A biomechanical investigation of dual growing rods used for fusionless scoliosis correction

Background The use of dual growing rods is a fusionless surgical approach to the treatment of early onset scoliosis (EOS), which aims of harness potential growth in order to correct spinal deformity. The purpose of this study was to compare the in-vitro biomechanical response of two different dual rod designs under axial rotation loading. Methods Six porcine spines were dissected into seven level thoracolumbar multi-segmental units. Each specimen was mounted and tested in a biaxial Instron machine, undergoing nondestructive left/right axial rotation to peak moments of 4Nm at a constant rotation rate of 8deg.s-1. A motion tracking system (Optotrak) measured 3D displacements of individual vertebrae. Each spine was tested in an un-instrumented state first and then with appropriately sized semi-constrained growing rods and ‘rigid’ rods in alternating sequence. Range of motion, neutral zone size and stiffness were calculated from the moment-rotation curves and intervertebral ranges of motion were calculated from Optotrak data. Findings Irrespective of test sequence, rigid rods showed significantly reduction of total rotation across all instrumented levels (with increased stiffness) whilst semi-constrained rods exhibited similar rotation behavior to the un-instrumented (P<0.05). An 11% and 8% increase in stiffness for left and right axial rotation respectively and 15% reduction in total range of motion was recorded with dual rigid rods compared with semi-constrained rods. Interpretation Based on these findings, the semi-constrained growing rods do not increase axial rotation stiffness compared with un-instrumented spines. This is thought to provide a more physiological environment for the growing spine compared to dual rigid rod constructs.

Comparison of eight published lumbar spine finite element models

Due to its ability to represent intricate systems with material nonlinearities as well as irregular loading, boundary, geometrical and material domains, the finite element (FE) method has been recognized as an important computational tool in spinal biomechanics. Current FE models generally account for a single distinct spinal geometry with one set of material properties despite inherently large inter-subject variability. The uncertainty and high variability in tissue material properties, geometry, loading and boundary conditions has cast doubt on the reliability of their predictions and comparability with reported in vitro and in vivo values. A multicenter study was undertaken to compare the results of eight well-established models of the lumbar spine that have been developed, validated and applied for many years. Models were subjected to pure and combined loading modes and their predictions were compared to in vitro and in vivo measurements for intervertebral rotations, disc pressures and facet joint forces. Under pure moment loading, the predicted L1-5 rotations of almost all models fell within the reported in vitro ranges; their median values differed on average by only 2° for flexion-extension, 1° for lateral bending and 5° for axial rotation. Predicted median facet joint forces and disc pressures were also in good agreement with previously published median in vitro values. However, the ranges of predictions were larger and exceeded the in vitro ranges, especially for facet joint forces. For all combined loading modes, except for flexion, predicted median segmental intervertebral rotations and disc pressures were in good agreement with in vivo values. The simulations yielded median facet joint forces of 0 N in flexion, 38 N in extension, 14 N in lateral bending and 60 N in axial rotation that could not be validated due to the paucity of in vivo facet joint forces. In light of high inter-subject variability, one must be cautious when generalizing predictions obtained from one deterministic model. This study demonstrates however that the predictive power increases when FE models are combined together. The median of individual numerical results can hence be used as an improved tool in order to estimate the response of the lumbar spine.

Excessive bone formation in a mouse model of ankylosing spondylitis is associated with decreases in Wnt pathway inhibitors

Introduction: Ankylosing spondylitis (AS) is unique in its pathology where inflammation commences at the entheses before progressing to an osteoproliferative phenotype generating excessive bone formation that can result in joint fusion. The underlying mechanisms of this progression are poorly understood. Recent work has suggested that changes in Wnt signalling, a key bone regulatory pathway, may contribute to joint ankylosis in AS. Using the proteoglycan-induced spondylitis (PGISp) mouse model which displays spondylitis and eventual joint fusion following an initial inflammatory stimulus, we have characterised the structural and molecular changes that underlie disease progression. Methods: PGISp mice were characterised 12 weeks after initiation of inflammation using histology, immunohistochemistry (IHC) and expression profiling. Results: Inflammation initiated at the periphery of the intervertebral discs progressing to disc destruction followed by massively excessive cartilage and bone matrix formation, as demonstrated by toluidine blue staining and IHC for collagen type I and osteocalcin, leading to syndesmophyte formation. Expression levels of DKK1 and SOST, Wnt signalling inhibitors highly expressed in joints, were reduced by 49% and 63% respectively in the spine PGISp compared with control mice (P < 0.05) with SOST inhibition confirmed by IHC. Microarray profiling showed genes involved in inflammation and immune-regulation were altered. Further, a number of genes specifically involved in bone regulation including other members of the Wnt pathway were also dysregulated. Conclusions: This study implicates the Wnt pathway as a likely mediator of the mechanism by which inflammation induces bony ankylosis in spondyloarthritis, raising the potential that therapies targeting this pathway may be effective in preventing this process.

Novel ANKH amino terminus mutation (Pro5Ser) associated with early-onset calcium pyrophosphate disease with associated phosphaturia

This report describes a 32-year-old woman presenting since childhood with progressive calcium pyrophosphate disease (CPPD), characterized by severe arthropathy and chondrocalcinosis involving multiple peripheral joints and intervertebral disks. Because ANKH mutations have been previously described in familial CPPD, the proband's DNA was assessed at this locus by direct sequencing of promoter and coding regions and revealed 3 sequence variants in ANKH. Sequences of exon 1 revealed a novel isolated nonsynonymous mutation (c.13 C>T), altering amino acid in codon 5 from proline to serine (CCG>TCG). Sequencing of parental DNA revealed an identical mutation in the proband's father but not the mother. Subsequent clinical evaluation demonstrated extensive chondrocalcinosis and degenerative arthropathy in the proband's father. In summary, we report a novel mutation, not previously described, in ANKH exon 1, wherein serine replaces proline, in a case of early-onset severe CPPD associated with metabolic abnormalities, with similar findings in the proband's father.

Investigating ANKH and ENPP1 in Slovakian families with chondrocalcinosis

Familial articular chondrocalcinosis (CC) was Wrst reported in 1963. It is characterised by multiple calciWcations of hyaline and Wbrous cartilage in the joints and intervertebral discs. Mutations in ANKH have been identified in several pedigrees as a monogenic cause for this disorder. ANKH is a key protein in pyrophosphate metabolism and is involved in pyrophosphate transport across the cell membrane. The objective of this work was to screen ANKH and ENPP1, two key genes in pyrophosphate metabolism, in Slovakian kindreds with familial CC. DNA samples from 25 individuals (10 aVected, 15 unaVected) from 8 families were obtained. The promoter, coding regions and intron-exon boundaries of ANKH and ENPP1 were sequenced. Twelve DNA sequence variants, six in each gene, were identiWed. All the variants had been previously identified. None segregated with the disease. Our results suggest that neither ANKH nor ENPP1 mutations are the cause of CC in these families, indicating that possibly other major genes are involved in the aethiopathogenesis of this condition in these families.

Socioeconomic Status, Occupational Factors and Lifestyle as Predictors of Hospitalisation for Back Disorders

The aim of this dissertation was to examine the determinants of severe back disorders leading to hospital admission in Finland. First, back-related hospitalisations were considered from the perspective of socioeconomic status, occupation, and industry. Secondly, the significance of psychosocial factors at work, sleep disturbances, and such lifestyle factors as smoking and overweight was studied as predictors of hospitalisation due to back disorders. Two sets of data were used: 1) the population-based data comprised all occupationally active Finns aged 25-64, and included hospitalisations due to back disorders in 1996 and 2) a cohort of employees followed up from 1973 to 2000 having been hospitalised due to back disorders. The results of the population-based study showed that people in physically strenuous industries and occupations, such as agriculture and manufacturing, were at an increased risk of being hospitalised for back disorders. The lowest hospitalisation rates were found in sedentary occupations. Occupational class and the level of formal education were independently associated with hospitalisation for back disorders. This stratification was fairly consistent across age-groups and genders. Men had a slightly higher risk of becoming hospitalised compared with women, and the risk increased with age among both genders. The results of the prospective cohort study showed that psychosocial factors at work such as low job control and low supervisor support predicted subsequent hospitalisation for back disorders even when adjustments were made for occupational class and physical workload history. However, psychosocial factors did not predict hospital admissions due to intervertebral disc disorders; only admissions due to other back disorders. Smoking and overweight predicted, instead, only hospitalisation for intervertebral disc disorders. These results suggest that the etiological factors of disc disorders and other back disorders differ from each other. The study concerning the association of sleep disturbances and other distress symptoms with hospitalisation for back disorders revealed that sleep disturbances predicted subsequent hospitalisation for all back disorders after adjustment for chronic back disorders and recurrent back symptoms at baseline, as well as for work-related load and lifestyle factors. Other distress symptoms were not predictive of hospitalisation.

Gravity-induced coronal plane joint moments in adolescent idiopathic scoliosis

Background Adolescent Idiopathic Scoliosis is the most common type of spinal deformity, and whilst the risk of progression appears to be biomechanically mediated (larger deformities are more likely to progress), the detailed biomechanical mechanisms driving progression are not well understood. Gravitational forces in the upright position are the primary sustained loads experienced by the spine. In scoliosis they are asymmetrical, generating moments about the spinal joints which may promote asymmetrical growth and deformity progression. Using 3D imaging modalities to estimate segmental torso masses allows the gravitational loading on the scoliotic spine to be determined. The resulting distribution of joint moments aids understanding of the mechanics of scoliosis progression. Methods Existing low-dose CT scans were used to estimate torso segment masses and joint moments for 20 female scoliosis patients. Intervertebral joint moments at each vertebral level were found by summing the moments of each of the torso segment masses above the required joint. Results The patients’ mean age was 15.3 years (SD 2.3; range 11.9 – 22.3 years); mean thoracic major Cobb angle 52° (SD 5.9°; range 42°-63°) and mean weight 57.5 kg (SD 11.5 kg; range 41 – 84.7 kg). Joint moments of up to 7 Nm were estimated at the apical level. No significant correlation was found between the patients’ major Cobb angles and apical joint moments. Conclusions Patients with larger Cobb angles do not necessarily have higher joint moments, and curve shape is an important determinant of joint moment distribution. These findings may help to explain the variations in progression between individual patients. This study suggests that substantial corrective forces are required of either internal instrumentation or orthoses to effectively counter the gravity-induced moments acting to deform the spinal joints of idiopathic scoliosis patients.

Inflammation-driven bone formation in a mouse model of ankylosing spondylitis: Sequential not parallel processes

Background Ankylosing spondylitis (AS) is an immune-mediated arthritis particularly targeting the spine and pelvis and is characterised by inflammation, osteoproliferation and frequently ankylosis. Current treatments that predominately target inflammatory pathways have disappointing efficacy in slowing disease progression. Thus, a better understanding of the causal association and pathological progression from inflammation to bone formation, particularly whether inflammation directly initiates osteoproliferation, is required. Methods The proteoglycan-induced spondylitis (PGISp) mouse model of AS was used to histopathologically map the progressive axial disease events, assess molecular changes during disease progression and define disease progression using unbiased clustering of semi-quantitative histology. PGISp mice were followed over a 24-week time course. Spinal disease was assessed using a novel semi-quantitative histological scoring system that independently evaluated the breadth of pathological features associated with PGISp axial disease, including inflammation, joint destruction and excessive tissue formation (osteoproliferation). Matrix components were identified using immunohistochemistry. Results Disease initiated with inflammation at the periphery of the intervertebral disc (IVD) adjacent to the longitudinal ligament, reminiscent of enthesitis, and was associated with upregulated tumor necrosis factor and metalloproteinases. After a lag phase, established inflammation was temporospatially associated with destruction of IVDs, cartilage and bone. At later time points, advanced disease was characterised by substantially reduced inflammation, excessive tissue formation and ectopic chondrocyte expansion. These distinct features differentiated affected mice into early, intermediate and advanced disease stages. Excessive tissue formation was observed in vertebral joints only if the IVD was destroyed as a consequence of the early inflammation. Ectopic excessive tissue was predominantly chondroidal with chondrocyte-like cells embedded within collagen type II- and X-rich matrix. This corresponded with upregulation of mRNA for cartilage markers Col2a1, sox9 and Comp. Osteophytes, though infrequent, were more prevalent in later disease. Conclusions The inflammation-driven IVD destruction was shown to be a prerequisite for axial disease progression to osteoproliferation in the PGISp mouse. Osteoproliferation led to vertebral body deformity and fusion but was never seen concurrent with persistent inflammation, suggesting a sequential process. The findings support that early intervention with anti-inflammatory therapies will be needed to limit destructive processes and consequently prevent progression of AS.

Proto-alphabetic inscriptions from the Wadi Arabah

Abstract: Three early West Semitic inscriptions from the Arabah valley are studied here, all of them apparently connected with the Egyptian copper-mining activity in the region, notably at Timna, in the period of the Ramessides. The most striking detail in these texts is a sign corresponding to an Egyptian hieroglyph (N6B ) which depicts two serpents guarding the sun-disc, and another with one serpent (N6 , ); these never appear on conventional tables of early alphabetic letters; this leads to a critical reappraisal of current identifications of the original picture-signs, and elaboration of a new system of interpreting early Canaanite inscriptions, involving recognition that the signs could sometimes stand for whole words and could also be used as rebuses.

Conductividad hidráulica en diferentes suelos en el departamento de Boaco

La erosión del suelo y los factores que en ella influyen han sido estudiados a nivel mundial, en Nicaragua la necesidad de reconocer la influencia e impacto de los factores que interviene en el proceso de erosión es de gran necesidad, tanto para la generación de tecnología propia para condiciones tropicales que permita la reducción del proceso de erosión y el aprovechamiento del agua. Así como, el análisis de las inadecuadas medidas y manejo de protección de los recursos suelo y agua que se implementan en la actualidad. La conductividad hidráulica es un factor importante que determina el movimiento del agua en el suelo, estrechando una íntima relación con el escurrimiento superficial. Este estudio tiene como objetivo evaluar el desempeño de la metodología del infiltrómetro de tensión de minidiscos, comparado con el infiltrómetro de doble cilindro para determinar la conductividad hidráulica (K) en condiciones de laderas en los municipios de Boaco y Santa Lucia. La obtención de conductividad hidráulica no saturada se realizo por medio de dos metodologías Ankenyet al; (1991) y Zhang (1997). La conductividad hidráulica a saturación se obtuvo mediante el infiltrómetro de doble cilindro utilizando la ecuación de Reynolds (2002). Los diversos valores obtenidos, remarcan el carácter variable de este parámetro. El doble cilindro presentó valores bajos si se comparan con los datos de la tensión más cercana a saturación. Los datos de conductividad generados por las ecuaciones de Ankeny y Zhang presentaron diferencias ya que los primeros fueron en promedio dos veces mayor. El método infiltrómetro de tensión de mini disco resulta ser más práctico en términos de su facilidad, tiempo, número de operarios, número de repeticiones, consumo de agua especialmente en zonas de difícil acceso y sobre todo que las pruebas son realizadas en condiciones naturales del suelo lo cual permite mayor confiabilidad del método.

Avaliação dos métodos para análise da microinfiltração marginal em restaurações de resina composta classe V in vitro

O objetivo deste estudo foi comparar os resultados da microinfiltração marginal obtidos por diferentes meios de aquisição de imagens e métodos de mensuração da penetração de prata em restaurações de resina composta classe V, in vitro. Dezoito pré-molares humanos hígidos, recém extraídos, foram divididos em três grupos, de acordo com o tipo de instrumento para preparação cavitária utilizado. Grupo 1: ponta diamantada número 3100, em alta rotação. Grupo 2: broca carbide número 330, em alta rotação. Grupo 3: ponta CVDentus código 82137, em aparelho de ultrassom. Foram realizados preparos cavitários padronizados (3x4x2mm) classe V nas faces vestibular e lingual de todos os dentes, com margens oclusais em esmalte e cervicais em dentina/cemento. As cavidades foram restauradas com o sistema adesivo Solobond M (VOCO) e resina composta Grandio (VOCO), a qual foi inserida e fotoativada em três incrementos. Os corpos de prova ficaram imersos em água destilada por 24h a 37oC; receberam acabamento e polimento com discos SofLex (3M) e foram novamente armazenados em água destilada, por sete dias. Posteriormente, as superfícies dentárias foram coberta com duas camadas de esmalte para unhas vermelho, exceto as áreas adjacentes às restaurações. Os espécimes ficaram imersos em solução aquosa de nitrato de prata a 50% por 24h e em solução fotorreveladora por 2h e foram seccionados no sentido vestíbulo-lingual, passando pelo centro das restaurações, com disco diamantado em baixa rotação. As amostras foram polidas em politriz horizontal e analisadas por diferentes métodos. À extensão da microinfiltração foi atribuído escores de 0 a 3 através de análises por meio de estereomicroscópio tradicional e com leds e microscópio ótico. As imagens obtidas na lupa com leds e no microscópio ótico tiveram as áreas infiltradas medidas através do software AxioVision. O teste χ2 de McNemar-Bowker revelou concordância estatística entre estereomicroscópio tradicional e o com leds (p=0,809) durante análises semiquantitativas. Porém, houve diferenças significantes entre microscópio ótico e estereomicroscópios (p<0,001). Houve boa correlação entre análises semiquantitativas e quantitativas de acordo com o teste de Spearmann (p<0,001). O teste de Kruskall-Wallis não revelou diferenças estatisticamente significantes (p=0,174) entre os grupos experimentais na análise quantitativa por microscópio ótico, em esmalte. Ao contrário do que se observa com a mesma em lupa (p<0,001). Conclui-se que o método de atribuição de escores comumente aplicado com a lupa nos estudos da microinfiltração marginal é uma opção confiável para análise da microinfiltração.

Disko-balaztaren fabrikazio prozesuaren deskribapena eta mekanizaziorako CAM bidezko programazioa

[EU]Lan honetan auto baten disko-balaztaren fabrikazio prozesua deskribatzen da, mekanizazio prozesuaren CAM bidezko programazioan sakonduz. Disko-balaztaren fabrikazioarekin hasi aurretik, informazio osagarri bezala, honek historian zehar izan duen garapena eta piezaren deskribapen zein funtzionamenduaren azalpena ematen dira. Jarraian, disko-balaztaren fabrikazioaren alderdi ezberdinak azaltzen dira, prozesu honek aurkezten dituen aukera desberdinak adieraziz. Azkenik, CAM bidezko programazioaren funtzionamendua erakusten da disko-balaztaren mekanizazio prozesurako aplikatuta.

A influência do corte com diferentes discos e velocidades na integridade dos espécimes e na resistência adesiva de uma cerâmica a um cimento resinoso dual em ensaio de microtração

Esta pesquisa estudou a influência de diferentes velocidades de corte e marcas de discos diamantados nos valores de resistência adesiva, durante a preparação dos espécimes a serem submetidos à microtração, e na integridade das amostras por meio do microscópio eletrônico de varredura (MEV). Vinte blocos da cerâmica à base de dissilicato de lítio (IPS e.max Press) foram unidos com cimento resinoso (Rely X ARC) a blocos de compósito (Z100), construídos incrementalmente. Foram seguidas as recomendações dos fabricantes no tratamento da superfície da cerâmica e aplicação do cimento resinoso. Após 24 horas em água destilada a 37C, os espécimes foram divididos em dois grupos de discos: marcas Buehler e Extec e subdivididos nas velocidades de 200rpm e 400rpm (B2; E2; B4 e E4, respectivamente). Cada espécime foi cortado em dois eixos perpendiculares para obtenção de palitos com área adesiva de 1,0mm. Para cada condição experimental, os palitos foram separados, aleatoriamente, 15 palitos para análise ao MEV e 30 palitos para serem submetidos à força de tração. As médias de resistência adesiva em MPa foram E4=20,312 ; B4= 24,2 11,3 ; B2= 25,2 9,0 e E2= 28,6 10,4. Na análise estatística, observou-se que os valores de resistência adesiva na velocidade de 200rpm foram significativamente maiores comparados a velocidade de 400rpm, independente do disco empregado. Ao MEV, observou-se melhor integridade dos palitos na velocidade de 200rpm com presença de trincas menos extensas nas bordas externas. Constatou-se também que o disco Extec na velocidade de 400rpm apresentou movimentos excêntricos ao corte e obteve-se maior número de perdas prematuras, uma diminuição significante na média da área total de união (p<0,05), além de diferença significativa nos valores de resistência comparada a velocidade de 200rpm. Concluiu-se que a utilização de diferentes velocidades e sua interação com o disco empregado interfere na integridade dos espécimes e nos valores de resistência adesiva, sendo mais acentuada ao se utilizar o disco da marca Extec.

Etos na poesia combatente de menestréis do rap: por uma análise das imagens discursivas no grito marginal do hip hop brasileiro

Este estudo tem como objetivo averiguar os efeitos de sentido produzidos por músicas de hip hop (movimento cultural cultivado nos guetos fluminenses), com base na análise de sua expressão verbal (rap) e em uma consideração experimental de capas de disco. Objetiva-se também investigar, no material artístico de Marcelo D2 e MV Bill, relações sociais engendradas por sujeitos da periferia, em espaços sociais antagônicos (centro e periferia). Para isso, exploramos uma Análise do Discurso de base enunciativa, enfatizando o conceito de etos discursivo, além de noções vinculadas à problemática da alteridade discursiva, a fim de que se analise o posicionamento de entes subjugados perante o descaso a que estão submetidos, e suas impressões sobre as imagens discursivas de marginalizadores. Buscamos apreender etos produzidos por sujeitos do rap, considerando a presença do Outro que fala nele/por ele (alteridade). Nossos procedimentos metodológicos apontam o que levou a considerar o hip hop, além da trajetória seguida na delimitação do corpus. Além disso, expõem-se os motivos que nos fizeram priorizar etos e alteridade discursiva. As análises buscam avaliações sobre a materialidade discursiva, que almejam extrair sentidos produzidos nos guetos. Como resultados, refletimos sobre aspectos inerentes ao contexto social fluminense, ao relacionamento entre sujeitos, lugares e práticas, para que se alarguem considerações sobre essas afinidades, inclusive na escola. Desse modo, ambicionamos que se aprimorem os debates sobre práticas de afirmação social de classes e, através de novas discussões, se intensifiquem as iniciativas sociopolíticas

Influência do acabamento e polimento na resistência à flexão de uma cerâmica odontológica

Avaliou-se a influência de dois sistemas de acabamento e polimento na resistência à flexão de uma cerâmica feldspática EX-3 (Noritake). Para isto, confeccionou-se blocos cerâmicos com medidas em conformidade com a ISO 6872/1995. Em seguida obteve-se o glaze natural. A padronização da rugosidade superficial foi conferida com auxílio de um rugosímetro, e os blocos foram então divididos em cinco grupos. O Grupo I (controle) foi testado com glaze. Para os testes realizados nos demais grupos, os blocos receberam um tratamento de asperização por meio de uma ponta diamantada 4137 (KG Sorensen). Em seguida foram polidos com diferentes protocolos. No grupo II, o sistema de polimento dura white (Shofu). No grupo III, o sistema de polimento dura white (shofu) associado a uma pasta diamantada aplicada com disco de feltro. No grupo IV o sistema de polimento Exa Cerapol (Edenta) e no grupo V, este mesmo sistema mais pasta diamantada aplicada com disco de feltro. Após os procedimentos de acabamento e polimento, foi avaliada a rugosidade conseguida (Ra), para se avaliar a eficácia dos métodos testados. A análise estatística por ANOVA (p ≤ 0,05) mostrou não haver diferença estatisticamente significante entre os grupos (G2=3,820,58; G3=3,550,61; G4=4,050,40; G5=3,950.47) . Feito isto, os corpos-de-prova foram submetidos a um ensaio mecânico de resistência à flexão em três pontos, e também neste caso, os resultados depois de tratados estatisticamente não demonstraram diferenças estatísticas entre os grupos glazeados e os grupos que receberam tratamento (G1=132,126,9 MPa; G2=123,317,4 MPa; G3=114,519,3 MPa; G4=104,211,9 MPa e G5=104,719,1 MPa) . Após a realização destas avaliações, tornou-se possível concluir que o uso dos sistemas de acabamento e polimento testados neste trabalho permite obter superfícies com rugosidade similar a obtida com o glaze natural e não interferem na resistência à flexão da cerâmica utilizada.