Degradação de corantes têxteis e remediação de resíduos de tingimento por processos Fenton, foto-Fenton e eletro-Fenton

In this work the degradation of textile dyes were evaluated, using Fenton, photo-Fenton and electro-Fenton processes. Under optimized conditions Fenton and photo-Fenton processes showed high decolorization capacity of the model dyes. The electro-Fenton process was carried out in an undivided electrochemical reactor (1000 mL) equipped with a carbon-felt cathode (253 cm²) and a platinum gauze anode (6 cm²). Under optimal conditions (J: 1.6 mA cm-2, Na2SO4: 0.075 mol L-1, pH: 3) H2O2 concentration of about 60 mg L-1 was observed. The addition of Fe2+ (15 mg L-1) induces Fenton reactions that permit almost total decolorization of textile dyes.

Degradação de poluentes emergentes por processos Fenton e foto-Fenton

A continuous photochemical treatment system was developed for aiming the treatment of aqueous solutions containing relevant micro-pollutants (microcystin-LR, sulfamethoxazole and 17-b estradiol). The continuous photo-Fenton process provided high degradation efficiency. However, contact time between samples and the irradiated region is short relative to total treatment time, indicating that observed changes are predominantly due to the Fenton process. Higher degradation efficiency was observed in systems operated using two treatment cycles, the first involving a batch Fenton process and the second a continuous photo-Fenton treatment.

Fotodegradação de fenol e clorofenóis por processo foto-Fenton mediado por ferrioxalato

A influência de parâmetros operacionais como a agitação da solução durante irradiação solar e a vazão de alimentação de um fotorreator com irradiação artificial foi avaliada na fotodegradação de 2-clorofenol (2CF) e 2,4-diclorofenol (DCF) por processo foto-Fenton mediado por ferrioxalato. Após avaliação destes parâmetros, os sistemas foram aplicados na fotodegradação de fenol e de mono, (2-clorofenol e 4-clorofenol), di (2,4-diclorofenol) e tri (2,4,6-triclorofenol) clorofenóis a fim de avaliar a eficiência de fotodegradação destes compostos sob irradiação solar e artificial. Foi observada pequena diferença nas porcentagens de remoção de carbono orgânico total (COT) e de geração de íons cloreto nos experimentos de fotodegradação de 2CF sem agitação e com agitação sob irradiação solar. Sob irradiação artificial, um aumento da vazão de alimentação do sistema resultou em menor porcentagem de remoção de COT, ao passo que uma maior velocidade de remoção foi obtida devido a um menor tempo de irradiação. Foi então utilizada uma vazão intermediária de 33,4 mL min-1. Sob irradiação solar, foram necessários 15 minutos de irradiação para a completa remoção de todos os clorofenóis, entretanto para fenol, a completa remoção foi atingida em 20 minutos. Sob irradiação artificial, os clorofenóis foram removidos entre 4,5 e 6,5 minutos de irradiação. A velocidade de degradação aumenta ligeiramente com o aumento do número de cloros ligados ao anel aromático tanto sob irradiação artificial como solar.

Estudo da aplicação do processo foto-Fenton solar na degradação de efluentes de indústria de tintas

Neste trabalho estudou-se a aplicabilidade do processo foto-Fenton utilizando irradiação solar no tratamento de dois efluentes (A e B) de uma indústria de tintas. Foi avaliada a influência da concentração inicial de peróxido de hidrogênio e ferro na remoção de carbono orgânico dissolvido (COD). Nos primeiros minutos de irradiação foi observada a descoloração e a remoção de odores. Para o efluente A, atingiu-se 75 % de remoção de COD durante 60 minutos de irradiação. Para o efluente B, adições múltiplas de peróxido de hidrogênio foram necessárias para aumentar a remoção de COD, 43 % em 60 minutos de irradiação. Os resultados obtidos mostram que o processo foto-Fenton solar pode ser aplicado ao tratamento dos efluentes gerados na indústria de tintas.

Uso de reações de fenton na remediação de solo contaminado com p,p´ DDT

Neste trabalho foram estudados dois sistemas utilizando reações de Fenton para a remediação de um solo contaminado com p,p´ DDT. O primeiro envolveu a formação de uma lama com o solo contaminado, na qual foram adicionados os reagentes de Fenton. No segundo, não houve a formação de lama e os reagentes foram adicionados diretamente ao solo por meio de um "tubo injetor". Foram avaliados alguns parâmetros que podem influenciar a reação de Fenton, tais como minerais de ferro naturalmente presentes no solo e a irradiação solar. A principal espécie mineral de ferro encontrada no solo é a hematita (Fe2O3), que teve pouca influência na degradação do contaminante. Nos experimentos com lama sem adição de ferro solúvel a porcentagem de degradação do p,p´ DDT foi inferior a 25% após 24 horas de reação. Nos ensaios com lama na presença de ferro solúvel, a degradação do p,p´ DDT atingiu 70% em 32 horas, enquanto que nos experimentos sem lama, a porcentagem de degradação foi de 32% no mesmo intervalo de tempo. Em ambos os sistemas, a irradiação solar teve pouca influência na degradação do contaminante. Os resultados indicam que para um processo de remediação deste solo, há necessidade de adição de ferro solúvel e que o sistema em lama resulta em maior eficiência de degradação de p,p´ DDT.

Customer Driven Order-to-Delivery Process

This thesis was made for a large forest industry company’s business segment. The purpose of the study was to improve the performance of the order-to-delivery process of the business segment. The study proceeded in three phases. The first phase was to define customer expectations in the market. The second phase was to analyse the performance and the operations of the order-to-delivery process, and to define any challenges or problems in serving the customers. The third and final phase was improving the performance of the order-to-delivery process, within the scope defined by the first two phases. The analysis showed that the delivery reliability is an essential but a challenging issue in the case company’s markets. On delivery reliability standpoint, the most challenging factors were the detected information flow distortions within the company as well as in the whole supply chain, and the lack of horizontal control over the multi-stage process.

Photo-Fenton process for treating biological laboratory wastewater containing formaldehyde

Laboratories consume great amounts of hazardous chemicals substances and consequently generate wastewater containing them, for example formaldehyde. This substance is widely utilized to preserve biological samples generating many liters of this residue every year. The present work proposes the use of the photo-Fenton process to treat formaldehyde wastewater using sunlight irradiation. Some aspects were investigated such as the iron source, sample and hydrogen peroxide concentration and also the use of stirred systems. The use of ferrioxalate (0.5 mmol L-1) improved the efficiency of the process in relation to the use of iron nitrate, while at least 1.0 mol L-1 H2O2 is necessary to treat the sample of the 500 mg C L-1. Under these conditions, every formaldehyde detectable was degradeted and 89% of the dissolved organic carbon was removed in two hours of exposure to sunlight. These results are satisfaction considerate for São Paulo State Environmental Agency.

Customer Driven Service Development – Technology-based Care and Services for the Elderly

The objective of this master’s thesis was to examine technology-based smart home devices and services. Topic was approached through basic theories, transaction cost theory and resource-based view in order to build basis for this thesis. Conceptual framework was discussed by means of networks, value networks and service systems which provide a useful framework for service development. The needs of the elderly living at home were discussed in order to find out which technology-based services could be used to satisfy the needs. Segmentation and need data collected previously during proactive home visits was exploited and additionally a survey targeted to experts and professionals of social and health care sector was done to verify the needs. Finally, the results of the survey were analyzed using quality function deployment method to figure out the most important and suitable service offerings for the elderly. As a conclusion of analysis, social media and monitoring services are the most useful technology-based services. However, traditional home services will still maintain their necessity too.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.

Electrically driven fertilizer applicator controlled by fuzzy logic

The present study shows the development, simulation and actual implementation of a closed-loop controller based on fuzzy logic that is able to regulate and standardize the mass flow of a helical fertilizer applicator. The control algorithm was developed using MATLAB's Fuzzy Logic Toolbox. Both open and closed-loop simulations of the controller were performed in MATLAB's Simulink environment. The instantaneous deviation of the mass flow from the set point (SP), its derivative, the equipment´s translation velocity and acceleration were all used as input signals for the controller, whereas the voltage of the applicator's DC electric motor (DCEM) was driven by the controller as output signal. Calibration and validation of the rules and membership functions of the fuzzy logic were accomplished in the computer simulation phase, taking into account the system's response to SP changes. The mass flow variation coefficient, measured in experimental tests, ranged from 6.32 to 13.18%. The steady state error fell between -0.72 and 0.13g s-1 and the recorded average rise time of the system was 0.38 s. The implemented controller was able to both damp the oscillations in mass flow that are characteristic of helical fertilizer applicators, and to effectively respond to SP variations.

Application of electrokinetic Fenton process for the remediation of soil contaminated with HCB

Electrokinetic remediation coupled with Fenton oxidation, widely called as Electrokinetic Fenton process is a potential soil remediation technique used for low permeable soil. The applicability of the process has been proved with soil contaminated with a wide range of organic compounds from phenol to the most recalcitrant ones such as PAHs and POPs. This thesis summarizes the major findings observed during an Electrokinetic Fenton Process study conducted for the remediation of low permeable soil contaminated with HCB, a typical hydrophobic organic contaminant. Model low permeable soil, kaolin, was artificially contaminated with HCB and subjected to Electrokinetic Fenton treatments in a series of laboratory scale batch experiments. The use of cyclodextrins as an enhancement agent to mobilize the sorbed contaminant through the system was investigated. Major process hindrances such as the oxidant availability and treatment duration were also addressed. The HCB degradation along with other parameters like soil pH, redox and cumulative catholyte flow were analyzed and monitored. The results of the experiments strengthen the existing knowledge on electrokinetic Fenton process as a promising technology for the treatment of soil contaminated with hydrophobic organic compounds. It has been demonstrated that HCB sorbed to kaolin can be degraded by the use of high concentrations of hydrogen peroxide during such processes. The overall system performances were observed to be influenced by the point and mode of oxidant delivery. Furthermore, the study contributes to new knowledge in shortening the treatment duration by adopting an electrode polarity reversal during the process.

Climate driven changes in temperature, pH and food quality : effects on copepod reproduction

Increased emissions of greenhouse gases into the atmosphere are causing an anthropogenic climate change. The resulting global warming challenges the ability of organisms to adapt to the new temperature conditions. However, warming is not the only major threat. In marine environments, dissolution of carbon dioxide from the atmosphere causes a decrease in surface water pH, the so called ocean acidification. The temperature and acidification effects can interact, and create even larger problems for the marine flora and fauna than either of the effects would cause alone. I have used Baltic calanoid copepods (crustacean zooplankton) as my research object and studied their growth and stress responses using climate predictions projected for the next century. I have studied both direct temperature and pH effects on copepods, and indirect effects via their food: the changing phytoplankton spring bloom composition and toxic cyanobacterium. The main aims of my thesis were: 1) to find out how warming and acidification combined with a toxic cyanobacterium affect copepod reproductive success (egg production, egg viability, egg hatching success, offspring development) and oxidative balance (antioxidant capacity, oxidative damage), and 2) to reveal the possible food quality effects of spring phytoplankton bloom composition dominated by diatoms or dinoflagellates on reproducing copepods (egg production, egg hatching, RNA:DNA ratio). The two copepod genera used, Acartia sp. and Eurytemora affinis are the dominating mesozooplankton taxa (0.2 – 2 mm) in my study area the Gulf of Finland. The 20°C temperature seems to be within the tolerance limits of Acartia spp., because copepods can adapt to the temperature phenotypically by adjusting their body size. Copepods are also able to tolerate a pH decrease of 0.4 from present values, but the combination of warm water and decreased pH causes problems for them. In my studies, the copepod oxidative balance was negatively influenced by the interaction of these two environmental factors, and egg and nauplii production were lower at 20°C and lower pH, than at 20°C and ambient pH. However, presence of toxic cyanobacterium Nodularia spumigena improved the copepod oxidative balance and helped to resist the environmental stress, in question. In addition, adaptive maternal effects seem to be an important adaptation mechanism in a changing environment, but it depends on the condition of the female copepod and her diet how much she can invest in her offspring. I did not find systematic food quality difference between diatoms and dinoflagellates. There are both good and bad diatom and dinoflagellate species. Instead, the dominating species in the phytoplankton bloom composition has a central role in determining the food quality, although copepods aim at obtaining as a balanced diet as possible by foraging on several species. If the dominating species is of poor quality it can cause stress when ingested, or lead to non-optimal foraging if rejected. My thesis demonstrates that climate change induced water temperature and pH changes can cause problems to Baltic Sea copepod communities. However, their resilience depends substantially on their diet, and therefore the response of phytoplankton to the environmental changes. As copepods are an important link in pelagic food webs, their future success can have far reaching consequences, for example on fish stocks.

Patron Driven Acquisition (PDA) e-kirjojen hankintamenetelmänä

Esitys Kirjastoverkkopäivillä 23.10.2012 Helsingissä

“Valley co-creation” – exploring the emergence of a cultural product in an entrepreneur-driven value network: Case study: Black Weekend festival

The interconnected domains are attracting interest from industries and academia, although this phenomenon, called ‘convergence’ is not new. Organizational research has indeed focused on uncovering co-creation for manufacturing and the industrial organization, with limited implications to entrepreneurship. Although convergence has been characterized as a process connecting seemingly disparate disciplines, it is argued that these studies tend to leave the creative industries unnoticed. With the art market boom and new forms of collaboration riding past the institution-focused arts marketing literature, this thesis takes a leap to uncover the processes of entrepreneurship in the emergence of a cultural product. As a symbolic work of synergism itself, the thesis combines organizational theory with literature in natural sciences and arts. Assuming nonlinearity, a framework is created for analysing aesthetic experience in an empirical event where network actors are connected to multiple contexts. As the focal case in study, the empirical analysis performed for a music festival organized in a skiing resort in the French Alps in March. The researcher attends the festival and models its cocreation process by enquiring from an artist, festival organisers, and a festival visitor. The findings contribute to fields of entrepreneurship, aesthetics and marketing mainly. It is found that the network actors engage in intimate and creative interaction where activity patterns are interrupted and cultural elements combined. This process is considered to both create and destruct value, through identity building, legitimisation, learning, and access to larger audiences, and it is considered particularly useful for domains where resources are too restrained for conventional marketing practices. This thesis uncovered the role of artists and informants and posits that particularly through experience design, this type of skilled individual be regarded more often as a research informant. Future research is encouraged to engage in convergence by experimenting with different fields and research designs, and it is suggested that future studies could arrive at different descriptive results.

Energy-efficient control strategies for variable speed driven parallel pumping systems based on pump operation point monitoring with frequency converters

The pumping processes requiring wide range of flow are often equipped with parallelconnected centrifugal pumps. In parallel pumping systems, the use of variable speed control allows that the required output for the process can be delivered with a varying number of operated pump units and selected rotational speed references. However, the optimization of the parallel-connected rotational speed controlled pump units often requires adaptive modelling of both parallel pump characteristics and the surrounding system in varying operation conditions. The available information required for the system modelling in typical parallel pumping applications such as waste water treatment and various cooling and water delivery pumping tasks can be limited, and the lack of real-time operation point monitoring often sets limits for accurate energy efficiency optimization. Hence, alternatives for easily implementable control strategies which can be adopted with minimum system data are necessary. This doctoral thesis concentrates on the methods that allow the energy efficient use of variable speed controlled parallel pumps in system scenarios in which the parallel pump units consist of a centrifugal pump, an electric motor, and a frequency converter. Firstly, the suitable operation conditions for variable speed controlled parallel pumps are studied. Secondly, methods for determining the output of each parallel pump unit using characteristic curve-based operation point estimation with frequency converter are discussed. Thirdly, the implementation of the control strategy based on real-time pump operation point estimation and sub-optimization of each parallel pump unit is studied. The findings of the thesis support the idea that the energy efficiency of the pumping can be increased without the installation of new, more efficient components in the systems by simply adopting suitable control strategies. An easily implementable and adaptive control strategy for variable speed controlled parallel pumping systems can be created by utilizing the pump operation point estimation available in modern frequency converters. Hence, additional real-time flow metering, start-up measurements, and detailed system model are unnecessary, and the pumping task can be fulfilled by determining a speed reference for each parallel-pump unit which suggests the energy efficient operation of the pumping system.