468 resultados para ads
Resumo:
The adsorption kinetics curves of poly(xylylidene tetrahydrothiophenium chloride) (PTHT), a poly-p-phenylenevinylene (PPV) precursor, and the sodium salt of dodecylbenzene sulfonic acid (DBS), onto (PTHT/DBS)(n) layer-by-layer (LBL) films were characterized by means of UV-vis spectroscopy. The amount of PTHT/DBS and PTHT adsorbed on each layer was shown to be practically independent of adsorption time. A Langmuir-type metastable equilibrium model was used to adjust the adsorption isotherms data and to estimate adsorption/desorption coefficients ratios, k = k(ads)/k(des), values of 2 x 10(5) and 4 x 10(6) for PTHT and PTHT/DBS layers, respectively. The desorption coefficient has been estimated, using literature values for poly(o-methoxyaniline) desorption coefficient, as was found to be in the range of 10(-9) to 10(-6) s(-1), indicating that quasi equilibrium is rapidly attained.
Resumo:
In this paper we report here new considerations about the relationship between the mass and charge variations (m/z relationship) in underpotential deposition (UPD), bulk deposition and also in the H(2)Se formation reaction. Nanogravimetric experiments were able to show the adsorption of H(2)SeO(3) on the AuO surface prior to the voltammetric sweep and that, after the AuO reduction, 0.40 monolayer of H(2)SeO(3) remains adsorbed on the newly reduced Au surface, which was enough to gives rise to the UPD layer. The UPD results indicate that the maximum coverage with Se(ads) on polycrystalline gold surface corresponds to approximately 0.40 monolayer, in good agreement with charge density results. The cyclic voltammetry experiments demonstrated that the amount of bulk Se obtained during the potential scan to approximately 2 Se monolayers, which was further confirmed by electrochemical quartz crystal microbalance (EQCM) measurements that pointed out a mass variation corresponding of 3 monolayers of Se. In addition, the Se thin films were obtained by chronoamperometric experiments, where the Au electrode was polarized at +0.10V during different times in 1.0 M H(2)SO(4) + 1.0 mM SeO(2). The topologic aspects of the electrodeposits were observed in Atomic Force Microscope (AFM) measurements. Finally, in highly negative potential polarizations, the H(2)Se formation was analyzed by voltammetric and nanogravimetric measurements. These finding brings a new light on the selenium electrodeposition and point up to a proposed electrochemical model for molecule controlled surface engineering. (c) 2009 Elsevier Ltd. All rights reserved.
Resumo:
Direct analysis, with minimal sample pretreatment, of antidepressant drugs, fluoxetine, imipramine, desipramine, amitriptyline, and nortriptyline in biofluids was developed with a total run time of 8 min. The setup consists of two HPLC pumps, injection valve, capillary RAM-ADS-C18 pre-column and a capillary analytical C 18 column connected by means of a six-port valve in backflush mode. Detection was performed with ESI-MS/MS and only 1 mu m of sample was injected. Validation was adequately carried out using FLU-d(5) as internal standard. Calibration curves were constructed under a linear range of 1-250 ng mL(-1) in plasma, being the limit of quantification (LOQ), determined as 1 ng mL(-1), for all the analytes. With the described approach it was possible to reach a quantified mass sensitivity of 0.3 pg for each analyte (equivalent to 1.1-1.3 fmol), translating to a lower sample consumption (in the order of 103 less sample than using conventional methods). (C) 2008 Elsevier B.V. All rights reserved.
Resumo:
Carbon-supported platinum is commonly used as an anode electrocatalyst in low-temperature fuel cells fueled with methanol. The cost of Pt and the limited world supply are significant barriers for the widespread use of this type of fuel cell. Moreover, Pt used as anode material is readily poisoned by carbon monoxide produced as a byproduct of the alcohol oxidation. Although improvements in the catalytic performance for methanol oxidation were attained using Pt-Ru alloys, the state-of-the-art Pt-Ru catalyst needs further improvement because of relatively low catalytic activity and the high cost of noble Pt and Ru. For these reasons, the development of highly efficient ternary platinum-based catalysts is an important challenge. Thus, various compositions of ternary Pt(x)-(RuO(2)-M)(1-x)/C composites (M = CeO(2), MoO(3), or PbO(x)) were developed and further investigated as catalysts for the methanol electro-oxidation reaction. The characterization carried out by X-ray diffraction, energy-dispersive X-ray analysis, transmission electron microscopy, X-ray photoelectron spectroscopy, and cyclic voltammetry point out that the different metallic oxides were successfully deposited on the Pt/C, producing small and well-controlled nanoparticles in the range of 2.8-4.2 nm. Electrochemical experiments demonstrated that the Pt(0.50)(RuO(2)-CeO(2))(0.50)/C composite displays the higher catalytic activity toward the methanol oxidation reaction (lowest onset potential of 207 mV and current densities taken at 450 mV, which are 140 times higher than those at commercial Pt/C), followed by the Pt(0.75)(RuO(2)-MoO(3))(0.25)/C composite. In addition, both of these composites produced low quantities of formic acid and formaldehyde when compared to a commercially available Pt(0.75)-Ru(0.25)/C composite (from E-Tek, Inc.), suggesting that the oxidation of methanol occurs mainly by a pathway that produces CO(2) forming the intermediary CO(ads).
Resumo:
This degree project includes both a theoretic component and a practical component within the graphicprofiling domain. Literature on graphic design has been studied for the theoretical part and the achievedknowledge has been used for the practical part. The project has been to produce graphic materialfor “Rookiefestivalen” in Hultsfred.In modern society it is important for a corporation to distinguish itself from others by using a graphicprofile. Through using a graphic profile the company can have an affect on how it is perceived byothers. This is true not only for corporations as both organisations, societies and other events will benefitfrom the use of a graphic profile.The material that’s been produced is not within the traditional boundaries of graphic profiling. It israther marketing material for the festival. The graphic profile was applied to a variety of things suchas posters, flyers, ad’s and the festival’s website. The result is to be seen in the appendix of this degreeproject and on the Internet: http://www.rookierockparty.se
Resumo:
Tidigare studier som gjorts inom området visade att kvinnor anser att kvinnors skönhet inte är värderad enligt rimliga normer i vårt samhälle. Hård retuschering motarbetas på många håll, bland annat genom att organisationer som ASA (Advertising Standards Authority) och politiska partier som Liberaldemokraterna i Storbritannien arbetar för att missledande retuschering ska försvinna. En studie har visat att det, för att öka annonsers attraktionskraft, är viktigt att den ökade skönheten hos en modell är relevant för produktens användningsområde, då betraktaren anstränger sig intellektuellt vid betraktandet av bilden. Det finns dock inga tidigare studier som bevisar om en retuscherad modell faktiskt ökar målgruppens köplust av skönhetsprodukter vid rådande samhällsattityder och skönhetsideal. Två enkätundersökningar gjordes därför med sammanlagt 1480 deltagare. Produkten i studien var en fiktiv hudkräm. Genom att i den ena undersökningen låta betraktaren möta modellbilden i en situation som efterliknade verkligheten, på så sätt att de inte fick veta om den var retuscherad, kunde studien svara på om retuschering ökade köplusten. Bilder med bortretuscherade skönhetsfläckar och utväxt prefererades. Att retuschera bort flyghår ökade inte köplusten. I den andra jämförande undersökningen kunde betraktaren jämföra den retuscherade med den oretuscherade modellbilden. Resultaten visade att skönhetsfläckar och flyghår tillåts och prefereras borttagna, men inte utväxt. I intervjuer med fem kvinnor hördes målgruppens attityder om vad som ansågs var tillåtet att retuschera. Svaren tydde på att en relevant och försiktig retuschering prefererades. Att lämna några födelsemärken ökade trovärdigheten.
Resumo:
Etik kring bilder i annonser har diskuterats mycket, speciellt modell-, ochproduktbilder har kritiserats. Det tycks dock saknas forskning om acceptanskring efterbehandling av landskapsfotografier som ofta används vidmarknadsföring av turistmål. En webbenkätundersökning genomfördes medbildexempel för att undersöka vilken nivå av efterbehandling som ansågsverklighetstrogen, tilltalande och accepterbar i sådana annonser. Slutsatsenblev att fotografier där exponeringen korrigerats för att skapa en tydligare bildvar det mest accepterade. Skillnader i åsikter mellan åldrar, kön, de som haroch inte har tidigare erfarenhet av fotografi och retuschering diskuterades ochdet visade sig att kvinnor och de utan tidigare erfarenhet var lite mer kritiskatill efterbehandling. Det framkom att en del betraktare kan accepteraytterligare efterbehandling om den genomförs för att sälja en specifik känslaoch så länge inte betraktaren kan känna sig vilseledd.
Resumo:
Sexism och könsdiskriminering är ämnen som idag exponeras mycket i media. De tar stor plats och bäddar för diskussion både i sociala medier och i verkligheten. Beträffande könsdiskriminering i reklam är det oftast fall där kvinnor är utsatta för stereotypisk porträttering och objektifiering som leder till en offentlig debatt, men de senaste åren har visat på att liknande fall för män ökar. Denna kvalitativa studie har som syfte att undersöka och kartlägga utförandet av könsdiskriminering i svenska annonser i en visuell innehållsanalys, för att sedan jämföra vad som särskiljer friade och fällda fall. Reklamombudsmannens kriterier för könsdiskriminerande reklam ligger till grund för bedömande av material, samt definiering av analysens kategorier. I både friade och fällda fall visade sig bildens utformning och de porträtterade personerna vara av högsta relevans och motiv för att anmäla eller döma en annons för könsdiskriminering. Resultatet visade på att förekomsten av objektifierande reklam uppmärksammas och fälls mer än schabloniserande reklam, samt att annonser som visade större exponering av hud inte nödvändigtvis var den som fälldes mest då flera av fallen visade en tydlig koppling till den marknadsförda produkten.
Resumo:
O processo de desenvolvimento de software implica na necessidade constante de tomadas de decisão. A cada etapa do processo, torna-se necessário estabelecer a comunicação e interação entre usuários, gerentes, analistas, programadores e mantenedores numa constante troca de informações. O registro dos artefatos produzidos durante todo o processo é uma questão que norteia as pesquisas em ambiente de desenvolvimento de software. Quando se fala em suporte ao processo de colaboração entre os elementos de uma equipe de desenvolvimento, este registro torna-se ainda mais necessário. Neste contexto, a modelagem dos dados a serem armazenados se amplia para comportar outras informações provenientes da interação do grupo além dos artefatos gerados. As informações trocadas durante este processo interativo que incluem fatos, hipóteses, restrições, decisões e suas razões, o significado de conceitos e, os documentos formais formam o que é denominado pela literatura especializada como memória de grupo. A proposta da arquitetura SaDg PROSOFT visa fornecer suporte a memória de grupo, no que diz respeito ao registro das justificativas de projeto(Design Rationale), através de uma integração com o gerenciador de processos (GP) provido pelo ADS PROSOFT. Esta integração se dá através das ferramentas inseridas no modelo, assim desenhadas: Editor de Norma, Editor de Argumentação, Extrator de Alternativas, Editor de Votação. O ADS PROSOFT integra ferramentas para desenvolvimento de software. Este ADS foi escolhido para o desenvolvimento do modelo SADG, pois baseia-se na construção formal de software, mas particularmente no método algébrico, por ser um ambiente estendível, possibilitando a inclusão do modelo SaDg PROSOFT ao seu conjunto de ferramentas, por ter características de um ambiente distribuído e cooperativo e por não dispor de nenhum suporte à discussões e decisões em grupos. São apresentados os fundamentos de modelos SADG e algumas ferramentas. Alguns dos principais requisitos desses ambientes foram coletados e são apresentados a fim de embasar a proposta do trabalho. O modelo SADG é apresentado na forma de ferramentas PROSOFT(chamadas ATOs) e permite a definição de atividades como: Atividade de argumentação, atividade de extração e a atividade de votação. Além disso, permite a coordenação destas atividades através de um facilitador e do próprio GP, e também, possui um mecanismo para a configuração do processo decisório.
Resumo:
A crescente complexidade das aplicações, a contínua evolução tecnológica e o uso cada vez mais disseminado de redes de computadores têm impulsionado os estudos referentes ao desenvolvimento de sistemas distribuídos. Como estes sistemas não podem ser facilmente desenvolvidos com tecnologias de software tradicionais por causa dos limites destas em lidar com aspectos relacionados, por exemplo, à distribuição e interoperabilidade, a tecnologia baseada em agentes parece ser uma resposta promissora para facilitar o desenvolvimento desses sistemas, pois ela foi planejada para suportar estes aspectos, dentre outros. Portanto, é necessário também que a arquitetura dos ambientes de desenvolvimento de software (ADS) evolua para suportar novas metodologias de desenvolvimento que ofereçam o suporte necessário à construção de softwares complexos, podendo também estar integrada a outras tecnologias como a de agentes. Baseada nesse contexto, essa dissertação tem por objetivo apresentar a especificação de uma arquitetura de um ADS distribuído baseada em agentes (DiSEN – Distributed Software Engineering Environment). Esse ambiente deverá fornecer suporte ao desenvolvimento de software distribuído, podendo estar em locais geograficamente distintos e também os desenvolvedores envolvidos poderão estar trabalhando de forma cooperativa. Na arquitetura proposta podem ser identificadas as seguintes camadas: dinâmica, que será responsável pelo gerenciamento da (re)configuração do ambiente em tempo de execução; aplicação, que terá, entre os elementos constituintes, a MDSODI (Metodologia para Desenvolvimento de Software Distribuído), que leva em consideração algumas características identificadas em sistemas distribuídos, já nas fases iniciais do projeto e o repositório para armazenamento dos dados necessários ao ambiente; e, infra-estrutura, que proverá suporte às tarefas de nomeação, persistência e concorrência e incorporará o canal de comunicação. Para validar o ambiente será realizada uma simulação da comunicação que pode ser necessária entre as partes constituintes do DiSEN, por meio da elaboração de diagramas de use case e de seqüência, conforme a notação MDSODI. Assim, as principais contribuições desse trabalho são: (i) especificação da arquitetura de um ADS distribuído que poderá estar distribuído geograficamente; incorporará a MDSODI; proporcionará desenvolvimento distribuído; possuirá atividades executadas por agentes; (ii) os agentes identificados para o DiSEN deverão ser desenvolvidos obedecendo ao padrão FIPA (Foundation for Intelligent Physical Agents); (iii) a identificação de um elemento que irá oferecer apoio ao trabalho cooperativo, permitindo a integração de profissionais, agentes e artefatos.
Resumo:
Este trabalho apresenta uma arquitetura para Ambientes de Desenvolvimento de Software (ADS). Esta arquitetura é baseada em produtos comerciais de prateleira (COTS), principalmente em um Sistema de Gerência de Workflow – SGW (Microsoft Exchange 2000 Server – E2K) - e tem como plataforma de funcionamento a Internet, integrando também algumas ferramentas que fazem parte do grande conjunto de aplicativos que é utilizado no processo de desenvolvimento de software. O desenvolvimento de um protótipo (WOSDIE – WOrkflow-based Software Development Integrated Environment) baseado na arquitetura apresentada é descrito em detalhes, mostrando as etapas de construção, funções implementadas e dispositivos necessários para a integração de um SGW, ferramentas de desenvolvimento, banco de dados (WSS – Web Storage System) e outros, para a construção de um ADS. O processo de software aplicado no WOSDIE foi extraído do RUP (Rational Unified Process – Processo Unificado Rational). Este processo foi modelado na ferramenta Workflow Designer, que permite a modelagem dos processos de workflow dentro do E2K. A ativação de ferramentas a partir de um navegador Web e o armazenamento dos artefatos produzidos em um projeto de software também são abordados. O E2K faz o monitoramento dos eventos que ocorrem dentro do ambiente WOSDIE, definindo, a partir das condições modeladas no Workflow Designer, quais atividades devem ser iniciadas após o término de alguma atividade anterior e quem é o responsável pela execução destas novas atividades (assinalamento de atividades). A arquitetura proposta e o protótipo WOSDIE são avaliados segundo alguns critérios retirados de vários trabalhos. Estas avaliações mostram em mais detalhes as características da arquitetura proposta e proporcionam uma descrição das vantagens e problemas associados ao WOSDIE.
Resumo:
Esta pesquisa investiga empiricamente o que aconteceu com a função e a carreira de Organização e Métodos (O&M) nas empresas no Brasil desde 1985. O estudo procura verificar empiricamente se, como afirmam alguns autores, desde os prósperos anos 70 e 80, O&M teria passado por um processo de transformação até seu virtual desaparecimento nas empresas atuais. Primeiro, investiga-se o destino da função entre 1985 e 1997, em uma amostra de 60 empresas paulistas, via questionários. Segundo, levanta-se a oferta de posições em O&M (comparada com outras áreas) no período, via evolução de anúncios de empregos em jornal paulista.
Resumo:
This research has aimed to study the ethical patterns that guide the managers or owners of advertising agencies in Brazil and in other forty-two countries. Their knowledge or affinity to the concepts of ethics may indicate the degree of responsibility that they assume when dealing with the communication over products, services and ideas, in all of the different markets throughout the world. The comparative analysis of the opinions gathered in the research, in relation to several ethics parameters, has led to the observation that the codes of ethics do not seem to be sufficient to inform an advertising professional with respect to all of the situations and issues he deals with. A more profound knowledge of Ethics fundamental principles over nature and commercial life becomes mandatory, in order to reduce the uncertainties in a moral decision making process. Besides the questionnaires sent to professionals, data related to ads in national and foreign magazines were gathered in several institutions. The monitoring of ads in radio, television and outdoors allowed the evaluation of ongoing ethical parameters in Brazil as far as these communication means.
Resumo:
In the actual competitive scenario the higher education institutions have been forced to become more active in recruiting students due to the reduction in candidates for its courses. Print advertising are important components in the educational services communications campaigns and, thus, they are an important focus of research. The literature on services communication suggests that the use of cues, as the installations picture and testimonial, presents an observable way to tangibilize educational services offers. We relate the cue paradigm theory as evaluative indicators of a product, with two of the four advertising strategies, with the objective to investigate the impact of the cues in the printed educational services ad¿s in relation to the consumers attitudes. More specifically, to investigate the impact of the physical representation strategy (installations picture - an intrinsic cue), and the association strategy (testimonial - an extrinsic cue), in the consumers attitudes toward the advertisement, the brand and the purchase intention. With this purpose an experiment between subjects with 123 students was carried through, with four levels of manipulation. In relation to consumer attitudes, none of the analyzed strategies presented a significative superiority in relation one with another. However, the subjects with low involvement in the value/auto-image dimension had presented more favorable attitudes in relation to the purchase intention in the presence of the advertising using a testimonial (association strategy - an extrinsic cue).
Resumo:
A ética na propaganda tem sido analisada do ponto de vista dos anunciantes e das agências. Pouco, no entanto, se encontra no tocante à ótica do consumidor. A presente tese tem como objetivo analisar a opinião dos consumidores a respeito de comerciais veiculados na televisão, à luz do direito natural, do Código de Defesa do Consumidor e do código de Auto-Regulamentação Publicitária. o estudo exploratório serve de base para estudos ulteriores, que se fazem necessários e urgentes, tendo em vista·a formação ética de um enorme contingente de jovens existentes no País.