Physical and chemical characterization of yellow mangosteen fruits

The work had as objective the physico-chemical characterization of yellow mangosteen fruits. Six samples of 25 fruits were harvested in yellow mangosteen plants of the Active Germoplasm Bank of São Paulo State University and characterized by evaluation of length and width, weight, percentage and number of seeds per fruit, peel and pulp percentage, soluble solid (SS), titratable acidity (TA), vitamin C and SS/TA rate. Yellow mangosteen fruit is an intermediate vitamin C source with an average content 120.33 mg/100g of fresh fruit and has good technological quality.

Distribution Patterns of Soil Properties in a Rural Mediterranean Area in Northeastern Spain

Soil properties on the Cap de Creus Peninsula, NE Spain depend primarily on scarce agricultural practices and early abandonment. In the study area, 90% of which is mainly covered by Cistus shrubs, 8 environments representing variations in land use/land cover and soil properties at different depths were identified. In each environment variously vegetated areas were selected and sampled. The soils, collected at different depths, were classified as Lithic Xerorthents according to the United States Department of Agriculture system of soil classification (USDA-NRCS 1975). Differences in soil properties were largely found according to the evolution of the plant canopy and the land use history. To identify underlying patterns in soil properties related to environmental evolution, factor analysis was performed and factor scores were used to determine how the factor patterns varied between soil variables, soil depths and selected environments. The three-factor model always accounted for 80% of the total variation in the data at the different soil depths. Organic matter was the more relevant soil property at 0–2 cm depth, whereas active minerals (silt and clay) were found to be the most relevant soil parameters controlling soil dynamics at the other depths investigated. Results showed that vineyards and olive tree soils are poorly developed and present worse conditions for mineral and organic compounds. Analysis of factor scores allowed independent assessment of soils, depth and plant cover and demonstrated that soils present the best physico-chemical characteristics under Erica arborea and meadows. In contrast, soils under Cistus monspeliensis were less nutrient rich and less well structured

Aspectos físico-químicos e biológicos relacionados à ocorrência de Biomphalaria glabrata em focos litorâneos da esquistossomose em Pernambuco

This study analyzes the physico-chemical and biological parameters of freshwater aquatic environments in coastal areas of the State of Pernambuco, Brazil, where snail vector foci and cases of schistosomiasis have been recorded. The tests were carried out using standard methods and sediments were analyzed using the X-ray fluorescence technique. The micro-algae were analyzed using conventional microscopy. The most abundant chemical elements in the sediments were Fe, Ca, Si and Al and there were high concentrations of electrolytes in comparison with data published in the literature. The mean values for salinity (7.7 g/L) and sulfate (489 mg/L) were much higher than normal for freshwater environments. The micro-algae identified are those that inhabit environments with higher levels of salinity. The snail Biomphalaria glabrata seems, therefore, to be more tolerant to salty environments and this constitutes a risk of spread of schistosomiasis.

Caracterização físico-química de complexo de inclusão entre hidroximetilnitrofurazona e hidroxipropil-beta-ciclodextrina

Hydroxymethylnitrofurazone (NFOH) is a prodrug that is active against Trypanosoma cruzi. It however presents low solubility and high toxicity. Hydroxypropyl-beta-cyclodextrin (HP-beta-CD) can be used as a drug-delivery system for NFOH modifying its physico-chemical properties. The aim of this work is to characterize the inclusion complex between NFOH and HP-beta-CD. The rate of NFOH release decreases after complexation and thermodynamic parameters from the solubility isotherm studies revealed that a stable complex is formed (deltaGº= 1.7 kJ/mol). This study focuses on the physico-chemical characterization of a drug-delivery formulation that comes out as a potentially new therapeutic option for Chagas disease treatment.

Análise multivariada de parâmetros físico-químicos em amostras de vinhos tintos comercializados na região metropolitana do Recife

The Brazilian legislation requires analysis of certain parameters to classify a wine and allow its commercialization. Some physico-chemical and some color parameters were determined in this work in samples of different red wines sold in the metropolitan area of Recife. Multivariate analysis comprising principal component analysis and hierarchical cluster analysis was employed to distinguish the analyzed wines. The results for pH, chloride concentration, color parameters and ammonium content were the most important variables for sample classification. It was also possible to classify the wines as soft or dry wines and amongst the soft wines we could determine two out of four winegrowing producers.

Avaliação da qualidade do corpo hídrico do rio Tibagi na região de Ponta Grossa utilizando análise de componentes principais (PCA)

The aim of this paper was to evaluate alterations in the quality of the water of the Tibagi River caused by the urban and industrial activities in the region of Ponta Grossa. The study involved the monitoring of physico-chemical and microbiological parameters of the water body, which were evaluated by a principal components analysis routine. Sample collections were carried out monthly during one year (October of 2005 to September of 2006), at 3 sampling points: upstream and downstream of the industrial district and downstream from the city of Ponta Grossa. The principal components analysis showed the effect of point sources associated with industrial activity, which contribute to the rise of total concentration of amoniacal nitrogen and the reduction of dissolved oxygen in the studied region.

Biodiesel: visão crítica do status atual e perspectivas na academia e na indústria

This article presents a bibliographic review of research carried out on different alternative processes for biodiesel production. The supercritical and subcritical (non catalytic) reaction conditions, the use of solid basic, solid acid and other heterogeneous catalysts, including the use of immobilized enzymes and whole-cell catalysts are also critically compared with the traditional homogeneous alkaline or acid catalysts that are common on industrial applications. Advantages and limitations of all these processes for the transference from the laboratory to the industry are discussed. A correlation of the chemical composition with the quality parameters of the produced biodiesel is done with aim to stablish adequate procedures for the right selection of the raw-material. Castor bean oil is used as an example of inappropriate oil in order to produce a B100 that fulfill all the international physico-chemical quality standards. In this article are presented research results to adequate the values of viscosity, density and iodine number of the castor and soybean biodiesel to the international standard limits by means blending these both biodiesels at the right ratio.

Avaliação (em escala laboratorial) da aplicação do processo eletrolítico em efluente de lagoa de estabilização de esgoto urbano

Physico-chemical and microbiological parameters were evaluated before and after applying an electrolytic process to effluents of a stabilization lagoon, in the presence or absence of "salt". Chlorine generation and bactericidal properties of the treatments were studied following two experiments. Effluent pH increased with electrolysis time. In the absence of "salt", 20 min electrolysis resulted in a COD (Chemical Oxygen Demand) reduction of 44%, along with ca. 99.9% (3 log10 cfu/mL) reduction in total coliforms, heterotrophic bacteria and Escherichia coli. These results indicated that the electrolytic process is a promising complementary technology to improve effluent quality for stabilization lagoons.

Qualidade dos méis produzidos por Melipona fasciculata Smith da região do cerrado maranhense

The honey of Melipona fasciculata is few known in terms of composition, and therefore generally associated with the characteristics of the honey of Apis mellifera. This study contributes to the knowledge of the physico-chemical characteristics of honey of M. fasciculata of the municipalities of Barra do Corda, Jenipapo dos Vieiras, Fernando Falcão, Carolina and Riachão, in cerrado region from Maranhão. The parameters studied were: moisture, pH, acidity, reducing sugars, apparent sucrose, hydroxymethylfurfural, diastase activity, insoluble solids, ash and color. Some of the observed patterns may conform to the established for A. mellifera, but others must be accompanied by a specific legislation.

Surface characterization of chemically modified fiber, wood and paper

Inorganic-organic sol-gel hybrid coatings can be used for improving and modifying properties of wood-based materials. By selecting a proper precursor, wood can be made water repellent, decay-, moisture- or UV-resistant. However, to control the barrier properties of sol-gel coatings on wood substrates against moisture uptake and weathering, an understanding of the surface morphology and chemistry of the deposited sol-gel coatings on wood substrates is needed. Mechanical pulp is used in production of wood-containing printing papers. The physical and chemical fiber surface characteristics, as created in the chosen mechanical pulp manufacturing process, play a key role in controlling the properties of the end-use product. A detailed understanding of how process parameters influence fiber surfaces can help improving cost-effectiveness of pulp and paper production. The current work focuses on physico-chemical characterization of modified wood-based materials with surface sensitive analytical tools. The overall objectives were, through advanced microscopy and chemical analysis techniques, (i) to collect versatile information about the surface structures of Norway spruce thermomechanical pulp fiber walls and understand how they are influenced by the selected chemical treatments, and (ii) to clarify the effect of various sol-gel coatings on surface structural and chemical properties of wood-based substrates. A special emphasis was on understanding the effect of sol-gel coatings on the water repellency of modified wood and paper surfaces. In the first part of the work, effects of chemical treatment on micro- and nano-scale surface structure of 1st stage TMP latewood fibers from Norway spruce were investigated. The chemicals applied were buffered sodium oxalate and hydrochloric acid. The outer and the inner fiber wall layers of the untreated and chemically treated fibers were separately analyzed by light microscopy, atomic force microscopy and field-emission scanning electron microscopy. The selected characterization methods enabled the demonstration of the effect of different treatments on the fiber surface structure, both visually and quantitatively. The outer fiber wall areas appeared as intact bands surrounding the fiber and they were clearly rougher than areas of exposed inner fiber wall. The roughness of the outer fiber wall areas increased most in the sodium oxalate treatment. The results indicated formation of more surface pores on the exposed inner fiber wall areas than on the corresponding outer fiber wall areas as a result of the chemical treatments. The hydrochloric acid treatment seemed to increase the surface porosity of the inner wall areas. In the second part of the work, three silane-based sol-gel hybrid coatings were selected in order to improve moisture resistance of wood and paper substrates. The coatings differed from each other in terms of having different alkyl (CH3–, CH3-(CH2)7–) and fluorocarbon (CF3–) chains attached to the trialkoxysilane sol-gel precursor. The sol-gel coatings were deposited by a wet coating method, i.e. spraying or spreading by brush. The effect of solgel coatings on surface structural and chemical properties of wood-based substrates was studied by using advanced surface analyzing tools: atomic force microscopy, X-ray photoelectron spectroscopy and time-of-flight secondary ion spectroscopy. The results show that the applied sol-gel coatings, deposited as thin films or particulate coatings, have different effects on surface characteristics of wood and wood-based materials. The coating which has a long hydrocarbon chain (CH3-(CH2)7–) attached to the silane backbone (octyltriethoxysilane) produced the highest hydrophobicity for wood and wood-based materials.

Transformation of carbon dioxide to diethyl carbonate over ceria and ceria-supported catalysts

Carbon dioxide is regarded, nowadays, as a primary anthropogenic greenhouse gas leading to global warming. Hence, chemical fixation of CO2 has attracted much attention as a possible way to manufacture useful chemicals. One of the most interesting approaches of CO2 transformations is the synthesis of organic carbonates. Since conventional production technologies of these compounds involve poisonous phosgene and carbon monoxide, there is a need to develop novel synthetic methods that would better match the principles of "Green Chemistry" towards protection of the environment and human health. Over the years, synthesis of dimethyl carbonate was under intensive investigation in the academia and industry. Therefore, this study was entirely directed towards equally important homologue of carbonic esters family namely diethyl carbonate (DEC). Novel synthesis method of DEC starting from ethanol and CO2 over heterogeneous catalysts based on ceria (CeO2) was studied in the batch reactor. However, the plausible drawback of the reaction is thermodynamic limitations. The calculated values revealed that the reaction is exothermic (ΔrHØ298K = ─ 16.6 J/ ) and does not occur spontaneously at rooms temperature (ΔrGØ 298K = 35.85 kJ/mol). Moreover, co-produced water easily shifts the reaction equilibrium towards reactants excluding achievement of high yields of the carbonate. Therefore, in-situ dehydration has been applied using butylene oxide as a chemical water trap. A 9-fold enhancement in the amount of DEC was observed upon introduction of butylene oxide to the reaction media in comparison to the synthetic method without any water removal. This result confirms that reaction equilibrium was shifted in favour of the desired product and thermodynamic boundaries of the reaction were suppressed by using butylene oxide as a water scavenger. In order to obtain insight into the reaction network, the kinetic experiments were performed over commercial cerium oxide. On the basis of the selectivity/conversion profile it could be concluded that the one-pot synthesis of diethyl carbonate from ethanol, CO2 and butylene oxide occurs via a consecutive route involving cyclic carbonate as an intermediate. Since commercial cerium oxide suffers from the deactivation problems already after first reaction cycle, in-house CeO2 was prepared applying room temperature precipitation technique. Variation of the synthesis parameters such as synthesis time, calcination temperature and pH of the reaction solution turned to have considerable influence on the physico-chemical and catalytic properties of CeO2. The increase of the synthesis time resulted in high specific surface area of cerium oxide and catalyst prepared within 50 h exhibited the highest amount of basic sites on its surface. Furthermore, synthesis under pH 11 yielded cerium oxide with the highest specific surface area, 139 m2/g, among all prepared catalysts. Moreover, CeO2─pH11 catalyst demonstrated the best catalytic activity and 2 mmol of DEC was produced at 180 oC and 9 MPa of the final reaction pressure. In addition, ceria-supported onto high specific surface area silicas MCM-41, SBA-15 and silica gel were synthesized and tested for the first time as catalysts in the synthesis of DEC. Deposition of cerium oxide on MCM-41 and SiO2 supports resulted in a substantial increase of the alkalinity of the carrier materials. Hexagonal SBA-15 modified with 20 wt % of ceria exhibited the second highest basicity in the series of supported catalysts. Evaluation of the catalytic activity of ceria-supported catalysts showed that reaction carried out over 20 wt % CeO2-SBA-15 generated the highest amount of DEC.

Chemical characteristics of pequi fruits (Caryocar brasiliense Camb.) native of three municipalities in the State of Goiás - Brazil

In order to assure that the use of cerrado fruits occur in a sustainable way, studies to investigate their characteristics are extremely relevant. In this context, the present study aims to describe some chemical parameters of pequi fruits picked in three municipalities in southwestern Goiás State (Jataí, Rio Verde, and Serranópolis). In each city, two populations of pequi trees - pequizeiros, denominated areas, were selected. In each area, eight trees were selected for the fruit to be picked. The contents of phosphorus, potassium, calcium, magnesium, nitrogen, zinc, and ether extract were determined in the samples. The results demonstrate differences between the chemical characteristics studied for the fruits picked in different areas, which does not seem to vary in a significant way. Comparing the contents obtained in the present study with those required as human daily supply, further studies are recommended aiming at using the pequi fruit as a complementary alternative source of magnesium, manganese, and copper.

Determination of structural and mechanical properties, diffractometry, and thermal analysis of chitosan and hydroxypropylmethylcellulose (HPMC) films plasticized with sorbitol

In this work, the structural, mechanical, diffractometric, and thermal parameters of chitosan-hydroxypropylmethylcellulose (HPMC) films plasticized with sorbitol were studied. Solutions of HPMC (2% w/v) in water and chitosan (2% w/v) in 2% acetic acid solution were prepared. The concentration of sorbitol used was 10% (w/w) to both polymers. This solutions were mixed at different proportions (100/0; 70/30; 50/50; 30/70, and 0/100) of chitosan and HPMC, respectively, and 20 mL was cast in Petri dishes for further analysis of dried films. The miscibility of polymers was assessed by X-ray diffraction, scanning electronic microscopy (SEM), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The results obtained indicate that the films are not fully miscible at a dry state despite the weak hydrogen bonding between the polymer functional groups.

Physicochemical characteristics of organic honey samples of africanized honeybees from Parana River islands

This research was carried out to evaluate the physicochemical composition of organic honey in Paraná River islands, in Porto Brasílio, State of Paraná. Honey was harvested directly from super of the colonies in three apiaries spread in the Floresta and Laranjeira Islands, from August 2005 to August 2006. Twenty-four samples of organic honey produced by Africanized honeybees were evaluated. The following parameters were analyzed: pH, acidity, formol index, hydroxymethylfurfural, ashes, color, electric conductivity and moisture. Three replications per sample were performed for laboratorial analysis, giving the means and standard deviation. Most honey samples were in conformity with the Normative Instruction 11 from October 20, 2000. However, 4.17% were not in accordance with the moisture standards, 8.33% showed high concentrations of hydroxymethylfurfural, thus, totalizing 12.50% of non-complying samples. Nevertheless, 87.50% of the analyzed honey samples are within the standards, being characterized as an organic product of excellent quality, with good commercialization perspectives in the market.

Influence of harvest year in the physicochemical properties and antioxidant activity of flaxseed hull oils from Tunisia

The objective of this research was to determine the effect of five years on physico-chemical characteristics and antioxidant activity of flaxseed hull oils. Oil and protein on flaxseed hull varied between 20.15 and 22.56 and 17.45 and 19.14, respectively. The albumin fraction dominated the seed hull protein composition (44 - 47%). Flaxseed hull oils showed significantly high unsaturated to saturated fatty acid ratios (6.61 - 8.36) and calculated oxidizability (Cox) values (10.88 - 12.30). The physiochemical parameters determined included saponification value (SV) (174 -182 mg KOH/g), unsaponifiable matter (UM) (1.32 - 1.64%), peroxide value (PV) (1.70 - 2.20 mequiv/kg), Oxidation value (OV) (4.40 - 5.90) and oil stability (1.10 - 1.42 h). The highest content of total phenolic acids and total tocopherols were recorded on hull sample collected in 2008. Flavanoid content ranged from 11 to 19 mg/100 g oil. Antioxidant activity differed significantly; the greatest inhibition (61.38%) was for the hull sample collected in 2008.