigour and relevance. Besides the outcomes that the current set of evaluation criteria does not provide a straight forward proxy for relevance to practitioners, the paper offers two main contributions. First, empirical insights are provided that rigour and relevance do in fact not have to be mutually exclusive. Second, the editorial practices at conferences are skewed towards rigorous papers rather than relevant papers.

Enabling authentic collaborative education in an online environment : the QUT Virtual Law Placement

This paper explores an innovative model for work-integrated learning using a virtual paradigm – The Virtual Law Placement Unit at Queensland University of Technology (QUT) Australia. It builds upon the conceptual model previously explored at WACE 2007 and provides an account of the lessons learned from the pilot offering of the unit which was conducted and evaluated in 2008. ----- The Virtual Placement Unit offers students the opportunity to complete an authentic workplace task under the guidance of a real-life workplace supervisor, where student-student communication and student-supervisor communication is all conducted virtually (and potentially asynchronously) to create an engaging but flexible learning environment using a combination of Blackboard and SharePoint technologies. This virtual experience is pioneering in the sense that it enables law students to access an unprecedented range of law graduate destination workplaces and projects, including international and social justice placements, absent the constraints traditionally associated with arranging physical placements. ----- All aspects of this unit have been designed in conjunction with community partners with a view to balancing student learning objectives with community needs through co-operative education. This paper will also explore how the implementation of the project is serving to strengthen those partnerships with the wider community, simultaneously addressing the community engagement agenda of the University and enabling students to engage meaningfully with local, national and international community partners in the real world of work.

A new family of multi-output DC-DC converter topologies to supply an asymmetrical four-level diode-clamped inverter

Purpose Multi-level diode-clamped inverters have the challenge of capacitor voltage balancing when the number of DC-link capacitors is three or more. On the other hand, asymmetrical DC-link voltage sources have been applied to increase the number of voltage levels without increasing the number of switches. The purpose of this paper is to show that an appropriate multi-output DC-DC converter can resolve the problem of capacitor voltage balancing and utilize the asymmetrical DC-link voltages advantages. Design/methodology/approach A family of multi-output DC-DC converters is presented in this paper. The application of these converters is to convert the output voltage of a photovoltaic (PV) panel to regulate DC-link voltages of an asymmetrical four-level diode-clamped inverter utilized for domestic applications. To verify the versatility of the presented topology, simulations have been directed for different situations and results are presented. Some related experiments have been developed to examine the capabilities of the proposed converters. Findings The three-output voltage-sharing converters presented in this paper have been mathematically analysed and proven to be appropriate to improve the quality of the residential application of PV by means of four-level asymmetrical diode-clamped inverter supplying highly resistive loads. Originality/value This paper shows that an appropriate multi-output DC-DC converter can resolve the problem of capacitor voltage balancing and utilize the asymmetrical DC-link voltages advantages and that there is a possibility of operation at high-modulation index despite reference voltage magnitude and power factor variations.

Examining accountability dimensions in state-owned enterprises

This paper examines accountability in the context of New Zealand's state-owned enterprises (SOEs), and considers an accountability framework which extends beyond traditional (upward and outward) dimensions. While traditional accountability dimensions are clearly detailed in the legislation, less clear are the dilemmas and contradictions faced by SOEs, balancing multiple interests, and at times, conflicting objectives. These issues are explored through interviews conducted in two phases over a two year period with senior executives from 12 of the then 17 SOEs operating in New Zealand. Findings reveal a number of dimensions of accountability that extend beyond current conceptualisations of accountability in the public sector, often including multiple directions of accountability. Implications suggest the need for a more explicit framework of accountability relevant to the SOE context, which may serve useful in identifying potential pathways to conflict mitigation.

Venture creation and resource processes : using Bricolage sustainability ventures

Principal Topic: Resource decisions are critical to the venture creation process, which has important subsequent impacts on venture creation and performance (Boeker, 1989). Most entrepreneurs however, suffer substantial resource constraints in venture creation and during venture growth (Shepherd et al., 2000). Little is known about how high potential, sustainability ventures (the ventures of interest in this research), despite resource constraints, achieve continued venture persistence and venture success. One promising theory that explicitly links to resource constraints is a concept developed by Levi Strauss (1967) termed bricolage. Bricolage aligns with notions of resourcefulness: using what's on hand, through making do, and recombining resources for new or novel purposes (Baker & Nelson 2005). To the best of our knowledge, previous studies have not systematically investigated internal and external constraints, their combinations, and subsequent bricolage patterns. The majority of bricolage literature focuses on external environmental constraints (e.g. Wieck 1989; Baker & Nelson 2005), thereby paying less attention to in evaluating internal constraints (e.g. skills and capabilities) or constraint combinations. In this paper we focus on ventures that typically face resource-poor environments. High potential, nascent and young sustainability ventures are often created and developed with resource constraints and in some cases, have greater resource requirements owing to higher levels of technical sophistication of their products (Rothaermel & Deeds 2006). These ventures usually have high aspirations and potential for growth who ''seeks to meet the needs and aspirations without compromising the ability to meet those of the future'' (Brundtland Commission 1983). High potential ventures are increasingly attributed with a central role in the development of innovation, and employment in developed economies (Acs 2008). Further, increasing awareness of environmental and sustainability issues has fostered demand for business processes that reduce detrimental environmental impacts of global development (Dean & McMullen 2007) and more environmentally sensitive products and services: representing an opportunity for the development of ventures that seek to satisfy this demand through entrepreneurial action. These ventures may choose to ''make do'' with existing resources in developing resource combinations that produce the least impact on the environment. The continuous conflict between the greater requirements for resources and limited resource availability in high potential sustainable ventures, with the added complexity of balancing this with an uncompromising focus on using ''what's on hand'' to lessen environment impacts may make bricolage behaviours critical for these ventures. Research into bricolage behaviour is however, the exception rather than the rule (Cunha 2005). More research is therefore needed to further develop and extend this emerging concept, especially in the context of sustainability ventures who are committed to personal and social goals of resourcefulness. To date, however, bricolage has not been studied specifically among high potential sustainable ventures. This research seeks to develop an in depth understanding of the impact of internal and external constraints and their combinations on the mechanisms employed in bricolage behaviours in differing dynamic environments. The following research question was developed to investigate this: How do internal, external resource constraints (or their combinations) impact bricolage resource decisions in high potential sustainability ventures? ---------- Methodology/Key Propositions: 6 case studies will be developed utilizing survey data from the Comprehensive Australian Study of Entrepreneurial Emergence (CAUSEE) large-scale longitudinal study of new venture start-ups in Australia. Prior to commencing case studies, 6 scoping interviews were conducted with key stakeholders including industry members, established businesses and government to ensure practical relevance in case development. The venture is considered the unit of analysis with the key informant being the entrepreneur and other management team members where appropriate. Triangulation techniques are used in this research including semi-structured interviews, survey data, onsite visits and secondary documentation website analysis, resumes, and business plans. These 6 sustainability ventures have been selected based on different environmental dynamism conditions including a traditionally mature market (building industry) and a more dynamic, evolving industry (renewable energy/solar ventures). In evaluating multidisciplinary literature, we expect the following external constraints are critical including: technology constraints (seen through lock-in of incumbents existing technology), institutional regulation and standards, access to markets, knowledge and training to nascent and young venture bricolage processes. The case studies will investigate internal constraints including resource fungability, resource combination capabilities, translating complex science/engineering knowledge into salient, valuable market propositions, i.e. appropriate market outcomes, and leveraging relationships may further influence bricolage decisions. ---------- Results and Implications: Intended ventures have been identified within the CAUSEE sample and have agreed to participate and secondary data collection for triangulation purposes has already commenced. Data collection of the case studies commenced 27th of May 2009. Analysis is expected to be completed finalised by 25th September 2009. This paper will report on the pattern of resource constraints and its impact on bricolage behaviours: its subsequent impact on resource deployment within venture creation and venture growth. As such, this research extends the theory of bricolage through the systematic analysis of constraints on resource management processes in sustainability ventures. For practice, this research may assist in providing a better understanding of the resource requirements and processes needed for continued venture persistence and growth in sustainability ventures. In these times of economic uncertainty, a better understanding of the influence on constraints and bricolage: the interplay of behaviours, processes and outcomes may enable greater venture continuance and success.

Australia experiments with 'experimental use' exemption

Lawmakers are asking whether Australian researchers need an express 'experimental use' defense against patent infringement. The overriding policy for establishing a patent system is indisputably the promotion of innovation. According to traditional intellectual property pedagogy, the incentive to innovate flows from the reward afforded to the inventor. A balancing policy is that the patentee must fully disclose the invention to help minimize the risks of duplication and provides a basis for improvements by further research.Where there is uncertainty as to how these competing policy limbs are balanced and whether a patentee can exclude others from experimenting on a patented invention, the uncertain legal environment disadvantages both the patentee and researcher. Different jurisdictions have treated the experimental use question quite differently with varied results for the researcher. The biotechnology industry is evolving at an unprecedented pace and the law will as is always the case, lag behind in its usual cautious fashion. The Australian law may finally catch up to researchers' concerns.