Reguladores vegetais e nutrientes minerais no metabolismo de plantas de tomateiro

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Ethanol steam reforming over rhodium and cobalt-based catalysts: Effect of the support

The effect of support on the properties of rhodium and cobalt-based catalysts for ethanol steam reforming was studied in this work, by comparing the use of magnesia, alumina and Mg-Al oxide (obtained from hydrotalcite) as supports. It was found that metallic rhodium particles with around 2.4-2.6 nm were formed on all supports, but Mg-Al oxide led to the narrowest particles size distribution; cobalt was supposed to be located on the support, affecting its acidity. Rhodium interacts strongly with the support in the order: alumina> Mg-Al oxide > magnesia. The magnesium-containing catalysts showed low ethene selectivity and high hydrogen selectivity while the alumina-based ones showed high ethene selectivity, assigned to the Lewis sites of alumina. The Mg-Al oxide-supported rhodium and cobalt catalyst was the most promising sample to produce hydrogen by ethanol reforming, showing the highest hydrogen yield, low ethene selectivity and high specific surface area during reaction. Copyright (C) 2011, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

Field dependent transition to the non-linear regime in magnetic hyperthermia experiments: Comparison between maghemite, copper, zinc, nickel and cobalt ferrite nanoparticles of similar sizes

Further advances in magnetic hyperthermia might be limited by biological constraints, such as using sufficiently low frequencies and low field amplitudes to inhibit harmful eddy currents inside the patient's body. These incite the need to optimize the heating efficiency of the nanoparticles, referred to as the specific absorption rate (SAR). Among the several properties currently under research, one of particular importance is the transition from the linear to the non-linear regime that takes place as the field amplitude is increased, an aspect where the magnetic anisotropy is expected to play a fundamental role. In this paper we investigate the heating properties of cobalt ferrite and maghemite nanoparticles under the influence of a 500 kHz sinusoidal magnetic field with varying amplitude, up to 134 Oe. The particles were characterized by TEM, XRD, FMR and VSM, from which most relevant morphological, structural and magnetic properties were inferred. Both materials have similar size distributions and saturation magnetization, but strikingly different magnetic anisotropies. From magnetic hyperthermia experiments we found that, while at low fields maghemite is the best nanomaterial for hyperthermia applications, above a critical field, close to the transition from the linear to the non-linear regime, cobalt ferrite becomes more efficient. The results were also analyzed with respect to the energy conversion efficiency and compared with dynamic hysteresis simulations. Additional analysis with nickel, zinc and copper-ferrite nanoparticles of similar sizes confirmed the importance of the magnetic anisotropy and the damping factor. Further, the analysis of the characterization parameters suggested core-shell nanostructures, probably due to a surface passivation process during the nanoparticle synthesis. Finally, we discussed the effect of particle-particle interactions and its consequences, in particular regarding discrepancies between estimated parameters and expected theoretical predictions. Copyright 2012 Author(s). This article is distributed under a Creative Commons Attribution 3.0 Unported License. [http://dx.doi. org/10.1063/1.4739533]

Tailoring Molecular Architectures with Cobalt Tetrasulfonated Phthalocyanine: Immobilization in Layer-by-Layer Films and Sensing Applications

In the field of organic thin films, manipulation at the nanoscale can be obtained by immobilization of different materials on platforms designed to enhance a specific property via the layer-by-layer technique. In this paper we describe the fabrication of nanostructured films containing cobalt tetrasulfonated phthalocyanine (CoTsPc) obtained through the layer-by-layer architecture and assembled with linear poly(allylamine hydrochloride) (PAH) and poly(amidoamine) dendrimer (PAMAM) polyelectrolytes. Film growth was monitored by UV-vis spectroscopy following the Q band of CoTsPc and revealed a linear growth for both systems. Fourier transform infrared (FTIR) spectroscopy showed that the driving force keeping the structure of the films was achieved upon interactions of CoTsPc sulfonic groups with protonated amine groups present in the positive polyelectrolyte. A comprehensive SPR investigation on film growth reproduced the deposition process dynamically and provided an estimation of the thicknesses of the layers. Both FTIR and SPR techniques suggested a preferential orientation of the Pc ring parallel to the substrate. The electrical conductivity of the PAH films deposited on interdigitated electrodes was found to be very sensitive to water vapor. These results point to the development of a phthalocyanine-based humidity sensor obtained from a simple thin film deposition technique, whose ability to tailor molecular organization was crucial to achieve high sensitivity.

Magnetic hyperthermia investigation of cobalt ferrite nanoparticles: Comparison between experiment, linear response theory, and dynamic hysteresis simulations

Considerable effort has been made in recent years to optimize materials properties for magnetic hyperthermia applications. However, due to the complexity of the problem, several aspects pertaining to the combined influence of the different parameters involved still remain unclear. In this paper, we discuss in detail the role of the magnetic anisotropy on the specific absorption rate of cobalt-ferrite nanoparticles with diameters ranging from 3 to 14 nm. The structural characterization was carried out using x-ray diffraction and Rietveld analysis and all relevant magnetic parameters were extracted from vibrating sample magnetometry. Hyperthermia investigations were performed at 500 kHz with a sinusoidal magnetic field amplitude of up to 68 Oe. The specific absorption rate was investigated as a function of the coercive field, saturation magnetization, particle size, and magnetic anisotropy. The experimental results were also compared with theoretical predictions from the linear response theory and dynamic hysteresis simulations, where exceptional agreement was found in both cases. Our results show that the specific absorption rate has a narrow and pronounced maxima for intermediate anisotropy values. This not only highlights the importance of this parameter but also shows that in order to obtain optimum efficiency in hyperthermia applications, it is necessary to carefully tailor the materials properties during the synthesis process. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4729271]

Adubação mineral com cobalto e molibdênio na cultura da soja

Altas produtividades de soja requerem grandes quantidades de nitrogênio, que podem ser obtidas principalmente, a partir da fixação simbiótica. No entanto, há possibilidade da eficiência desse processo biológico ser prejudicada pela deficiência de micronutrientes, especialmente de cobalto e molibdênio. Nesse contexto, objetivou-se com o presente trabalho avaliar a eficiência agronômica e a forma de aplicação de adubação mineral com cobalto e molibdênio na cultura da soja. Para tanto, a cultivar CD-206 foi submetida a diferentes tratamentos que consistiram da combinação entre aplicação de Co e Mo via tratamento de sementes e adubação foliar. As características agronômicas avaliadas foram o número de nódulos, massa seca da parte aérea, massa seca de raiz, número de vagens, número de grãos, massa de mil grãos e produção de grãos. A aplicação de molibdênio e cobalto via sementes e/ ou adubação foliar no estádio V4 (terceira folha trifoliolada completamente desenvolvida, quarto nó) promoveram incrementos significativos no rendimento da cultura. Respostas positivas ao cobalto e molibdênio também foram observadas no número de nódulos, vagens e grãos, com aumentos de até 240 kg ha-1 no rendimento da cultura. Os parâmetros agronômicos avaliados foram afetados positivamente pela aplicação de Co e Mo, principalmente quanto aplicado tanto via semente como foliar (TS + V4), inclusive para a produtividade de grãos. A forma de aplicação não foi significativamente distinta, ou seja, tanto a aplicação via semente como via foliar foram eficientes no fornecimento destes nutrientes para a cultura da soja.

Layer-by-Layer assembled cobalt ferrite nanoparticles for chemical sensing

Ultra-thin (thicknesses of 50-90 nm) nanocomposite films of cobalt ferrite nanoparticles (np-CoFe2O4, 18 nm in diameter) and polyelectrolytes (doped polyaniline-PANI, poly-3,4-ethylenedioxy thiophene: polystyrene sulfonic acid-PEDOT:PSS, and sulfonated lignin-SL) are assembled layer-by-layer onto interdigitated microelectrodes aiming at to create novel nanostructured sensoactive materials for liquid media chemical sensors. The nanocomposites display a distinctive globular morphology with nanoparticles densely-packed while surrounded by polyelectrolytes. Due to the presence of np-CoFe2O4 the nanocomposites display low electrical conductivity according to impedance data. On the other hand, this apparent shortcoming turns such nanocomposites much more sensitive to the presence of ions in solution than films made exclusively of conducting polyelectrolytes. For example, the electrical resistance of np-CoFe2O4/PEDOT:PSS and PANI/SL/np-CoFe2O4/SL architectures has a 10-fold decrease when they are immersed in 20 mmol. L-1 NaCl solution. Impedance spectra fitted with the response of an equivalent circuit model suggest that the interface created between nanoparticles and polyelectrolytes plays a major role on the nanocomposites electrical/dielectrical behavior. Since charge transport is sensitive to nanoparticle-polyelectrolyte interfaces as well as to the physicochemical conditions of the environment, the np-CoFe2O4-based nanocomposites can be used as sensing elements in chemical sensors operated under ac regime and room temperature.

Dielectric properties of cobalt ferrite nanoparticles in ultrathin nanocomposite films

Multilayered nanocomposite films (thickness 50-90 nm) of cobalt ferrite nanoparticles (np-CoFe2O4, 18 nm) were deposited on top of interdigitated microelectrodes by the layer-by-layer technique in order to study their dielectric properties. For that purpose, two different types of nanocomposite films were prepared by assembling np-CoFe2O4 either with poly(3,4-ethylenedioxy thiophene):poly(styrene sulfonic acid) or with polyaniline and sulfonated lignin. Despite the different film architectures, the morphology of both was dominated by densely-packed layers of nanoparticles surrounded by polyelectrolytes. The dominant effect of np-CoFe2O4 was also observed after impedance spectroscopy measurements, which revealed that dielectric behavior of the nanocomposites was largely influenced by the charge transport across nanoparticle-polyelectrolyte interfaces. For example, nanocomposites containing np-CoFe2O4 exhibited a single low-frequency relaxation process, with time constants exceeding 15 ms. At 1 kHz, the dielectric constant and the dissipation factor (tan ᵟ) of these nanocomposites were 15 and 0.15, respectively. These values are substantially inferior to those reported for pressed pellets made exclusively of similar nanoparticles. Impedance data were further fitted with equivalent circuit models from which individual contributions of particle's bulk and interfaces to the charge transport within the nanocomposites could be evaluated. The present study evidences that such nanocomposites display a dielectric behavior dissimilar from that exhibited by their individual counterparts much likely due to enlarged nanoparticle- polyelectrolyte interfaces.

Structural investigation of Nb-based layer sulfides

In this work we have investigated the intercalation of electron-donors between NbS2 slabs in Nb-based layer sulfides. Two series of Sr substituted Nb-based misfit sulfides belonging to the 1.5Q/1H and 1Q/1H series of misfit layer compounds have been synthesised. For large lanthanides (Ln=La, Ce), only the 1Q/1H compounds formed whereas for smaller lanthanides and yttrium, both types of phases can be obtained. The crystal structure of misfit sulfide (Pr0.55Sr0.45S)1.15NbS2 has been refined using the composite approach. In the Q-slab, Pr-atoms are partly replaced by Sr with a random distribution over one cation position. The crystal structure of misfit sulfide [(Sm1/3Sr2/3S)1.5]1.15NbS2 belonging to the 1.5Q/1H series have also been determined. The obtained results suggest a preferred occupancy of the cation positions in the slab where Sr atoms mainly occupy positions on the exterior of the slab while Sm atoms are in the center of the slab. The (La1-xSrxS)1.15NbS2 solid solution (0.1<x<0.9) has also been studied. It was found that the maximum value of Sr substitution is 40-50% and therefore, the minimal value of charge transfer to stabilize this structure type is about 0.6ē per Nb atom. An attempt to synthesize SrxNbS2 (0.1≤x≤0.5) intercalates was made but single phases were not obtained and increasing the temperature from 1000оС to 1100оС leads to the decomposition of these intercalates. Single crystals of Sr0.22Nb1.05S2 and Sr0.23NbS2 were found and their structures were determined. The structures belong to two different types of packings with statistical distribution of Sr between layers. A new superconducting sulfide, "EuNb2S5", was investigated by ED and HREM and its structure model consisting of Nb7S14 and (Eu3S4)2 slabs alternating along the c-axis is suggested. An attempt to suggest a model for the structure of "SrNb2S5" by means of X-ray single crystal diffraction was made. The proposed structure consists of two types of slabs: a Nb7S14 and a [Sr6(NbS4)2S] slab with niobium in tetrahedral coordination. It is shown that "SrNb2S5" and "EuNb2S5" are have similar structures. For the first time, single crystals of the complex sulfide BaNb0.9S3 have also been studied by means of X-ray single crystal diffraction. The single crystal refinement and EDX analysis showed the existence of cation vacancies at the niobium position. BaNb0.9S3 has also been studied by ED and no superstructure was found which implies that and the vacancies are statistically distributed. No improvement of the magnetic properties of the studied compounds was observed in comparison to NbS2.

Approccio SEM-AVS (Simultaneously Extracted Metals-Acid Volatile Sulfides) per la valutazione del rischio ambientale dei metalli nei sedimenti della Pialassa Baiona

La Pialassa Baiona è una laguna sottoposta a diversi vincoli normativi, visto il suo inquadramento tra le aree SIC e ZPS, e soggetta a diverse sorgenti di disturbo antropico, più intense negli anni ‘50-‘70. Questa tesi si propone lo scopo di valutare il rischio associato ai metalli bivalenti presenti nei sedimenti della Pialassa Baiona attraverso tre approcci: il primo riguarda la determinazione della frazione biodisponibile dei metalli presenti nei sedimenti attraverso la determinazione dei solfuri acidi volatili (AVS) e dei metalli simultaneamente estraibili (SEM), nonché la valutazione della potenziale tossicità dei sedimenti attraverso la valutazione del rapporto molare SEM/AVS, il secondo approccio considera invece il contenuto pseudo totale dei metalli bivalenti (Cd, Cu, Ni, Pb e Zn) e il loro confronto sia con i valori tipici di fondo naturale del Mar Adriatico che con i valori guida di riferimento internazionale (Threshold Effect Level, TEL e Probable Effect Level, PEL) al fine di valutare lo stato di qualità dei sedimenti della zona d’indagine. Il terzo approccio considera l’influenza del gradiente naturale terra-mare tipico delle zone di transizione e del gradiente antropico legato alla vicinanza dell’area industriale alla Pialassa Baiona, sulla distribuzione spaziale dei metalli oggetto di questo studio. I risultati ottenuti evidenziano che l’area più prossima alla zona industriale e al contempo più lontana dall’effetto del ricambio delle acque e di dilavamento ad opera del mare, è risultata quella con livelli significativamente più elevati per la maggior parte dei metalli analizzati. Questo permette di ipotizzare un’influenza diretta delle sorgenti di inquinanti, ma anche un effetto dispersivo della circolazione. Gli AVS hanno invece evidenziato un gradiente terra-mare; ciò comporta che nelle zone più prossime all’influenza del mare si sono riscontrate concentrazioni minori di AVS. La valutazione della potenziale tossicità dei metalli in termini di rapporto SEM/AVS non ha evidenziato la presenza di siti a rischio per il biota acquatico, se non per un unico sito prossimo all’area industriale.

Cobalt dotiertes ZnO als verdünnter magnetischer Halbleiter

Verdünnte magnetische Halbleiter (DMS) sind technologisch vielversprechende Materialien mit sowohl ferromagnetischen als auch halbleitenden Eigenschaften. Sie gehören zu den entscheidenden Verbindungen bei der Entwicklung neuartiger Spintronikanwendungen. Bisher scheiterte der technologische Einsatz jedoch daran, dass die Curie Temperatur der meisten magnetischen Halbleiter viel zu niedrig ist. Neue Verbindungen auf Basis von ZnO wie Zn1-xCoxO sollen jedoch Ferromagnetismus oberhalb von Raumtemperatur zeigen. Die theoretischen Grundlagen der magnetischen Wechselwirkungen sind jedoch nicht verstanden und erfordern daher umfangreiche experimentelle Untersuchungen. Im Rahmen dieser Arbeit wurden dünne Filme aus Zn0.95Co0.05O mittels Laserablation hergestellt und bezüglich ihrer magnetischen, elektrischen und strukturellen Eigenschaften untersucht, mit dem Ziel den Ferromagnetismus in diesem Material besser zu verstehen. Dabei kamen verschiedene experimentelle Methoden zum Einsatz: wie Magnetometrie, Röntgendiffraktometrie, Magnetischer Röntgenzirkulardichroismus (XMCD), Elektronenspinresonanz sowie magnetoelektrische Transportmessungen. Bei entsprechend defektfördernden Herstellungsbedingungen zeigen die Proben klare ferromagnetische Eigenschaften oberhalb von Raumtemperatur mit einer Sättigungsmagnetisierung von ca. 2 Bohr Magneton / Co sowie einer Remanenz von bis zu 90%. Elektrische Transportmessungen zeigen zudem einen deutlichen Magnetowiderstand sowie einen anomalen Hall Effekt. Letzterer steigt mit der Probenmagnetisierung und spricht für intrinsischen Ferromagnetismus sowie eine geringe Spinpolarisation. Da der Ferromagnetismus mit höherer Ladungsträgerdichte jedoch verschwindet, ist eine ferromagnetische Wechselwirkung über die Leitungselektronen auszuschließen. Eine genauere Auswertung der magnetoelektrischen Messdaten deutet zudem auf ein leitendes Störstellenband hin, das unter Umständen selbst spinpolarisiert ist. Vieles spricht somit dafür, dass die ferromagnetische Ordnung über magnetische Polaronen zustande kommt. Einige strukturelle und magnetometrische Ergebnisse sowie Elektronenspinresonanzmessungen deuten zudem auf metallische Ausscheidungen in Form von Cobalt Clustern hin, die einen zusätzlichen extrinsischen ferromagnetischen Beitrag liefern, der deutlich größer sein könnte als der intrinsische. Überraschenderweise zeigen XMCD Messungen jedoch, dass Cobalt überhaupt nicht am Ferromagnetismus beteiligt ist. Insgesamt gibt es Anzeichen, dass magnetische Defekte eine entscheidende Rolle hinsichtlich des Magnetismus in Zn0.95Co0.05O spielen.

Valutazione del rilascio ionico in pazienti portatori di protesi di rivestimento d'anca BHR: confronto a lungo termine con artroplastica totale d'anca metallo-metallo

Lo scopo di questo studio è stato quello di determinare se a lungo termine le concentrazioni sieriche di ioni nei pazienti con protesi di rivestimento d’anca metallo-metallo (MOM-HR, metal-on-metal hip resurfacing) fossero differenti da quelle valutate nei pazienti con protesi totale d’anca metallo-metallo e testa del diametro di 28 mm (MOM-THA, metal-on-metal total hip arthroplasty); inoltre è stato valutato se le concentrazioni ioniche fossero al di sopra dei valori di riferimento e se fosse possibile stabilire l’esistenza di una relazione tra sesso e concentrazioni di ioni con riferimento al tipo di impianto. Il gruppo MOM-HR era costituito da 25 pazienti mentre il gruppo MOM-THA era di 16 pazienti. Per poter ricavare i valori di riferimento sono stati reclutati 48 donatori sani. La misurazione delle concentrazioni degli ioni cobalto (Co), cromo (Cr), nickel (Ni) e molibdeno (Mo) è stata effettuata utilizzando la spettrofotometria ad assorbimento atomico su fornace di grafite. A parte il Ni, le concentrazioni di ioni nei pazienti con MOM-HR erano più elevate rispetto ai controlli. Il rilascio di ioni Cr e Co nei pazienti con MOM-HR è risultato superiore rispetto ai soggetti con MOM-THA. Da un’analisi basata sul sesso, è emerso che nelle femmine con MOM-HR i livelli di ioni Cr e Co sono risultati significativamente aumentati rispetto alle femmine con MOM-THA. Indipendentemente dal tipo di impianto, gli accoppiamenti metallo-metallo (MOM) producono concentrazioni di ioni metallici significativamente più alte a follow-up a lungo termine rispetto a quelle osservate nei soggetti sani. Un fattore che deve essere attentamente considerato nella scelta dell’impianto, e in particolar modo nei soggetti giovani, è il cospicuo rilascio di ioni Cr e Co nella popolazione femminile con MOM-HR.

Synthesis of novel cobalt and iron complexes for sustainable catalytic hydrogenations

Aim of the present work of thesis is to synthesize new non-noble metal based complexes to be employ in redox reactions by a metal-ligand cooperative mechanism. The need of replacing toxic and expensive precious metal complexes with more available and benign metals, has led to the development of new compounds based on cobalt and iron, which are the metals investigated in this study. A carbonyl-tetrahydroborato-bis[(2-diisopropylphosphino)ethyl]amine-cobalt complex bearing a PNP-type ligand is synthesized by a three-step route. Optimization attempt of reaction route were assessed in order to lowering reaction times and solvent waste. New cobalt complex has been tested in esters hydrogenation as well as in acceptorless dehydrogenative coupling of ethanol. Other varieties of substrates were also tested in order to evaluate any possible applications. Concerning iron complex, dicarbonyl-(η4-3,4-bis(4-methoxyphenyl)-2,5-diphenylcyclopenta-2,4-dienone)(1,3-dimethyl-ilidene)iron is synthesized by a three steps route, involving transmetallation of a silver complex, derived from an imidazolium salt, to iron complex. In order to avoid solvent waste, optimization is assessed. Studies were performed to assess activity of triscarbonyl iron precursor toward imidazolium salt and silver complexes.

Bio-inspired polymer-supported nitrido molybdenum(VI) complexes for ammonia synthesis − reactivity towards protons and electrons : EPR investigations on paramagnetic molybdenum(V) and copper(II) complexes

Die biologische Stickstofffixierung durch Molybdän-haltige Nitrogenasen sowie die Erforschung des zugrundeliegenden komplexen Mechanismus (N2-Aktivierung an Metall-Zentren, 6-fache Protonierung und Reduktion, N–N Bindungsspaltung unter Bildung von Ammoniak) ist von erheblichem Interesse. Insbesondere Molybdän-Komplexe wurden bereits erfolgreich als Modellverbindungen für die Untersuchung elementarer Einzelschritte der N2-Aktivierung eingesetzt. Durch die Verwendung von Triamidoamin-Liganden ist es Schrock et al. sogar gelungen mehrere Katalysezyklen zu durchlaufen und einen Mechanismus zu formulieren. Trotz der sterisch anspruchsvollen Substituenten in den Schrock-Komplexen ist die Umsatzrate dieses homogenen Katalysators, aufgrund Komplex-Deaktivierung infolge intermolekularer Reaktionen wie Dimerisierung und Disproportionierung, limitiert. In der vorliegenden Arbeit wurden einige dieser Herausforderungen angegangen und die aktiven Spezies auf einer Festphase immobilisiert, um intermolekulare Reaktionen durch räumliche Isolierung der Komplexe zu unterdrücken.rnEin Polymer-verankertes Analogon des Schrock Nitrido-Molybdän(VI)-Komplexes wurde auf einem neuen Reaktionsweg synthetisiert. Dieser beinhaltet nur einen einzigen Reaktionsschritt, um die funktionelle Gruppe „MoN“ einzuführen. Protonierung des immobilisierten Nitrido-Molybdän(VI)-Komplexes LMoVIN (L = Polymer-verankerter Triamidoamin-Ligand) mit 2,6-Lutidinium liefert den entsprechenden Imido-Molybdän(VI)-Komplex. Durch anschließende Ein-Elektronen-Reduktion mit Cobaltocen wird der Polymer-angebundene Imido-Molybdän(V)-Komplex erhalten, bewiesen durch EPR-Spektroskopie (g1,2,3 = 1.989, 1.929, 1.902). Durch die Immobilisierung und die effektive räumliche Separation der Reaktionszentren auf der Festphase werden bimolekulare Nebenreaktionen, die oft in homogenen Systemen auftreten, unterdrückt. Dies ermöglicht zum ersten Mal die Darstellung des Imido-Molybdän(V)-Intermediates des Schrock-Zyklus.rnEPR-Spektren des als Spin-Label eingeführten immobilisierten Nitrato-Kupfer(II)-Komplexes wurden unter verschiedenen Bedingungen (Lösungsmittel, Temperatur) aufgenommen, wobei sich eine starke Abhängigkeit zwischen der Zugänglichkeit und Reaktivität der immobilisierten Reaktionszentren und der Art des Lösungsmittels zeigte. Somit wurde die Reaktivität von LMoVIN gegenüber Protonen und Elektronen, welches zur Bildung von NH3 führt, unter Verwendung verschiedener Lösungsmittel untersucht und optimiert. Innerhalb des kugelförmigen Polymers verläuft die Protonierung und Reduktion von LMoVIN stufenweise. Aktive Zentren, die sich an der „äußeren Schale“ des Polymers befinden, sind gut zugänglich und reagieren schnell nach H+/e− Zugabe. Aktive Zentren im „Inneren des Polymers“ hingegen sind schlechter zugänglich und zeigen langsame diffusions-kontrollierte Reaktionen, wobei drei H+/e− Schritte gefolgt von einer Ligandenaustausch-Reaktion erforderlich sind, um NH3 freizusetzen: LMoVIN  LMoVNH  LMoIVNH2  LMoIIINH3 und anschließender Ligandenaustausch führt zur Freisetzung von NH3.rnIn einem weiteren Projekt wurde der Bis(ddpd)-Kupfer(II)-Komplex EPR-spektroskopisch in Hinblick auf Jahn−Teller-Verzerrung und -Dynamik untersucht. Dabei wurden die EPR-Spektren bei variabler Temperatur (70−293 K) aufgenommen. Im Festkörperspektrum bei T &lt; 100 K erscheint der Kupfer(II)-Komplex als gestreckter Oktaeder, wohingegen das EPR-Spektrum bei höheren Temperaturen g-Werte aufzeigt, die einer pseudo-gestauchten oktaedrischen Kupfer(II)-Spezies zuzuordnen sind. Diese Tatsache wird einem intramolekularen dynamischen Jahn−Teller Phänomen zugeschrieben, welcher bei 100 K eingefroren wird.