Investigations of secondary organic aerosol formation in laboratory chambers

Secondary organic aerosol (SOA) is produced in the atmosphere by oxidation of volatile organic compounds. Laboratory chambers are used understand the formation mechanisms and evolution of SOA formed under controlled conditions. This thesis presents studies of SOA formed from anthropogenic and biogenic precursors and discusses the effects of chamber walls on suspended vapors and particles.

During a chamber experiment, suspended vapors and particles can interact with the chamber walls. Particle wall loss is relatively well-understood, but vapor wall losses have received little study. Vapor wall loss of 2,3-epoxy-1,4-butanediol (BEPOX) and glyoxal was identified, quantified, and found to depend on chamber age and relative humidity.

Particles reside in the atmosphere for a week or more and can evolve chemically during that time period, a process termed aging. Simulating aging in laboratory chambers has proven to be challenging. A protocol was developed to extend the duration of a chamber experiment to 36 h of oxidation and was used to evaluate aging of SOA produced from m-xylene. Total SOA mass concentration increased and then decreased with increasing photooxidation suggesting a transition from functionalization to fragmentation chemistry driven by photochemical processes. SOA oxidation, measured as the bulk particle elemental oxygen-to-carbon ratio and fraction of organic mass at m/z 44, increased continuously starting after 5 h of photooxidation.

The physical state and chemical composition of an organic aerosol affect the mixing of aerosol components and its interactions with condensing species. A laboratory chamber protocol was developed to evaluate the mixing of SOA produced sequentially from two different sources by heating the chamber to induce particle evaporation. Using this protocol, SOA produced from toluene was found to be less volatile than that produced from a-pinene. When the two types of SOA were formed sequentially, the evaporation behavior most closely represented that of SOA from the second parent hydrocarbon, suggesting that the structure of the mixed SOA particles resembles a core of SOA from the first precursor coated by a layer of SOA from the second precursor, indicative of limiting mixing.

Progress in the understanding of Ni silicide formation for advanced MOS structures

Metallic silicides have been used as contact materials on source/drain and gate in metal-oxide semiconductor (MOS) structure for 40 years. Since the 65 nm technology node, NiSi is the preferred material for contact in microelectronic due to low resistivity, low thermal budget, and low Si consumption. Ni(Pt)Si with 10 at.% Pt is currently employed in recent technologies since Pt allows to stabilize NiSi at high temperature. The presence of Pt and the very low thickness (<10 nm) needed for the device contacts bring new concerns for actual devices. In this work, in situ techniques [X-ray diffraction (XRD), X-ray reflectivity (XRR), sheet resistance, differential scanning calorimetry (DSC)] were combined with atom probe tomography (APT) to study the formation mechanisms as well as the redistribution of dopants and alloy elements (Pt, Pd.) during the silicide formation. Phenomena like nucleation, lateral growth, interfacial reaction, diffusion, precipitation, and transient phase formation are investigated. The effect of alloy elements (Pt, Pd.) and dopants (As, B.) as well as stress and defects induced by the confinement in devices on the silicide formation mechanism and alloying element redistribution is examined. In particular APT has been performed for the three-dimensional (3D) analysis of MOSFET at the atomic scale. The advances in the understanding of the mechanisms of formation and redistribution are discussed. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The influencing factors on the macroporous formation in polymer films by water droplet templating

Regular micrometer-size porous polystyrene film is prepared by water droplet templating, i.e. breath figures are stabilized by the polymer in solution and thermocapillary flow arranges them into ordered packing. The influences of polystyrene molecular weight, solvent properties, and the relative humidity of atmosphere on the pattern formation and hole sizes are investigated. Two different kinds of hole packing fashion are also observed and their formation mechanisms are discussed.

Pattern formation in a confined polymer film induced by a temperature gradient

We have studied a morphological instability of a double layer comprising the polymer film and air gap confined between the two plates set to different temperatures. The temperature gradient across the double layer causes the breakup of the polymer film into well-defined columnar, striped or spiral structures spanning the two plates. The pattern formation mechanisms have been discussed. The formed patterns can be transferred to produce PDMS stamp, a key element of soft lithography for future microfabrication.

Ordered pattern formation from dewetting of polymer thin film with surface disturbance by capillary force lithography

The dewetting process of thin polystyrene (PS) film with built-in ordered disturbance by capillary force lithography (CFL) has. been investigated in situ by AFM. Two different phenomena are observed depending on the excess surface energy (DeltaF(gamma)) of the system. When DeltaF(gamma) is less than a certain critical value (i.e., the disturbance amplitude is under a critical value), the PS film would be flattened and become stable finally by heating above T-g. While, if the size of the disturbance amplitude is larger than the critical value, ordered PS liquid droplets form by further dewetting. The pattern formation mechanisms and influencing factors have been discussed in detail.

Pattern formation in polymer films under the mask

This paper presents a straightforward method for patterning thin films of polymers, i.e. a prepatterned mask is used to induce self-assembly of polymers and the resulting pattern is the same as the lateral structures in the mask on a submicrometre length scale, The patterns can be formed at above T-g + 30 degreesC in a short time and the external electric field is not crucial. Electrostatic force is assumed to be the driving force for the pattern transfer. Viscous fingering and novel stress-relief lateral morphology induced under the featureless mask are also observed and the formation mechanisms are discussed.

Formation of regular hole pattern in polymer films

Ordered macroporous materials recently have attracted much attention. A method that utilizes the condensation of monodisperse water droplets on a polymer solution is proposed for the preparation of honeycomb microporous films. Our results show that it is a general method that can be used for patterning a wide range of polymers. The presence of water vapor and polymer is necessary for the formation of regular holes in films. The formation of hexagonal packing instead of other kinds of packing takes place because the hexagonal packing has the lowest free energy. The formation mechanisms of regular hole pattern and imperfections in the hexagonal packing are proposed.

Simulating the formation of secondary organic aerosol from the photooxidation of aromatic hydrocarbons

The formation and composition of secondary organic aerosol (SOA) from the photooxidation of benzene, p-xylene, and 1,3,5-trimethylbenzene has been simulated using the Master Chemical Mechanism version 3.1 (MCM v3.1) coupled to a representation of the transfer of organic material from the gas to particle phase. The combined mechanism was tested against data obtained from a series of experiments conducted at the European Photoreactor (EUPHORE) outdoor smog chamber in Valencia, Spain. Simulated aerosol mass concentrations compared reasonably well with the measured SOA data only after absorptive partitioning coefficients were increased by a factor of between 5 and 30. The requirement of such scaling was interpreted in terms of the occurrence of unaccounted-for association reactions in the condensed organic phase leading to the production of relatively more nonvolatile species. Comparisons were made between the relative aerosol forming efficiencies of benzene, toluene, p-xylene, and 1,3,5-trimethylbenzene, and differences in the OH-initiated degradation mechanisms of these aromatic hydrocarbons. A strong, nonlinear relationship was observed between measured (reference) yields of SOA and (proportional) yields of unsaturated dicarbonyl aldehyde species resulting from ring-fragmenting pathways. This observation, and the results of the simulations, is strongly suggestive of the involvement of reactive aldehyde species in association reactions occurring in the aerosol phase, thus promoting SOA formation and growth. The effect of NO, concentrations on SOA formation efficiencies (and formation mechanisms) is discussed.

Multifunctional acid formation from the gas-phase ozonolysis of beta-pinene

The gas-phase ozonolysis of beta-pinene was studied in static chamber experiments, using gas chromatography coupled to mass spectrometric and flame ionisation detection to separate and detect products. A range of multifunctional organic acids-including pinic acid, norpinic acid, pinalic-3- acid, pinalic-4-acid, norpinalic acid and OH-pinalic acid-were identified in the condensed phase after derivatisation. Formation yields for these products under systematically varying reaction conditions (by adding different OH radical scavengers and Criegee intermediate scavengers) were investigated and compared with those observed from alpha-pinene ozonolysis, allowing detailed information on product formation mechanisms to be elucidated. In addition, branching ratios for the initial steps of the reaction were inferred from quantitative measurements of primary carbonyl formation. Atmospheric implications of this work are discussed.

Potato glycoalkaloids: formation and strategies for mitigation

With the increasing production and consumption of potato and its products, glycoalkaloid (GA) formation and toxicity are likely to become an important focus for food safety researchers and public health agencies. Not only the presence of GA, particularly in the form of a-solanine and a-chaconine, but also the changes occurring as a result of various post-harvest handling practices and storage, are critical issues influencing the quality of stored potatoes. Studies on various factors (pre-harvest, during harvest anal post-harvest) affecting GA have been carried out from time to time, but it is difficult to compare the results of one study with another due to wide variation in the parameters chosen. This review aims to develop a clear understanding of these issues. Published information on the types of GA, their effects on health, their typical concentrations in potatoes, their formation mechanisms, and how their levels can be controlled by following appropriate post harvest practices and storage regimes are critically analysed. The levels of GA in potato can be controlled effectively by adopting appropriate post-harvest practices. Further studies are necessary, however, to investigate best practices, which either check completely or retard substantially their formation. (C) 2008 Society of Chemical Industry.

Engineering of small-molecule gels based on the thermodynamics and kinetics of fiber formation

In this chapter, we will give an overview of our work on manipulating the micro/nano structure and macroscopic properties of SMGs. Firstly, it will cover the analysis of the thermodynamics of fiber formation in SMGs and the classification and characterization of the topological and micro/nano structures of fiber networks, followed by the analysis of the formation kinetics of these networks. The criteria of engineering of the SMGs will be summarized according to the latest understanding of the formation mechanisms of fiber networks. On the basis of this understanding, approaches that have been developed to engineer the micro/nanometer structures and macroscopic properties of typical SMGs will be presented.

Word-formation and the translation of Marvel comic book charactonyms

This article analyzes the solutions given in Spanish translations to the morphological creativity shown in the names of Marvel comic book characters. The English versions almost invariably provide a full description of the hero (or villain) by means of a wide variety of word-formation mechanisms leading to highly expressive charactonyms. Indeed, examples shall be listed of names of comic book heroes created through compounding, derivation, including prefixation or suffixation (both classical and Anglo-Saxon but also from other origins), lexical blending, abbreviation, clipping, onomatopoeia, and borrowings from Spanish or from other languages. Early translations into Spanish seemed to be slightly less expressive than the original, even when the same word-formation mechanism was used, usually due to either problems of transparency mainly in some of the word parts or to translation constraints. In later periods, a number of factors, including the influence from other media featuring the same characters and the general trend towards globalization through English, have led translators to choose repetition as the most frequent strategy, which has almost eliminated the creative power of wordformation mechanisms in Spanish and their ability to convey the stylistic effects found in the English versions.

Microstructures layering, mechanisms in the middle waters of the Persian Gulf

Layered structures, known as micro structures in marine environments are common features of which their formation mechanisms are first reviewed. Some methods of measuring such features based on the measurements and theories are presented for the Persian Gulf. This includes determination of layers with temperature inversion (TI) associated with double diffusive convection (DDC). The relevant associated parameters are estimated from ROPME CTD data for late winter and early summer of 1992. Only in certain parts temperature inversion and DDC are observed which seem to produce layered structures. Observations show that the places with TI and DDC are mainly confined to the frontal regions where the water entering the Persian Gulf and water exiting it meet, nearly along the axis of the Gulf. TI and DDC is mainly observer in the northern bound of the front. Typical density ratio for regions with TI and DDC is 0.7 to 0.2 and the mean depth is at about 37 ± 3 m for the Persian Gulf. TI and DDC are also found in the outflow from the Persian Gulf to the Oman Gulf which is found to be at a depth of about 250 m. Horizontal addiction and reduction of solar heating seem to be the main reasons in producing layers with TI and DDC. It is also found that the regime of DDC in the Persian Gulf is more diffusive and the flow associated with intrusion layers with TI is non-isopycnal (more unstable). However for the Oman sea both diffusive and finger regime are observed and the flow is inferred to be isopycnal (more stable statically). Typical heat and salt fluxes due to DDC are found to be 6 W/m2 and 0.36 W/m2 respectively. Effective salinity diffusivity, Ks and heat diffusivity, Kr have been estimated for the places with DDC in the Persian Gulf and Oman Gulf (Ks=1.1 *10-7 m2/s, KT= 1.88*10-6 m2/s). Their values are within the values obtained by others. The buoyancy frequency for the Persian Gulf with typical mean value of 0.05s-1 is much higher than these of the free Oceans. Such large values of N (typically 0.05 s-1) indicate that processes such as tide can produce strong internal waves which may be another factor in producing layered structures. This requires separate study.

Quantification of the relationship between Fuser Roller Temperature and Laser Printer Emissions

Recently published studies not only demonstrated that laser printers are often significant sources of ultrafine particles, but they also shed light on particle formation mechanisms. While the role of fuser roller temperature as a factor affecting particle formation rate has been postulated, its impact has never been quantified. To address this gap in knowledge, this study measured emissions from 30 laser printers in chamber using a standardized printing sequence, as well as monitoring fuser roller temperature. Based on a simplified mass balance equation, the average emission rates of particle number, PM2.5 and O3 were calculated. The results showed that: almost all printers were found to be high particle number emitters (i.e. > 1.01×1010 particles/min); colour printing generated more PM2.5 than monochrome printing; and all printers generated significant amounts of O3. Particle number emissions varied significantly during printing and followed the cycle of fuser roller temperature variation, which points to temperature being the strongest factor controlling emissions. For two sub-groups of printers using the same technology (heating lamps), systematic positive correlations, in the form of a power law, were found between average particle number emission rate and average roller temperature. Other factors, such as fuser material and structure, are also thought to play a role, since no such correlation was found for the remaining two sub-groups of printers using heating lamps, or for the printers using heating strips. In addition, O3 and total PM2.5 were not found to be statistically correlated with fuser temperature.

Exposure to particles from laser printers operating within office workplaces

While recent research has provided valuable information as to the composition of laser printer particles, their formation mechanisms, and explained why some printers are emitters whilst others are low emitters, fundamental questions relating to the potential exposure of office workers remained unanswered. In particular, (i) what impact does the operation of laser printers have on the background particle number concentration (PNC) of an office environment over the duration of a typical working day?; (ii) what is the airborne particle exposure to office workers in the vicinity of laser printers; (iii) what influence does the office ventilation have upon the transport and concentration of particles?; (iv) is there a need to control the generation of, and/or transport of particles arising from the operation of laser printers within an office environment?; (v) what instrumentation and methodology is relevant for characterising such particles within an office location? We present experimental evidence on printer temporal and spatial PNC during the operation of 107 laser printers within open plan offices of five buildings. We show for the first time that the eight-hour time-weighted average printer particle exposure is significantly less than the eight-hour time-weighted local background particle exposure, but that peak printer particle exposure can be greater than two orders of magnitude higher than local background particle exposure. The particle size range is predominantly ultrafine (< 100nm diameter). In addition we have established that office workers are constantly exposed to non-printer derived particle concentrations, with up to an order of magnitude difference in such exposure amongst offices, and propose that such exposure be controlled along with exposure to printer derived particles. We also propose, for the first time, that peak particle reference values be calculated for each office area analogous to the criteria used in Australia and elsewhere for evaluating exposure excursion above occupational hazardous chemical exposure standards. A universal peak particle reference value of 2.0 x 104 particles cm-3 has been proposed.