Development and test of resistive superconducting fault current limiter; acting time and its recovery conditions

Resistive-type of superconducting fault current limiters (RSFCL) have been developed for medium voltage class aiming to operate at 1 MVA power capacity and short time recovery (< 2 s). A RSFCL in form of superconducting modular device was designed and constructed using 50 m-length of YBCO coated conductor tapes for operation under 1 kV / 1 kA and acting time of 0.1 s. In order to increase the acting time the RSFCL was combined with an air-core reactor in parallel to increase the fault limiting time up to 1 s. The tests determined the electrical and thermal characteristics of the combined resistive/ inductive protection unit. The combined fault current limiter reached a limiting current of 583 A, corresponding to a limiting factor of 3.3 times within an acting time of up to 1 s.

A new family of zero-current-switching PWM converters and a novel HPF-ZCS-PWM boost rectifier

A new family of direct current (DC) to DC converters based on a zero current switching pulse width modulated (ZCS-PWM) soft commutation cell is presented. This ZCS-PWM cell is consists of two transistors, two diodes, two inductors and one capacitor; and provides zero voltage turn-on to the diodes, a zero-current turn-on and a zero-current zero-voltage turn-off to the transistors. In addition, a new commutation cell in a new ZCS-PWM boost rectifier is developed, obtaining a structure with power factor near the unity, high efficiency at wide load range and low total harmonic distortion in the input current.

Life cycle assessment applied to municipal solid waste management: a case study

This study analyzes the environmental performance of the Municipal Solid Waste Management System (MSWMS) of Piedade, São Paulo, from a systemic perspective. A life cycle assessment (LCA) technique was applied according to an attributional approach to evaluate both the current operational situation and different prospective scenarios, which were devised based on the application of targets for recycling dry and wet waste suggested by the pre-draft version of the Brazilian Plan for Solid Waste. The life cycle impact assessment method EcoIndicator 99, in association with normalization and weighting procedures, was used to conduct the analysis. It was observed that the adoption of goals of 30%, 50% and 70% for recovering of the recyclable dry waste, resulted in improvement of the environmental performance of the waste management system under analysis, respectively of 10%, 15% and 20%. It was also possible to detect an evolution in the order of 54% in reducing impacts resulting from the adoption of targets for composting. LCA proved to be effective for the evaluation of the environmental performance of MSWMS-Piedade. However, for future evaluations, the attributional approach should be replaced by the methodological practice of substitution to enable the avoided burdens to be considered in estimations of the environmental performance municipal solid waste management systems.

Comparative degradation of ZnO- and SnO(2)-based polycrystalline non-ohmic devices by current pulse stress

The degradation behaviour of SnO(2)-based varistors (SCNCr) due to current pulses (8/20 mu s) is reported here for the first time in comparison with the ZnO-based commercial varistors (ZnO). Puncturing and/or cracking failures were observed in ZnO-based varistors possessing inferior thermo-mechanical properties in comparison with that found in a SCNCr system free of failures. Both systems presented electric degradation related to the increase in the leakage current and decrease in the electric breakdown field, non-linear coefficient and average value of the potential barrier height. However, it was found that a more severe degradation occurred in the ZnO-based varistors concerning their non-ohmic behaviour, while in the SCNCr system, a strong non-ohmic behaviour remained after the degradation. These results indicate that the degradation in the metal oxide varistors is controlled by a defect diffusion process whose rate depends on the mobility, the concentration of meta-stable defects and the amount of electrically active interfaces. The improved behaviour of the SCNCr system is then inferred to be associated with the higher amount of electrically active interfaces (85%) and to a higher energy necessary to activate the diffusion of the specific defects.

Is the meander growth in the Brazil Current system off Southeast Brazil due to baroclinic instability?

Temporally-growing frontal meandering and occasional eddy-shedding is observed in the Brazil Current (BC) as it flows adjacent to the Brazilian Coast. No study of the dynamics of this phenomenon has been conducted to date in the region between 22 degrees S and 25 degrees S. Within this latitude range, the flow over the intermediate continental slope is marked by a current inversion at a depth that is associated with the Intermediate Western Boundary Current (IWBC). A time series analysis of 10-current-meter mooring data was used to describe a mean vertical profile for the BC-IWBC jet and a typical meander vertical structure. The latter was obtained by an empirical orthogonal function (EOF) analysis that showed a single mode explaining 82% of the total variance. This mode structure decayed sharply with depth, revealing that the meandering is much more vigorous within the BC domain than it is in the IWBC region. As the spectral analysis of the mode amplitude time series revealed no significant periods, we searched for dominant wavelengths. This search was done via a spatial EOF analysis on 51 thermal front patterns derived from digitized AVHRR images. Four modes were statistically significant at the 95% confidence level. Modes 3 and 4, which together explained 18% of the total variance, are associated with 266 and 338-km vorticity waves, respectively. With this new information derived from the data, the [Johns, W.E., 1988. One-dimensional baroclinically unstable waves on the Gulf Stream potential vorticity gradient near Cape Hatteras. Dyn. Atmos. Oceans 11, 323-350] one-dimensional quasi-geostrophic model was applied to the interpolated mean BC-IWBC jet. The results indicated that the BC system is indeed baroclinically unstable and that the wavelengths depicted in the thermal front analysis are associated with the most unstable waves produced by the model. Growth rates were about 0.06 (0.05) days(-1) for the 266-km (338-km) wave. Moreover, phase speeds for these waves were low compared to the surface BC velocity and may account for remarks in the literature about growing standing or stationary meanders off southeast Brazil. The theoretical vertical structure modes associated with these waves resembled very closely to the one obtained for the current-meter mooring EOF analysis. We interpret this agreement as a confirmation that baroclinic instability is an important mechanism in meander growth in the BC system. (C) 2008 Elsevier B.V. All rights reserved.

Theoretical chemistry: current applications to photochemistry and thermochemistry

A historical perspective is given contrasting challenges and advances in theoretical chemistry at the time the first issue of Theoretical Chemistry Accounts appeared in 1962 and the progress achieved since then as expressed in current state-of-the-art applications in photochemistry and thermochemistry.

Surface-Potential-Based Drain Current Analytical Model for Triple-Gate Junctionless Nanowire Transistors

This paper proposes a drain current model for triple-gate n-type junctionless nanowire transistors. The model is based on the solution of the Poisson equation. First, the 2-D Poisson equation is used to obtain the effective surface potential for long-channel devices, which is used to calculate the charge density along the channel and the drain current. The solution of the 3-D Laplace equation is added to the 2-D model in order to account for the short-channel effects. The proposed model is validated using 3-D TCAD simulations where the drain current and its derivatives, the potential, and the charge density have been compared, showing a good agreement for all parameters. Experimental data of short- channel devices down to 30 nm at different temperatures have been also used to validate the model.

Optical transition radiation used in the diagnostic of low energy and low current electron beams in particle accelerators

Optical transition radiation (OTR) plays an important role in beam diagnostics for high energy particle accelerators. Its linear intensity with beam current is a great advantage as compared to fluorescent screens, which are subject to saturation. Moreover, the measurement of the angular distribution of the emitted radiation enables the determination of many beam parameters in a single observation point. However, few works deals with the application of OTR to monitor low energy beams. In this work we describe the design of an OTR based beam monitor used to measure the transverse beam charge distribution of the 1.9-MeV electron beam of the linac injector of the IFUSP microtron using a standard vision machine camera. The average beam current in pulsed operation mode is of the order of tens of nano-Amps. Low energy and low beam current make OTR observation difficult. To improve sensitivity, the beam incidence angle on the target was chosen to maximize the photon flux in the camera field-of-view. Measurements that assess OTR observation (linearity with beam current, polarization, and spectrum shape) are presented, as well as a typical 1.9-MeV electron beam charge distribution obtained from OTR. Some aspects of emittance measurement using this device are also discussed. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4748519]

Light emission and current rectification in a molecular device: Experiment and theory

We have investigated optical and transport properties of the molecular structure 2,3,4,5-tetraphenyl-1-phenylethynyl-cyclopenta-2,4-dienol experimentally and theoretically. The optical spectrum was calculated using Hartree-Fock-intermediate neglect of differential overlap-configuration interaction model. The experimental photoluminescence spectrum showed a peak around 470nm which was very well described by the modeling. Electronic transport measurements showed a diode-like effect with a strong current rectification. A phenomenological microscopic model based on non-equilibrium Green's function technique was proposed and a very good description electronic transport was obtained. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4767457]

Influence of normal and radial contributions of local current density on local electrochemical impedance spectroscopy

A new tri-electrode probe is presented and applied to local electrochemical impedance spectroscopy (LEIS) measurements. As opposed to two-probe systems, the three-probe one allows measurement not only of normal, but also of radial contributions of local current densities to the local impedance values. The results concerning the cases of the blocking electrode and the electrode with faradaic reaction are discussed from the theoretical point of view for a disk electrode. Numerical simulations and experimental results are compared for the case of the ferri/ferrocyanide electrode reaction at the Pt working electrode disk. At the centre of the disk, the impedance taking into account both normal and radial contributions was in good agreement with the local impedance measured in terms of only the normal contribution. At the periphery of the electrode, the impedance taking into account both normal and radial contributions differed significantly from the local impedance measured in terms of only the normal contribution. The radial impedance results at the periphery of the electrode are in good agreement with the usual explanation that the associated larger current density is attributed to the geometry of the electrode, which exhibits a greater accessibility at the electrode edge. (C) 2011 Elsevier Ltd. All rights reserved.

Temperature impact on the tunnel fet off-state current components

In this work, the temperature impact on the off-state current components is analyzed through numerical simulation and experimentally. First of all, the band-to-band tunneling is studied by varying the underlap in the channel/drain junction, leading to an analysis of the different off-state current components. For pTFET devices, the best behavior for off-state current was obtained for higher values of underlap (reduced BTBT) and at low temperatures (reduced SRH and TAT). At high temperature, an unexpected off-state current occurred due to the thermal leakage current through the drain/channel junction. Besides, these devices presented a good performance when considering the drain current as a function of the drain voltage, making them suitable for analog applications. (C) 2012 Elsevier Ltd. All rights reserved.

Current perspectives in avian salmonellosis: Vaccines and immune mechanisms of protection

Salmonellosis is one of the most prevalent foodborne diseases worldwide. Food animals have been identified as reservoirs for nontyphoid Salmonella infections. in poultry, host-specific Salmonella infections cause fowl typhoid and pullorum diseases that produce economic losses in different parts of the world. Several measures have been used to prevent and control Salmonella infections in poultry, and vaccination is the most practical measure because it avoids contamination of poultry products and by-products and prevents disease in humans. Salmonella vaccines can decrease public health risk by reducing colonization and organ invasion, including invasion of reproductive tissues, and by diminishing fecal shedding and environmental contamination. We review available information on the host-specific and non-host-specific Salmonella serotypes found in poultry and the improved understanding of the pathogenesis of and immune responses to infection. We also include some approaches based on updated publications regarding killed and live attenuated vaccines and their immune mechanisms of protection.

Evaluation of a multi variated analysis for the selection of t-tbar multijet events in the current CMS implemented environment at LHC

In the present study we are using multi variate analysis techniques to discriminate signal from background in the fully hadronic decay channel of ttbar events. We give a brief introduction to the role of the Top quark in the standard model and a general description of the CMS Experiment at LHC. We have used the CMS experiment computing and software infrastructure to generate and prepare the data samples used in this analysis. We tested the performance of three different classifiers applied to our data samples and used the selection obtained with the Multi Layer Perceptron classifier to give an estimation of the statistical and systematical uncertainty on the cross section measurement.

An AMSTAR assessment of the methodological quality of systematic reviews of oral healthcare interventions published in the Journal of Applied Oral Science (JAOS)

Systematic reviews are not an assembly of anecdotes but a distillation of current best available evidence on a particular topic and as such have an important role to play in evidence-based healthcare. A substantial proportion of these systematic reviews focus on interventions, and are able to provide clinicians with the opportunity to understand and translate the best available evidence on the effects of these healthcare interventions into clinical practice. The importance of systematic reviews in summarising and identifying the gaps in evidence which might inform new research initiatives is also widely acknowledged. Their potential impact on practice and research makes their methodological quality especially important as it may directly influence their utility for clinicians, patients and policy makers. The objectives of this study were to identify systematic reviews of oral healthcare interventions published in the Journal of Applied Oral Science (JAOS) and to evaluate their methodological quality using the evaluation tool, AMSTAR.

Double Take Project: Using Applied Theatre For Campus Climate Change

Despite research gathered in the Campus Climate Report, I believe that it underrepresented the student experience of the social scene. The document primarily served as an identification tool for four major problems on campus: binge drinking, sexual assault, diversity, and disengagement in the classroom. Double Take Project also identifies similar issues however, this project uses theatrical techniques to gather the anecdotal reality of the student perspective. Double Take Project expands beyond the Campus Climate Report to inspire dialogue in a variety of student-to-student interactions and, more importantly, the project seeks action and solution plans. The social scene dominates our culture and its many issues result in concern for the safety, self-identity, and development of Bucknell students into thriving adults. Double Take Project is rooted in the belief that theatre is a palpable tool for social change. Over the course of many events, Double Take Project has utilized facets of theatre to provide opportunities to voice discontent, widen perception of normalcy on campus, and inspire confidence to act on personal beliefs. The Double Take Project uses many Applied Theatre methods to impact the social scene. For example, I conducted 36 student interviews and transformed the stories into a one-woman show, Rage Behind Curtains, which I performed at multiple venues across campus. I also used interviews to create a radio show airing one story per day. I conducted ten workshops with student groups, Fraternities and Sororities, and in the classroom utilizing Augusto Boal’s Theatre of the Oppressed (TO) techniques. I also created a “social scene confessional” where I stood outside the Elaine Langone Center with a sign that read, “Tell me a story about the social scene” from a wide variety of Bucknell students. Finally, I have assembled a Forum Theatre Company based on Augusto Boal’s method of the spect-actor, utilizing participants as both actors and spectators in the theatre piece. All of the names indicated in this paper have been altered to protect the identity of the participants. While planning events and conducting various theatrical experiences, I learned that there are a series of internal and external issues contributing to our social environment. Internally, students are conflicted with personal beliefs while battling outward social pressure. Whether they are on the outskirts or center of the social scene determines their response to this conflict. For example, I have discovered that students on the borders of the social culture respond with criticism because they feel excluded, whereas the student’s centrally involved critique the culture in private and while their persona appears to not want change. Externally, there are many structural issues that contribute to the current social climate such as without Fraternity meal plans, Cafeteria space is not sufficient to feed all of the students, exclusive party culture, and gendered housing. Through meetings with Deans and staff, I have learned there are also problems between administration and students, resulting in resentment and blame. Although addressing structural issues would instigate immediate change, in my opinion, internal student conflicts are the primary cause for the current negative social atmosphere. I believe that pressure to conform is rooted in lack of personal identity. Because students simply do not know themselves, they form strong social groups that become the definition of themselves. Without confident self-awareness, large and powerful groups coerce students to accept social norms resulting in the individual’s outward distaste for change, yet internal discomfort.