Impact of the Meteorology Conditions on the Particulate Matter Dispersion from an Industrial Complex into Urban and Suburban Areas

The aim of this work was to assess the influence of meteorological conditions on the dispersion of particulate matter from an industrial zone into urban and suburban areas. The particulate matter concentration was related to the most important meteorological variables such as wind direction, velocity and frequency. A coal-fired power plant was considered to be the main emission source with two stacks of 225 m height. A middle point between the two stacks was taken as the centre of two concentric circles with 6 and 20 km radius delimiting the sampling area. About 40 sampling collectors were placed within this area. Meteorological data was obtained from a portable meteorological station placed at approximately 1.7 km to SE from the stacks. Additional data was obtained from the electrical company that runs the coal power plant. These data covers the years from 2006 to the present. A detailed statistical analysis was performed to identify the most frequent meteorological conditions concerning mainly wind speed and direction. This analysis revealed that the most frequent wind blows from Northwest and North and the strongest winds blow from Northwest. Particulate matter deposition was obtained in two sampling campaigns carried out in summer and in spring. For the first campaign the monthly average flux deposition was 1.90 g/m2 and for the second campaign this value was 0.79 g/m2. Wind dispersion occurred predominantly from North to South, away from the nearest residential area, located at about 6 km to Northwest from the stacks. Nevertheless, the higher deposition fluxes occurred in the NW/N and NE/E quadrants. This study was conducted considering only the contribution of particulate matter from coal combustion, however, others sources may be present as well, such as road traffic. Additional chemical analyses and microanalysis are needed to identify the source linkage to flux deposition levels.

The determinants of trade credit: a study of portuguese industrial companies

Despite the relevance of trade credit as a source of business financing, the topic is far from being considered exhausted, especially because there is no general and integrated theory explaining the causes and consequences of trade credit.Our research aims to contribute towards the literature that studies the determinants for granting and receiving trade credit. In this sequence, the present study seeks to empirically test some theories about the reasons why companies grant and receive commercial credit. For this purpose we apply a fixed effect model to a panel of 11 040 Portuguese industrial companies, of which 360 are large companies and the majority 10 680 are Small and Medium Enterprises (SME) for the period between 2003 and 2009. We conclude that large companies (with greater access to credit market) serve as financial intermediaries to their clients with less access to finance. In addition, it was observed that the supplier companies use trade credit as a legal means of price discrimination. Finally, financially constrained enterprises, especially in times of financial crisis, use commercial credit as an alternative source of funding, endorsing the hypothesis of substitution between trade credit and bank credit.

25 kV bipolar solid-state Marx generator for industrial food applications

The preliminary results from a bipolar industrial solidstate based Marx generator, developed for the food industry, capable of delivering 25 kV/250 A positive and negative pulses with 12 kW average power, are presented and discussed. This modular topology uses only four controlled switches per cell, 27 cells in total that can be charged up to 1000V each, the two extra cells are used for droop compensation. The triggering signals for all the switches are generated by a FPGA. Considering that biomaterials are similar to resistive type loads, experimental results from this new bipolar 25 kV modulator into resistive loads are presented and discussed.

Control of predators in industrial scale microalgae cultures with Pulsed Electric Fields.

This work describes the utilization of Pulsed Electric Fields to control the protozoan contamination of a microalgae culture, in an industrial 2.7m3 microalgae photobioreactor. The contaminated culture was treated with Pulsed Electric Fields, PEF, for 6h with an average of 900V/cm, 65μs pulses of 50Hz. Working with recirculation, all the culture was uniformly exposed to the PEF throughout the assay. The development of the microalgae and protozoan populations was followed and the results showed that PEF is effective on the selective elimination of protozoa from microalgae cultures, inflicting on the protozoa growth halt, death or cell rupture, without affecting microalgae productivity. Specifically, the results show a reduction of the active protozoan population of 87% after 6h treatment and 100% after few days of normal cultivation regime. At the same time, microalgae growth rate remained unaffected. © 2014 Elsevier B.V.

Estágio nas Edições Colibri. Uma editora "familiar" de produção (quase) industrial

Relatório de Estágio apresentado para cumprimento dos requisitos necessários à obtenção do grau de Mestre em Edição de Texto

Projecto de desenvolvimento e actividades do sector de higiene e segurança alimentar do gabinete do partido médico veterinário da Câmara Municipal do Seixal

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Tecnologia e Segurança Alimentar

O Sector do leite e produtos lácteos na perspectiva da segurança alimentar

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Tecnologia e Segurança Alimentar

Conceção e implementação do método das secções homogéneas numa empresa industrial de metalomecânica

Trabalho de projeto apresentado ao Instituto Superior de Contabilidade e Administração do Porto para a obtenção do grau de Mestre em Contabilidade e Finanças, sob a orientação do Mestre Paulino Manuel Leite da Silva

Dimensionamento de um edifício misto de ensacagem a construir numa instalação industrial

Trabalho de Projeto para obtenção do grau de Mestre em Engenharia Civil Estruturas

Dimensionamento de um edifício metálico de ensacagem a construir numa instalação industrial

Trabalho de Projeto para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Estruturas

Identificação, avaliação e controlo de riscos numa empresa da indústria dos colchões

Relatório de Estágio

Intelligent decision support systems for collaboration in industrial plants

Dissertação apresentada para obtenção do Grau de Doutor em Sistemas de Informação Industriais, Engenharia Electrotécnica, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

A problemática da higiene, segurança e saúde no trabalho em contexto hospitalar

Dissertação de Mestrado em Gestão Integrada da Qualidade, Ambiente e Segurança