Regenerative amplifier with continuously variable pulse duration used in an optical parametric chirped-pulse amplification laser system for synchronous pumping

A Nd:glass regenerative amplifier has been set up to generate the pumping pulse with variable pulse width for an optical parametric chirped-pulse amplification (OPCPA) laser system. Each pulse of the pulse train from a cw self-mode-locking femtosecond Ti:sapphire oscillator is stretched to approximate to300 ps at 1062 nm to be split equally and injected into a nonlinear crystal and the Nd:glass regenerative amplifier, as the chirped signal pulse train and the seed pulse train of the pumping laser system, respectively. By adjusting the cavity length of the regenerative amplifier directly, the width of amplified pulse could be varied continuously from approximate to300 ps to approximate to3 ns. The chirped signal pulse for the OPCPA laser system and the seed pulse for the pumping laser system come from the same oscillator, so that the time jitter between the signal pulse and the pumping pulse in optical parametric amplification stages could be <10 ps. (C) 2003 Society of Photo-Optical Instrumentation Engineers.

基于强激光辐照固体锡靶产生极紫外光源的实验研究

建立了一套利用高功率YAG激光器辐照固体锡靶产生高转换效率极紫外光(extreme ultraviolet)源的实验装置.利用建立的实验装置开展了极紫外光源的强度和转换效率与抽运激光强度关系的实验研究,发现极紫外光源的转换效率随抽运激光强度的变化具有饱和效应.实验发现:当抽运激光能量达到250mJ时,极紫外光源的转换效率最高,波长为13.5nm处0.27nm带宽范围内的极紫外光源的能量转换效率为1.6%,此时对应的激光强度为1.8×1011W/cm2.

图像处理在光路自动准直系统中的应用

光路自动准直系统应用于惯性约束聚变的高功率激光装置中的光束自动调整。图像处理是光路自动准直的关键技术之一。针对神光Ⅲ原型装置，结合阈值化、重心法、中值滤波和圆拟合等多种不同的图像处理方法设计了一套合理的准直方案，并且在模拟实验平台上进行了实验验证。实验结果表明，光路自动准直系统能够在15min之内顺利完成光路的自动调整，光束近场调整精度优于近场光斑的±0．5％，光束远场调整精度≤±0．3″，满足了原型装置的总体要求。

基于孔径耦合带状线的激光脉冲整形系统

实现了一种新型的激光脉冲整形系统，该系统使用了一个由孔径耦合带状线（ACSL）电脉冲整形器驱动的电光调制器。一个电脉冲整形器由两条通过其公共接地板上的耦合孔径发生耦合作用的带状传输线所组成的四端口装置。更换具有不同耦合孔径的公共接地板，该电脉冲整形发生器可以具有150ps时间结构的任意整形电脉冲。将任意整形的电脉冲输入到电光调制器上，就可以得到任意整形的激光脉冲。利用该系统，激光脉冲整形系统能够产生具有150ps前后沿，1～3ns脉冲宽度可调、高对比度、光滑过渡以及任意整形的激光脉冲。

高功率激光装置前端系统激光脉冲的时间整形及修正技术

针对激光惯性约束聚变实验研究对高功率激光驱动器前端系统复杂时间形状种子激光脉冲的需求, 应用孔径耦合带状线集成波导整形系统设计了满足需要的前端整形激光脉冲。用一种新方法精确计算了孔径耦合带状线电脉冲整形器的耦合系数和孔径宽度的数值关系, 并针对高衬比度整形激光脉冲的需求, 提出了高衬比度双极型集成波导整形系统方案。由该系统可以得到100 ps脉冲前沿、1～3 ns脉冲宽度可调、高衬比度(大于100∶1)、光滑无纹波调制、可精确满足神光II八路及第九路装置需求的前端整形激光脉冲。

神光Ⅱ升级装置终端光学组件的排布设计

设计高功率激光装置靶场终端光学组件(FOA)时考虑的重要因素是鬼像对光学元件的破坏。由于神光Ⅱ升级装置(SG-Ⅱ-U)的输出能量高、靶场空间小、鬼像分布情况复杂,导致了终端光学组件的设计难度很高。用自主研发的鬼像控制设计软件对神光Ⅱ升级装置靶场终端光学组件排布进行设计,给出了进行鬼像控制设计时需考虑的设计因素,并对比研究了两种靶场终端光学组件设计方案的优缺点,最后结合神光Ⅱ升级装置的特点,优化设计出神光Ⅱ升级装置靶场终端光学组件的最终排布方案。

Thermal and thermal-optical effects in high-power photonic crystal fiber lasers

A series-parallel model is introduced to calculate the effective thermal conductivities of hollow claddings of photonic crystal fibers ( PCFs ). The temperature distribution and thermal-optical properties of PCF lasers are studied by solving the heat transfer equations. The average power scaling of the PCF lasers in respect of the thermal effects is also discussed. (c) 2006 Society of Photo-Optical Instrumentation Engineers.

Thermal and thermal-optical effects in high-power photonic crystal fiber lasers

A series-parallel model is introduced to calculate the effective thermal conductivities of hollow claddings of photonic crystal fibers ( PCFs ). The temperature distribution and thermal-optical properties of PCF lasers are studied by solving the heat transfer equations. The average power scaling of the PCF lasers in respect of the thermal effects is also discussed. (c) 2006 Society of Photo-Optical Instrumentation Engineers.

110-W fiber laser with homemade double-clad fiber

A high-power ytterbium-doped fiber laser (YDFL) with homemade double-clad fiber (DCF) is introduced in this letter. The geometric parameter and laser characteristics of the fiber have been studied. With one-end-pumping scheme, pumped by a high-power laser diode with launching power of 280 W, a maximum continuous wave (CW) output of 110 W is obtained with an optical-to-optical efficiency of 40%.