Statistical finite element model for bone shape and biomechanical properties

We present a framework for statistical finite element analysis combining shape and material properties, and allowing performing statistical statements of biomechanical performance across a given population. In this paper, we focus on the design of orthopaedic implants that fit a maximum percentage of the target population, both in terms of geometry and biomechanical stability. CT scans of the bone under consideration are registered non-rigidly to obtain correspondences in position and intensity between them. A statistical model of shape and intensity (bone density) is computed by means of principal component analysis. Afterwards, finite element analysis (FEA) is performed to analyse the biomechanical performance of the bones. Realistic forces are applied on the bones and the resulting displacement and bone stress distribution are calculated. The mechanical behaviour of different PCA bone instances is compared.

Comparison of modal analysis results of laser vibrometry and nearfield acoustical holography measurements of an aluminum plate

Noise and vibration has long been sought to be reduced in major industries: automotive, aerospace and marine to name a few. Products must be tested and pass certain levels of federally regulated standards before entering the market. Vibration measurements are commonly acquired using accelerometers; however limitations of this method create a need for alternative solutions. Two methods for non-contact vibration measurements are compared: Laser Vibrometry, which directly measures the surface velocity of the aluminum plate, and Nearfield Acoustic Holography (NAH), which measures sound pressure in the nearfield, and using Green’s Functions, reconstructs the surface velocity at the plate. The surface velocity from each method is then used in modal analysis to determine the comparability of frequency, damping and mode shapes. Frequency and mode shapes are also compared to an FEA model. Laser Vibrometry is a proven, direct method for determining surface velocity and subsequently calculating modal analysis results. NAH is an effective method in locating noise sources, especially those that are not well separated spatially. Little work has been done in incorporating NAH into modal analysis.

DEVELOPMENT OF CONFORMABLE CNG TANK FOR AUTOMOTIVE APPLICATION

The purpose of this study is to design, develop and integrate a Compressed Natural Gas (CNG) tank that will have a conformable shape for efficient storage in a light-duty pick-up truck. The CNG tank will be a simple rectangular box geometry to demonstrate capability of non-cylindrical shapes. Using CAD drawings of the truck, a conformable tank will be designed to fit under the pick-up bed. The intent of the non-cylindrical CNG tank is to demonstrate improvement in size over the current solution, which is a large cylinder in the box of a pick-up truck. The geometry of the tank’s features is critical to its size and strength. The optimized tank design will be simulated with Finite Element Analysis (FEA) to determine critical stress regions, and appropriate design changes will be made to reduce stress concentration. Following the American National Standard Institute (ANSI) guide, different aluminum alloys will be optimized to obtain the best possible result for the CNG tank.

Prozessoptimierung des SLM-Prozesses mit hoch-reflektiven und thermisch sehr gut leitenden Materialien durch systematische Parameterfindung und begleitende Simulationen am Beispiel von Silber

Additive Manufacturing durch Aufschmelzen von Metallpulvern hat sich auf breiter Front als Herstellverfahren, auch für Endprodukte, etabliert. Besonders für die Variante des Selective Laser Melting (SLM) sind Anwendungen in der Zahntechnik bereits weit verbreitet und der Einsatz in sensitiven Branchen wie der Luftfahrt ist in greifbare Nähe gerückt. Deshalb werden auch vermehrt Anstrengungen unternommen, um bisher nicht verarbeitete Materialien zu qualifizieren. Dies sind vorzugsweise Nicht-Eisen- und Edelmetalle, die sowohl eine sehr hohe Reflektivität als auch eine sehr gute Wärmeleitfähigkeit aufweisen – beides Eigenschaften, die die Beherrschung des Laser-Schmelzprozesses erschweren und nur kleine Prozessfenster zulassen. Die Arbeitsgruppe SLM des Lehr- und Forschungsgebietes Hochleistungsverfahren der Fertigungstechnik hat sich unter der Randbedingung einer kleinen und mit geringer Laserleistung ausgestatteten SLM Maschine der Aufgabe gewidmet und am Beispiel von Silber die Parameterfelder für Einzelspuren und wenig komplexe Geometrien systematisch untersucht. Die Arbeiten wurden von FEM Simulationen begleitet und durch metallographische Untersuchungen verifiziert. Die Ergebnisse bilden die Grundlage zur schnellen Parameterfindung bei komplexen Geometrien und bei Veränderungen der Zusammensetzung, wie sie bei zukünftigen Legierungen zu erwarten sind. Die Ergebnisse werden exemplarisch auf unterschiedliche Geometrien angewandt und entsprechende Bauteile gezeigt.

Ontologies and Methods for Interoperability of Engineering Analysis Models (EAMS) in an E-Design Environment

ABSTRACT ONTOLOGIES AND METHODS FOR INTEROPERABILITY OF ENGINEERING ANALYSIS MODELS (EAMS) IN AN E-DESIGN ENVIRONMENT SEPTEMBER 2007 NEELIMA KANURI, B.S., BIRLA INSTITUTE OF TECHNOLOGY AND SCIENCES PILANI INDIA M.S., UNIVERSITY OF MASSACHUSETTS AMHERST Directed by: Professor Ian Grosse Interoperability is the ability of two or more systems to exchange and reuse information efficiently. This thesis presents new techniques for interoperating engineering tools using ontologies as the basis for representing, visualizing, reasoning about, and securely exchanging abstract engineering knowledge between software systems. The specific engineering domain that is the primary focus of this report is the modeling knowledge associated with the development of engineering analysis models (EAMs). This abstract modeling knowledge has been used to support integration of analysis and optimization tools in iSIGHT FD , a commercial engineering environment. ANSYS , a commercial FEA tool, has been wrapped as an analysis service available inside of iSIGHT-FD. Engineering analysis modeling (EAM) ontology has been developed and instantiated to form a knowledge base for representing analysis modeling knowledge. The instances of the knowledge base are the analysis models of real world applications. To illustrate how abstract modeling knowledge can be exploited for useful purposes, a cantilever I-Beam design optimization problem has been used as a test bed proof-of-concept application. Two distinct finite element models of the I-beam are available to analyze a given beam design- a beam-element finite element model with potentially lower accuracy but significantly reduced computational costs and a high fidelity, high cost, shell-element finite element model. The goal is to obtain an optimized I-beam design at minimum computational expense. An intelligent KB tool was developed and implemented in FiPER . This tool reasons about the modeling knowledge to intelligently shift between the beam and the shell element models during an optimization process to select the best analysis model for a given optimization design state. In addition to improved interoperability and design optimization, methods are developed and presented that demonstrate the ability to operate on ontological knowledge bases to perform important engineering tasks. One such method is the automatic technical report generation method which converts the modeling knowledge associated with an analysis model to a flat technical report. The second method is a secure knowledge sharing method which allocates permissions to portions of knowledge to control knowledge access and sharing. Both the methods acting together enable recipient specific fine grain controlled knowledge viewing and sharing in an engineering workflow integration environment, such as iSIGHT-FD. These methods together play a very efficient role in reducing the large scale inefficiencies existing in current product design and development cycles due to poor knowledge sharing and reuse between people and software engineering tools. This work is a significant advance in both understanding and application of integration of knowledge in a distributed engineering design framework.

Early changes in biochemical markers of bone formation during teriparatide therapy correlate with improvements in vertebral strength in men with glucocorticoid-induced osteoporosis

Summary Changes of the bone formation marker PINP correlated positively with improvements in vertebral strength in men with glucocorticoid-induced osteoporosis (GIO) who received 18-month treatment with teriparatide, but not with risedronate. These results support the use of PINP as a surrogate marker of bone strength in GIO patients treated with teriparatide. Introduction To investigate the correlations between biochemical markers of bone turnover and vertebral strength estimated by finite element analysis (FEA) in men with GIO. Methods A total of 92 men with GIO were included in an 18-month, randomized, open-label trial of teriparatide (20 μg/day, n = 45) and risedronate (35 mg/week, n = 47). High-resolution quantitative computed tomography images of the 12th thoracic vertebra obtained at baseline, 6 and 18 months were converted into digital nonlinear FE models and subjected to anterior bending, axial compression and torsion. Stiffness and strength were computed for each model and loading mode. Serum biochemical markers of bone formation (amino-terminal-propeptide of type I collagen [PINP]) and bone resorption (type I collagen cross-linked C-telopeptide degradation fragments [CTx]) were measured at baseline, 3 months, 6 months and 18 months. A mixed-model of repeated measures analysed changes from baseline and between-group differences. Spearman correlations assessed the relationship between changes from baseline of bone markers with FEA variables. Results PINP and CTx levels increased in the teriparatide group and decreased in the risedronate group. FEA-derived parameters increased in both groups, but were significantly higher at 18 months in the teriparatide group. Significant positive correlations were found between changes from baseline of PINP at 3, 6 and 18 months with changes in FE strength in the teriparatide-treated group, but not in the risedronate group. Conclusions Positive correlations between changes in a biochemical marker of bone formation and improvement of biomechanical properties support the use of PINP as a surrogate marker of bone strength in teriparatide-treated GIO patients.

High resolution quantitative computed tomography-based assessment of trabecular microstructure and strength estimates by finite-element analysis of the spine, but not DXA, reflects vertebral fracture status in men with glucocorticoid-induced osteoporosis

High-resolution quantitative computed tomography (HRQCT)-based analysis of spinal bone density and microstructure, finite element analysis (FEA), and DXA were used to investigate the vertebral bone status of men with glucocorticoid-induced osteoporosis (GIO). DXA of L1–L3 and total hip, QCT of L1–L3, and HRQCT of T12 were available for 73 men (54.6±14.0years) with GIO. Prevalent vertebral fracture status was evaluated on radiographs using a semi-quantitative (SQ) score (normal=0 to severe fracture=3), and the spinal deformity index (SDI) score (sum of SQ scores of T4 to L4 vertebrae). Thirty-one (42.4%) subjects had prevalent vertebral fractures. Cortical BMD (Ct.BMD) and thickness (Ct.Th), trabecular BMD (Tb.BMD), apparent trabecular bone volume fraction (app.BV/TV), and apparent trabecular separation (app.Tb.Sp) were analyzed by HRQCT. Stiffness and strength of T12 were computed by HRQCT-based nonlinear FEA for axial compression, anterior bending and axial torsion. In logistic regressions adjusted for age, glucocorticoid dose and osteoporosis treatment, Tb.BMD was most closely associated with vertebral fracture status (standardized odds ratio [sOR]: Tb.BMD T12: 4.05 [95% CI: 1.8–9.0], Tb.BMD L1–L3: 3.95 [1.8–8.9]). Strength divided by cross-sectional area for axial compression showed the most significant association with spine fracture status among FEA variables (2.56 [1.29–5.07]). SDI was best predicted by a microstructural model using Ct.Th and app.Tb.Sp (r2=0.57, p<0.001). Spinal or hip DXA measurements did not show significant associations with fracture status or severity. In this cross-sectional study of males with GIO, QCT, HRQCT-based measurements and FEA variables were superior to DXA in discriminating between patients of differing prevalent vertebral fracture status. A microstructural model combining aspects of cortical and trabecular bone reflected fracture severity most accurately.

Finite element analysis in asymptomatic, symptomatic, and ruptured abdominal aortic aneurysms: in search of new rupture risk predictors.

OBJECTIVES To compare biomechanical rupture risk parameters of asymptomatic, symptomatic and ruptured abdominal aortic aneurysms (AAA) using finite element analysis (FEA). STUDY DESIGN Retrospective biomechanical single center analysis of asymptomatic, symptomatic, and ruptured AAAs. Comparison of biomechanical parameters from FEA. MATERIALS AND METHODS From 2011 to 2013 computed tomography angiography (CTA) data from 30 asymptomatic, 15 symptomatic, and 15 ruptured AAAs were collected consecutively. FEA was performed according to the successive steps of AAA vessel reconstruction, segmentation and finite element computation. Biomechanical parameters Peak Wall Rupture Risk Index (PWRI), Peak Wall Stress (PWS), and Rupture Risk Equivalent Diameter (RRED) were compared among the three subgroups. RESULTS PWRI differentiated between asymptomatic and symptomatic AAAs (p < .0004) better than PWS (p < .1453). PWRI-dependent RRED was higher in the symptomatic subgroup compared with the asymptomatic subgroup (p < .0004). Maximum AAA external diameters were comparable between the two groups (p < .1355). Ruptured AAAs showed the highest values for external diameter, total intraluminal thrombus volume, PWS, RRED, and PWRI compared with asymptomatic and symptomatic AAAs. In contrast with symptomatic and ruptured AAAs, none of the asymptomatic patients had a PWRI value >1.0. This threshold value might identify patients at imminent risk of rupture. CONCLUSIONS From different FEA derived parameters, PWRI distinguishes most precisely between asymptomatic and symptomatic AAAs. If elevated, this value may represent a negative prognostic factor for asymptomatic AAAs.

Unfolding Feasible Arithmetic and Weak Truth

In this paper we continue Feferman’s unfolding program initiated in (Feferman, vol. 6 of Lecture Notes in Logic, 1996) which uses the concept of the unfolding U(S) of a schematic system S in order to describe those operations, predicates and principles concerning them, which are implicit in the acceptance of S. The program has been carried through for a schematic system of non-finitist arithmetic NFA in Feferman and Strahm (Ann Pure Appl Log, 104(1–3):75–96, 2000) and for a system FA (with and without Bar rule) in Feferman and Strahm (Rev Symb Log, 3(4):665–689, 2010). The present contribution elucidates the concept of unfolding for a basic schematic system FEA of feasible arithmetic. Apart from the operational unfolding U0(FEA) of FEA, we study two full unfolding notions, namely the predicate unfolding U(FEA) and a more general truth unfolding UT(FEA) of FEA, the latter making use of a truth predicate added to the language of the operational unfolding. The main results obtained are that the provably convergent functions on binary words for all three unfolding systems are precisely those being computable in polynomial time. The upper bound computations make essential use of a specific theory of truth TPT over combinatory logic, which has recently been introduced in Eberhard and Strahm (Bull Symb Log, 18(3):474–475, 2012) and Eberhard (A feasible theory of truth over combinatory logic, 2014) and whose involved proof-theoretic analysis is due to Eberhard (A feasible theory of truth over combinatory logic, 2014). The results of this paper were first announced in (Eberhard and Strahm, Bull Symb Log 18(3):474–475, 2012).

Finite Element Analysis Model of a Contactless Transformer for Battery Chargers in Electric Vehicles

A contactless transformer model is proposed in this paper using Finite Element Analysis (FEA). This model can be used to simulate Inductive Coupling Power Transfer (ICPT) systems with good accuracy of the transformer and reduce the fabrication time of these systems. The model not only takes into account the geometry of the windings but also the frequency effects in them. As the transformer does not have a magnetic core, it is complicated to model because the flux is expanded in the area around the windings. In order to obtain a very accurate model, it is necessary to use a 2D/3D field solver.

A survey of feature selection in Internet traffic characterization

In the last decade, the research community has focused on new classification methods that rely on statistical characteristics of Internet traffic, instead of pre-viously popular port-number-based or payload-based methods, which are under even bigger constrictions. Some research works based on statistical characteristics generated large fea-ture sets of Internet traffic; however, nowadays it?s impossible to handle hun-dreds of features in big data scenarios, only leading to unacceptable processing time and misleading classification results due to redundant and correlative data. As a consequence, a feature selection procedure is essential in the process of Internet traffic characterization. In this paper a survey of feature selection methods is presented: feature selection frameworks are introduced, and differ-ent categories of methods are briefly explained and compared; several proposals on feature selection in Internet traffic characterization are shown; finally, future application of feature selection to a concrete project is proposed.

UMA ANÁLISE DA RELAÇÃO ENTRE VARIÁVEIS MACROECONÔMICAS E O COMPORTAMENTO DAS AÇÕES DE MAIOR LIQUIDEZ DO ÍNDICE IBOVESPA

As ações de maior liquidez do índice IBOVESPA, refletem o comportamento das ações de um modo geral, bem como a relação das variáveis macroeconômicas em seu comportamento e estão entre as mais negociadas no mercado de capitais brasileiro. Desta forma, pode-se entender que há reflexos de fatores que impactam as empresas de maior liquidez que definem o comportamento das variáveis macroeconômicas e que o inverso também é uma verdade, oscilações nos fatores macroeconômicos também afetam as ações de maior liquidez, como IPCA, PIB, SELIC e Taxa de Câmbio. O estudo propõe uma análise da relação existente entre variáveis macroeconômicas e o comportamento das ações de maior liquidez do índice IBOVESPA, corroborando com estudos que buscam entender a influência de fatores macroeconômicos sobre o preço de ações e contribuindo empiricamente com a formação de portfólios de investimento. O trabalho abrangeu o período de 2008 a 2014. Os resultados concluíram que a formação de carteiras, visando a proteção do capital investido, deve conter ativos com correlação negativa em relação às variáveis estudadas, o que torna possível a composição de uma carteira com risco reduzido.

ANALISANDO A RELAÇÃO DOS VOLUMES DE EXPORTAÇÃO E DE IMPORTAÇÃO, PIB, TAXAS DE CÂMBIO E INFLAÇÃO NO PERÍODO DE 2004 A 2014.

Esta dissertação visa deslumbrar uma análise macroeconômica do Brasil, especialmente no que se refere à relação dos índices mensais dos volumes das exportações e das importações com os volumes mensais do PIB, da Taxa SELIC e as Taxas de Câmbio, conforme dados coletados no período de janeiro de 2004 a dezembro de 2014, através de pesquisa literária referente aos históricos sobre cada conceito envolvido no âmbito da macroeconomia das varáveis estudadas. Foi realizado um estudo de caso embasado em dados de sites governamentais, no período delimitado, empregando-se o método de regressão linear, com base na Teoria da correlação de Pearson, demonstrando os resultados obtidos no período do estudo para as varáveis estudadas. Desta maneira, conseguiu-se estudar e analisar como as variáveis dependentes (resposta): volume das exportações e volume das importações estão relacionadas com as varáveis independentes (explicativas): PIB, Taxa Selic e taxa de Câmbio. Os resultados apurados no presente estudo permitem identificar que existe correlação moderada e negativa, quando analisadas a Taxa Selic e a Taxa de Câmbio com os volumes das exportações e das importações, enquanto o PIB apresenta correlação forte e positiva na análise com os volumes das exportações e das importações

SONIA REGINA PRADO

A dissertação teve como objetivo principal estudar como uma Instituição de Ensino Superior Privada (IES) atuante no Brasil tem crescido pós Lei de Diretrizes e Bases (LDB) de 1996 até 2015, por meio da análise do curso de bacharelado em Administração de Empresas, nas modalidades: presencial, EAD e Flex (semipresencial). Para este fim, foi realizada uma pesquisa exploratória, de caráter qualitativo baseada no método do estudo de caso. Para coleta de evidências foram analisados relatórios corporativos (Annual Report, Relatórios Internos e outros documentos), entrevistas baseadas em roteiro semiestruturado com gestores da IES privada e observações. Dentre os principais achados, verificou-se que as principais estratégicas de crescimento da IES privada estudada se basearam em fusões e aquisições de outras IES, abertura de novos polos de EAD, na abertura de novas unidades próprias, bem como em inovações em várias dimensões da organização. Os programas governamentais de financiamento aos alunos também são fortes contribuintes para este crescimento, como o Fundo de Financiamento ao Estudante do Ensino Superior (FIES) e o Programa Universidade para Todos (Prouni). Com essa nova realidade, o ensino superior privado recebeu incentivo e facilitação para o seu crescimento, a um ritmo acelerado. Consequentemente pode-se concluir que a IES privada estudada adotou as seguintes estratégias de crescimento: Expansão orgânica com fusões/ aquisições de Instituições menores, com desenvolvimento de planos para todos os campi Brasil; Greenfield (por meio de solicitação de autorização de novas unidades e/ou cursos) em cidades sem possibilidades de aquisições/fusões, e aumentando o número de vagas/ matriculas nas unidades já existentes, aderiu aos programas do governo e também cuidou da evasão por meio de: Seguro educacional; gestão preparada para atender necessidades do discente; Sistema de Ensino com currículos integrados nacionalmente; Intercâmbio de alunos e professores entre as diversas unidades em todas as regiões do país e padronização dos processos.

Perspectivas em exercício: Uma investigação sobre a lógica administrativa e o engajamento subjetivo no trabalho

Esta pesquisa tem como tema os discursos que circulam e estruturam o ambiente de trabalho nas empresas. De forma geral, busca-se compreender a lógica administrativa que, no limite, exerce uma condução da subjetividade dos trabalhadores. Temos por objetivos: 1) identificar como nas escolas do pensamento administrativo do século XX o engajamento do trabalho é requerido dos trabalhadores; 2) pretendemos discutir uma possível caracterização do discurso e dos usos da administração, como campo de conhecimento sobre o trabalho, dentro das organizações. Para tanto, estabelecemos como panorama teórico-metodológico nas ideias centrais de Michel Foucault em suas análises sobre a funcionalidade do poder e seus dispositivos. Propusemos uma perspectiva arqueogenealógica para a estudar o tema trabalho por meio da lógica da administração e do engajamento. Para estruturar esta análise, selecionamos disciplinas oferecidas e examinamos ementas e referências de leituras nos cursos de graduação da Escola de Administração de Empresas de São Paulo da Fundação Getúlio Vargas (EAESP-FGV) e do curso de Administração da Faculdade de Economia, Administração e Contabilidade da Universidade de São Paulo (FEA-USP). Diante do contato com a discursividade administrativa pudemos formular algumas reflexões. A Administração de Empresas é a ciência da demonstração, pautada na dominação da realidade por uma dita eficiência. É o que se faz produtivo da realidade ou o que se produz nela que se torna científico. Não há discussão, nos registros aqui investigados, de um questionamento sobre o discurso de eficiência, de melhores práticas e da localização das organizações como construções historicamente produzidas, apenas como produtoras de determinações. Não parece haver a possibilidade de desnaturalizar a empresa. A administração parece estar pautada em uma duplicação da dominação como a profissão que é moldada ao moldar o trabalho. Partimos também da análise do que se nomeia engajamento para compreender o que é requerido do trabalhador para além do contrato de trabalho e de sua produtividade material. Neste sentido, o trabalho torna-se uma experiência de educação em contínua e ininterrupta vigilância pedagógica. O efeito moral das técnicas e das provas nas correntes de pensamento da administração permite uma condução técnica e do modo de viver dos trabalhadores. Nesse sentido, a administração, propõe o aperfeiçoamento do cuidado de si no trabalho e para o trabalho. As disciplinas então se duplicam: pelo exterior, por meio da regra pautada na estrutura formal da autoridade da fábrica/empresa com o governo dos corpos; e pelo interior por meio de uma sujeição por identidade, pela estilização da vida