Operational characteristics of four metering systems for agricultural fertilizers and amendments

The use of fertilizers and solid amendments in agriculture generates special interest for their effect on crop productivity, as well as for their environmental impact. The efficient use of these products demands knowing their physical and mechanical properties, the storing conditions effect and the operational characteristics of the metering systems used in the fertilizing equipment. In this context, the present study was developed with the purpose of evaluating the operational characteristics of different fertilizing metering systems and to determine the adequate metering system-product operational parameters, using powder lime, powder gypsum, granular 10-30-10 (N-P-K), and granular urea. Operational differences were established among four types of commercial fertilizer metering systems, including wire auger, star-shaped feed wheel, feed screw and ridged traction wheel. The study found that the unloading rate depends directly on the fertilizer metering system's rotating speed and is affected by particle size, repose angle, bulk density and moisture content of the applied product. The wire auger and star-shaped feed wheel metering systems were adequate for the distribution of powder products and the feed screw for granulated fertilizers. Furthermore, theoretical and experimental characteristic equations were established, defining curves for calibration and handling of the products plus the rotating speed range in which a better distributing behavior was achieved.

Operational performance of the mechanized and semi-mechanized potato harvest

Potato is an important crop plant throughout the world. Harvesting is a fundamental step in its production system. Maybe, it is the most complex and expensive operation. Thus, the objective of this work was to compare the cost of the mechanized and semi-mechanized harvest, the operational capacity and the production losses during the potato harvest process. The work was accomplished in a commercial farming, cultivated under pivot system, in the municipal district of Perdizes - MG, Brazil. A completely randomized design with two treatments was used: mechanized and semi-mechanized harvest. The mechanized harvest used a self-propelled harvester. In the semi-automated harvest, a digger mounted on tractor was used and the potato was manually harvested. It was concluded that the cost of mechanized harvest was 49.03% lower than the cost of semi-mechanized harvest. On average, the harvester had a work for 23 workers in manual harvest. Mechanized harvest showed losses of 2.35% of potato yield, while the semi-mechanized harvest showed losses of 6.32%.

Operational parameters of soybean seeding in santa fe system

The use of no tillage system associated with the crop-livestock integration is an alternate managing that promotes the accumulation of dry matter in the soil, an essential fact to make the system sustainable and profitable. The aim of this study was to evaluate the operational performance of a planter-tractor set on maize straws intercropped with Urochloa, in different seeding modes. The soybean crop was seed on the intercropping of two forage species (Urochloa brizantha and Urochloa ruziziensis) in five cropping systems: MBL (Maize with Urochloa in the maize seeding row, mixed with base fertilizer and deposited at 0.10 m), MBE (Maize with Urochloa seeded between rows at the same day of seeding maize), MBC (Urochloa between rows of maize seeded with the covering fertilizer at the V4 stage), MBLA (Maize with Urochloa by broadcast seeding at the V4 stage ) and MS (Single Maize: control). The following variables were evaluated: dry mass of maize straw, dry mass of forages and total dry mass of straw; and for the operational parameters the speed of seeding, wheel slippage, traction force and average power at the drawbar. The results showed that the amount of straw produced by maize intercropping with Urochloa, interferes in the operational performance of the tractor-planter at the operation of soybean seeding, i.e., areas with higher amount of straw promote greater energy demand, as well as higher wheel slippage.

Energy demand in citrus production under varied operational efficiency values

Citrus orchards are very important in Brazil, especially in São Paulo State, where occupy an area of 600,000 ha approximately. To identify sustainability degree of citrus production system, an energy analysis allows evaluating efficiency of direct and indirect applied inputs. Thus, this study aimed to evaluate citrus production system under energetic point of view, in which invested energy is paid back with citrus production; being compared within three scenarios for operational field efficiency. As result, by sensitivity analysis was determined that fuel was the main energy demander, followed by pesticides and fertilizers. In operational work capacity analysis, all combinations between efficiency (minimum, typical and maximum) and yield levels became positive in the seventh year, except for the combination minimum efficiency and 10 % less yield, positive in the eighth year. The best combination (maximum efficiency and 10 % more yield) has promoted investment payoff around the sixth and seventh year. By this study, it is possible to determine the total energy demand to produce citrus and indentify the applied inputs that need more attention by the decision-makers. Labor and seedlings can be ommited for further studies with citrus, since they were irrelevant. Management of agricultural machinery may pose an important role on decreasing environmental impact of citrus production.

The effect of dynamic capabilities on operational-level innovation – Empirical study in magazine publishing industry

This master’s thesis aims to examine the relationship between dynamic capabilities and operational-level innovations. In addition, measures for the concept of dynamic capabilities are developed. The study was executed in the magazine publishing industry which is considered favourable for examining dynamic capabilities, since the sector is characterized by rapid change. As a basis for the study and the measure development, a literary review was conducted. Data for the empirical section was gathered by a survey targeted to chief-editors of Finnish consumer magazines. The relationship between dynamic capabilities and innovation was examined by multiple linear regression. The results indicate that dynamic capabilities have effect on the emergence of radical innovations. Environmental dynamism’s effect on radical innovations was not detected. Also, dynamic capabilities’ effect on innovation was not greater in turbulent operating environment.

Working capital management in the small and medium-sized enterprises Case: Project-based business environment in Flowrox Oy

This Master´s thesis illustrates how growing a business ties up the company´s working capital and what the cost of committed capital. In order to manage a company´s working capital in rapid business growth phase, the thesis suggests that by monitoring and managing the operating and cash conversion cycles of customers´ projects, a company can find ways to secure the required amount of capital. The research method of this thesis was based on literature reviews and case study research. The theoretical review presents the concepts of working capital and provides the background for understanding how to improve working capital management. The company in subject is a global small and medium-sized enterprise that manufactures pumps and valves for demanding process conditions. The company is expanding, which creates lots of challenges. This thesis concentrates to the company´s working capital management and its efficiency through the supply chain and value chain perspective. The main elements of working capital management are inventory management, accounts receivable management and accounts payable management. Prepayments also play a significant role, particularly in project-based businesses. Developing companies´ working capital management requires knowledge from different kind of key operations´ in the company, like purchasing, production, sales, logistics and financing. The perspective to develop and describe working capital management is an operational. After literature reviews the thesis present pilot projects that formed the basis of a model to monitor working capital in the case company. Based on analysis and pilot projects, the thesis introduces a rough model for monitoring capital commitments in short time period. With the model the company can more efficiently monitor and manage their customer projects.

Tuotanto- ja pakkausmateriaalien varastojen nykytila ja kehittäminen lääkeannostelijoita valmistavassa tehtaassa

Diplomityön tarkoituksena oli selvittää lääkeannostelijoita valmistavan tehtaan materiaalivarastojen nykytila. Varaston nykytila-analyysi jaettiin pääoma- ja operatiivisen tehokkuuden arviointiin. Työssä haluttiin kartoittaa toimenpide-ehdotuksia varastonohjauksen tehostamiseksi. Diplomityön tarkoituksena oli myös lisätä avainhenkilöiden ymmärrystä koskien varastojen pidon vaikutuksia yrityksen liiketoimintaan. Varastojen nykytila voitiin kiteyttää suureen pääoman sitoutumiseen, hitaisiin kiertoaikoihin sekä tehokkaan työskentelyn kannalta liian pieniin ja ahtaisiin varastoihin. Kustannuksia ei ole otettu kokonaisuudessaan huomioon tilattaessa ja varastoitaessa materiaalia. Varaston hitaita kiertonopeuksia ei ole tunnistettu vaikuttajina yrityksen tulokseen ja kannattavuuteen. Jotta varastonohjaus- ja hankintaprosesseja voitaisiin tehostaa, pitäisi ostotoimintoihin tehdä muutoksia. Tilausrytmiä ja –määriä täytyisi harkita uudelleen, jotta voitaisiin vähentää varastoihin sitoutuvan pääoman määrää. Informaationvirtaa tehtaalla sekä organisaatiorajojen yli pitäisi parantaa, jotta voitaisiin vähentää kysynnän heilahteluja sekä siihen varautumista. Varmuusvarastojen pidosta saatavien korvausten olisi katettava koko materiaalin kiertoajan aikana syntyvät varastoinnin kustannukset.

Structural and operational optimisation : applications in energy systems

In this work mathematical programming models for structural and operational optimisation of energy systems are developed and applied to a selection of energy technology problems. The studied cases are taken from industrial processes and from large regional energy distribution systems. The models are based on Mixed Integer Linear Programming (MILP), Mixed Integer Non-Linear Programming (MINLP) and on a hybrid approach of a combination of Non-Linear Programming (NLP) and Genetic Algorithms (GA). The optimisation of the structure and operation of energy systems in urban regions is treated in the work. Firstly, distributed energy systems (DES) with different energy conversion units and annual variations of consumer heating and electricity demands are considered. Secondly, district cooling systems (DCS) with cooling demands for a large number of consumers are studied, with respect to a long term planning perspective regarding to given predictions of the consumer cooling demand development in a region. The work comprises also the development of applications for heat recovery systems (HRS), where paper machine dryer section HRS is taken as an illustrative example. The heat sources in these systems are moist air streams. Models are developed for different types of equipment price functions. The approach is based on partitioning of the overall temperature range of the system into a number of temperature intervals in order to take into account the strong nonlinearities due to condensation in the heat recovery exchangers. The influence of parameter variations on the solutions of heat recovery systems is analysed firstly by varying cost factors and secondly by varying process parameters. Point-optimal solutions by a fixed parameter approach are compared to robust solutions with given parameter variation ranges. In the work enhanced utilisation of excess heat in heat recovery systems with impingement drying, electricity generation with low grade excess heat and the use of absorption heat transformers to elevate a stream temperature above the excess heat temperature are also studied.

Improving the inventory management and valuation process, Case: The Switch Drive Systems

The goal of this study is to create a new inventory valuation process for The Switch Drive Systems and to improve its inventory management practices. In the matter of inventories the main problems in the case company are that it doesn’t have consistent valuation methods throughout the company and that information received in ERP system isn’t trustful. The research is qualitative case study. The empirical data is gathered through observing and unstructured interviews. The research shows that material flow process and the inventory valuation must be divided and handled separately but they should interact with each other. The result is a new inventory valuation process which takes many factors of material process under the consideration in order to receive reliable value for inventories.

Towards Inter-organizational Working Capital Management

Working capital is an investment which is tied up into the inventories and accounts receivable and which is released with accounts payable. Due to the current business landscape with tightened financial conditions and finance markets, organizations emphasize efficient working capital management. With efficient working capital management, a company can reduce the need of finance, free up cash, increase profitability, improve liquidity, increase the efficiency of operations, and decrease (financing) costs. From the perspective of an individual company, efficient working capital management means decreasing inventory levels by shortening the cycle time of inventories, decreasing accounts receivable by shortening the trade credit terms and effective collection procedures, and increasing the level of accounts payable by paying the suppliers later. From an inter-organizational perspective, however, working capital should not be sub-optimized by a single company but holistic view to working capital management through the supply chain should be adopted to create value and improve performance together. The purpose of this research is to take academic research as well as practical management towards inter-organizational working capital management. The thesis discusses the benefits as well as mechanisms of working capital management in the inter-organizational context and has two main objectives: (1) to examine the effect of inter-organizational working capital management on performance in the value chain context and (2) to develop models of working capital management for internal as well as inter-organizational value chains. The results of the archival research conducted in the value chain of the pulp and paper industry and the value chain of the automotive industry indicate that companies can increase relative profitability by managing working capital comprehensively by taking into account all three components, and holistically though the value chain. Companies in the value chain benefit from different strategies in working capital management depending on the position of the company in the value chain. This can be taken into account in inter-organizational working capital management. The effects of inter-organizational working capital management actions on the financing costs of working capital were studied via simulations. Simulations also show that the value chain and individual companies benefit from an inter-organizational view to working capital management. Inter-organizational working capital management actions include for example: shortening the cycle time of inventories, reducing product costs, shifting inventories, shortening payment terms, and considering the cost of capital. The thesis also provides solutions for the practical requirements for tools to control working capital. The design science part of the research introduces the adjusted cash conversion cycle (ACCC) model for internal value chains, as well as models for working capital management in the inter-organizational value chain context: the working capital management model (WCMM) and the financial cycle time model (FCTM) designed in corporation and product levels respectively. This research contributes to literature on working capital management and interorganizational accounting. The research gives a holistic, inter-organizational view to the management of working capital. It advances the knowledge in working capital management on operational level, increases knowledge in the recently risen theme of supply chainoriented, collaborative working capital management, combines management accounting research with supply chain management research, and contributes to the demand of practical inter-organizational accounting methods. In addition, the research has strong practical focus as new managerial methods are introduced.

Automatic traffic sign inventory- and condition analysis

This thesis researches automatic traffic sign inventory and condition analysis using machine vision and pattern recognition methods. Automatic traffic sign inventory and condition analysis can be used to more efficient road maintenance, improving the maintenance processes, and to enable intelligent driving systems. Automatic traffic sign detection and classification has been researched before from the viewpoint of self-driving vehicles, driver assistance systems, and the use of signs in mapping services. Machine vision based inventory of traffic signs consists of detection, classification, localization, and condition analysis of traffic signs. The produced machine vision system performance is estimated with three datasets, from which two of have been been collected for this thesis. Based on the experiments almost all traffic signs can be detected, classified, and located and their condition analysed. In future, the inventory system performance has to be verified in challenging conditions and the system has to be pilot tested.

Development of an operational substrate for ZapA, a metalloprotease secreted by the bacterium Proteus mirabilis

The protease ZapA, secreted by Proteus mirabilis, has been considered to be a virulence factor of this opportunistic bacterium. The control of its expression requires the use of an appropriate methodology, which until now has not been developed. The present study focused on the replacement of azocasein with fluorogenic substrates, and on the definition of enzyme specificity. Eight fluorogenic substrates were tested, and the peptide Abz-Ala-Phe-Arg-Ser-Ala-Ala-Gln-EDDnp was found to be the most convenient for use as an operational substrate for ZapA. A single peptide bond (Arg-Ser) was cleaved with a Km of 4.6 µM, a k cat of 1.73 s-1, and a catalytic efficiency of 376 (mM s)-1. Another good substrate for ZapA was peptide 6 (Abz-Arg-Pro-Pro-Gly-Phe-Ser-Pro-Phe-Arg-Gln-EDDnp) which was cleaved at a single bond (Phe-Ser) with a Km of 13.6 µM, a k cat of 3.96 s-1 and a catalytic efficiency of 291 (mM s)-1. The properties of the amino acids flanking the scissile bonds were also evaluated, and no clear requirement for the amino acid residue at P1 was found, although the enzyme seems to have a preference for a hydrophobic residue at P2.

Psychometric properties of the Portuguese version of the State-Trait Anxiety Inventory applied to college students: factor analysis and relation to the Beck Depression Inventory

The psychometric properties of the Portuguese version of the trait form of the State-Trait Anxiety Inventory (STAI-T) and its relation to the Beck Depression Inventory (BDI) were evaluated in a large Brazilian college student sample containing 845 women and 235 men. STAI-T scores tended to be higher for women, singles, those who work, and subjects under 30 years. Factor analysis of the STAI-T for total sample and by gender yielded two factors: the first representing a mood dimension and the second being related to worrying or cognitive aspects of anxiety. In order to study the relation between anxiety and depression measures, factor analysis of the combination of the 21 BDI items and the 20 STAI-T items was also carried out. The analysis resulted in two factors that were analyzed according to the tripartite model of anxiety and depression. Most of the BDI items (measuring positive affectivity and nonspecific symptoms of depression) were loaded on the first factor and four STAI-T items that measure positive affectivity. The remaining STAI-T items, all of them measuring negative affect, remained in the second factor. Thus, factor 1 represents a depression dimension and factor 2 measures a mood-worrying dimension. The findings of this study suggest that, although widely used as an anxiety scale, the STAI-T in fact measures mainly a general negative affect.

A Portuguese version of the Christo Inventory for Substance-Misuse Services: a simple outcome evaluation tool

The Christo Inventory for Substance-Misuse Services (CISS) is a single page outcome evaluation tool completed by drug alcohol service workers either on the basis of direct client interviews or of personal experience of their client supplemented by existing assessment notes. It was developed to assist substance misuse services to empirically demonstrate the effectiveness of their treatments to their respective funding bodies. Its 0 to 20 unidimensional scale consists of 10 items reflecting clients' problems with social functioning, general health, sexual/injecting risk behavior, psychological functioning, occupation, criminal involvement, drug/alcohol use, ongoing support, compliance, and working relationships. Good reliability and validity has already been demonstrated for the CISS [Christo et al., Drug and Alcohol Dependence 2000; 59: 189-197] but the original was written in English and a Portuguese version is presented here. The present review explores its applicability to a Brazilian setting, summarizes its characteristics and uses, and describes the process of translation to Portuguese. A pilot study conducted in a substance misuse service for adolescents indicated it is likely to be suitable for use among a Brazilian population. The simplicity, flexibility and brevity of the CISS make it a useful tool allowing comparison of clients within and between many different service settings.