Advanced signal and receiver design for next generation OFDM systems

This thesis deal with the design of advanced OFDM systems. Both waveform and receiver design have been treated. The main scope of the Thesis is to study, create, and propose, ideas and novel design solutions able to cope with the weaknesses and crucial aspects of modern OFDM systems. Starting from the the transmitter side, the problem represented by low resilience to non-linear distortion has been assessed. A novel technique that considerably reduces the Peak-to-Average Power Ratio (PAPR) yielding a quasi constant signal envelope in the time domain (PAPR close to 1 dB) has been proposed.The proposed technique, named Rotation Invariant Subcarrier Mapping (RISM),is a novel scheme for subcarriers data mapping,where the symbols belonging to the modulation alphabet are not anchored, but maintain some degrees of freedom. In other words, a bit tuple is not mapped on a single point, rather it is mapped onto a geometrical locus, which is totally or partially rotation invariant. The final positions of the transmitted complex symbols are chosen by an iterative optimization process in order to minimize the PAPR of the resulting OFDM symbol. Numerical results confirm that RISM makes OFDM usable even in severe non-linear channels. Another well known problem which has been tackled is the vulnerability to synchronization errors. Indeed in OFDM system an accurate recovery of carrier frequency and symbol timing is crucial for the proper demodulation of the received packets. In general, timing and frequency synchronization is performed in two separate phases called PRE-FFT and POST-FFT synchronization. Regarding the PRE-FFT phase, a novel joint symbol timing and carrier frequency synchronization algorithm has been presented. The proposed algorithm is characterized by a very low hardware complexity, and, at the same time, it guarantees very good performance in in both AWGN and multipath channels. Regarding the POST-FFT phase, a novel approach for both pilot structure and receiver design has been presented. In particular, a novel pilot pattern has been introduced in order to minimize the occurrence of overlaps between two pattern shifted replicas. This allows to replace conventional pilots with nulls in the frequency domain, introducing the so called Silent Pilots. As a result, the optimal receiver turns out to be very robust against severe Rayleigh fading multipath and characterized by low complexity. Performance of this approach has been analytically and numerically evaluated. Comparing the proposed approach with state of the art alternatives, in both AWGN and multipath fading channels, considerable performance improvements have been obtained. The crucial problem of channel estimation has been thoroughly investigated, with particular emphasis on the decimation of the Channel Impulse Response (CIR) through the selection of the Most Significant Samples (MSSs). In this contest our contribution is twofold, from the theoretical side, we derived lower bounds on the estimation mean-square error (MSE) performance for any MSS selection strategy,from the receiver design we proposed novel MSS selection strategies which have been shown to approach these MSE lower bounds, and outperformed the state-of-the-art alternatives. Finally, the possibility of using of Single Carrier Frequency Division Multiple Access (SC-FDMA) in the Broadband Satellite Return Channel has been assessed. Notably, SC-FDMA is able to improve the physical layer spectral efficiency with respect to single carrier systems, which have been used so far in the Return Channel Satellite (RCS) standards. However, it requires a strict synchronization and it is also sensitive to phase noise of local radio frequency oscillators. For this reason, an effective pilot tone arrangement within the SC-FDMA frame, and a novel Joint Multi-User (JMU) estimation method for the SC-FDMA, has been proposed. As shown by numerical results, the proposed scheme manages to satisfy strict synchronization requirements and to guarantee a proper demodulation of the received signal.

Innovative architecture of on-board and on-ground radio systems for space communication

The radio communication system is one of the most critical system of the overall satellite platform: it often represents the only way of communication, between a spacecraft and the Ground Segment or among a constellation of satellites. This thesis focuses on specific innovative architectures for on-board and on-ground radio systems. In particular, this work is an integral part of a space program started in 2004 at the University of Bologna, Forlì campus, which led to the completion of the microsatellite ALMASat-1, successfully launched on-board the VEGA maiden flight. The success of this program led to the development of a second microsatellite, named ALMASat-EO, a three-axis stabilized microsatellite able to capture images of the Earth surface. Therefore, the first objective of this study was focused on the investigation of an innovative, efficient and low cost architecture for on-board radio communication systems. The TT&C system and the high data rate transmitter for images downlink design and realization are thoroughly described in this work, together with the development of the embedded hardware and the adopted antenna systems. Moreover, considering the increasing interest in the development of constellations of microsatellite, in particular those flying in close formations, a careful analysis has been carried out for the development of innovative communication protocols for inter-satellite links. Furthermore, in order to investigate the system aspects of space communications, a study has been carried out at ESOC having as objective the design, implementation and test of two experimental devices for the enhancement of the ESA GS. Thus, a significant portion of this thesis is dedicated to the description of the results of a method for improving the phase stability of GS radio frequency equipments by means of real-time phase compensation and a new way to perform two antennas arraying tracking using already existing ESA tracking stations facilities.

Particle filtering for indoor RFID tag tracking

In this paper, we propose a particle filtering (PF) method for indoor tracking using radio frequency identification (RFID) based on aggregated binary measurements. We use an Ultra High Frequency (UHF) RFID system that is composed of a standard RFID reader, a large set of standard passive tags whose locations are known, and a newly designed, special semi-passive tag attached to an object that is tracked. This semi-passive tag has the dual ability to sense the backscatter communication between the reader and other passive tags which are in its proximity and to communicate this sensed information to the reader using backscatter modulation. We refer to this tag as a sense-a-tag (ST). Thus, the ST can provide the reader with information that can be used to determine the kinematic parameters of the object on which the ST is attached. We demonstrate the performance of the method with data obtained in a laboratory environment.

Novel Inductor‐less Conversion Strategy Based on Multiphase Transformer‐Coupled Converters: Analysis, Design and Applications

There are many the requirements that modern power converters should fulfill. Most of the applications where these converters are used, demand smaller converters with high efficiency, improved power density and a fast dynamic response. For instance, loads like microprocessors demand aggressive current steps with very high slew rates (100A/mus and higher); besides, during these load steps, the supply voltage of the microprocessor should be kept within tight limits in order to ensure its correct performance. The accomplishment of these requirements is not an easy task; complex solutions like advanced topologies - such as multiphase converters- as well as advanced control strategies are often needed. Besides, it is also necessary to operate the converter at high switching frequencies and to use capacitors with high capacitance and low ESR. Improving the dynamic response of power converters does not rely only on the control strategy but also the power topology should be suited to enable a fast dynamic response. Moreover, in later years, a fast dynamic response does not only mean accomplishing fast load steps but output voltage steps are gaining importance as well. At least, two applications that require fast voltage changes can be named: Low power microprocessors. In these devices, the voltage supply is changed according to the workload and the operating frequency of the microprocessor is changed at the same time. An important reduction in voltage dependent losses can be achieved with such changes. This technique is known as Dynamic Voltage Scaling (DVS). Another application where important energy savings can be achieved by means of changing the supply voltage are Radio Frequency Power Amplifiers. For example, RF architectures based on ‘Envelope Tracking’ and ‘Envelope Elimination and Restoration’ techniques can take advantage of voltage supply modulation and accomplish important energy savings in the power amplifier. However, in order to achieve these efficiency improvements, a power converter with high efficiency and high enough bandwidth (hundreds of kHz or even tens of MHz) is necessary in order to ensure an adequate supply voltage. The main objective of this Thesis is to improve the dynamic response of DC-DC converters from the point of view of the power topology. And the term dynamic response refers both to the load steps and the voltage steps; it is also interesting to modulate the output voltage of the converter with a specific bandwidth. In order to accomplish this, the question of what is it that limits the dynamic response of power converters should be answered. Analyzing this question leads to the conclusion that the dynamic response is limited by the power topology and specifically, by the filter inductance of the converter which is found in series between the input and the output of the converter. The series inductance is the one that determines the gain of the converter and provides the regulation capability. Although the energy stored in the filter inductance enables the regulation and the capability of filtering the output voltage, it imposes a limitation which is the concern of this Thesis. The series inductance stores energy and prevents the current from changing in a fast way, limiting the slew rate of the current through this inductor. Different solutions are proposed in the literature in order to reduce the limit imposed by the filter inductor. Many publications proposing new topologies and improvements to known topologies can be found in the literature. Also, complex control strategies are proposed with the objective of improving the dynamic response in power converters. In the proposed topologies, the energy stored in the series inductor is reduced; examples of these topologies are Multiphase converters, Buck converter operating at very high frequency or adding a low impedance path in parallel with the series inductance. Control techniques proposed in the literature, focus on adjusting the output voltage as fast as allowed by the power stage; examples of these control techniques are: hysteresis control, V 2 control, and minimum time control. In some of the proposed topologies, a reduction in the value of the series inductance is achieved and with this, the energy stored in this magnetic element is reduced; less stored energy means a faster dynamic response. However, in some cases (as in the high frequency Buck converter), the dynamic response is improved at the cost of worsening the efficiency. In this Thesis, a drastic solution is proposed: to completely eliminate the series inductance of the converter. This is a more radical solution when compared to those proposed in the literature. If the series inductance is eliminated, the regulation capability of the converter is limited which can make it difficult to use the topology in one-converter solutions; however, this topology is suitable for power architectures where the energy conversion is done by more than one converter. When the series inductor is eliminated from the converter, the current slew rate is no longer limited and it can be said that the dynamic response of the converter is independent from the switching frequency. This is the main advantage of eliminating the series inductor. The main objective, is to propose an energy conversion strategy that is done without series inductance. Without series inductance, no energy is stored between the input and the output of the converter and the dynamic response would be instantaneous if all the devices were ideal. If the energy transfer from the input to the output of the converter is done instantaneously when a load step occurs, conceptually it would not be necessary to store energy at the output of the converter (no output capacitor COUT would be needed) and if the input source is ideal, the input capacitor CIN would not be necessary. This last feature (no CIN with ideal VIN) is common to all power converters. However, when the concept is actually implemented, parasitic inductances such as leakage inductance of the transformer and the parasitic inductance of the PCB, cannot be avoided because they are inherent to the implementation of the converter. These parasitic elements do not affect significantly to the proposed concept. In this Thesis, it is proposed to operate the converter without series inductance in order to improve the dynamic response of the converter; however, on the other side, the continuous regulation capability of the converter is lost. It is said continuous because, as it will be explained throughout the Thesis, it is indeed possible to achieve discrete regulation; a converter without filter inductance and without energy stored in the magnetic element, is capable to achieve a limited number of output voltages. The changes between these output voltage levels are achieved in a fast way. The proposed energy conversion strategy is implemented by means of a multiphase converter where the coupling of the phases is done by discrete two-winding transformers instead of coupledinductors since transformers are, ideally, no energy storing elements. This idea is the main contribution of this Thesis. The feasibility of this energy conversion strategy is first analyzed and then verified by simulation and by the implementation of experimental prototypes. Once the strategy is proved valid, different options to implement the magnetic structure are analyzed. Three different discrete transformer arrangements are studied and implemented. A converter based on this energy conversion strategy would be designed with a different approach than the one used to design classic converters since an additional design degree of freedom is available. The switching frequency can be chosen according to the design specifications without penalizing the dynamic response or the efficiency. Low operating frequencies can be chosen in order to favor the efficiency; on the other hand, high operating frequencies (MHz) can be chosen in order to favor the size of the converter. For this reason, a particular design procedure is proposed for the ‘inductorless’ conversion strategy. Finally, applications where the features of the proposed conversion strategy (high efficiency with fast dynamic response) are advantageus, are proposed. For example, in two-stage power architectures where a high efficiency converter is needed as the first stage and there is a second stage that provides the fine regulation. Another example are RF power amplifiers where the voltage is modulated following an envelope reference in order to save power; in this application, a high efficiency converter, capable of achieving fast voltage steps is required. The main contributions of this Thesis are the following: The proposal of a conversion strategy that is done, ideally, without storing energy in the magnetic element. The validation and the implementation of the proposed energy conversion strategy. The study of different magnetic structures based on discrete transformers for the implementation of the proposed energy conversion strategy. To elaborate and validate a design procedure. To identify and validate applications for the proposed energy conversion strategy. It is important to remark that this work is done in collaboration with Intel. The particular features of the proposed conversion strategy enable the possibility of solving the problems related to microprocessor powering in a different way. For example, the high efficiency achieved with the proposed conversion strategy enables it as a good candidate to be used for power conditioning, as a first stage in a two-stage power architecture for powering microprocessors.

Low-thickness high-quality aluminum nitride films for super high frequency solidly mounted resonators

We investigate the sputter growth of very thin aluminum nitride (AlN) films on iridium electrodes for electroacoustic devices operating in the super high frequency range. Superior crystal quality and low stress films with thicknesses as low as 160 nm are achieved after a radio frequency plasma treatment of the iridium electrode followed by a two-step alternating current reactive magnetron sputtering of an aluminum target, which promotes better conditions for the nucleation of well textured AlN films in the very first stages of growth. Solidly mounted resonators tuned around 8 GHz with effective electromechanical coupling factors of 5.8% and quality factors Q up to 900 are achieved.

Processing of ultra-wideband low-frequency signals, for application in Foliage Penetration (FOPEN) Synthetic Aperture Radar (SAR) systems

Foliage Penetration (FOPEN) radar systems were introduced in 1960, and have been constantly improved by several organizations since that time. The use of Synthetic Aperture Radar (SAR) approaches for this application has important advantages, due to the need for high resolution in two dimensions. The design of this type of systems, however, includes some complications that are not present in standard SAR systems. FOPEN SAR systems need to operate with a low central frequency (VHF or UHF bands) in order to be able to penetrate the foliage. High bandwidth is also required to obtain high resolution. Due to the low central frequency, large integration angles are required during SAR image formation, and therefore the Range Migration Algorithm (RMA) is used. This project thesis identifies the three main complications that arise due to these requirements. First, a high fractional bandwidth makes narrowband propagation models no longer valid. Second, the VHF and UHF bands are used by many communications systems. The transmitted signal spectrum needs to be notched to avoid interfering them. Third, those communications systems cause Radio Frequency Interference (RFI) on the received signal. The thesis carries out a thorough analysis of the three problems, their degrading effects and possible solutions to compensate them. The UWB model is applied to the SAR signal, and the degradation induced by it is derived. The result is tested through simulation of both a single pulse stretch processor and the complete RMA image formation. Both methods show that the degradation is negligible, and therefore the UWB propagation effect does not need compensation. A technique is derived to design a notched transmitted signal. Then, its effect on the SAR image formation is evaluated analytically. It is shown that the stretch processor introduces a processing gain that reduces the degrading effects of the notches. The remaining degrading effect after processing gain is assessed through simulation, and an experimental graph of degradation as a function of percentage of nulled frequencies is obtained. The RFI is characterized and its effect on the SAR processor is derived. Once again, a processing gain is found to be introduced by the receiver. As the RFI power can be much higher than that of the desired signal, an algorithm is proposed to remove the RFI from the received signal before RMA processing. This algorithm is a modification of the Chirp Least Squares Algorithm (CLSA) explained in [4], which adapts it to deramped signals. The algorithm is derived analytically and then its performance is evaluated through simulation, showing that it is effective in removing the RFI and reducing the degradation caused by both RFI and notching. Finally, conclusions are drawn as to the importance of each one of the problems in SAR system design.

Design of a Two-Phase buck converter with fourth-order output filter for envelope amplifiers of limited bandwidth

The use of techniques such as envelope tracking (ET) and envelope elimination and restoration (EER) can improve the efficiency of radio frequency power amplifiers (RFPA). In both cases, high-bandwidth DC/DC converters called envelope amplifiers (EA) are used to modulate the supply voltage of the RFPA. This paper addresses the analysis and design of a modified two-phase Buck converter optimized to operate as EA. The effects of multiphase operation on the tracking capabilities are analyzed. The use of a fourth-order output filter is proposed to increase the attenuation of the harmonics generated by the PWM operation, thus allowing a reduction of the ratio between the switching frequency and the converter bandwidth. The design of the output filter is addressed considering envelope tracking accuracy and distortion caused by the side bands arising from the nonlinear modulation process. Finally, the proposed analysis and design methods are supported by simulation results, as well as demonstrated by experiments obtained using two 100-W, 10-MHz, two-phase Buck EAs capable of accurately tracking a 1.5-MHz bandwidth OFDM signal.

Telemetría de vehículos FSAE con microcontrolador PIC32 y transceptor de radio CC1101

Quizás el campo de las telecomunicaciones sea uno de los campos en el que más se ha progresado en este último siglo y medio, con la ayuda de otros campos de la ciencia y la técnica tales como la computación, la física electrónica, y un gran número de disciplinas, que se han utilizado estos últimos 150 años en conjunción para mejorarse unas con la ayuda de otras. Por ejemplo, la química ayuda a comprender y mejorar campos como la medicina, que también a su vez se ve mejorada por los progresos en la electrónica creados por los físicos y químicos, que poseen herramientas más potentes para calcular y simular debido a los progresos computacionales. Otro de los campos que ha sufrido un gran avance en este último siglo es el de la automoción, aunque estancados en el motor de combustión, los vehículos han sufrido enormes cambios debido a la irrupción de los avances en la electrónica del automóvil con multitud de sistemas ya ampliamente integrados en los vehículos actuales. La Formula SAE® o Formula Student es una competición de diseño, organizada por la SAE International (Society of Automotive Engineers) para estudiantes de universidades de todo el mundo que promueve la ingeniería a través de una competición donde los miembros del equipo diseñan, construyen, desarrollan y compiten en un pequeño y potente monoplaza. En el ámbito educativo, evitando el sistema tradicional de clases magistrales, se introducen cambios en las metodologías de enseñanza y surge el proyecto de la Fórmula Student para lograr una mejora en las acciones formativas, que permitan ir incorporando nuevos objetivos y diseñar nuevas situaciones de aprendizaje que supongan una oportunidad para el desarrollo de competencias de los alumnos, mejorar su formación como ingenieros y contrastar sus progresos compitiendo con las mejores universidades del mundo. En este proyecto se pretende dotar a los alumnos de las escuelas de ingeniería de la UPM que desarrollan el vehículo de FSAE de una herramienta de telemetría con la que evaluar y probar comportamiento del vehículo de FSAE junto con sus subsistemas que ellos mismos diseñan, con el objetivo de evaluar el comportamiento, introducir mejoras, analizar resultados de una manera más rápida y cómoda, con el objetivo de poder progresar más rápidamente en su desarrollo, recibiendo y almacenando una realimentación directa e instantánea del funcionamiento mediante la lectura de los datos que circulan por el bus CAN del vehículo. También ofrece la posibilidad de inyectar datos a los sistemas conectados al bus CAN de manera remota. Se engloba en el conjunto de proyectos de la FSAE, más concretamente en los basados en la plataforma PIC32 y propone una solución conjunta con otros proyectos o también por sí sola. Para la ejecución del proyecto se fabricó una placa compuesta de dos placas de circuito impreso, la de la estación base que envía comandos, instrucciones y datos para inyectar en el bus CAN del vehículo mediante radiofrecuencia y la placa que incorpora el vehículo que envía las tramas que circulan por el bus CAN del vehículo con los identificadores deseados, ejecuta los comandos recibidos por radiofrecuencia y salva las tramas CAN en una memoria USB o SD Card. Las dos PCBs constituyen el hardware del proyecto. El software se compone de dos programas. Un programa para la PCB del vehículo que emite los datos a la estación base, codificado en lenguaje C con ayuda del entorno de desarrollo MPLAB de Microchip. El otro programa hecho con LabView para la PCB de la estación base que recibe los datos provenientes del vehículo y los interpreta. Se propone un hardware y una capa o funciones de software para los microcontroladores PIC32 (similar al de otros proyectos del FSAE) para la transmisión de las tramas del bus CAN del vehículo de manera inalámbrica a una estación base, capaz de insertar tramas en el bus CAN del vehículo enviadas desde la estación base. También almacena estas tramas CAN en un dispositivo USB o SD Card situado en el vehículo. Para la transmisión de los datos se hizo un estudio de las frecuencias de transmisión, la legislación aplicable y los tipos de transceptores. Se optó por utilizar la banda de radiofrecuencia de uso común ISM de 433MHz mediante el transceptor integrado CC110L de Texas Instruments altamente configurable y con interfaz SPI. Se adquirieron dos parejas de módulos compatibles, con amplificador de potencia o sin él. LabView controla la estación que recoge las tramas CAN vía RF y está dotada del mismo transceptor de radio junto con un puente de comunicaciones SPI-USB, al que se puede acceder de dos diferentes maneras, mediante librerías dll, o mediante NI-VISA con transferencias RAW-USB. La aplicación desarrollada posee una interfaz configurable por el usuario para la muestra de los futuros sensores o actuadores que se incorporen en el vehículo y es capaz de interpretar las tramas CAN, mostrarlas, gráfica, numéricamente y almacenar esta información, como si fuera el cuadro de instrumentos del vehículo. Existe una limitación de la velocidad global del sistema en forma de cuello de botella que se crea debido a las limitaciones del transceptor CC110L por lo que si no se desea filtrar los datos que se crean necesarios, sería necesario aumentar el número de canales de radio para altas ocupaciones del bus CAN. Debido a la pérdida de relaciones con el INSIA, no se pudo probar de manera real en el propio vehículo, pero se hicieron pruebas satisfactorias (hasta 1,6 km) con una configuración de tramas CAN estándar a una velocidad de transmisión de 1 Mbit/s y un tiempo de bit de 1 microsegundo. El periférico CAN del PIC32 se programará para cumplir con estas especificaciones de la ECU del vehículo, que se presupone que es la MS3 Sport de Bosch, de la que LabView interpretará las tramas CAN recibidas de manera inalámbrica. Para poder probar el sistema, ha sido necesario reutilizar el hardware y adaptar el software del primer prototipo creado, que emite tramas CAN preprogramadas con una latencia también programable y que simulará al bus CAN proporcionando los datos a transmitir por el sistema que incorpora el vehículo. Durante el desarrollo de este proyecto, en las etapas finales, el fabricante del puente de comunicaciones SPI-USB MCP2210 liberó una librería (dll) compatible y sin errores, por lo que se nos ofrecía una oportunidad interesante para la comparación de las velocidades de acceso al transceptor de radio, que se presuponía y se comprobó más eficiente que la solución ya hecha mediante NI-VISA. ABSTRACT. The Formula SAE competition is an international university applied to technological innovation in vehicles racing type formula, in which each team, made up of students, should design, construct and test a prototype each year within certain rules. The challenge of FSAE is that it is an educational project farther away than a master class. The goal of the present project is to make a tool for other students to use it in his projects related to FSAE to test and improve the vehicle, and, the improvements that can be provided by the electronics could be materialized in a victory and win the competition with this competitive advantage. A telemetry system was developed. It sends the data provided by the car’s CAN bus through a radio frequency transceiver and receive commands to execute on the system, it provides by a base station on the ground. Moreover, constant verification in real time of the status of the car or data parameters like the revolutions per minute, pressure from collectors, water temperature, and so on, can be accessed from the base station on the ground, so that, it could be possible to study the behaviour of the vehicle in early phases of the car development. A printed circuit board, composed of two boards, and two software programs in two different languages, have been developed, and built for the project implementation. The software utilized to design the PCB is Orcad10.5/Layout. The base station PCB on a PC receives data from the PCB connected to the vehicle’s CAN bus and sends commands like set CAN filters or masks, activate data logger or inject CAN frames. This PCB is connected to a PC via USB and contains a bridge USB-SPI to communicate with a similar transceiver on the vehicle PCB. LabView controls this part of the system. A special virtual Instrument (VI) had been created in order to add future new elements to the vehicle, is a dashboard, which reads the data passed from the main VI and represents them graphically to studying the behaviour of the car on track. In this special VI other alums can make modifications to accommodate the data provided from the vehicle CAN’s bus to new elements on the vehicle, show or save the CAN frames in the form or format they want. Two methods to access to SPI bus of CC110l RF transceiver over LabView have been developed with minimum changes between them. Access through NI-VISA (Virtual Instrument Software Architecture) which is a standard for configuring, programming, USB interfaces or other devices in National Instruments LabView. And access through DLL (dynamic link library) supplied by the manufacturer of the bridge USB-SPI, Microchip. Then the work is done in two forms, but the dll solution developed shows better behaviour, and increase the speed of the system because has less overload of the USB bus due to a better efficiency of the dll solution versus VISA solution. The PCB connected to the vehicle’s CAN bus receives commands from the base station PCB on a PC, and, acts in function of the command or execute actions like to inject packets into CAN bus or activate data logger. Also sends over RF the CAN frames present on the bus, which can be filtered, to avoid unnecessary radio emissions or overflowing the RF transceiver. This PCB consists of two basic pieces: A microcontroller with 32 bit architecture PIC32MX795F512L from Microchip and the radio transceiver integrated circuit CC110l from Texas Instruments. The PIC32MX795F512L has an integrated CAN and several peripherals like SPI controllers that are utilized to communicate with RF transceiver and SD Card. The USB controller on the PIC32 is utilized to store CAN data on a USB memory, and change notification peripheral is utilized like an external interrupt. Hardware for other peripherals is accessible. The software part of this PCB is coded in C with MPLAB from Microchip, and programming over PICkit 3 Programmer, also from Microchip. Some of his libraries have been modified to work properly with this project and other was created specifically for this project. In the phase for RF selection and design is made a study to clarify the general aspects of regulations for the this project in order to understand it and select the proper band, frequency, and radio transceiver for the activities developed in the project. From the different options available it selects a common use band ICM, with less regulation and free to emit with restrictions and disadvantages like high occupation. The transceiver utilized to transmit and receive the data CC110l is an integrated circuit which needs fewer components from Texas Instruments and it can be accessed through SPI bus. Basically is a state machine which changes his state whit commands received over an SPI bus or internal events. The transceiver has several programmable general purpose Inputs and outputs. These GPIOs are connected to PIC32 change notification input to generate an interrupt or connected to GPIO to MCP2210 USB-SPI bridge to inform to the base station for a packet received. A two pair of modules of CC110l radio module kit from different output power has been purchased which includes an antenna. This is to keep away from fabrication mistakes in RF hardware part or designs, although reference design and gerbers files are available on the webpage of the chip manufacturer. A neck bottle is present on the complete system, because the maximum data rate of CC110l transceiver is a half than CAN bus data rate, hence for high occupation of CAN bus is recommendable to filter the data or add more radio channels, because the buffers can’t sustain this load along the time. Unfortunately, during the development of the project, the relations with the INSIA, who develops the vehicle, was lost, for this reason, will be made impossible to test the final phases of the project like integration on the car, final test of integration, place of the antenna, enclosure of the electronics, connectors selection, etc. To test or evaluate the system, it was necessary to simulate the CAN bus with a hardware to feed the system with entry data. An early hardware prototype was adapted his software to send programed CAN frames at a fixed data rate and certain timing who simulate several levels of occupation of the CAN Bus. This CAN frames emulates the Bosch ECU MS3 Sport.

Citizen's band radio safety evaluation project. Volume I - technical summary. Final report.

National Highway Traffic Safety Administration, Office of Driver and Pedestrian Programs, Washington, D.C.

Monitor - training program for CB radio emergency monitors. 1: course guide.

National Highway Traffic Safety Administration, Washington, D.C.

Monitor - training program for CB radio emergency monitors. 3: student study guide.

National Highway Traffic Safety Administration, Washington, D.C.

Traffic safety demonstration program modeling system. Volume III: citizens band radio model. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Citizen's band radio highway safety evaluation project.

Mode of access: Internet.

Citizen's band radio safety evaluation project. Volume II. Final report.

National Highway Traffic Safety Administration, Office of Driver and Pedestrian Programs, Washington, D.C.

Monitor - training program for CB radio emergency monitors. 2 lesson plan.

National Highway Traffic Safety Administration, Washington, D.C.