Integration of the Food Waste Disposer Unit to the Existing Sewage System

Among the numerous approaches to food waste treatment, the food waste disposers method (FWDs), as a newcomer, has become slowly accepted by the general public owing to the worries about its impact on the existing sewage system. This paper aims to justify the role of FWDs in the process of urbanization in order to better prepare a city to take good care of the construction of its infrastructure and the solid waste treatment. Both the literatures and the case study help to confirm that FWDs has no negative effects on the wastewater treatment plant and it is also environmental friendly by reducing the greenhouse gas emissions. In the case study, the Lappeenranta waste water treatment plant has been selected in order to figure out the possible changes to a WWTP following the integration of FWDs: the observation shows only minor changes take place in a WWTP, in case of 25% application, like BOD up 7%, TSS up 6% and wastewater flowrate up 6%, an additional sludge production of 200 tons per year and the extra yield of methane up to 10000m3 per year; however, when the utilization rate of FWD is over 75%, BOD, TSS, and wastewater flowrate will experience more significant changes, thus exerting much pressure on the existing WWTP. FWDs can only be used in residential areas or cities equipped with consummate drainage network within the service sphere of WWTP, therefore, the relevant authority or government department should regulate the installation frequency of FWDs, while promoting the accessory application of FWDs. In the meanwhile, WWTP should improve their treatment process in order to expand their capacity for sludge treatment so as to stay in line with the future development of urban waste management.

Waste Stream Investigation from Perspective of Changing Waste Legislation at Green Sand Foundries

The update of the Finnish legislation concerning waste was unavoidable, to comply with the European Union (EU) requirements defined in the EU-Directive on Waste. The new waste law updates were enacted into the Finnish legislation on the 11.03.2011 and targeted for applicability by the 11.03.2012. This thesis investigates the implications of the new amendments to the waste legislation from the perspective of green sand foundries. The investigations are conducted by comparing two of Componenta’s green sand foundries and evaluating their waste streams. Additionally, the impacts of legislation amendments are critiqued on their environmental and economic aspects. The study’s comparison of waste fractions at the two foundries reveals that sand is dominant in absolute tonnage and costs. The increments of waste taxes forces foundries to focus on waste management, recycling and disposing. The new legislation’s promotion of material efficiency, also guides foundries towards the prevention of waste. A potential preventive measure is to regenerate waste sand resulting to cost savings on both raw-materials and waste management. However, the lack of absolute targets for waste prevention or recycling rates discourages the interests towards creating or adopting new technologies and methods for the waste handling.

Current status of the waste-to-energy chain in the County of North Savo, Finland

The aim of this report is to describe the current status of the waste-to-energy chain in the province of Northern Savonia in Finland. This work is part of the Baltic Sea Region Programme project Remowe-Regional Mobilizing of Sustainable Waste-to-Energy Production (2009-2012). Partnering regions across Baltic Sea countries have parallelly investigated the current status, bottle-necks and needs for development in their regions. Information about the current status is crucial for the further work within the Remowe project, e.g. in investigating the possible future status in target regions. Ultimate result from the Northern Savonia point of view will be a regional model which utilizes all available information and facilitates decision-making concerning energy utilization of waste. The report contains information on among others: - waste management system (sources, amounts, infrastructure) - energy system (use, supply, infrastructure) - administrative structure and legislation - actors and stakeholders in the waste-to-energy field, including interest and development ideas The current status of the regions will be compared in a separate Remowe report, with the focus on finding best practices that could be transferred among the regions. In this report, the current status has been defined as 2006-2009. In 2009, the municipal waste amount per capita was 479 kg/inhabitant in Finland. Industrial waste amounted 3550 kg/inhabitant, respectively. The potential bioenergy from biodegradable waste amounts 1 MWh/inhabitant in Northern Savonia. This figure includes animal manure, crops that would be suitable for energy use, sludge from municipal sewage treatment plants and separately collected biowaste. A key strategy influencing also to Remowe work is the waste plan for Eastern Finland. Currently there operate two digestion plants in Northern Savonia: Lehtoniemi municipal sewage treatment sludge digestion plant of Kuopion Vesi and the farm-scale research biogas plant of Agrifood Research Finland in Maaninka. Moreover, landfill gas is collected to energy use from Heinälamminrinne waste management centre and Silmäsuo closed landfill site, both belonging to Jätekukko Oy. Currently there is no thermal utilization of waste in Northern Savonia region. However, Jätekukko Oy is pretreating mixed waste and delivering refuse derived fuel (RDF) to Southern Finland to combustion. There is a strong willingness among seven regional waste management companies in Eastern Finland to build a waste incineration plant to Riikinneva waste management centre near city of Varkaus. The plant would use circulating fluidized bed (CFB) boiler. This would been a clear boost in waste-to-energy utilization in Northern Savonia and in many surrounding regions.

Feasibility of ASH DEC‐ process in treating sewage sludge and manure ash in Finland

In Finland the thermal treatment of sewage sludge has been moderate in 21th century. The reason has been the high moisture content of sludge. During 2005-2008, 97-99% of sewage sludge was utilized in landscaping and agriculture. However agricultural use has been during 2005-2007 less than 3 %. The aim of national waste management plan is that by 2016 100% of sludge is used either as soil amendment or energy. The most popular utilization method for manure is spreading it on arable land. The dry manures such as poultry manure and horse manure could also be used in incineration. The ashes could be used as fertilizers and while it is not suitable as a starter fertilizer, it is suitable in maintaining P levels in the soil. One of the main drivers for more efficient nutrient management is the eutrophication in lakes and the Baltic See. ASH DEC process can be used in concentrating phosphorus rich ashes while separating the heavy metals that could be included. ASH DEC process uses thermochemical treatment to produce renewable phosphate for fertilizer production. The process includes mixing of ashes and chlorine donors and subsequent treatment in rotary kiln for 20 min in temperature of 900 – 1 050 oC. The heavy metals evaporate and P-rich product is obtained. The toxic substances are retained in air pollution control system in form of mixed metal hydroxides. The aim of conducting this study is to estimate the potential of ASH DEC process in treating phosphorus rich ashes in Finland. The masses considered in are sewage sludge, dry manure from horses, and poultry and liquid pig manure. To date the usual treatment method for sewage sludge in Finland is composting or anaerobic digestion. Part of the amount of produced sewage sludge (800 kt/a fresh mass and 160 kt/a TS) could also be incinerated and the residual ashes used in ASH DEC process. Incinerating only manure can be economically difficult to manage because the incineration of manure is in Finland considered as waste incineration. Getting a permit for waste incineration is difficult and also small scale waste incineration is too expensive. The manure could act as an additional feedstock in counties with high density of animal husbandry where the land area might not be enough for spreading of manure. Now when the manure acts as a supplementary feedstock beside sludge, the ash can’t be used directly as fertilizer. Then it could be used in ASH DEC process. The perquisite is that the manure producers could pay for the incineration, which might prove problematic.

Kuivajätehuollon hiilijalanjälki ja kustannukset sekä kuljetusten kilpailutus – Etelä-Karjalan aluekeräyspisteverkoston päivitys

Tutkimuksen tavoitteena oli yhtenäistää Etelä-Karjalan alueen erilaisia tapoja toimia alueke-räyksen suhteen. Aluekeräyksellä tarkoitetaan jätteiden keräystä pisteiltä, joihin kotitaloudet, jotka eivät kuulu kiinteistökohtaiseen keräykseen, voivat tuoda syntypaikkalajitellun kuiva- eli sekajätteensä. Tavoitteena oli myös saada tietoa siitä, minkälaiset ovat eri kuivajätehuoltovaihtoehtojen ilmastonmuutos- ja kustannusvaikutukset. Lisäksi tavoitteena oli selvittää, miten ympäristönäkökohdat voidaan ottaa huomioon kuljetuskilpailutuksissa. Tutkimuksessa kerättiin tietoa internetistä, opinnäytetöistä ja tieteellisistä artikkeleista sekä yritysten edustajilta. Kasvihuonekaasupäästöjen laskennassa hyödynnettiin GaBi 6.0 -elinkaariarviointiohjelmaa. Tutkimuksen perusteella aluekeräyspisteet kannattaa sijoittaa reiteille, joita asukkaat käyttävät vähintään kerran viikossa ja mitkä ovat optimaalisesti myös kuljetusurakoitsijan kannalta. Taajama-alueelle ei nähty suositeltavaksi sijoittaa aluekeräyspisteitä. Suositeltavina astioina aluekeräyspisteille nähtiin syväkeräyssäiliöt, joiden tyhjennys onnistuu samalla keräyskalustolla kuin kiinteistöjen jäteastioiden, kun ajoneuvo on varustettu puominosturilla. Suositeltavaksi nähtiin myös harventaa jäteastioiden talvityhjennystiheyksiä, jos tyhjennystiheys on vakio ympäri vuoden, sillä pääosa aluekeräyspisteiden käyttäjistä on loma-asukkaita. Tyhjennystiheyksien harvennuksella olisi mahdollista saavuttaa kustannussäästöjä. Tutkimuksessa laskettiin kuivajätteen elinkaarenaikaisia kasvihuonekaasupäästöjä kuivajätteen keräyksestä loppusijoitukseen ja energiahyötykäyttöön. Energiahyötykäyttökohteiksi valittiin Riihimäen, Kotkan sekä Leppävirran (suunnitteilla) jätteenpolttolaitokset. Tulosten pohjalta kuivajätteen energiahyötykäyttö oli loppusijoitusta selkeästi parempi vaihtoehto. Kuivajätteen keräys- ja kuljetuspäästöjen vaikutus oli pieni. Kuivajätteen kuljetusmatkan pituus jätteenpolttolaitokselle ei ole siis ratkaisevassa roolissa kokonaiskasvihuonekaasupäästöjä tarkasteltaessa. Etäisyyttä suurempi vaikutus onkin kuivajätteen koostumuksella, polttolaitosten vuosihyötysuhteilla ja korvattavilla polttoaineilla. Jatkossa suositellaan selvittämään vielä vaihtoehtoisia käsittelytapoja kuivajätteen sisältämälle sekamuovijakeelle, jonka poltosta aiheutuu merkittävä osuus (noin 74 %) kuivajätteen polton kasvihuonekaasupäästöistä. Ajankohtaisia kuljetuskilpailutuksia varten tarkasteltiin vielä tarkemmin keräys- ja kuljetuspäästöjä. Tulosten pohjalta havaittiin, että keräys- ja kuljetuspäästöjä on mahdollista vähentää reilusti (46–74 %) siirtymällä dieselistä biopolttoaineiden käyttöön. Tuloksiin vaikuttaa kuitenkin merkittävästi, minkälaisista raaka-aineista biopolttoaineet on valmistettu. Kuivajätteen keräyspäästöjä on mahdollista pienentää myös päivittämällä aluekeräyspisteverkostoa. Tutkimuksessa tarkasteltiin kustannuksia aluekeräyspisteiden astioiden uusinnasta tai korjauksesta kuivajätteen loppusijoitukseen tai energiahyötykäyttöön asti. Merkittävimmät kustannukset aiheutuivat kuivajätteen loppusijoituksesta, energiahyötykäytöstä sekä keräyksestä. Kustannusten näkökulmasta keräyksen rooli oli siis suurempi. Työn lopussa annettiin vielä vinkkejä, joiden avulla jätehuoltoyritykset voivat tehdä jätekuljetushankintoja ympäristönäkökohdat huomioiden. Usein selkein tapa huomioida ympäristönäkökohdat kuljetuskilpailutuksissa on asettaa riittävän tiukkoja pakollisia vaatimuksia, jolloin voi valita hinnaltaan halvimman vaihtoehdon. Kuljetuspalvelun hankinnassa tulee huomioida ainakin energiankulutus, hiilidioksidi-, typenoksidi-, hiilivety- ja hiukkaspäästöt. Lainsäädäntö ei määrää vähimmäistasoja, vaan hankintaa tehdessä kannattaa kartoittaa markkinatilanne, jotta vaatimukset osaa asettaa oikealle tasolle. Markkinoille kannattaa myös tiedottaa tulevaisuuden tarpeista ja suunnitelmista. Suuria hankintakokonaisuuksia suositellaan pilkottavan pienempiin osiin, jotta pienet ja keskisuuret yritykset pystyvät myös osallistumaan tarjouskilpailuihin. Kannustus innovaatioiden huomioimiseen hankinnoissa on lisääntynyt myös jätehuollon alalla. Selvitettyjen kasvihuonekaasupäästöjen perusteella oli merkille pantavaa, miten suuri vaikutus polttolaitoksen valinnalla oli kasvihuonekaasupäästöihin. Oleellista onkin huomioida ympäristönäkökohdat myös energiahyötykäyttökohdetta valittaessa.

Decentralized management of organic household wastes in the Kathmandu Valley using small-scale composting reactors

The sustainable management of municipal solid waste in the Kathmandu Valley has always been a challenging task. Solid waste generation has gone rapidly high in the Kathmandu Valley over the last decade due to booming population and rapid urbaniza-tion. Finding appropriate landfill sites for the disposal of solid wastes generated from the households of the Kathmandu Valley has always been a major problem for Nepalese government. 65 % of total generated wastes from the households of Nepal consist of organic materials. As large fractions of generated household wastes are organic in na-ture, composting can be considered as one of the best sustainable ways to recycle organ-ic wastes generated from the households of Nepal. Model Community Society Development (MCDS), a non-governmental organization of Nepal carried out its small-scale project in five households of the Kathmandu Valley by installing composting reactors. This thesis is based on this small-scale project and has used secondary data provided by MCDS Nepal for carrying out the study. Proper man-agement of organic wastes can be done at household levels through the use of compost-ing reactors. The end product compost can be used as soil conditioners for agricultural purposes such as organic farming, roof-top farming and gardening. The overall average organic waste generation in the Kathmandu Valley is found to be 0,23 kg/person/day and the total amount of organic household wastes generated in the Kathmandu Valley is around 210 Gg/yr. Produced composts from five composting reac-tors contain high amount of moistures but have sufficient amount of nutrients required for the fertility of land and plant growth. Installation of five composting reactors in five households have prevented 2,74 Mg of organic wastes going into the landfills, thus re-ducing 107 kg of methane emissions which is equivalent to 2,7 Mg of carbondioxide.

Sahateollisuuden jätteiden hyötykäyttö menetelmät ja viranomaisraportoinnin kehittäminen

Yritysten ympäristönsuojelua ohjailevat kansalliset lait ja asetukset kuten ympäristönsuojelulaki (86/2000) ja jätelaki (646/2011) sekä Euroopan unionin lainsäädäntö. Ympäristönsuojelu on yrityksille yhä tärkeämpi osa liiketoimintaa. Tähän ovat vaikuttaneet yhä enemmän kiristynyt lainsäädäntö ja taloudellisen hyödyn tavoittelu ympäristöasioiden hyvän hoidon seurauksena sekä sidosryhmien lisääntynyt kiinnostus yritysten ympäristöasioista. Diplomityön tavoitteena oli perehtyä uuden jätelain tuomiin muutoksiin sahateollisuuden osalta, selvittää sahateollisuuden jätteiden hyötykäyttö mahdollisuuksia yleisesti sekä kehittää viranomaisraportointia jätteiden osalta. Diplomityössä analysoidaan Kiteen sahan jätevirtoja ja niiden käsittelyä, sekä hyötykäyttöä. Tarkoituksena on pyrkiä tilanteeseen, jossa syntyvät jätteet käsiteltäisiin siten, että jätteiden käsittelystä aiheutuvat kustannukset pienenisivät ja kaatopaikalle sijoitettavan jätteen määrä vähenisi ilman investointien tarvetta. Työssä vertaillaan muiden Stora Enson Suomen sahojen jätevirtoja ja niiden hyötykäyttöä Kiteen sahan tilanteeseen. Tavoitteena on löytää sellaisia jätteiden hyötykäyttömahdollisuuksia, jotka olisivat hyödynnettävissä kaikilla Stora Enson Suomen sahoilla.

Promoting Cleantech in Emerging Markets: Business Model for Waste Pre-treatment Equipment in China

Waste incineration is becoming increasingly widespread method of waste disposal in China. Incineration plants mostly use grate and circular fluidized bed (CFB) technology. Waste combustion in cement production is also beginning to gradually increase. However, Chinese waste composition is causing problems for the energy utilization. Mechanical waste pre-treatment optimizes the combustion process and facilitates the energy recovery. The objective of this study is to identify how Western waste pre-treatment manufacturer could operate in Chinese markets. Chinese waste management industry is reviewed via PESTEL analysis. The current state and future predictions of grate and CFB incineration as well as cement manufacturing are monitored. Grate combustion, which requires lesser waste pre-treatment, is becoming more common at the expense of CFB incineration in China. The most promising future for waste treatment is in cement production industry. Waste treatment equipment manufacturer should try to create pilot projects with biggest cement producers with a view of growing co-operation in the future.

Isolation and characterization of bacterial strains with a hydrolytic profile with potential use in bioconversion of agroindustial by-products and waste

There is a trend towards the use of novel technologies nowadays, mainly focused on biological processes, for recycling and the efficient utilization of organic residues that can be metabolized by different microorganisms as a source of energy. In the present study the isolation of bacterial strains from six different agro-industrial by-products and waste was performed with the objective of evaluating their hydrolytic capacities and suitability for use in bioconversion of specific substrates. The 34 isolated strains were screened in specific culture media for the production of various hydrolytic enzymes (lipase, protease, cellulase, and amylase). It was found that 28 strains exhibited proteolytic activity, 18 had lipolytic activity, 13 had caseinolytic activity, 15 had amylolytic activity, and 11 strains exhibited cellulolytic activity. The strains that showed the highest hydrolytic capacities with biotechnological potential were selected, characterized genotipically, and identified as Bacillus, Serratia, Enterococcus, Klebsiella, Stenotrophomonas, Lactococcus, and Escherichia genera. It was concluded that the strain isolates have a high potential for use in the bioconversion of agro-industrial waste, both as a pure culture and as a microbial consortium.

Potential of energy and nutrient recovery from biodegradable waste by co-treatment in Lithuania

Biodegradable waste quantities in Lithuania and their potential for the co-treatment in renewable energy and organic fertilizer production are investigated. Two scenarios are formulated to study the differences of the amounts of obtainable energy and fertilizers between different ways of utilization. In the first scenario, only digestion is used, and in the second scenario, other materials than straw are digested, and straw and the solid fraction of sewage sludge digestate are combusted. As a result, the amounts of heat and electricity, as well as the fertilizer amounts in the counties are obtained for both scenarios. Based on this study, the share of renewable energy in Lithuania could be doubled by the co-treatment of different biodegradable materials.

L'application du principe du pollueur-payeur à la gestion du risque environnemental et à la mutualisation des coûts de la pollution

Le but de cette étude est de déterminer qui paie pour le risque de pollution et par conséquent de vérifier si le principe du pollueur-payeur est effectivement mis en œuvre dans le domaine de la gestion du risque environnemental. Il s’agit d’examiner le degré de mutualisation de la gestion du risque dans différentes législations particulière. Les payeurs peuvent a priori se classer dans quatre catégories : les personnes dont l’activité contribue au risque de pollution, les compagnies d’assurance qui acceptent d’assurer ces personnes, les organismes ou autorités publics et les tiers. Divers exemples issus de la législation belge ou européenne seront examinés afin de déterminer s’ils sont conformes à la lettre et/ou à l’esprit du principe pollueur-payeur. Il s’agit notamment de la responsabilité civile, de la responsabilité environnementale, de la gestion des déchets et du marché de quotas d’émissions de gaz à effet de serre. Les techniques de responsabilité qui interviennent après que le dommage ait lieu et requièrent la démonstration de l’existence d’un lien de causalité ne permettent pas toujours d’assurer pleinement la fonction préventive du principe du pollueur-payeur. Elles ne constituent pas des instruments adéquats de gestion de la pollution diffuse ou chronique. En conséquence, des techniques de mutualisation de la gestion du risque environnemental se sont développées. Le recours à ces techniques de mutualisation (par le recours à l’assurance, aux fonds publics financés par la fiscalité environnementale ou aux marchés de droit d’émissions) est-il conforme au principe pollueur-payeur et permet-il d’atteindre l’objectif d’un niveau élevé de protection de l’environnement ? L’effet dissuasif du principe pollueur-payeur n’est-il pas amoindri par la mutualisation ? L’article montre que la définition du principe pollueur-payeur par la Cour de Justice de l’Union européenne est centrée sur la contribution au risque de pollution ce qui permet de recourir aux techniques de mutualisation de la gestion du risque tout en respectant le Traité sur le fonctionnement de l’Union européenne. 

A Study of Single Stage Semi‐Dry Anaerobic Digestion of Organic Fraction of Municipal Solid Waste

Solid waste generation is a natural consequence of human activity and is increasing along with population growth, urbanization and industrialization. Improper disposal of the huge amount of solid waste seriously affects the environment and contributes to climate change by the release of greenhouse gases. Practicing anaerobic digestion (AD) for the organic fraction of municipal solid waste (OFMSW) can reduce emissions to environment and thereby alleviate the environmental problems together with production of biogas, an energy source, and digestate, a soil amendment. The amenability of substrate for biogasification varies from substrate to substrate and different environmental and operating conditions such as pH, temperature, type and quality of substrate, mixing, retention time etc. Therefore, the purpose of this research work is to develop feasible semi-dry anaerobic digestion process for the treatment of OFMSW from Kerala, India for potential energy recovery and sustainable waste management. This study was carried out in three phases in order to reach the research purpose. In the first phase, batch study of anaerobic digestion of OFMSW was carried out for 100 days at 32°C (mesophilic digestion) for varying substrate concentrations. The aim of this study was to obtain the optimal conditions for biogas production using response surface methodology (RSM). The parameters studied were initial pH, substrate concentration and total organic carbon (TOC). The experimental results showed that the linear model terms of initial pH and substrate concentration and the quadratic model terms of the substrate concentration and TOC had significant individual effect (p < 0.05) on biogas yield. However, there was no interactive effect between these variables (p > 0.05). The optimum conditions for maximizing the biogas yield were a substrate concentration of 99 g/l, an initial pH of 6.5 and TOC of 20.32 g/l. AD of OFMSW with optimized substrate concentration of 99 g/l [Total Solid (TS)-10.5%] is a semi-dry digestion system .Under the optimized condition, the maximum biogas yield was 53.4 L/kg VS (volatile solid).. In the second phase, semi-dry anaerobic digestion of organic solid wastes was conducted for 45 days in a lab-scale batch experiment for substrate concentration of 100 g/l (TS-11.2%) for investigating the start-up performances under thermophilic condition (50°C). The performance of the reactor was evaluated by measuring the daily biogas production and calculating the degradation of total solids and the total volatile solids. The biogas yield at the end of the digestion was 52.9 L/kg VS for the substrate concentration of 100 g/l. About 66.7% of volatile solid degradation was obtained during the digestion. A first order model based on the availability of substrate as the limiting factor was used to perform the kinetic studies of batch anaerobic digestion system. The value of reaction rate constant, k, obtained was 0.0249 day-1. A laboratory bench scale reactor with a capacity of 36.8 litres was designed and fabricated to carry out the continuous anaerobic digestion of OFMSW in the third phase. The purpose of this study was to evaluate the performance of the digester at total solid concentration of 12% (semi-dry) under mesophlic condition (32°C). The digester was operated with different organic loading rates (OLRs) and constant retention time. The performance of the reactor was evaluated using parameters such as pH, volatile fatty acid (VFA), alkalinity, chemical oxygen demand (COD), TOC and ammonia-N as well as biogas yield. During the reactor’s start-up period, the process is stable and there is no inhibition occurred and the average biogas production was 14.7 L/day. The reactor was fed in continuous mode with different OLRs (3.1,4.2 and 5.65 kg VS/m3/d) at constant retention time of 30 days. The highest volatile solid degradation of 65.9%, with specific biogas production of 368 L/kg VS fed was achieved with OLR of 3.1 kg VS/m3/d. Modelling and simulation of anaerobic digestion of OFMSW in continuous operation is done using adapted Anaerobic Digestion Model No 1 (ADM1).The proposed model, which has 34 dynamic state variables, considers both biochemical and physicochemical processes and contains several inhibition factors including three gas components. The number of processes considered is 28. The model is implemented in Matlab® version 7.11.0.584(R2010b). The model based on adapted ADM1 was tested to simulate the behaviour of a bioreactor for the mesophilic anaerobic digestion of OFMSW at OLR of 3.1 kg VS/m3/d. ADM1 showed acceptable simulating results.

Plan de negocio Gree-Waste

El crecimiento apresurado de la industria tecnológica en los últimos años a nivel mundial, ha generado un nuevo problema socio-ambiental: el manejo y control de los volúmenes de aparatos y componentes electrónicos obsoletos que crecen exponencialmente, específicamente los aparatos que provienen de sistemas de informática, volviéndose en una situación descontrolada y desatendida. Esta problemática empeora cada día por el desconocimiento, la imprudencia, las malas políticas adoptadas por el gobierno y el constante deseo de los consumidores por estar en contacto con los últimos modelos del mercado, reflejándose en un incremento acelerado en las ventas de aparatos electrónicos. Sin embargo, muchos se preguntaran él porque proponemos una idea de negocio caracterizada por lo social y lo ambiental, pues dicha idea viene de la experiencia que se ha tenido durante 7 años en el mercado de tecnología en computación y periféricos, que ha logrado una relación directa con empresas y personas; observando así, las verdaderas preocupaciones de los clientes y a su vez un aumento acelerado en los desechos tecnológicos. De esta manera y siguiendo con el espíritu emprendedor que nos ha caracterizado desde pequeños, hemos llegado a pensar en una idea de negocio interesante y viable, que nos permita incursionar ante competidores importantes y sobresaliendo con una idea innovadora que no se maneja de lleno en dicho sector. Para lograrlo, aprovecharemos los conocimientos y la experiencia que hemos acumulado a través de los años con el contacto directo con los clientes, quienes consideramos son el motor del negocio y llevándonos a concluir con el transcurrir del tiempo, que en Colombia no existe una cultura para desechar los elementos tecnológicos de una manera ecológica y saludable con el medio ambiente. Gracias a la oportunidad latente que muestra el mercado en el sector de reciclaje de desechos tecnológicos, nuestro equipo de trabajo se muestra inquieto ante la oportunidad de negocio encontrada, debido a que en Colombia existen pocas organizaciones que se especialicen en el proceso de reciclaje y reutilización adecuada de dichos desechos. Por esta razón, se confirma la oportunidad para generar un completo plan de negocio que gire en torno al manejo de e-waste y cuidado del medio ambiente, mediante la implementación de productos y servicios especializados para la recolección de dichos desechos electrónicos tanto para los consumidores como para las empresas.

Estudio de la aplicación de sistemas basados en el conocimiento a la operación de una planta de tratamiento de residuos sólidos urbanos por valorización energética

Una de las actuaciones posibles para la gestión de los residuos sólidos urbanos es la valorización energética, es decir la incineración con recuperación de energía. Sin embargo es muy importante controlar adecuadamente el proceso de incineración para evitar en lo posible la liberación de sustancias contaminantes a la atmósfera que puedan ocasionar problemas de contaminación industrial.Conseguir que tanto el proceso de incineración como el tratamiento de los gases se realice en condiciones óptimas presupone tener un buen conocimiento de las dependencias entre las variables de proceso. Se precisan métodos adecuados de medida de las variables más importantes y tratar los valores medidos con modelos adecuados para transformarlos en magnitudes de mando. Un modelo clásico para el control parece poco prometedor en este caso debido a la complejidad de los procesos, la falta de descripción cuantitativa y la necesidad de hacer los cálculos en tiempo real. Esto sólo se puede conseguir con la ayuda de las modernas técnicas de proceso de datos y métodos informáticos, tales como el empleo de técnicas de simulación, modelos matemáticos, sistemas basados en el conocimiento e interfases inteligentes. En [Ono, 1989] se describe un sistema de control basado en la lógica difusa aplicado al campo de la incineración de residuos urbanos. En el centro de investigación FZK de Karslruhe se están desarrollando aplicaciones que combinan la lógica difusa con las redes neuronales [Jaeschke, Keller, 1994] para el control de la planta piloto de incineración de residuos TAMARA. En esta tesis se plantea la aplicación de un método de adquisición de conocimiento para el control de sistemas complejos inspirado en el comportamiento humano. Cuando nos encontramos ante una situación desconocida al principio no sabemos como actuar, salvo por la extrapolación de experiencias anteriores que puedan ser útiles. Aplicando procedimientos de prueba y error, refuerzo de hipótesis, etc., vamos adquiriendo y refinando el conocimiento, y elaborando un modelo mental. Podemos diseñar un método análogo, que pueda ser implementado en un sistema informático, mediante el empleo de técnicas de Inteligencia Artificial.Así, en un proceso complejo muchas veces disponemos de un conjunto de datos del proceso que a priori no nos dan información suficientemente estructurada para que nos sea útil. Para la adquisición de conocimiento pasamos por una serie de etapas: - Hacemos una primera selección de cuales son las variables que nos interesa conocer. - Estado del sistema. En primer lugar podemos empezar por aplicar técnicas de clasificación (aprendizaje no supervisado) para agrupar los datos y obtener una representación del estado de la planta. Es posible establecer una clasificación, pero normalmente casi todos los datos están en una sola clase, que corresponde a la operación normal. Hecho esto y para refinar el conocimiento utilizamos métodos estadísticos clásicos para buscar correlaciones entre variables (análisis de componentes principales) y así poder simplificar y reducir la lista de variables. - Análisis de las señales. Para analizar y clasificar las señales (por ejemplo la temperatura del horno) es posible utilizar métodos capaces de describir mejor el comportamiento no lineal del sistema, como las redes neuronales. Otro paso más consiste en establecer relaciones causales entre las variables. Para ello nos sirven de ayuda los modelos analíticos - Como resultado final del proceso se pasa al diseño del sistema basado en el conocimiento. El objetivo principal es aplicar el método al caso concreto del control de una planta de tratamiento de residuos sólidos urbanos por valorización energética. En primer lugar, en el capítulo 2 Los residuos sólidos urbanos, se trata el problema global de la gestión de los residuos, dando una visión general de las diferentes alternativas existentes, y de la situación nacional e internacional en la actualidad. Se analiza con mayor detalle la problemática de la incineración de los residuos, poniendo especial interés en aquellas características de los residuos que tienen mayor importancia de cara al proceso de combustión.En el capítulo 3, Descripción del proceso, se hace una descripción general del proceso de incineración y de los distintos elementos de una planta incineradora: desde la recepción y almacenamiento de los residuos, pasando por los distintos tipos de hornos y las exigencias de los códigos de buena práctica de combustión, el sistema de aire de combustión y el sistema de humos. Se presentan también los distintos sistemas de depuración de los gases de combustión, y finalmente el sistema de evacuación de cenizas y escorias.El capítulo 4, La planta de tratamiento de residuos sólidos urbanos de Girona, describe los principales sistemas de la planta incineradora de Girona: la alimentación de residuos, el tipo de horno, el sistema de recuperación de energía, y el sistema de depuración de los gases de combustión Se describe también el sistema de control, la operación, los datos de funcionamiento de la planta, la instrumentación y las variables que son de interés para el control del proceso de combustión.En el capítulo 5, Técnicas utilizadas, se proporciona una visión global de los sistemas basados en el conocimiento y de los sistemas expertos. Se explican las diferentes técnicas utilizadas: redes neuronales, sistemas de clasificación, modelos cualitativos, y sistemas expertos, ilustradas con algunos ejemplos de aplicación.Con respecto a los sistemas basados en el conocimiento se analizan en primer lugar las condiciones para su aplicabilidad, y las formas de representación del conocimiento. A continuación se describen las distintas formas de razonamiento: redes neuronales, sistemas expertos y lógica difusa, y se realiza una comparación entre ellas. Se presenta una aplicación de las redes neuronales al análisis de series temporales de temperatura.Se trata también la problemática del análisis de los datos de operación mediante técnicas estadísticas y el empleo de técnicas de clasificación. Otro apartado está dedicado a los distintos tipos de modelos, incluyendo una discusión de los modelos cualitativos.Se describe el sistema de diseño asistido por ordenador para el diseño de sistemas de supervisión CASSD que se utiliza en esta tesis, y las herramientas de análisis para obtener información cualitativa del comportamiento del proceso: Abstractores y ALCMEN. Se incluye un ejemplo de aplicación de estas técnicas para hallar las relaciones entre la temperatura y las acciones del operador. Finalmente se analizan las principales características de los sistemas expertos en general, y del sistema experto CEES 2.0 que también forma parte del sistema CASSD que se ha utilizado.El capítulo 6, Resultados, muestra los resultados obtenidos mediante la aplicación de las diferentes técnicas, redes neuronales, clasificación, el desarrollo de la modelización del proceso de combustión, y la generación de reglas. Dentro del apartado de análisis de datos se emplea una red neuronal para la clasificación de una señal de temperatura. También se describe la utilización del método LINNEO+ para la clasificación de los estados de operación de la planta.En el apartado dedicado a la modelización se desarrolla un modelo de combustión que sirve de base para analizar el comportamiento del horno en régimen estacionario y dinámico. Se define un parámetro, la superficie de llama, relacionado con la extensión del fuego en la parrilla. Mediante un modelo linealizado se analiza la respuesta dinámica del proceso de incineración. Luego se pasa a la definición de relaciones cualitativas entre las variables que se utilizan en la elaboración de un modelo cualitativo. A continuación se desarrolla un nuevo modelo cualitativo, tomando como base el modelo dinámico analítico.Finalmente se aborda el desarrollo de la base de conocimiento del sistema experto, mediante la generación de reglas En el capítulo 7, Sistema de control de una planta incineradora, se analizan los objetivos de un sistema de control de una planta incineradora, su diseño e implementación. Se describen los objetivos básicos del sistema de control de la combustión, su configuración y la implementación en Matlab/Simulink utilizando las distintas herramientas que se han desarrollado en el capítulo anterior.Por último para mostrar como pueden aplicarse los distintos métodos desarrollados en esta tesis se construye un sistema experto para mantener constante la temperatura del horno actuando sobre la alimentación de residuos.Finalmente en el capítulo Conclusiones, se presentan las conclusiones y resultados de esta tesis.

Design and management of sustainable built environments

The United Nation Intergovernmental Panel on Climate Change (IPCC) makes it clear that climate change is due to human activities and it recognises buildings as a distinct sector among the seven analysed in its 2007 Fourth Assessment Report. Global concerns have escalated regarding carbon emissions and sustainability in the built environment. The built environment is a human-made setting to accommodate human activities, including building and transport, which covers an interdisciplinary field addressing design, construction, operation and management. Specifically, Sustainable Buildings are expected to achieve high performance throughout the life-cycle of siting, design, construction, operation, maintenance and demolition, in the following areas: • energy and resource efficiency; • cost effectiveness; • minimisation of emissions that negatively impact global warming, indoor air quality and acid rain; • minimisation of waste discharges; and • maximisation of fulfilling the requirements of occupants’ health and wellbeing. Professionals in the built environment sector, for example, urban planners, architects, building scientists, engineers, facilities managers, performance assessors and policy makers, will play a significant role in delivering a sustainable built environment. Delivering a sustainable built environment needs an integrated approach and so it is essential for built environment professionals to have interdisciplinary knowledge in building design and management . Building and urban designers need to have a good understanding of the planning, design and management of the buildings in terms of low carbon and energy efficiency. There are a limited number of traditional engineers who know how to design environmental systems (services engineer) in great detail. Yet there is a very large market for technologists with multi-disciplinary skills who are able to identify the need for, envision and manage the deployment of a wide range of sustainable technologies, both passive (architectural) and active (engineering system),, and select the appropriate approach. Employers seek applicants with skills in analysis, decision-making/assessment, computer simulation and project implementation. An integrated approach is expected in practice, which encourages built environment professionals to think ‘out of the box’ and learn to analyse real problems using the most relevant approach, irrespective of discipline. The Design and Management of Sustainable Built Environment book aims to produce readers able to apply fundamental scientific research to solve real-world problems in the general area of sustainability in the built environment. The book contains twenty chapters covering climate change and sustainability, urban design and assessment (planning, travel systems, urban environment), urban management (drainage and waste), buildings (indoor environment, architectural design and renewable energy), simulation techniques (energy and airflow), management (end-user behaviour, facilities and information), assessment (materials and tools), procurement, and cases studies ( BRE Science Park). Chapters one and two present general global issues of climate change and sustainability in the built environment. Chapter one illustrates that applying the concepts of sustainability to the urban environment (buildings, infrastructure, transport) raises some key issues for tackling climate change, resource depletion and energy supply. Buildings, and the way we operate them, play a vital role in tackling global greenhouse gas emissions. Holistic thinking and an integrated approach in delivering a sustainable built environment is highlighted. Chapter two demonstrates the important role that buildings (their services and appliances) and building energy policies play in this area. Substantial investment is required to implement such policies, much of which will earn a good return. Chapters three and four discuss urban planning and transport. Chapter three stresses the importance of using modelling techniques at the early stage for strategic master-planning of a new development and a retrofit programme. A general framework for sustainable urban-scale master planning is introduced. This chapter also addressed the needs for the development of a more holistic and pragmatic view of how the built environment performs, , in order to produce tools to help design for a higher level of sustainability and, in particular, how people plan, design and use it. Chapter four discusses microcirculation, which is an emerging and challenging area which relates to changing travel behaviour in the quest for urban sustainability. The chapter outlines the main drivers for travel behaviour and choices, the workings of the transport system and its interaction with urban land use. It also covers the new approach to managing urban traffic to maximise economic, social and environmental benefits. Chapters five and six present topics related to urban microclimates including thermal and acoustic issues. Chapter five discusses urban microclimates and urban heat island, as well as the interrelationship of urban design (urban forms and textures) with energy consumption and urban thermal comfort. It introduces models that can be used to analyse microclimates for a careful and considered approach for planning sustainable cities. Chapter six discusses urban acoustics, focusing on urban noise evaluation and mitigation. Various prediction and simulation methods for sound propagation in micro-scale urban areas, as well as techniques for large scale urban noise-mapping, are presented. Chapters seven and eight discuss urban drainage and waste management. The growing demand for housing and commercial developments in the 21st century, as well as the environmental pressure caused by climate change, has increased the focus on sustainable urban drainage systems (SUDS). Chapter seven discusses the SUDS concept which is an integrated approach to surface water management. It takes into consideration quality, quantity and amenity aspects to provide a more pleasant habitat for people as well as increasing the biodiversity value of the local environment. Chapter eight discusses the main issues in urban waste management. It points out that population increases, land use pressures, technical and socio-economic influences have become inextricably interwoven and how ensuring a safe means of dealing with humanity’s waste becomes more challenging. Sustainable building design needs to consider healthy indoor environments, minimising energy for heating, cooling and lighting, and maximising the utilisation of renewable energy. Chapter nine considers how people respond to the physical environment and how that is used in the design of indoor environments. It considers environmental components such as thermal, acoustic, visual, air quality and vibration and their interaction and integration. Chapter ten introduces the concept of passive building design and its relevant strategies, including passive solar heating, shading, natural ventilation, daylighting and thermal mass, in order to minimise heating and cooling load as well as energy consumption for artificial lighting. Chapter eleven discusses the growing importance of integrating Renewable Energy Technologies (RETs) into buildings, the range of technologies currently available and what to consider during technology selection processes in order to minimise carbon emissions from burning fossil fuels. The chapter draws to a close by highlighting the issues concerning system design and the need for careful integration and management of RETs once installed; and for home owners and operators to understand the characteristics of the technology in their building. Computer simulation tools play a significant role in sustainable building design because, as the modern built environment design (building and systems) becomes more complex, it requires tools to assist in the design process. Chapter twelve gives an overview of the primary benefits and users of simulation programs, the role of simulation in the construction process and examines the validity and interpretation of simulation results. Chapter thirteen particularly focuses on the Computational Fluid Dynamics (CFD) simulation method used for optimisation and performance assessment of technologies and solutions for sustainable building design and its application through a series of cases studies. People and building performance are intimately linked. A better understanding of occupants’ interaction with the indoor environment is essential to building energy and facilities management. Chapter fourteen focuses on the issue of occupant behaviour; principally, its impact, and the influence of building performance on them. Chapter fifteen explores the discipline of facilities management and the contribution that this emerging profession makes to securing sustainable building performance. The chapter highlights a much greater diversity of opportunities in sustainable building design that extends well into the operational life. Chapter sixteen reviews the concepts of modelling information flows and the use of Building Information Modelling (BIM), describing these techniques and how these aspects of information management can help drive sustainability. An explanation is offered concerning why information management is the key to ‘life-cycle’ thinking in sustainable building and construction. Measurement of building performance and sustainability is a key issue in delivering a sustainable built environment. Chapter seventeen identifies the means by which construction materials can be evaluated with respect to their sustainability. It identifies the key issues that impact the sustainability of construction materials and the methodologies commonly used to assess them. Chapter eighteen focuses on the topics of green building assessment, green building materials, sustainable construction and operation. Commonly-used assessment tools such as BRE Environmental Assessment Method (BREEAM), Leadership in Energy and Environmental Design ( LEED) and others are introduced. Chapter nineteen discusses sustainable procurement which is one of the areas to have naturally emerged from the overall sustainable development agenda. It aims to ensure that current use of resources does not compromise the ability of future generations to meet their own needs. Chapter twenty is a best-practice exemplar - the BRE Innovation Park which features a number of demonstration buildings that have been built to the UK Government’s Code for Sustainable Homes. It showcases the very latest innovative methods of construction, and cutting edge technology for sustainable buildings. In summary, Design and Management of Sustainable Built Environment book is the result of co-operation and dedication of individual chapter authors. We hope readers benefit from gaining a broad interdisciplinary knowledge of design and management in the built environment in the context of sustainability. We believe that the knowledge and insights of our academics and professional colleagues from different institutions and disciplines illuminate a way of delivering sustainable built environment through holistic integrated design and management approaches. Last, but not least, I would like to take this opportunity to thank all the chapter authors for their contribution. I would like to thank David Lim for his assistance in the editorial work and proofreading.