CMOS IMPLEMENTATION OF A SYSTOLIC MULTI-BIT CONVOLVER CHIP.

The implementation of a multi-bit convolver chip based on a systolic array is described. The convolver is fabricated on a 7mm multiplied by 8mm CMOS chip and operates on 8-bit serial data and coefficient words. It has a length of 17 stages, and this is cascadable. The circuit can be clocked at more than 20 MHz giving a data throughput rate of greater than 1 Mword/s. Details of important implementation decisions and a summary of chip characteristics are given together with the advantages which the systolic approach has afforded to the design process.

Programmable high-performance IIR filter chip

The paper presents a state-of-the-art commercial demonstrator chip for infinite impulse response (IIR) filtering. The programmable IIR filter chip contains eight multiplier/accumulators that can be configured in one of five different modes to implement up to a 16th-order IIR filter. The multiply-accumulate block is based on a highly regular systolic array architecture and uses a redundant number system to overcome problems of pipelining in the feedback loop. The chip has been designed using the GEC Plessey Semiconductors CLA 78000 series gate array, operates on 16-bit two's complement data and has a clock speed of 30 MHz. Issues such as overflow detection and design for testability have also been addressed and are described.

NDT to identify biological damage in wood

Nondestructive techniques are widely used to assess existing timber structures. The models proposed for these methods are usually performed in the laboratory using small clear wood specimens. But in real situations many anomalies, defects and biological damage are found in wood. In these cases the existing models only indicate that the values are outside normality without providing any other information. To solve this problem, a study of non-destructive probing methods for wood was performed, testing the behaviour of four different techniques (penetration resistance, pullout resistance, drill resistance and chip drill extraction) on wood samples with different biological damage, simulating an in-situ test. The wood samples were obtained from existing Spanish timber structures with biotic damage caused by borer insects, termites, brown rot and white rot. The study concludes that all of the methods offer more or less detailed information about the degree of deterioration of wood, but that the first two methods (penetration and pullout resistance) cannot distinguish between pathologies. On the other hand, drill resistance and chip drill extraction make it possible to differentiate pathologies and even to identify species or damage location. Finally, the techniques used were compared to characterize their advantages and disadvantages.

Particle number and mass emission factors from combustion of wood samples collected from Queensland forest

Knowledge of particle emission characteristics associated with forest fires and in general, biomass burning, is becoming increasingly important due to the impact of these emissions on human health. Of particular importance is developing a better understanding of the size distribution of particles generated from forest combustion under different environmental conditions, as well as provision of emission factors for different particle size ranges. This study was aimed at quantifying particle emission factors from four types of wood found in South East Queensland forests: Spotted Gum (Corymbia citriodora), Red Gum (Eucalypt tereticornis), Blood Gum (Eucalypt intermedia), and Iron bark (Eucalypt decorticans); under controlled laboratory conditions. The experimental set up included a modified commercial stove connected to a dilution system designed for the conditions of the study. Measurements of particle number size distribution and concentration resulting from the burning of woods with a relatively homogenous moisture content (in the range of 15 to 26 %) and for different rates of burning were performed using a TSI Scanning Mobility Particle Sizer (SMPS) in the size range from 10 to 600 nm and a TSI Dust Trak for PM2.5. The results of the study in terms of the relationship between particle number size distribution and different condition of burning for different species show that particle number emission factors and PM2.5 mass emission factors depend on the type of wood and the burning rate; fast burning or slow burning. The average particle number emission factors for fast burning conditions are in the range of 3.3 x 1015 to 5.7 x 1015 particles/kg, and for PM2.5 are in the range of 139 to 217 mg/kg.

Theoretical analysis of serrated chip formation based on ideal models in high speed cutting

In this paper, two ideal formation models of serrated chips, the symmetric formation model and the unilateral right-angle formation model, have been established for the first time. Based on the ideal models and related adiabatic shear theory of serrated chip formation, the theoretical relationship among average tooth pitch, average tooth height and chip thickness are obtained. Further, the theoretical relation of the passivation coefficient of chip's sawtooth and the chip thickness compression ratio is deduced as well. The comparison between these theoretical prediction curves and experimental data shows good agreement, which well validates the robustness of the ideal chip formation models and the correctness of the theoretical deducing analysis. The proposed ideal models may have provided a simple but effective theoretical basis for succeeding research on serrated chip morphology. Finally, the influences of most principal cutting factors on serrated chip formation are discussed on the basis of a series of finite element simulation results for practical advices of controlling serrated chips in engineering application.

Seeing the Wood for the Trees: A Critical Evaluation of Methods to Estimate the Parameters of Stochastic Differential Equations

Maximum-likelihood estimates of the parameters of stochastic differential equations are consistent and asymptotically efficient, but unfortunately difficult to obtain if a closed-form expression for the transitional probability density function of the process is not available. As a result, a large number of competing estimation procedures have been proposed. This article provides a critical evaluation of the various estimation techniques. Special attention is given to the ease of implementation and comparative performance of the procedures when estimating the parameters of the Cox–Ingersoll–Ross and Ornstein–Uhlenbeck equations respectively.

My mother is water, my father is wood

'my mother is water, my father is wood' was an installation comprised of two large cork discs mounted on the gallery floor and wall, overlaid with images of photographic and archival research evidence, and a turned wood sculptural object. It also included a short video work on a miniature screen embedded in the upright disc. The work explored the language of natural elements and the structure of genealogical research to discuss the Scandinavian history of Queensland and my own family. The work was selected by the directors of LEVEL ARI in Brisbane for inclusion in their 2011 exhibitions program.

The Wood Royal Commission : a case study in the slippery slope from unethical conduct to criminal acts

Over the last two and a half decades, corruption in the police service in Australia has come under increased official and public scrutiny. Numerous scandals involving police officers has caused concerned about the integrity and ethics within the Police Service. This paper examines the Wood Royal Commission, specifically looking at testimony from Trevor Haken. This paper provides insights into the nature of police corruption as well as the process or ‘slippery slope’ corrupt officers go through. This paper also contributed to the existing literature by providing knowledge into the types of corruption used by police officers in real-life situations, and deepening understanding of how corruption emerges and why. It specifically confirms the literature on slippery slope arguments about police corruption and the role of trust in building a corrupt career. The paper contributes to the existing literature by providing insights into the nature of corruption used by police officers in real-life situations, and deepens the understanding of the process of corruption. The findings also contribute to our understanding that corruption is not just an individual incident but rather a result of reoccurring incidents that are generated by the nature of work, organizational structure and society in relation to corruption.