Spontane Strukturbildung in Mehrschichtsystemen unter Verwendung Molekularer Gläser

Den Schwerpunkt dieser Dissertation bildet zum einen die Entwicklung eines theoretischen Modells zur Beschreibung des Strukturbildungsprozesses in organisch/anorganischen Doppelschichtsystemen und zum anderen die Untersuchung der Übertragbarkeit dieser theoretisch gewonnenen Ergebnisse auf reale Systeme. Hierzu dienen systematische experimentelle Untersuchungen dieses Phänomens an einem Testsystem. Der Bereich der selbstorganisierenden Systeme ist von hohem wissenschaftlichen Interesse, erlaubt er doch die Realisierung von Strukturen, die nicht den Begrenzungen heutiger Techniken unterliegen, wie etwa der Beugung bei lithographischen Verfahren. Darüber hinaus liefert ein vertieftes Verständnis des Strukturbildungsprozesses auch eine Möglichkeit, im Falle entsprechender technischer Anwendungen Instabilitäten innerhalb der Schichtsysteme zu verhindern und somit einer Degradation der Bauteile entgegenzuwirken. Im theoretischen Teil der Arbeit konnte ein Modell im Rahmen der klassischen Elastizitätstheorie entwickelt werden, mit dessen Hilfe sich die Entstehung der Strukturen in Doppelschichtsystemen verstehen läßt. Der hier gefundene funktionale Zusammenhang zwischen der Periode der Strukturen und dem Verhältnis der Schichtdicken von organischer und anorganischer Schicht, wird durch die experimentellen Ergebnisse sehr gut bestätigt. Die Ergebnisse zeigen, daß es technologisch möglich ist, über die Vorgabe der Schichtdicke in einem Materialsystem die Periodizität der entstehenden Strukturen vorzugeben. Darüber hinaus liefert das vorgestellte Modell eine Stabilitätsbedingung für die Schichtsysteme, die es ermöglicht, zu jedem Zeitpunkt die dominierende Mode zu identifizieren. Ein Schwerpunkt der experimentellen Untersuchungen dieser Arbeit liegt auf der Strukturbildung innerhalb der Schichtsysteme. Das Testsystem wurde durch Aufbringen einer organischen Schicht - eines sog. Molekularen Glases - auf ein Glassubstrat realisiert, als Deckschicht diente eine Siliziumnitrid-Schicht. Es wurden Proben mit variierenden Schichtdicken kontrolliert erwärmt. Sobald die Temperatur des Schichtsystems in der Größenordnung der Glasübergangstemperatur des jeweiligen organischen Materials lag, fand spontan eine Strukturbildung auf Grund einer Spannungsrelaxation statt. Es ließen sich durch die Wahl einer entsprechenden Heizquelle unterschiedliche Strukturen realisieren. Bei Verwendung eines gepulsten Lasers, also einer kreisförmigen Wärmequelle, ordneten sich die Strukturen konzentrisch an, wohingegen sich ihre Ausrichtung bei Verwendung einer flächenhaften Heizplatte statistisch verteilte. Auffällig bei allen Strukturen war eine starke Modulation der Oberfläche. Ferner konnte in der Arbeit gezeigt werden, daß sich durch eine gezielte Veränderung der Spannungsverteilung innerhalb der Schichtsysteme die Ausrichtung der Strukturen (gezielt) manipulieren ließen. Unabhängig davon erlaubte die Variation der Schichtdicken die Realisierung von Strukturen mit einer Periodizität im Bereich von einigen µm bis hinunter zu etwa 200 nm. Die Kontrolle über die Ausrichtung und die Periodizität ist Grundvoraussetzung für eine zukünftige technologische Nutzung des Effektes zur kontrollierten Herstellung von Mikro- bzw. Nanostrukturen. Darüber hinaus konnte ein zunächst von der Strukturbildung unabhängiges Konzept eines aktiven Sensors für die optische Raster-Nahfeld-Mikroskopie vorgestellt werden, das das oben beschriebene System, bestehend aus einem fluoreszierenden Molekularen Glas und einer Siliziumnitrid-Deckschicht, verwendet. Erste theoretische und experimentelle Ergebnisse zeigen das technologische Potential dieses Sensortyps.

Magnetische Kopplungen in magneto-optischen Speicherschichten

Im Rahmen dieser Arbeit wurden magneto-optische Speicherschichten und ihre Kopplungen untereinander untersucht. Hierzu wurden zum Einen die für die magneto-optische Speichertechnologie "klassischen" Schichten aus RE/TM-Legierungen verwendet, zum Anderen aber auch erfolgreich Granate integriert, die bisher nicht in diesem Anwendungsgebiet verwendet wurden. Einleitend werden die magneto-optischen Verfahren, die resultierenden Anforderungen an die dünnen Schichten und die entsprechenden physikalischen Grundlagen diskutiert. Außerdem wird auf das Hochfrequenz-Sputtern von RE/TM-Legierungen eingegangen und die verwendeten magneto-optischen Messverfahren werden erläutert [Kap. 2 & 3]. Die Untersuchungen an RE/TM-Schichten bestätigen die aus der Literatur bekannten Eigenschaften. Sie lassen sich effektiv, und für magneto-optische Anwendungen geeignet, über RF-Sputtern herstellen. Die unmittelbaren Schicht-Parameter, wie Schichtdicke und Terbium-Konzentration, lassen sich über einfache Zusammenhänge einstellen. Da die Terbium-Konzentration eine Änderung der Kompensationstemperatur bewirkt, lässt sich diese mit Messungen am Kerr-Magnetometer überprüfen. Die für die Anwendung interessante senkrechte magnetische Anisotropie konnte ebenfalls mit den Herstellungsbedingungen verknüpft werden. Bei der Herstellung der Schichten auf einer glatten Glas-Oberfläche (Floatglas) zeigt die RE/TM-Schicht bereits in den ersten Lagen ein Wachstumsverhalten, das eine senkrechte Anisotropie bewirkt. Auf einer Quarzglas- oder Keramik-Oberfläche wachsen die ersten Lagen in einer durch das Substrat induzierten Struktur auf, danach ändert sich das Wachstumsverhalten stetig, bis eine senkrechte Anisotropie erreicht wird. Dieses Verhalten kann auch durch verschiedene Pufferschichten (Aluminium und Siliziumnitrid) nur unwesentlich beeinflusst werden [Kap. 5 & Kap. 6]. Bei der direkten Aufbringung von Doppelschichten, bestehend aus einer Auslese-Schicht (GdFeCo) auf einer Speicherschicht (TbFeCo), wurde die Austausch-Kopplung demonstriert. Die Ausleseschicht zeigt unterhalb der Kompensationstemperatur keine Kopplung an die Speicherschicht, während oberhalb der Kompensationstemperatur eine direkte Kopplung der Untergitter stattfindet. Daraus ergibt sich das für den MSR-Effekt erwünschte Maskierungsverhalten. Die vorher aus den Einzelschichten gewonnen Ergebnisse zu Kompensationstemperatur und Wachstumsverhalten konnten in den Doppelschichten wiedergefunden werden. Als Idealfall erweist sich hier die einfachste Struktur. Man bringt die Speicherschicht auf Floatglas auf und bedeckt diese direkt mit der Ausleseschicht [Kap. 7]. Weiterhin konnte gezeigt werden, dass es möglich ist, den Faraday-Effekt einer Granatschicht als verstärkendes Element zu nutzen. Im anwendungstauglichen, integrierten Schichtsystem konnten die kostengünstig, mit dem Sol-Gel-Verfahren produzierten, Granate die strukturellen Anforderungen nicht erfüllen, da sich während der Herstellung Risse und Löcher gebildet haben. Bei der experimentellen Realisierung mit einer einkristallinen Granatschicht und einer RE/TM-Schicht konnte die prinzipielle Eignung des Schichtsystems demonstriert werden [Kap. 8].

Development of hybrid UV VCSEL with organic active material and dielectric DBR mirrors for medical, sensoric and data storage applications

Lasers play an important role for medical, sensoric and data storage devices. This thesis is focused on design, technology development, fabrication and characterization of hybrid ultraviolet Vertical-Cavity Surface-Emitting Lasers (UV VCSEL) with organic laser-active material and inorganic distributed Bragg reflectors (DBR). Multilayer structures with different layer thicknesses, refractive indices and absorption coefficients of the inorganic materials were studied using theoretical model calculations. During the simulations the structure parameters such as materials and thicknesses have been varied. This procedure was repeated several times during the design optimization process including also the feedback from technology and characterization. Two types of VCSEL devices were investigated. The first is an index coupled structure consisting of bottom and top DBR dielectric mirrors. In the space in between them is the cavity, which includes active region and defines the spectral gain profile. In this configuration the maximum electrical field is concentrated in the cavity and can destroy the chemical structure of the active material. The second type of laser is a so called complex coupled VCSEL. In this structure the active material is placed not only in the cavity but also in parts of the DBR structure. The simulations show that such a distribution of the active material reduces the required pumping power for reaching lasing threshold. High efficiency is achieved by substituting the dielectric material with high refractive index for the periods closer to the cavity. The inorganic materials for the DBR mirrors have been deposited by Plasma- Enhanced Chemical Vapor Deposition (PECVD) and Dual Ion Beam Sputtering (DIBS) machines. Extended optimizations of the technological processes have been performed. All the processes are carried out in a clean room Class 1 and Class 10000. The optical properties and the thicknesses of the layers are measured in-situ by spectroscopic ellipsometry and spectroscopic reflectometry. The surface roughness is analyzed by atomic force microscopy (AFM) and images of the devices are taken with scanning electron microscope (SEM). The silicon dioxide (SiO2) and silicon nitride (Si3N4) layers deposited by the PECVD machine show defects of the material structure and have higher absorption in the ultra violet range compared to ion beam deposition (IBD). This results in low reflectivity of the DBR mirrors and also reduces the optical properties of the VCSEL devices. However PECVD has the advantage that the stress in the layers can be tuned and compensated, in contrast to IBD at the moment. A sputtering machine Ionsys 1000 produced by Roth&Rau company, is used for the deposition of silicon dioxide (SiO2), silicon nitride (Si3N4), aluminum oxide (Al2O3) and zirconium dioxide (ZrO2). The chamber is equipped with main (sputter) and assisted ion sources. The dielectric materials were optimized by introducing additional oxygen and nitrogen into the chamber. DBR mirrors with different material combinations were deposited. The measured optical properties of the fabricated multilayer structures show an excellent agreement with the results of theoretical model calculations. The layers deposited by puttering show high compressive stress. As an active region a novel organic material with spiro-linked molecules is used. Two different materials have been evaporated by utilizing a dye evaporation machine in the clean room of the department Makromolekulare Chemie und Molekulare Materialien (mmCmm). The Spiro-Octopus-1 organic material has a maximum emission at the wavelength λemission = 395 nm and the Spiro-Pphenal has a maximum emission at the wavelength λemission = 418 nm. Both of them have high refractive index and can be combined with low refractive index materials like silicon dioxide (SiO2). The sputtering method shows excellent optical quality of the deposited materials and high reflection of the multilayer structures. The bottom DBR mirrors for all VCSEL devices were deposited by the DIBS machine, whereas the top DBR mirror deposited either by PECVD or by combination of PECVD and DIBS. The fabricated VCSEL structures were optically pumped by nitrogen laser at wavelength λpumping = 337 nm. The emission was measured by spectrometer. A radiation of the VCSEL structure at wavelength 392 nm and 420 nm is observed.

High-Speed Semiconductor Lasers based on Low-Dimensional Active Materials for Optical Telecommunication

The scope of this work is the fundamental growth, tailoring and characterization of self-organized indium arsenide quantum dots (QDs) and their exploitation as active region for diode lasers emitting in the 1.55 µm range. This wavelength regime is especially interesting for long-haul telecommunications as optical fibers made from silica glass have the lowest optical absorption. Molecular Beam Epitaxy is utilized as fabrication technique for the quantum dots and laser structures. The results presented in this thesis depict the first experimental work for which this reactor was used at the University of Kassel. Most research in the field of self-organized quantum dots has been conducted in the InAs/GaAs material system. It can be seen as the model system of self-organized quantum dots, but is not suitable for the targeted emission wavelength. Light emission from this system at 1.55 µm is hard to accomplish. To stay as close as possible to existing processing technology, the In(AlGa)As/InP (100) material system is deployed. Depending on the epitaxial growth technique and growth parameters this system has the drawback of producing a wide range of nano species besides quantum dots. Best known are the elongated quantum dashes (QDash). Such structures are preferentially formed, if InAs is deposited on InP. This is related to the low lattice-mismatch of 3.2 %, which is less than half of the value in the InAs/GaAs system. The task of creating round-shaped and uniform QDs is rendered more complex considering exchange effects of arsenic and phosphorus as well as anisotropic effects on the surface that do not need to be dealt with in the InAs/GaAs case. While QDash structures haven been studied fundamentally as well as in laser structures, they do not represent the theoretical ideal case of a zero-dimensional material. Creating round-shaped quantum dots on the InP(100) substrate remains a challenging task. Details of the self-organization process are still unknown and the formation of the QDs is not fully understood yet. In the course of the experimental work a novel growth concept was discovered and analyzed that eases the fabrication of QDs. It is based on different crystal growth and ad-atom diffusion processes under supply of different modifications of the arsenic atmosphere in the MBE reactor. The reactor is equipped with special valved cracking effusion cells for arsenic and phosphorus. It represents an all-solid source configuration that does not rely on toxic gas supply. The cracking effusion cell are able to create different species of arsenic and phosphorus. This constitutes the basis of the growth concept. With this method round-shaped QD ensembles with superior optical properties and record-low photoluminescence linewidth were achieved. By systematically varying the growth parameters and working out a detailed analysis of the experimental data a range of parameter values, for which the formation of QDs is favored, was found. A qualitative explanation of the formation characteristics based on the surface migration of In ad-atoms is developed. Such tailored QDs are finally implemented as active region in a self-designed diode laser structure. A basic characterization of the static and temperature-dependent properties was carried out. The QD lasers exceed a reference quantum well laser in terms of inversion conditions and temperature-dependent characteristics. Pulsed output powers of several hundred milli watt were measured at room temperature. In particular, the lasers feature a high modal gain that even allowed cw-emission at room temperature of a processed ridge wave guide device as short as 340 µm with output powers of 17 mW. Modulation experiments performed at the Israel Institute of Technology (Technion) showed a complex behavior of the QDs in the laser cavity. Despite the fact that the laser structure is not fully optimized for a high-speed device, data transmission capabilities of 15 Gb/s combined with low noise were achieved. To the best of the author`s knowledge, this renders the lasers the fastest QD devices operating at 1.55 µm. The thesis starts with an introductory chapter that pronounces the advantages of optical fiber communication in general. Chapter 2 will introduce the fundamental knowledge that is necessary to understand the importance of the active region`s dimensions for the performance of a diode laser. The novel growth concept and its experimental analysis are presented in chapter 3. Chapter 4 finally contains the work on diode lasers.

Molecular Beam Epitaxial Growth of III-V Semiconductor Nanostructures on Silicon Substrates

The main focus and concerns of this PhD thesis is the growth of III-V semiconductor nanostructures (Quantum dots (QDs) and quantum dashes) on silicon substrates using molecular beam epitaxy (MBE) technique. The investigation of influence of the major growth parameters on their basic properties (density, geometry, composition, size etc.) and the systematic characterization of their structural and optical properties are the core of the research work. The monolithic integration of III-V optoelectronic devices with silicon electronic circuits could bring enormous prospect for the existing semiconductor technology. Our challenging approach is to combine the superior passive optical properties of silicon with the superior optical emission properties of III-V material by reducing the amount of III-V materials to the very limit of the active region. Different heteroepitaxial integration approaches have been investigated to overcome the materials issues between III-V and Si. However, this include the self-assembled growth of InAs and InGaAs QDs in silicon and GaAx matrices directly on flat silicon substrate, sitecontrolled growth of (GaAs/In0,15Ga0,85As/GaAs) QDs on pre-patterned Si substrate and the direct growth of GaP on Si using migration enhanced epitaxy (MEE) and MBE growth modes. An efficient ex-situ-buffered HF (BHF) and in-situ surface cleaning sequence based on atomic hydrogen (AH) cleaning at 500 °C combined with thermal oxide desorption within a temperature range of 700-900 °C has been established. The removal of oxide desorption was confirmed by semicircular streaky reflection high energy electron diffraction (RHEED) patterns indicating a 2D smooth surface construction prior to the MBE growth. The evolution of size, density and shape of the QDs are ex-situ characterized by atomic-force microscopy (AFM) and transmission electron microscopy (TEM). The InAs QDs density is strongly increased from 108 to 1011 cm-2 at V/III ratios in the range of 15-35 (beam equivalent pressure values). InAs QD formations are not observed at temperatures of 500 °C and above. Growth experiments on (111) substrates show orientation dependent QD formation behaviour. A significant shape and size transition with elongated InAs quantum dots and dashes has been observed on (111) orientation and at higher Indium-growth rate of 0.3 ML/s. The 2D strain mapping derived from high-resolution TEM of InAs QDs embedded in silicon matrix confirmed semi-coherent and fully relaxed QDs embedded in defectfree silicon matrix. The strain relaxation is released by dislocation loops exclusively localized along the InAs/Si interfaces and partial dislocations with stacking faults inside the InAs clusters. The site controlled growth of GaAs/In0,15Ga0,85As/GaAs nanostructures has been demonstrated for the first time with 1 μm spacing and very low nominal deposition thicknesses, directly on pre-patterned Si without the use of SiO2 mask. Thin planar GaP layer was successfully grown through migration enhanced epitaxy (MEE) to initiate a planar GaP wetting layer at the polar/non-polar interface, which work as a virtual GaP substrate, for the GaP-MBE subsequently growth on the GaP-MEE layer with total thickness of 50 nm. The best root mean square (RMS) roughness value was as good as 1.3 nm. However, these results are highly encouraging for the realization of III-V optical devices on silicon for potential applications.

Piezoelectric Ultrasonic Micromotors

This report describes development of micro-fabricated piezoelectric ultrasonic motors and bulk-ceramic piezoelectric ultrasonic motors. Ultrasonic motors offer the advantage of low speed, high torque operation without the need for gears. They can be made compact and lightweight and provide a holding torque in the absence of applied power, due to the traveling wave frictional coupling mechanism between the rotor and the stator. This report covers modeling, simulation, fabrication and testing of ultrasonic motors. Design of experiments methods were also utilized to find optimal motor parameters. A suite of 8 mm diameter x 3 mm tall motors were machined for these studies and maximum stall torques as large as 10^(- 3) Nm, maximum no-load speeds of 1710 rpm and peak power outputs of 27 mW were realized. Aditionally, this report describes the implementation of a microfabricated ultrasonic motor using thin-film lead zirconate titanate. In a joint project with the Pennsylvania State University Materials Research Laboratory and MIT Lincoln Laboratory, 2 mm and 5 mm diameter stator structures were fabricated on 1 micron thick silicon nitride membranes. Small glass lenses placed down on top spun at 100-300 rpm with 4 V excitation at 90 kHz. The large power densities and stall torques of these piezoelectric ultrasonic motors offer tremendous promis for integrated machines: complete intelligent, electro-mechanical autonomous systems mass-produced in a single fabrication process.

Characterization of ZnO Nanorods Grown on GaN Using Aqueous Solution Method

Uniformly distributed ZnO nanorods with diameter 70-100 nm and 1-2μm long have been successfully grown at low temperatures on GaN by using the inexpensive aqueous solution method. The formation of the ZnO nanorods and the growth parameters are controlled by reactant concentration, temperature and pH. No catalyst is required. The XRD studies show that the ZnO nanorods are single crystals and that they grow along the c axis of the crystal plane. The room temperature photoluminescence measurements have shown ultraviolet peaks at 388nm with high intensity, which are comparable to those found in high quality ZnO films. The mechanism of the nanorod growth in the aqueous solution is proposed. The dependence of the ZnO nanorods on the growth parameters was also investigated. While changing the growth temperature from 60°C to 150°C, the morphology of the ZnO nanorods changed from sharp tip (needle shape) to flat tip (rod shape). These kinds of structure are useful in laser and field emission application.

High Density Single Crystalline GaN Nanodot Arrays Fabricated Using Template-Assisted Selective Growth

High density, uniform GaN nanodot arrays with controllable size have been synthesized by using template-assisted selective growth. The GaN nanodots with average diameter 40nm, 80nm and 120nm were selectively grown by metalorganic chemical vapor deposition (MOCVD) on a nano-patterned SiO2/GaN template. The nanoporous SiO2 on GaN surface was created by inductively coupled plasma etching (ICP) using anodic aluminum oxide (AAO) template as a mask. This selective regrowth results in highly crystalline GaN nanodots confirmed by high resolution transmission electron microscopy. The narrow size distribution and uniform spatial position of the nanoscale dots offer potential advantages over self-assembled dots grown by the Stranski–Krastanow mode.

Growth of ZnO Nanorods on GaN Using Aqueous Solution Method

Uniformly distributed ZnO nanorods with diameter 80-120 nm and 1-2µm long have been successfully grown at low temperatures on GaN by using the inexpensive aqueous solution method. The formation of the ZnO nanorods and the growth parameters are controlled by reactant concentration, temperature and pH. No catalyst is required. The XRD studies show that the ZnO nanorods are single crystals and that they grow along the c axis of the crystal plane. The room temperature photoluminescence measurements have shown ultraviolet peaks at 388nm with high intensity, which are comparable to those found in high quality ZnO films. The mechanism of the nanorod growth in the aqueous solution is proposed. The dependence of the ZnO nanorods on the growth parameters was also investigated. While changing the growth temperature from 60°C to 150°C, the morphology of the ZnO nanorods changed from sharp tip with high aspect ratio to flat tip with smaller aspect ratio. These kinds of structure are useful in laser and field emission application.

High Optical Quality Nanoporous GaN Prepared by Photoelectrochemical Etching

Nanoporous GaN films are prepared by UV assisted electrochemical etching using HF solution as an electrolyte. To assess the optical quality and morphology of these nanoporous films, micro-photoluminescence (PL), micro-Raman scattering, scanning electron microscopy (SEM), and atomic force microscopy (AFM) techniques have been employed. SEM and AFM measurements revealed an average pore size of about 85-90 nm with a transverse dimension of 70-75 nm. As compared to the as-grown GaN film, the porous layer exhibits a substantial photoluminescence intensity enhancement with a partial relaxation of compressive stress. Such a stress relaxation is further confirmed by the red shifted E₂(TO) phonon peak in the Raman spectrum of porous GaN.

The Influence of Adjacent Segment on the Reliability of Cu Dual Damascene Interconnects

Three terminal ‘dotted-I’ interconnect structures, with vias at both ends and an additional via in the middle, were tested under various test conditions. Mortalities (failures) were found in right segments with jL value as low as 1250 A/cm, and the mortality of a dotted-I segment is dependent on the direction and magnitude of the current in the adjacent segment. Some mortalities were also found in the right segments under a test condition where no failure was expected. Cu extrusion along the delaminated Cu/Si₃N₄ interface near the central via region was believed to cause the unexpected failures. From the time-to-failure (TTF), it is possible to quantify the Cu/Si₃N₄ interfacial strength and bonding energy. Hence, the demonstrated test methodology can be used to investigate the integrity of the Cu dual damascene processes. As conventionally determined critical jL values in two-terminal via-terminated lines cannot be directly applied to interconnects with branched segments, this also serves as a good methodology to identify the critical effective jL values for immortality.

Osteomielitis esternal: utilidad de las pruebas de diagnóstico por imágenes con enfoque en medicina nuclear

Introducción: El diagnóstico de osteomielitis esternal post-esternotomía resulta difícil empleando síntomas clínicos o de laboratorio y las imágenes morfológicas orientan a sospecha más que al diagnóstico. Un diagnóstico precoz ofrece calidad de vida y el mejor tratamiento para reducir una mortalidad que oscila entre 14% y 47%. La gammagrafía con leucocitos marcados ofrece el mejor rendimiento diagnóstico para infecciones y se destaca como el patrón de oro diagnóstico. Objetivo: Identificar el desempeño y utilidad de la gammagrafía con leucocitos autólogos marcados con 99mTc-HMPAO en los estudios realizados para la evaluación de osteomielitis esternal. Materiales y métodos: Se realizó un estudio descriptivo, retrospectivo de prueba diagnóstica en la Fundación Cardioinfantil de Bogotá entre enero/2010 y mayo/2015 evaluando gammagrafías con leucocitos marcados ante la sospecha de osteomielitis posterior a esternotomía. Resultados: Se evaluaron 52 pacientes, en los que la gammagrafía con leucocitos mostró 23 pacientes (44,2%) con osteomielitis esternal, logrando una sensibilidad y especificidad del 88,46% y 100% respectivamente. El valor predictivo positivo fue de 100%, y el valor predictivo negativo fue de 89,66%. El impacto de una prueba negativa no modificó el manejo médico inicial en el 93% de los casos mientras que una prueba positiva lo modificó en el 83%. Conclusiones: La gammagrafía con leucocitos autólogos radiomarcados con 99mTc-HMPAO continúa siendo el patrón de oro de referencia no invasiva para el diagnóstico de osteomielitis, y en el caso de osteomielitis esternal se convierte en la prueba de elección pertinente en la selección de pacientes que ameritan una re-intervención quirúrgica.

Determination of the direct band-gap energy of InAlAs matched to InP by photoluminescence excitation spectroscopy

A series of InxAl1-xAs samples (0.51≪x≪0.55)coherently grown on InP was studied in order to measure the band-gap energy of the lattice matched composition. As the substrate is opaque to the relevant photon energies, a method is developed to calculate the optical absorption coefficient from the photoluminescence excitation spectra. The effect of strain on the band-gap energy has been taken into account. For x=0.532, at 14 K we have obtained Eg0=1549±6 meV

Atomic diffusion induced by stress relaxation in InGaAs/GaAs epitaxial layers

The origin of the microscopic inhomogeneities in InxGa1-xAs layers grown on GaAs by molecular beam epitaxy is analyzed through the optical absorption spectra near the band gap. It is seen that, for relaxed thick layers of about 2.8μm, composition inhomogeneities are responsible for the band edge smoothing into the whole compositional range (0.05

Si3N4 single-crystal nanowires grown from silicon micro- and nanoparticles near the threshold of passive oxidation

A simple and most promising oxide-assisted catalyst-free method is used to prepare silicon nitride nanowires that give rise to high yield in a short time. After a brief analysis of the state of the art, we reveal the crucial role played by the oxygen partial pressure: when oxygen partial pressure is slightly below the threshold of passive oxidation, a high yield inhibiting the formation of any silica layer covering the nanowires occurs and thanks to the synthesis temperature one can control nanowire dimensions