Effect of post-weld-annealing on the tensile deformation characteristics of laser-welded NiTi thin foil

Laser welding is an important process for fabricating complex components involving NiTi shape memory
alloy. As welding is a thermal process, the amount of heat input and the rate of cooling have significant
impact on the microstructure and hence the resultant characteristics of NiTi. In this study, the effect of
laser welding and post-weld-annealing from 573 K to 1173 K on the thermal phase transformation behaviors,
tensile deformation and micro-hardness characteristics of the laser-welded NiTi thin foils were investigated.
It was found that the as-welded sample exhibited inferior super-elasticity compared to the base
material, and the super-elasticity could be partially restored by annealing at 573 K. On the other hand,
annealing of the weldment above the recrystallization temperature would lower the super-elasticity.

Microstructure evolution of 6061 O Al alloy during ultrasonic consolidation:An insight from electron backscatter diffraction

6061 O Al alloy foils were welded to form monolithic and SiC fibre-embedded samples using the ultrasonic consolidation (UC) process. Contact pressures of 135, 155 and 175 MPa were investigated at 20 kHz frequency, 50% of the oscillation amplitude, 34.5 mm s sonotrode velocity and 20 °C. Deformed microstructures were analysed using electron backscatter diffraction (EBSD). At all contact pressures deformation occurs by non-steady state dislocation glide. Dynamic recovery is active in the upper and lower foils. Friction at the welding interface, instantaneous internal temperatures (0.5-0.8 of the melting temperature, T), contact pressure and fast strain rates result in transient microstructures and grain size reduction by continuous dynamic recrystallization (CDRX) within the bonding zone. Bonding occurs by local grain boundary migration, which allows diffusion and atom interlocking across the contact between two clean surfaces. Textures weaken with increasing contact pressure due to increased strain hardening and different grain rotation rates. High contact pressures enhance dynamic recovery and CDRX. Deformation around the fibre is intense within 50 μm and extends to 450 μm from it. © 2009 Acta Materialia Inc.

Hot deformation characteristics of a nitride strengthened martensitic heat resistant steel

Constitutive equations including an Arrhenius term have been applied to analyze the hot deformation behavior of a nitride-strengthened (NS) martensitic heat resistant steel in temperature range of 900–1200 °C and strain rate range of 0.001–10 /s. On the basis of analysis of the deformation data, the stress–strain curves up to the peak were divided into four regions, in sequence, representing four processes, namely hardening, dynamic recovery (DRV), dynamic strain induced transformation (DSIT), and dynamic recrystallization (DRX), according to the inflection points in ∂θ/∂σ∂θ/∂σ and ∂(∂θ/∂σ)/∂σ∂(∂θ/∂σ)/∂σ curves. Some of the inflection points have their own meanings. For examples, the minimum of ∂θ/∂σ∂θ/∂σ locates the start of DRV and the maximum of it indicates the start of DRX. The results also showed that the critical strain of DRX was sensitive to ln(Z) below 40, while the critical stress of DRX was sensitive to it above 40. The final microstructures under different deformation conditions were analyzed in terms of softening processes including DRV, DRX, metadynamic crystallization (MDRX) and DSIT.

Analysis of deformation behavior and workability of advanced 9Cr-Nb-V ferritic heat resistant steels

Hot compression tests were carried out on 9Cr–Nb–V heat resistant steels in the temperature range of 600–1200 °C and the strain rate range of 10−2–100 s−1 to study their deformation characteristics. The full recrystallization temperature and the carbon-free bainite phase transformation temperature were determined by the slope-change points in the curve of mean flow stress versus the inverse of temperature. The parameters of the constitutive equation for the experimental steels were calculated, including the stress exponent and the activation energy. The lower carbon content in steel would increase the fraction of precipitates by increasing the volume of dynamic strain-induced (DSIT) ferrite during deformation. The ln(εc) versus ln(Z) and the ln(σc) versus ln(Z) plots for both steels have similar trends. The efficiency of power dissipation maps with instability maps merged together show excellent workability from the strain of 0.05 to 0.6. The microstructure of the experimental steels was fully recrystallized upon deformation at low Z value owing to the dynamic recrystallization (DRX), and exhibited a necklace structure under the condition of 1050 °C/0.1 s−1 due to the suppression of the secondary flow of DRX. However, there were barely any DRX grains but elongated pancake grains under the condition of 1000 °C/1 s−1 because of the suppression of the metadynamic recrystallization (MDRX).

Constitutive modeling, microstructure evolution, and processing map for a nitride-strengthened heat-resistant steel

A constitutive equation was established to describe the deformation behavior of a nitride-strengthened (NS) steel through isothermal compression simulation test. All the parameters in the constitutive equation including the constant and the activation energy were precisely calculated for the NS steel. The result also showed that from the stress-strain curves, there existed two different linear relationships between critical stress and critical strain in the NS steel due to the augmentation of auxiliary softening effect of the dynamic strain-induced transformation. In the calculation of processing maps, with the change of Zener-Hollomon value, three domains of different levels of workability were found, namely excellent workability region with equiaxed-grain microstructure, good workability region with “stripe” microstructure, and the poor workability region with martensitic-ferritic blend microstructure. With the increase of strain, the poor workability region first expanded, then shrank to barely existing, but appeared again at the strain of 0.6.

Comparative Study of Different Methods for the Prediction of Drug− Polymer Solubility

In this study, a comparison of different methods to predict drug−polymer solubility was carried out on binary systems consisting of five model drugs (paracetamol, chloramphenicol, celecoxib, indomethacin, and felodipine) and polyvinylpyrrolidone/vinyl acetate copolymers (PVP/VA) of different monomer weight ratios. The drug−polymer solubility at 25 °C was predicted using the Flory−Huggins model, from data obtained at elevated temperature using thermal analysis methods based on the recrystallization of a supersaturated amorphous solid dispersion and two variations of the melting point depression method. These predictions were compared with the solubility in the low molecular weight liquid analogues of the PVP/VA copolymer (N-vinylpyrrolidone and vinyl acetate). The predicted solubilities at 25 °C varied considerably depending on the method used. However, the three thermal analysis methods ranked the predicted solubilities in the same order, except for the felodipine−PVP system. Furthermore, the magnitude of the predicted solubilities from the recrystallization method and melting point depression method correlated well with the estimates based on the solubility in the liquid analogues, which suggests that this method can be used as an initial screening tool if a liquid analogue is available. The learnings of this important comparative study provided general guidance for the selection of the most suitable method(s) for the screening of drug−polymer solubility.

Synthesis and functionalization of hydroxyapatite nanoparticles

Graças aos desenvolvimentos na área da síntese de nanomaterais e às potentes técnicas de caracterização à nanoescala conseguimos hoje visualizar uma nanopartícula (NP) como um dispositivo de elevado potencial terapêutico. A melhoria da sua efectividade terapêutica requer no entanto o aprofundamento e sistematização de conhecimentos, ainda muito incipientes, sobre toxicidade, selectividade, efeitos colaterais e sua dependência das próprias características físico-químicas da NP em análise. O presente trabalho, elegendo como alvo de estudo uma substância considerada biocompatível e não tóxica, a hidroxiapatite (Hap), pretende dar um contributo para esta área do conhecimento. Definiram-se como metas orientadoras deste trabalho (i) estudar a síntese de nanoparticulas de Hap (Hap NP), e a modificação das características físico-químicas e morfológicas das mesmas através da manipulação das condições de síntese; (ii) estudar a funcionalização das Hap NP com nanoestruturas de ouro e com ácido fólico, para lhes conferir capacidades acrescidas de imagiologia e terapêuticas, particularmente interessantes em aplicações como o tratamento do cancro (iii) estudar a resposta celular a materiais nanométricos, com propriedades físico-químicas diversificadas. No que se refere à síntese de Hap NP, comparam-se dois métodos de síntese química distintos, a precipitação química a temperatura fisiológica (WCS) e a síntese hidrotérmica (HS), em meios aditivados com ião citrato. A síntese WCS originou partículas de tamanho nanométrico, com uma morfologia de agulha, pouco cristalinas e elevada área superficial especifica. A síntese HS à temperatura de 180ºC permitiu obter partículas de dimensões também nanométricas mas com área específica inferior, com morfologia de bastonete prismático com secção recta hexagonal e elevada cristalinidade. Com o objectivo de aprofundar o papel de algumas variáveis experimentais na definição das características finais das partículas de hidroxiapatite, designadamente o papel do ião citrato (Cit), variou-se a razão molar [Cit/Ca] da solução reagente e o tempo de síntese. Demonstrou-se que o ião citrato e outras espécies químicas resultantes da sua decomposição nas condições térmicas (180ºC) de síntese tem um papel preponderante na velocidade de nucleação e de crescimento dessas mesmas partículas e por conseguinte nas características físico-químicas das mesmas. Elevadas razões [Cit/Ca] originam partículas de dimensão micrométrica cuja morfologia é discutida no contexto do crescimento com agregação. Com o objectivo de avaliar a citotoxicidade in vitro das nanopartículas sintetizadas procedeu-se à esterilização das mesmas. O método de esterilização escolhido foi a autoclavagem a 121º C. Avaliou-se o impacto do processo de esterilização nas características das partículas, verificando-se contrariamente às partículas WCS, que as partículas HS não sofrem alterações significativas de morfologia, o que se coaduna com as condições de síntese das mesmas, que são mais severas do que as de esterilização. As partículas WCS sofrem processos de dissolução e recristalização que se reflectem em alterações significativas de morfologia. Este estudo demonstrou que a etapa de esterilização de nanopartículas para aplicações biomédicas, por autoclavagem, pode alterar substancialmente as propriedades das mesmas, sendo pois criticamente importante caracterizar os materiais após esterilização. Os estudos citotoxicológicos para dois tipos de partículas esterilizadas (HSster e WCSster) revelaram que ambas apresentam baixa toxicidade e possuem potencial para a modelação do comportamento de células osteoblásticas. Tendo em vista a funcionalização da superfície das Hap NP para multifunções de diagnóstico e terapia exploraram-se condições experimentais que viabilizassem o acoplamento de nanopartículas de ouro à superfície das nanopartículas de Hidroxiapatite (Hap-AuNP). Tirando partido da presença de grupos carboxílicos adsorvidos na superfície das nanopartículas de Hap foi possível precipitar partículas nanométricas de ouro (1,5 a 2,5 nm) na superfície das mesmas adaptando o método descrito por Turkevich. No presente trabalho as nanopartículas de Hap funcionaram assim como um template redutor do ouro iónico de solução, propiciando localmente, na superfície das próprias nanopartículas de Hap, a sua redução a ouro metálico. A nucleação do ouro é assim contextualizada pelo papel redutor das espécies químicas adsorvidas, designadamente os grupos carboxílicos derivados de grupos citratos que presidiram à síntese das próprias nanopartículas de Hap. Estudou-se também a funcionalização das Hap NP com ácido fólico (FA), uma molécula biologicamente interessante por ser de fácil reconhecimento pelos receptores existentes em células cancerígenas. Os resultados confirmaram a ligação do ácido fólico à superfície das diferentes partículas produzidas HS e Hap-AuNPs. Graças às propriedades ópticas do ouro nanométrico (efeito plasmão) avaliadas por espectroscopia vis-UV e às potencialidades de hipertermia local por conversão fototérmica, as nanoestruturas Hap-AuNPs produzidas apresentam-se com elevado interesse enquanto nanodispositivos capazes de integrar funções de quimio e terapia térmica do cancro e imagiologia. O estudo da resposta celular aos diversos materiais sintetizados no presente trabalho foi alvo de análise na tentativa de se caracterizar a toxicidade dos mesmos bem como avaliar o seu desempenho em aplicações terapêuticas. Demonstrou-se que as Hap NP não afectam a proliferação das células para concentrações até 500 g/ml, observando-se um aumento na expressão genética da BMP-2 e da fosfatase alcalina. Verificou-se também que as Hap NP são susceptíveis de internalização por células osteoblásticas MG63, apresentando uma velocidade de dissolução intracelular relativamente reduzida. A resposta celular às Hap-AuNP confirmou a não citotoxicidade destas partículas e revelou que a presença do ouro na superfície das Hap NP aumenta a taxa proliferação celular, bem como a expressão de parâmetros osteogénicos. No seu conjunto os resultados sugerem que os vários tipos de partículas sintetizadas no presente estudo apresentam também comportamentos interessantes para aplicações em engenharia de tecido ósseo.

Microfacies analysis of the lower paleocene beda formation in Western Concession 59 and Block 59F, Sirte Basin, Libya /

The rock sequence of the Tertiary Beda Formation of S. W. concession 59 and 59F block in Sirte Basin of Libya has been subdivided into twelve platformal carbonate microfacies. These microfacies are dominated by muddy carbonates, such as skeletal mudstones, wackestones, and packstones with dolomites and anhydrite. Rock textures, faunal assemblages and sedimentary structures suggest shallow, clear, warm waters and low to moderate energy conditions within the depositional shelf environment. The Beda Formation represents a shallowing-upward sequence typical of lagoonal and tidal flat environments marked at the top by sabkha and brackish-water sediments. Microfossils include benthonic foraminifera, such as miliolids, Nummulites, - oerculina and other smaller benthonics, in addition to dasycladacean algae, ostracods, molluscs, echinoderms, bryozoans and charophytes. Fecal pellets and pelloids, along with the biotic allochems, contributed greatly to the composition of the various microfacies. Dolomite, where present, is finely crystalline and an early replacement product. Anhydrite occurs as nodular, chickenwire and massive textures indicating supratidal sabkha deposition. Compaction, micr it i zat ion , dolomit izat ion , recrystallization, cementation, and dissolution resulted in alteration and obliteration of primary sedimentary structures of the Beda Formation microfacies. The study area is located in the Gerad Trough which developed as a NE-SW trending extensional graben. The Gerad trough was characterized by deep-shallow water conditions throughout the deposition of the Beda Formation sediments. The study area is marked by several horsts and grabens; as a result of extent ional tectonism. The area was tectonically active throughout the Tertiary period. Primary porosity is intergranular and intragranular, and secondary processes are characterized by dissolution, intercrystalline, fracture and fenestral features. Diagenesis, through solution leaching and dolomitization, contributed greatly to porosity development. Reservoir traps of the Beda Formation are characterized by normal fault blocks and the general reservoir characteristics/properties appear to be facies controlled.

Petrography, geochemistry and structure of the Timmins area, Ontario

Regional structural analysis of the Timmins area indicates four major periods of tectonic deformation. The DI deformation is characterized by a series of isoclinal FI folds which are outlined in the study area by bedding, pillow tops and variolitic flows. The D2 deformation developed the Porcupine Syncline and refolded the Fl folds about a NE. axis. A pervasive S2 foliation developed during low grade (greenschist) regional metamorphism associated with the D2 deformation. The S2 foliation developed south of the Destor-Porcupine Break. The third phase of tectonic D3 deformation is recognized by the development of a S3 sub-horizontal crenulation cleavage which developed on the plane of the S2 foliation. No meso scopic folds are associated with this deformation. The 8 3 crenulation cleavage is observed south of the Destor-Porcupine Break. The D4 tectonic deformation is recorded as a subvertical S4 crenulation cleavage which developed on the plane of the S2 foliation and also offsets the S3 crenulation cleavage. Macroscopic F4 folds have refolded the F2 axial plane. No metamorphic recrystallization is associated with this deformation. The S4 crenulation cleavage is observed south of the Destor-Porcupine Break. Petrographic evidence indicates that the Timmins area has been subjected to pervasive regional low grade (greenschist) metamorphism which has recrystallized the original mineralogy. South of the study are~ the Donut Lake ultramafic lavas have been subjected to contact medium grade (amphibolite facies) metamorphism associated with the intrusion of the Peterlong Lake Complex. The Archean volcanic rocks of the Timmins area have been subdivided into komatiitic, tholeiitic and calcalkaline suites based on Zr, Ti0 2 and Ni. The three elements were used because of their r e lative immobility during subsequent metamorphic events. Geochemical observations in the Timmins area indicates that the composition of the Goose Lake and Donut Lake Formations are a series of peridotitic, pyroxenitic and basaltic komatiites. The Lower Schumacher Formation is a sequence of basaltic komatiites while the upper part of the Lower Schumacher Formation is an intercalated sequence of basaltic komatiites and low Ti0 2 tholeiites. The variolitic flows are felsic tholeiites in composition and geochemical evidenc e sugg ests that they developed as a n immiscible splitting of a tholeiitic magma. The Upper Schumacher Formation is a sequence of tholeiitic rocks dis p laying a mild iron enrichment. The Krist and Boomerang Formations are the felsic calc-alkaline rocks of the study area which are characteristically pyroclastic. The Redstone Fo rmation is dominantly a calc-alkali ne sequence of volcani c rocks whose minor mafic end me mbers exposed in 1t.he study hav e basaltic komatiitic compositions. Geochemical evidence sugges ts that the Keewatin-type se dimentary rocks have a composition similar to a quartz diorite or a granodiorite. Fi e l d obs ervations and petrographic evidence suggests that they were derived fr om a distal source and now repr esent i n part a turbidite sequence. The Timiskaming-type sedimentary rocks approach the c omp osi t ion of the felsic calc-alkaline rocks of the study area . The basal conglomerate in the study are a sugge s ts that th e uni t was derived fr om a proximal source. Petrographic and ge ochemical evidence suggests that the peridotitic and pyroxenitic komatiites originated as a 35-55% partial melt within the mantle, in excess of 100 Km. depth. The melt ros e as a diapir with the subsequent effusion of the ultramafic lavas, The basaltic komatiites and tholeiitic rocks originated in the mantle from lesser degrees of partial melting and fractionated in low pressure chambers. Geochemical evidence suggests a "genetic link" between the basaltic komatiites and tholeiites, The calc-alkaline rocks developed as a result of the increa.se In PO in the magma chamber. The felsic calcalkaline rocks are a late stage effusion possibly the last major volcanic eruptions in the area.

Electrospinning and characterization of self-assembled inclusion complexies

L’électrofilage est une technique permettant de fabriquer des fibres polymériques dont le diamètre varie entre quelques nanomètres et quelques microns. Ces fibres ont donc un rapport surface/volume très élevé. Les fibres électrofilées pourraient trouver des applications dans le relargage de médicaments et le génie tissulaire, comme membranes et capteurs chimiques, ou dans les nanocomposites et dispositifs électroniques. L’électrofilage était initialement utilisé pour préparer des toiles de fibres désordonnées, mais il est maintenant possible d’aligner les fibres par l’usage de collecteurs spéciaux. Cependant, il est important de contrôler non seulement l’alignement macroscopique des fibres mais aussi leur orientation au niveau moléculaire puisque l’orientation influence les propriétés mécaniques, optiques et électriques des polymères. Les complexes moléculaires apparaissent comme une cible de choix pour produire des nanofibres fortement orientées. Dans les complexes d’inclusion d’urée, les chaînes polymères sont empilées dans des canaux unidimensionnels construits à partir d’un réseau tridimensionnel de molécules d’urée liées par des ponts hydrogène. Ainsi, les chaînes polymère sonts très allongées à l’échelle moléculaire. Des nanofibres du complexe PEO-urée ont été préparées pour la première fois par électrofilage de suspensions et de solutions. Tel qu’attendu, une orientation moléculaire inhabituellement élevée a été observée dans ces fibres. De tels complexes orientés pourraient être utilisés à la fois dans des études fondamentales et dans la préparation de matériaux hiérarchiquement structurés. La méthode d’électrofilage peut parfois aussi être utilisée pour préparer des matériaux polymériques métastables qui ne peuvent pas être préparés par des méthodes conventionnelles. Ici, l’électrofilage a été utilisé pour préparer des fibres des complexes stables (α) et "métastables" (β) entre le PEO et l’urée. La caractérisation du complexe β, qui était mal connu, révèle un rapport PEO:urée de 12:8 appartenant au système orthorhombique avec a = 1.907 nm, b = 0.862 nm et c = 0.773 nm. Les chaînes de PEO sont orientées selon l’axe de la fibre. Leur conformation est significativement affectée par les ponts hydrogène. Une structure en couches a été suggérée pour la forme β, plutôt que la structure conventionnelle en canaux adoptée par la forme α. Nos résultats indiquent que le complexe β est thermodynamiquement stable avant sa fonte et peut se transformer en forme α et en PEO liquide par un processus de fonte et recristallisation à 89 ºC. Ceci va dans le sens contraire aux observations faites avec le complexe β obtenu par trempe du complexe α fondu. En effet, le complexe β ainsi obtenu est métastable et contient des cristaux d’urée. Il peut subir une transition de phases cinétique solide-solide pour produire du complexe α dans une vaste gamme de températures. Cette transition est induite par un changement de conformation du PEO et par la formation de ponts hydrogène intermoléculaires entre l’urée et le PEO. Le diagramme de phases du système PEO-urée a été tracé sur toute la gamme de compositions, ce qui a permis d’interpréter la formation de plusieurs mélanges qui ne sont pas à l’équilibre mais qui sont été observés expérimentalement. La structure et le diagramme de phases du complexe PEO-thiourée, qui est aussi un complexe très mal connu, ont été étudiés en détail. Un rapport molaire PEO :thiourée de 3:2 a été déduit pour le complexe, et une cellule monoclinique avec a = 0.915 nm, b = 1.888 nm, c = 0.825 nm et β = 92.35º a été déterminée. Comme pour le complexe PEO-urée de forme β, une structure en couches a été suggérée pour le complexe PEO-thiourée, dans laquelle les molécules de thiourée seraient disposées en rubans intercalés entre deux couches de PEO. Cette structure en couches pourrait expliquer la température de fusion beaucoup plus faible des complexes PEO-thiourée (110 ºC) et PEO-urée de forme β (89 ºC) en comparaison aux structures en canaux du complexe PEO-urée de forme α (143 ºC).

L’étude de l’InP et du GaP suite à l’implantation ionique de Mn et à un recuit thermique

Cette thèse est dédiée à l’étude des matériaux InMnP et GaMnP fabriqués par implantation ionique et recuit thermique. Plus précisément nous avons investigué la possibilité de former par implantation ionique des matériaux homogènes (alliages) de InMnP et GaMnP contenant de 1 à 5 % atomiques de Mn qui seraient en état ferromagnétique, pour des possibles applications dans la spintronique. Dans un premier chapitre introductif nous donnons les motivations de cette recherche et faisons une revue de la littérature sur ce sujet. Le deuxième chapitre décrit les principes de l’implantation ionique, qui est la technique utilisée pour la fabrication des échantillons. Les effets de l’énergie, fluence et direction du faisceau ionique sur le profil d’implantation et la formation des dommages seront mis en évidence. Aussi dans ce chapitre nous allons trouver des informations sur les substrats utilisés pour l’implantation. Les techniques expérimentales utilisées pour la caractérisation structurale, chimique et magnétique des échantillons, ainsi que leurs limitations sont présentées dans le troisième chapitre. Quelques principes théoriques du magnétisme nécessaires pour la compréhension des mesures magnétiques se retrouvent dans le chapitre 4. Le cinquième chapitre est dédié à l’étude de la morphologie et des propriétés magnétiques des substrats utilisés pour implantation et le sixième chapitre, à l’étude des échantillons implantés au Mn sans avoir subi un recuit thermique. Notamment nous allons voir dans ce chapitre que l’implantation de Mn à plus que 1016 ions/cm2 amorphise la partie implantée du matériau et le Mn implanté se dispose en profondeur sur un profil gaussien. De point de vue magnétique les atomes implantés se trouvent dans un état paramagnétique entre 5 et 300 K ayant le spin 5/2. Dans le chapitre 7 nous présentons les propriétés des échantillons recuits à basses températures. Nous allons voir que dans ces échantillons la couche implantée est polycristalline et les atomes de Mn sont toujours dans un état paramagnétique. Dans les chapitres 8 et 9, qui sont les plus volumineux, nous présentons les résultats des mesures sur les échantillons recuits à hautes températures : il s’agit d’InP et du GaP implantés au Mn, dans le chapitre 8 et d’InP co-implanté au Mn et au P, dans le chapitre 9. D’abord, dans le chapitre 8 nous allons voir que le recuit à hautes températures mène à une recristallisation épitaxiale du InMnP et du GaMnP; aussi la majorité des atomes de Mn se déplacent vers la surface à cause d’un effet de ségrégation. Dans les régions de la surface, concentrés en Mn, les mesures XRD et TEM identifient la formation de MnP et d’In cristallin. Les mesures magnétiques identifient aussi la présence de MnP ferromagnétique. De plus dans ces mesures on trouve qu’environ 60 % du Mn implanté est en état paramagnétique avec la valeur du spin réduite par rapport à celle trouvée dans les échantillons non-recuits. Dans les échantillons InP co-implantés au Mn et au P la recristallisation est seulement partielle mais l’effet de ségrégation du Mn à la surface est beaucoup réduit. Dans ce cas plus que 50 % du Mn forme des particules MnP et le restant est en état paramagnétique au spin 5/2, dilué dans la matrice de l’InP. Finalement dans le dernier chapitre, 10, nous présentons les conclusions principales auxquels nous sommes arrivés et discutons les résultats et leurs implications.

Défauts et diffusion dans le silicium amorphe

Nous avons observé une augmentation ‘’transient’’du taux de cristallisation interfacique de l’a-Si lorsqu’on réimplante du Si à proximité de l’interface amorphe/cristal. Après amorphisation et traitement thermique à 650°C pendant 5s de la couche a-Si crée par implantation ionique, une partie a été réimplantée. Les défauts produits par auto-réimplantation à 0.7MeV se trouvent à (302±9) nm de l’interface initiale. Cela nous a permis d’étudier d’avantage la variation initiale de la vitesse SPE (Épitaxie en phase solide). Avec des recuit identiques de 4h à 500°C, nous avons déterminé les positions successives des interfaces et en déduit les taux de cristallisation SPE. La cristallisation débute à l’interface et continue graduellement vers la surface. Après le premier recuit, (252±11) nm s’est recristallisé dans la zone réimplantée soit un avancement SPE de 1.26x10^18at./cm2. Cette valeur est environ 1.50 fois plus importante que celle dans l’état relaxé. Nous suggérons que la présence de défauts à proximité de l’interface a stimulé la vitesse initiale. Avec le nombre de recuit, l’écart entre les vitesses diminue, les deux régions se cristallisent presque à la même vitesse. Les mesures Raman prises avant le SPE et après chaque recuit ont permis de quantifier l’état de relaxation de l’a-Si et le transfert de l’état dé-relaxé à relaxé.

4,5-Dihydro-1,3-dioxepine als chirale Bausteine in der enantioselektiven organischen Synthese

Durch asymmetrische Doppelbindungsisomerisierung mittels Me-DuPHOS-modifizierter Dihalogen-Nickel-Komplexe als Katalysatorvorstufen lassen sich aus 2-Alkyl-4,7-dihydro-1,3-dioxepinen hochenantiomerenreine 2-Alkyl-4,5-dihydro-1,3-dioxepine erhalten. Ein Ziel dieser Arbeit war es, die bisher noch unbekannte Absolutkonfiguration dieses Verbindungstyps zu bestimmen und darüber hinaus ihre Einsatzfähigkeit in der enantioselektiven organischen Synthese zu untersuchen. Zu diesem Zweck wurden enantiomerenangereichertes 2-Isopropyl- und 2-tert-Butyl-4,5-dihydro-1,3-dioxepin mit m-Chlorperbenzoesäure epoxidiert. Dabei bildeten sich die entsprechenden 3-Chlorbenzoesäure-(2-alkyl-5-hydroxy-1,3-dioxepan-4yl)-ester in hohen Ausbeuten und Diastereoselektivitäten. Von den vier zu erwartenden Diastereomeren wurden jeweils nur zwei mit einer Selektivität von mehr als 95:5 gebildet. Im Fall des 3-Chlorbenzoesäure-(2-isopropyl-5-hydroxy-1,3-dioxepan-4yl)-esters konnte das Haupt-diastereomer kristallin erhalten werden. Durch röntgenspektroskopische Untersuchung war es möglich, die Relativ-Konfiguration dieser Verbindung zu bestimmen. Die Ester lassen sich unter Ringverengung in 2-Alkyl-1,3-dioxan-4-carbaldehyde umlagern. Ausgehend von diesen Carbaldehyden stehen zwei Synthesewege zur Verfügung, welche zu Verbindungen führen deren Absolutkonfiguration bereits bekannt ist. So erhält man durch Reduktion 2-Alkyl-1,3-dioxan-4-yl-methanole, welche sich in 1,2,4-Butantriol überführen lassen. Oxidation ergibt die 2-Alkyl-1,3-dioxan-4-carbonsäuren, aus denen 3-Hydroxytetrahydrofuran-2-on gewonnen werden kann. Messung des Drehwertes dieser beiden literaturbekannten Verbindungen liefert nicht nur Information über deren Enantiomerenreinheit sondern ebenfalls über die Konfiguration ihres Stereozentrums. In Kombination mit der Relativ-Konfiguration des Esters ist somit ein Rückschluss auf die Absolutkonfiguration der eingesetzten 4,5-Dihydro-1,3-dioxepine möglich. Die auf den beschriebenen Wegen gewonnenen Substanzen finden Anwendung in der stereoselektiven organischen Synthese. Löst man die Chlorbenzoesäureester in Dichlormethan und behandelt sie mit wässriger Salzsäure, so entstehen die bicyclischen 2-Alkyltetrahydrofuro[2,3-d][1,3]dioxole. Auch bei diesen Verbindungen konnten hohe Enantio- und Diastereoselektivitäten erzielt werden. Der intermolekular verlaufende Reaktionsmechanismus der Bicyclus-Bildung, welcher unter Abspaltung eines den Alkylrest tragenden Aldehyds und dessen Neuanlagerung unter Ausbildung eines Acetals verläuft, konnte in dieser Arbeit durch ein Kreuzungsexperiment bestätigt werden. Umacetalisierung der Bicyclen liefert 2-Methoxytetrahydrofuran-3-ol, aus dem durch Acetalspaltung Tetrahydrofuran-2,3-diol erhalten wird, das die Halbacetalform der entsprechenden Desoxytetrose darstellt, die auf diese Weise in einer de novo-Synthese hergestellt werden kann.

Fliesslochformen und Gewindefurchen in dünne Bleche und Rohre aus Kupfer und Kupferlegierungen

This thesis in Thermal Flow Drilling and Flowtap in thin metal sheet and pipes of copper and copper alloys had as objectives to know the comportment of copper and copper alloys sheet metal during the Thermal Flow Drill processes with normal tools, to know the best Speed and Feed machine data for the best bushing quality, to known the best Speed for Form Tapping processes and to know the best bush long in pure copper pipes for water solar interchange equipment. Thermal Flow Drilling (TFD) and Form Tapping (FT) is one of the research lines of the Institute of Production and Logistics (IPL) at University of Kassel. At December 1995, a work meeting of IPL, Santa Catarina University, Brazil, Buenos Aires University, Argentine, Tarapacá University (UTA), Chile members and the CEO of Flowdrill B.V. was held in Brazil. The group decided that the Manufacturing Laboratory (ML) of UTA would work with pure copper and brass alloys sheet metal and pure copper pipes in order to develop a water interchange solar heater. The Flowdrill BV Company sent tools to Tarapacá University in 1996. In 1999 IPL and the ML carried out an ALECHILE research project promoted by the DAAD and CONICyT in copper sheet metal and copper pipes and sheet metal a-brass alloys. The normal tools are lobed, conical tungsten carbide tool. When rotated at high speed and pressed with high axial force into sheet metal or thin walled tube generated heat softens the metal and allows the drill to feed forward produce a hole and simultaneously form a bushing from the displacement material. In the market exist many features but in this thesis is used short and longs normal tools of TFD. For reach the objectives it was takes as references four qualities of the frayed end bushing, where the best one is the quality class I. It was used pure copper and a-brass alloys sheet metals, with different thickness. It was used different TFD drills diameter for four thread type, from M-5 to M10. Similar to the Aluminium sheet metals studies it was used the predrilling processes with HSS drills around 30% of the TFD diameter (1,5 – 3,0 mm D). In the next step is used only 2,0 mm thick metal sheet, and 9,2 mm TFD diameter for M-10 thread. For the case of pure commercial copper pipes is used for ¾” inch diameter and 12, 8 mm (3/8”) TFD drill for holes for 3/8” pipes and different normal HSS drills for predrilling processes. The chemical sheet metal characteristics were takes as reference for the material behaviour. The Chilean pure copper have 99,35% of Cu and 0,163% of Zinc and the Chilean a-brass alloys have 75,6% of Cu and 24,0% of Zinc. It is used two German a-brass alloys; Nº1 have 61,6% of Cu, 36,03 % of Zinc and 2,2% of Pb and the German a-brass alloys Nº2 have 63,1% of Cu, 36,7% of Zinc and 0% of Pb. The equipments used were a HAAS CNC milling machine centre, a Kistler dynamometer, PC Pentium II, Acquisition card, TESTPOINT and XAct software, 3D measurement machine, micro hardness, universal test machine, and metallographic microscope. During the test is obtained the feed force and momentum curves that shows the material behaviour with TFD processes. In general it is take three phases. It was possible obtain the best machining data for the different sheet of copper and a-brass alloys thick of Chilean materials and bush quality class I. In the case of a-brass alloys, the chemical components and the TFD processes temperature have big influence. The temperature reach to 400º Celsius during the TFD processes and the a-brass alloys have some percents of Zinc the bush quality is class I. But when the a-brass alloys have some percents of Lead who have 200º C melting point is not possible to obtain a bush, because the Lead gasify and the metallographic net broke. During the TFD processes the recrystallization structures occur around the Copper and a-brass alloy bush, who gives more hardness in these zones. When the threads were produce with Form Tapping processes with Flowtap tools, this hardness amount gives a high limit load of the thread when hey are tested in a special support that was developed for it. For eliminated the predrilling processes with normal HSS drills it was developed a compound tool. With this new tool it was possible obtain the best machining data for quality class I bush. For the copper pipes it is made bush without predrilling and the quality class IV was obtained. When it is was used predrilling processes, quality classes I bush were obtained. Then with different HSS drill diameter were obtained different long bush, where were soldering with four types soldering materials between pipes with 3/8” in a big one as ¾”. Those soldering unions were tested by traction test and all the 3/8” pipes broken, and the soldering zone doesn’t have any problem. Finally were developed different solar water interchange heaters and tested. As conclusions, the present Thesis shows that the Thermal Flow Drilling in thinner metal sheets of cooper and cooper alloys needs a predrilling process for frayed end quality class I bushings, similar to thinner sheets of aluminium bushes. The compound tool developed could obtain quality class I bushings and excludes predrilling processes. The bush recrystalization, product of the friction between the tool and the material, the hardness grows and it is advantageous for the Form Tapping. The methodology developed for commercial copper pipes permits to built water solar interchange heaters.

(Diethyleneglycol dimethyl ether)tris(1,1,1,5,5,5-hexafluoropentane-2,4-dionato)praseodymium(III)

The title compound, [Pr(C5HF6O2)(3)(C6H14O3)] or [Pr(hfpd)(3)(2g)], was prepared by the reaction of PrCl3.7H(2)O and hfpd-H (1,1,1,5,5,5-hexafiuoropentane-2,4-dione) in the presence of aqueous ammonia and recrystallization of the product from n-hexane in the presence of diglyme (2g). The metal atom is nine-coordinate, bonded to three bidentate beta-diketonato ligands and the polyether molecule.