System studies of the superconducting fault current limiter in electrical distribution grids

A superconducting fault current limiter (SFCL) in series with a downstream circuit breaker could provide a viable solution to controlling fault current levels in electrical distribution networks. In order to integrate the SFCL into power grids, we need a way to conveniently predict the performance of the SFCL in a given scenario. In this paper, short circuit analysis based on the electromagnetic transient program was used to investigate the operational behavior of the SFCL installed in an electrical distribution grid. System studies show that the SFCL can not only limit the fault current to an acceptable value, but also mitigate the voltage sag. The transient recovery voltage (TRV) could be remarkably damped and improved by the presence of the SFCL after the circuit breaker is opened to clear the fault. © 2007 British Crown Copyright.

A literature and practice review to develop sustainable business model archetypes

Eco-innovations, eco-efficiency and corporate social responsibility practices define much of the current industrial sustainability agenda. While important, they are insufficient in themselves to deliver the holistic changes necessary to achieve long-term social and environmental sustainability. How can we encourage corporate innovation that significantly changes the way companies operate to ensure greater sustainability? Sustainable business models (SBM) incorporate a triple bottom line approach and consider a wide range of stakeholder interests, including environment and society. They are important in driving and implementing corporate innovation for sustainability, can help embed sustainability into business purpose and processes, and serve as a key driver of competitive advantage. Many innovative approaches may contribute to delivering sustainability through business models, but have not been collated under a unifying theme of business model innovation. The literature and business practice review has identified a wide range of examples of mechanisms and solutions that can contribute to business model innovation for sustainability. The examples were collated and analysed to identify defining patterns and attributes that might facilitate categorisation. Sustainable business model archetypes are introduced to describe groupings of mechanisms and solutions that may contribute to building up the business model for sustainability. The aim of these archetypes is to develop a common language that can be used to accelerate the development of sustainable business models in research and practice. The archetypes are: Maximise material and energy efficiency; Create value from 'waste'; Substitute with renewables and natural processes; Deliver functionality rather than ownership; Adopt a stewardship role; Encourage sufficiency; Re-purpose the business for society/environment; and Develop scale-up solutions. © 2014 The Authors. Published by Elsevier Ltd. All rights reserved.

Quantum efficiency and temperature coefficients of GaInP/GaAs dual-junction solar cell

GaInP/GaAs dual-junction solar cell with a conversion efficiency of 25.2% has been fabricated using metalorganic chemical vapor deposition (MOCVD) technique. Quantum efficiencies of the solar cell were measured within a temperature range from 25 to 160A degrees C. The results indicate that the quantum efficiencies of the subcells increase slightly with the increasing temperature. And red-shift phenomena of absorption limit for all subcells are observed by increasing the cell's work temperature, which are consistent with the viewpoint of energy gap narrowing effect. The short-circuit current density temperature coefficients dJ (sc)/dT of GaInP subcell and GaAs subcell are determined to be 8.9 and 7.4 mu A/cm(2)/A degrees C from the quantum efficiency data, respectively. And the open-circuit cell voltage temperature coefficients dV (oc)/dT calculated based on a theoretical equation are -2.4 mV/A degrees C and -2.1 mV/A degrees C for GaInP subcell and GaAs subcell.

Temperature dependent spectral response characteristic of III-V compound tandem cell

The GaInP/GaAs/Ge triple-junction tandem cells with a conversion efficiency of 27.1% were fabricated using metalorganic chemical vapor deposition (MOCVD) technique. Temperature dependence of the spectral response measurements of the GaInP/GaAs/Ge tandem cell was performed by a quantum efficiency system at temperatures ranging from 25A degrees C to 160A degrees C. The red-shift phenomena of the absorption limit for all subcells were observed with increasing temperature, which is dued to the energy gap narrowing with temperature. The short-circuit current densities (J (sc)) of GaInP, GaAs and Ge subcells at room temperature calculated based on the spectral response data were 12.9, 13.7 and 17 mA/cm(2), respectively. The temperature coefficient of J (sc) for the tandem cell was determined to be 8.9 mu A/(cm(2) center dot A degrees C), and the corresponding temperature coefficient of the open-circuit voltage deduced from the series-connected model was -6.27 mV/A degrees C.

Influence of penetrating V-pits on leakage current of GaN based p-i-n UV detector

The leakage mechanism of GaN-based p-i-n (p-AlGaN/i-GaN/n-GaN) UV detector has been investigated. With the same dislocation density, devices made from material with higher density of V-pits on surface produce larger leakage current. SEM images show that some V-pits penetrate into i-GaN layer, sometimes even the n-GaN layer. If p-ohmic contact metal (Ni/Au) deposits in the V-pits, Schottky contact would be formed at the interface of metal and i-GaN, or form ohmic contact at the interface of metal and n-GaN. The existence of parallel Schottky junction and ohmic contact resistance enhances the leakage current greatly.

Computer simulation of a-Si : H/mu c-Si : H diphasic silicon solar cells

Based on our experimental research on diphasic silicon films, the parameters such as absorption coefficient, mobility lifetime product and bandgap were estimated by means of effective-medium theory. And then computer simulation of a-Si: H/mu c-Si: H diphasic thin film solar cells was performed. It was shown that the more crystalline fraction in the diphasic silicon films, the higher short circuit density, the lower open-circuit voltage and the lower efficiency. From the spectral response, we can see that the response in long wave region was improved significantly with increasing crystalline fraction in the silicon films. Taking Lambertian back refraction into account, the diphasic silicon films with 40%-50% crystalline fraction was considered to be the best intrinsic layer for the bottom solar cell in micromorph tandem.

A new technique for boosting efficiency of silicon solar cells

A new type of photovoltaic system with higher generation power density has been studied in detail. The feature of the system is a V-shaped module (VSM) with two tilted monocrystalline solar cells. Compared to solar cells in a flat orientation, the VSM enhances external quantum efficiency and leads to an increase of 31% in power conversion efficiency. Due to the VSM technique, short-circuit current density was raised from 24.94 to 33.7mA/cm(2), but both fill factor and open-circuit voltage were approximately unchanged. For the VSM similar results (about 30% increase) were obtained for solar cells fabricated by using mono-crystal line silicon wafers with only conventional background impurities. (c) 2004 Elsevier B.V. All rights reserved.

Structural evaluation of polycrystalline silicon thin films by hot-wire-assisted PECVD

Tungsten wires were introduced into a plasma-enhanced chemical vapor deposition (PECVD) system as a catalyzer: we name this technique 'hot-wire-assisted PECVD' (HW-PECVD). Under constant deposition pressure (p(g)), gas flow ratio and catalyzer position, the effects of the hot wire temperature (T-f) on the structural properties of the poly-Si films have been characterized by X-ray diffraction (XRD), Raman scattering and Fourier-transform infrared (FTIR) spectroscopy. Compared with conventional PECVD, the grain size, crystalline volume fraction (X-e) and deposition rate were all enhanced when a high T-f was used. The best poly-Si film exhibits a preferential (220) orientation, with a full width at half-maximum (FWHM) of 0.2 degrees. The Si-Si TO peak of the Raman scattering spectrum is located at 519.8 cm(-1) with a FWHM of 7.1 cm(-1). The X-c is 0.93. These improvements are mainly the result of promotion of the dissociation of SiH4 and an increase in the atomic H concentration in the gas phase. (C) 2001 Elsevier Science B.V. All rights reserved.

Structural evaluation of polycrystalline silicon thin films by hot-wire-assisted PECVD

Tungsten wires were introduced into a plasma-enhanced chemical vapor deposition (PECVD) system as a catalyzer: we name this technique 'hot-wire-assisted PECVD' (HW-PECVD). Under constant deposition pressure (p(g)), gas flow ratio and catalyzer position, the effects of the hot wire temperature (T-f) on the structural properties of the poly-Si films have been characterized by X-ray diffraction (XRD), Raman scattering and Fourier-transform infrared (FTIR) spectroscopy. Compared with conventional PECVD, the grain size, crystalline volume fraction (X-e) and deposition rate were all enhanced when a high T-f was used. The best poly-Si film exhibits a preferential (220) orientation, with a full width at half-maximum (FWHM) of 0.2 degrees. The Si-Si TO peak of the Raman scattering spectrum is located at 519.8 cm(-1) with a FWHM of 7.1 cm(-1). The X-c is 0.93. These improvements are mainly the result of promotion of the dissociation of SiH4 and an increase in the atomic H concentration in the gas phase. (C) 2001 Elsevier Science B.V. All rights reserved.

青杨(Populus cathayana Rehd.)对逆境胁迫的反应及lea基因的表达分析

杨树具有分布广、适应性强，在生态环境治理和解决木材短缺方面均占有重要位置。青杨(Populus cathayana Rehd.)是青杨派树种的重要成员之一，也是我国的特有种。本研究通过对不同水分梯度的干旱胁迫下青杨形态和生理生化的反应，不同pH值盐碱胁迫下不同海拔和不同气候地区的四个青杨种群在生理生态上的反应差异，以及在干旱和低温胁迫下青杨lea2, lea3组基因表达差异的研究，从形态、生理、生化和分子生物学水平系统地研究了青杨在不同逆境胁迫下的反应和青杨不同种群在盐碱胁迫下的反应差异。主要研究结果如下： 1. 青杨在干旱胁迫下的反应机制：中度和重度干旱胁迫下植株的生长受到明显抑制。表现在光合系统上青杨的净光合同化速率(A)下降，主要原因是气孔导度(gs)，胞间二氧化碳浓度(Ci)下降。另外最大量子产量(Fv/Fm)、光化学猝灭效率(qP)降低反应了干旱胁迫下光合系统II(PSII)受到严重损伤, 而且非光化学猝灭效率(qN)上升，导致可利用化学能产量下降，叶绿体产生淀粉的量减少。qP降低qN上升导致产生的过量电子对光合系统的伤害造成活性氧以及丙二醛(MDA)的含量增加。超微解剖结构显示，干旱胁迫增强时，叶绿体内淀粉粒的数目减少，而且叶绿体、线粒体等细胞器中嗜锇颗粒的数目增加。为清除细胞内的活性氧，植物一般的反应是抗氧化系统酶活性增加，对青杨来讲超氧化物歧化酶(SOD), 抗坏血酸过氧化物酶(APx)活性的增加远大于过氧化物酶(POD)，这显示了在青杨中SOD、APx酶在清除活性氧的作用上大于POD。另外同工酶研究结果显示这些酶活性的升高主要是由于各条同工酶带表达量的增加，而不是诱导新酶带的产生。另外，75% FC水分处理下有些指标非但没有下降，像A和有效光量子产量(Y)的值都略有增加，而且gs同时增加。另外，100% FC比75% FC细胞内淀粉粒的数目少一些，但有少量的嗜锇颗粒。这证明100% FC土壤水分也许并非最适合青杨生长。 2. 盐碱胁迫对不同海拔地区青杨种群的反应差异：青杨高海拔和低海拔种群的各种生理特性随着pH值上升都受到了很大的影响。两种群叶和根中Na+、K+ 含量, Na+/K+比率随着pH值的上升影响显著。在pH值高于10.4时高海拔种群叶和根中Na+/K+比率急剧下降但是低海拔种群中却一直维持在较高水平。两种群中MDA、脯氨酸(Proline)的含量，抗氧化系统酶的活性都受到了严重的影响，证明两个种群都属于盐碱胁迫敏感类型但是高海拔的种群对盐碱胁迫的耐性要高于低海拔。这主要是由于高海拔种群一般具有耐干旱、低温胁迫的能力，而植物的抗逆机制一般都有共通之处。 3. 盐碱胁迫对不同气候地区青杨种群的反应差异：盐碱胁迫下两种群的光合作用受到明显的抑制，具体表现在叶绿素的含量和A 显著下降。净光合速率的下降主要是由于叶片gs，Ci 值降低引起的。与湿润地区的种群相比盐碱胁迫增强时，干旱地区的种群叶绿素含量和光合能力的升高与K+离子含量增加有关。植物维持细胞质高K+/Na+值对植物的抗盐性有很重要的作用。为清除盐碱胁迫产生的活性氧，抗氧化系统酶活性增加。盐碱胁迫下干旱地区的种群在SOD、CAT 和谷胱甘肽还原酶(GR)等酶的活性均显著上升，而湿润地区种群只有谷胱甘肽氧化酶(GST)的活性明显增加，说明干旱种群的抗氧化酶系统在较高盐碱胁迫下的保护作用要强于湿润种群。这主要是由于植物抗盐碱胁迫与抗干旱胁迫在一些方面的机制是一致的，抗旱种群一般也能抵抗一定程度的盐碱胁迫。 4. 青杨lea2、lea3 基因在干旱和低温胁迫下的表达差异：通过荧光定量PCR 分析，lea2、lea3 组基因在干旱和低温胁迫下在mRNA 水平的瞬时表达量明显升高，说明了两基因在青杨耐干旱和低温胁迫上都起显著的作用。而且两基因在干旱胁迫下，表达量的升高和降低的时间近乎同步，表明两基因在干旱胁迫下对植物应急保护机制的启动都发挥着重要的作用。低温胁迫下lea3 基因在mRNA 水平上表达量显著上升的时间要早于lea2，而且lea3 基因的持续作用时间明显长于lea2 组基因，说明了低温胁迫开始时lea3基因在植物应对逆境的作用上要大于lea2 基因。 Poplars play an important role in lumber supply, and are important components of ecosystems due to their wide distribution and well adaptation. Populus cathayana Rehd., which belongs to Populus Sect. Tacamahaca Spach, is one of the most important resources of poplars and is specialist to china. In this study, different altitudes and climates populations of P. cathayana were used as experiment materials to investigate the adaptability to drought and salt-alkali stresses. And the cultures of P. cathayana were used to analyze the lea2 and 3 group genes expression when exposed to drought and low temperature stresses. The results are as follows: 1. A large set of parallel responses to drought stress: Drought stress caused pronounced growth inhibition. A decreased significantly and was mainly the result of gs and Ci down. Besides, Fv/Fm, qP decreased and that reflected the harmful effects to PSII of drought stress. In accordance with qN increasing, decreased useful energy production caused the starch numbers reduction in chloroplast. The qP up and qN down improved the levels of ROS and MDA. Starch numbers in chloroplast reduced and plastoglobuli numbers increased when soil water content decreased. To reduce ROS, the activities of SOD, APX, CAT and PPO were activated. The isozymes results show that the rising activities of the antioxidant enzymes resulted from certain isoform content increased, and not from the new band produced. Interestingly, morphological results show 100%FC maybe wasn’t the favorite water content for P. cathayana growth. 2. Effect of salt-alkali stress on morphological and physiological changes in two different altitudes populations of P. cathayana: We compared the physiological responses of two populations of Populus cathayana Rehder, originating from altitudes 2,840 m and 1,450 m. Our results demonstated that Na+ and K+ contents, and Na+/K+ ratios in leaves and roots are greatly affected by pH values. At pH 10.4, the Na+/K+ ratios in both leaves and roots sharply dropped in the higher altitude population but were always maintained at higher levels in the lower altitude population. The pH values causing maximum malondialdehyde (MDA) level, free proline content and antioxidant enzyme activities were significantly different in two populations. These results indicated that the higher altitude population exhibits greater tolerance to alkalinity stress than does the lower altitude population. 3. Morphological and physiological changes in two different climates populations of P. cathayana when exposed to salt-alkali stress. Salt-alkali stress caused pronounced inhibition of the growth and especially in photosystem. Pigments content and A decreased significantly and at the same time gs and Ci decreased too. Compared with wet climate population, the Chlorophyll content and A increased in drought climate population as pH value rising was related to the K+ content increasing. It is important to resist salt-alkali stress that the K+/Na+ ratio matained at high level in cytoplasm. To reduce ROS content, the SOD, CAT and GR activities rised significantly in drought population but only GST increased in wet population. The drought population showed higher salt-alkali tolerance than the wet population mainly resulted from the fact that drought tolerance was in accordance with salt-alkali tolerance to some extent. 4. The different expressional model of lea2 and lea3 gene when P. cathayana was exposed to drought and cold stress. RT-PCR results show both lea2 and lea3 suddenly expressed significantly in mRNA level under drought and cold stress. The expression level of two genes reached optimal level at the same time. But under cold stress, the earlier significantly rising expressional time and the longer maintained higher level time in lea3 than lea2 elucidated that lea3 may be more important than lea2 in resisting cold stress in short time in P. cathayana.

The effect of annealing treatment on performance of interdiffused organic photovoltaic devices

We fabricated the interdiffused organic photovoltaic devices, which composed of poly (2-methoxy-5-(2'-ethylhexyloxy)-1, 4-phenylenevinylene) (MEH-PPV) and buckminsterfullerene (C-60), by annealing treatment. After annealing, C60 diffused into the MEH-PPV layer, in consequence, MEH-PPV/C-60 interfacial area was increased and their interface became closer proximity. The results lead to reduce reverse-bias saturation current (J(s)), and increase the open-circuit voltage (V-OC) and the short-circuit current (J(SC)).

Organic photovoltaic cell employing organic heterojunction as buffer layer

Hexadecafluorophthalocyaninatocopper (F16CuPc)/zine phthalocyanine (ZnPc) heterojunction layer has been used as buffer layer in organic photovoltaic (OPV) cells based on ZnPc and C-60. The F16CuPc/ZnPc heterojunction with highly conductive property decreased the contact resistance between the indium-tin-oxide anode and the organic layer. As a result, the short-circuit current density and fill factor were increased, and the power-conversion efficiency was improved by over 60%. Therefore, the method provides an effective path to improve the performance of OPV cells.

Efficient tandem polymer photovoltaic cells with two subcells in parallel connection

Tandem polymer photovoltaic cells with the subcells having different absorption characteristics in series connection are widely investigated to enhance absorption coverage over the solar spectrum. Herein. we demonstrate efficient tandem polymer photovoltaic cells with the two stacked subcells comprising different band-gap conjugated polymer and fullerene derivative bulk heterojunction in parallel connection. A semitransparent metal layer combined with inorganic semiconductor compounds is utilized as the intermediate electrode of the two stacked subcells to create the required built-in potential for collecting photo-generated charges. The short-circuit current of the stacked cell is the sum of the subcells and the open-circuit voltage is similar to the subcells.

Solvent-vapor treatment induced performance enhancement of poly(3-hexylthiophene): methanofullerene bulk-heterojunction photovoltaic cells

The authors report enhanced poly(3-hexylthiophene) (P3HT):methanofullerene (PCBM) bulk-heterojunction photovoltaic cells via 1,2-dichlorobenzene (DCB) vapor treatment and thermal annealing. DCB vapor treatment can induce P3HT self-organizing into ordered structure leading to enhanced absorption and high hole mobility. Further annealing the device at a high temperature, PCBM molecules begin to diffuse into aggregates and together with the ordered P3HT phase form bicontinuous pathways in the entire layer for efficient charge separation and transport. Compared to the control device that is merely annealed, optical absorption, short-circuit current, and power conversion efficiency are increased for the DCB vapor-treated cell.