Numerical study of graphene as a channel material for field-effect transistors

Graphene excellent properties make it a promising candidate for building future nanoelectronic devices. Nevertheless, the absence of an energy gap is an open problem for the transistor application. In this thesis, graphene nanoribbons and pattern-hydrogenated graphene, two alternatives for inducing an energy gap in graphene, are investigated by means of numerical simulations. A tight-binding NEGF code is developed for the simulation of GNR-FETs. To speed up the simulations, the non-parabolic effective mass model and the mode-space tight-binding method are developed. The code is used for simulation studies of both conventional and tunneling FETs. The simulations show the great potential of conventional narrow GNR-FETs, but highlight at the same time the leakage problems in the off-state due to various tunneling mechanisms. The leakage problems become more severe as the width of the devices is made larger, and thus the band gap smaller, resulting in a poor on/off current ratio. The tunneling FET architecture can partially solve these problems thanks to the improved subthreshold slope; however, it is also shown that edge roughness, unless well controlled, can have a detrimental effect in the off-state performance. In the second part of this thesis, pattern-hydrogenated graphene is simulated by means of a tight-binding model. A realistic model for patterned hydrogenation, including disorder, is developed. The model is validated by direct comparison of the momentum-energy resolved density of states with the experimental angle-resolved photoemission spectroscopy. The scaling of the energy gap and the localization length on the parameters defining the pattern geometry is also presented. The results suggest that a substantial transport gap can be attainable with experimentally achievable hydrogen concentration.

Extended arm polyphenylene dendrimers

In order to eliminate the de Gennes packing problem, which usually limits the attainable size of dendrimers, a new branching unit containing para-tetraphenylene ethynyl arms has been synthesized and utilized in the preparation of dendrimers of the Müllen type. The divergent principle of synthesis, based on the Dilthey reaction, could be carried up to sixth generation which contains 2776 benzene rings and possesses a diameter in the 27 nm range ("exploded dendrimer"). Monodispersity and dimensions of this and the lower generation species have been studied by MALDI-TOF MS (including the very recent superconducting tunnel junction detector), by size-exclusion chromatography, dynamic light scattering, transmission electron microscopy, and atomic force microscopy. Interesting features, apart from the huge dimension, are the low density and high porosity of these giant molecules which cause extensive aggregation in the gas phase, flattening on solid support (AFM) and the ready incorporation of guest molecules in the condensed phase. Since the synthesis of the para-tetraphenylene arms is quite elaborate, similar dendrimers containing para-terphenylene arms have been prepared; they are accessible more economically ("semi-exploded dendrimers"). It has been shown that they in several aspects mimic the features of the "exploded dendrimers". In order to take advantage of the presence of large internal cavities in this dendrimer type, dendrons containing -C≡C- triple bonds have also been incorporated. Surprisingly, they are readily hydrogenated under the condition of heterogeneous catalysis (Pd/C) which demonstrates the large size of the cavities. As revealed by a quartz microbalance study the post-hydrogenation dendrimers are less prone to incorporate guest molecules than before hydrogenation. Obviously, the more flexible nature of the former reduces porosity, it also leads to significant shrinkage. An interesting perspective is the use of homogeneous hydrogenation catalysts of variable size with the aim of determining the dimension of internal free space.

Die Synthese von Glycopeptiden und Glycopeptid-Protein-Konjugaten mit einer Partialstruktur des tumorassoziierten Mucins MUC1 zur Entwicklung von Tumorvakzinen

„Synthese von Glycopeptiden und Glycopeptid-Protein-Konjugaten mit einer Partialstruktur des tumorassoziierten Mucins MUC1 zur Entwicklung von Tumorvakzinen“ Das Glycoprotein MUC1 ist in Tumorepithelzellen sonderlich stark überexprimiert und wegen der vorzeitig einsetzenden Sialylierung sind die Saccharid-Epitope der O-Glycanketten stark verkürzt (sog. tumorassoziierte Antigene). Dadurch werden auch bisher verborgene Peptidepitope des Glycoprotein-Rückgrates auf der Zelloberfläche der Epithelzellen zugänglich, die als fremd von den Zellen des Immunsystems erkannt werden können. Dies macht das MUC1-Zelloberfächenmolekül zu einem Zielmolekül in der Entwicklung von Tumorvakzinen. Diese beiden strukturellen Besonderheiten wurden in der Synthese von Glycohexadecapeptiden verbunden, indem die veränderten tumorassoziierten Saccharidstrukturen TN-, STN- und T-Antigen als Glycosylaminosäure-Festphasenbausteine synthetisiert wurden und in das Peptidepitop der Wiederholungseinheit des MUC1 durch Glycopeptid-Festphasensynthese eingebaut wurden. Wegen der inhärenten schwachen Immunogenität der kurzen Glycopeptide müssen die synthetisierten Glycopeptidstrukturen an ein Trägerprotein, welches das Immunsystem stimuliert, gebunden werden. Zur Anbindung der Glycopeptide ist ein selektives Kupplungsverfahren nötig, um definierte und strukturell einheitliche Glycopeptid-Protein-Konjugate zu erhalten. Es konnte eine neue Methode entwickelt werden, bei der die Konjugation durch eine radikalische Additionsreaktion von als Allylamide funktionalisierten Glycopeptiden an ein Thiol-modifiziertes Trägerprotein erfolgte. Dazu wurde anhand von synthetisierten, als Allylamide modifizierten Modellaminosäuren untersucht, ob diese Reaktion generell für eine Biokonjugation geeignet ist und etwaige Nebenreaktionen auftreten können. Mit dieser Methode konnten verschiedene MUC1-Glycopeptid-Trägerprotein-Konjugate hergestellt werden, deren immunologische Untersuchung noch bevorsteht. Das tumorassoziierte MUC1 nimmt in der immundominanten Region seiner Wiederholungseinheit eine knaufartige Struktur ein. Für die Entwicklung von selektiven Tumorvakzinen ist es von großer Bedeutung möglichst genau die Struktur der veränderten Zelloberflächenmoleküle nachzubilden. Durch die Synthese von cyclischen (Glyco)Peptiden wurde dieses Strukturelement fixiert. Dazu wurden olefinische Aminosäure Festphasenbausteine hergestellt, die zusammen mit den oben genannten Glycosylaminosäuren mittels einer Glycopeptid-Festphasensynthese in acyclische Glycopeptide eingebaut wurden. Diese wurden dann durch Ringschlussmetathese zyklisiert und im Anschluss reduziert und vollständig deblockiert. In einem dritten Projekt wurde der Syntheseweg zur Herstellung einer C-Glycosylaminosäure mit einer N-Acetylgalactosamin-Einheit entwickelt. Wichtige Schritte bei der von Glucosamin ausgehenden Synthese sind die Keck-Allylierung, eine Epimerisierung, die Herstellung eines Brom-Dehydroalanin-Derivates und eine B-Alkyl-Suzuki-Miyaura-Kreuzkupplung sowie Schutzgruppenoperationen. Der racemische Baustein konnte dann in der Peptid-Festphasensynthese eines komplexen MUC1-Tetanustoxin-Konjugates eingesetzt werden.

Comportamento tribologico di materiali per componenti di interesse industriale: Failure analysis e prove tribologiche in laboratorio

L’attività di ricerca della presente tesi di dottorato ha riguardato sistemi tribologici complessi di interesse industriale per i quali sono stati individuati, mediante failure analysis, i meccanismi di usura dominanti. Per ciascuno di essi sono state studiate soluzioni migliorative sulla base di prove tribologiche di laboratorio. Nella realizzazione di maglie per macchine movimentazione terra sono ampiamente utilizzati i tradizionali acciai da bonifica. La possibilità di utilizzare i nuovi microlegati a medio tenore di carbonio, consentirebbe una notevole semplificazione del ciclo produttivo e benefici in termini di costi. Una parte della tesi ha riguardato lo studio del comportamento tribologico di tali acciai. E’ stato anche affrontato lo studio tribologico di motori idraulici, con l’obiettivo di riuscire a migliorarne la resistenza ad usura e quindi la vita utile. Sono state eseguite prove a banco, per valutare i principali meccanismi di usura, e prove di laboratorio atte a riprodurre le reali condizioni di utilizzo, valutando tecniche di modificazione superficiale che fossero in grado di ridurre l’usura dei componenti. Sono state analizzate diverse tipologie di rivestimenti Thermal Spray in termini di modalità di deposizione (AFS-APS) e di leghe metalliche depositate (Ni,Mo,Cu/Al). Si sono infine caratterizzati contatti tribologici nel settore del packaging, dove l’utilizzo di acciai inox austenitici è in alcuni casi obbligatorio. L’acciaio inossidabile AISI 316L è ampiamente utilizzato in applicazioni in cui siano richieste elevate resistenze alla corrosione, tuttavia la bassa resistenza all’usura, ne limitano l’impiego in campo tribologico. In tale ambito, è stata analizzata una problematica tribologica relativa a macchine automatiche per il dosaggio di polveri farmaceutiche. Sono state studiate soluzioni alternative che hanno previsto sia la completa sostituzione dei materiali della coppia tribologica, sia l’individuazione di tecniche di modificazione superficiale innovative quali la cementazione a bassa temperatura anche seguita dalla deposizione di un rivestimento di carbonio amorfo idrogenato a-C:H

Atomic-scale characterization of diamond surfaces and fullerene self-assembly

In this thesis, elemental research towards the implantation of a diamond-based molecular quantum computer is presented. The approach followed requires linear alignment of endohedral fullerenes on the diamond C(100) surface in the vicinity of subsurface NV-centers. From this, four fundamental experimental challenges arise: 1) The well-controlled deposition of endohedral fullerenes on a diamond surface. 2) The creation of NV-centers in diamond close to the surface. 3) Preparation and characterization of atomically-flat diamondsurfaces. 4) Assembly of linear chains of endohedral fullerenes. First steps to overcome all these challenges were taken in the framework of this thesis. Therefore, a so-called “pulse injection” technique was implemented and tested in a UHV chamber that was custom-designed for this and further tasks. Pulse injection in principle allows for the deposition of molecules from solution onto a substrate and can therefore be used to deposit molecular species that are not stable to sublimation under UHV conditions, such as the endohedral fullerenes needed for a quantum register. Regarding the targeted creation of NV-centers, FIB experiments were carried out in cooperation with the group of Prof. Schmidt-Kaler (AG Quantum, Physics Department, Johannes Gutenberg-Universität Mainz). As an entry into this challenging task, argon cations were implanted into (111) surface-oriented CaF2 crystals. The resulting implantation spots on the surface were imaged and characterized using AFM. In this context, general relations between the impact of the ions on the surface and their valency or kinetic energy, respectively, could be established. The main part of this thesis, however, is constituted by NCAFM studies on both, bare and hydrogen-terminated diamond C(100) surfaces. In cooperation with the group of Prof. Dujardin (Molecular Nanoscience Group, ISMO, Université de Paris XI), clean and atomically-flat diamond surfaces were prepared by exposure of the substrate to a microwave hydrogen plasma. Subsequently, both surface modifications were imaged in high resolution with NC-AFM. In the process, both hydrogen atoms in the unit cell of the hydrogenated surface were resolved individually, which was not achieved in previous STM studies of this surface. The NC-AFM images also reveal, for the first time, atomic-resolution contrast on the clean, insulating diamond surface and provide real-space experimental evidence for a (2×1) surface reconstruction. With regard to the quantum computing concept, high-resolution NC-AFM imaging was also used to study the adsorption and self-assembly potential of two different kinds of fullerenes (C60 and C60F48) on aforementioned diamond surfaces. In case of the hydrogenated surface, particular attention was paid to the influence of charge transfer doping on the fullerene-substrate interaction and the morphology emerging from self-assembly. Finally, self-assembled C60 islands on the hydrogen-terminated diamond surface were subject to active manipulation by an NC-AFM tip. Two different kinds of tip-induced island growth modes have been induced and were presented. In conclusion, the results obtained provide fundamental informations mandatory for the realization of a molecular quantum computer. In the process it was shown that NC-AFM is, under proper circumstances, a very capable tool for imaging diamond surfaces with highest resolution, surpassing even what has been achieved with STM up to now. Particular attention was paid to the influence of transfer doping on the morphology of fullerenes on the hydrogenated diamond surface, revealing new possibilities for tailoring the self-assembly of molecules that have a high electron affinity.

Enantioselective synthesis of Equol with Ir-BARF and labelling with deuterium

In this project we researched and optimized an new synthetic route for R-Equol, a molecule that is attracting increasing interest for the medicine because of its phytoestrogenic properties and the chemoprevention of breast cancer. To reach this objective we start, from smaller building blocks, with the synthesis of Daidzein followed by a chemoselective borane reduction to obtain an olefin that will be hydrogenated enantioselectively with a commercial Ir-BARF catalyst. The increasing success of these catalysts even with this genre of substrates has already given good results with different catalysts in both e.e. and yield. For further researches we deuterate the Equol in the aliphatic O-ring and attempt a secondary synthetic route with an hydrogenation using QN-modified Pd.

Cardiovascular regulation during administration of co-dergocrine to normal subjects

Whether and to what extent activation of peripheral presynaptic dopamine2-receptors may modulate the release of norepinephrine (NE) and so affect blood pressure (BP) in normal or hypertensive man is not clear. The hydrogenated ergotoxine derivative, co-dergocrine, given in effective antihypertensive rather than excessive experimental doses, has recently been shown to act predominantly as a peripheral dopamine2-receptor agonist in several species. Accordingly, BP regulation assessed has been in 8 normal men on placebo and after 3 weeks on codergocrine 4 mg/day. Co-dergocrine significantly reduced urinary NE excretion from 43 to 33 micrograms/24 h, supine and upright plasma NE 21 to 16 and 49 to 36 ng/dl, respectively, heart rate (-8 and -5%, respectively) and upright systolic BP, 115 to 102 mm Hg; upright diastolic BP also tended to be lower. A standard pressor dose of infused NE was lowered from 131 to 102 ng/kg/min, and the relationship between NE-induced changes in BP and concomitant NE infusion rate or plasma NE concentration was displaced to the left. Exchangeable sodium and plasma volume tended to be slightly decreased. Plasma and urinary electrolytes and epinephrine, plasma renin activity and aldosterone levels, pressor responsiveness to angiotensin II, the chronotropic responses to isoproterenol, and the NE-induced rise in BP, plasma clearance of NE, glomerular filtration rate and effective renal plasma flow were not consistently modified. The findings are consistent with effective peripheral dopamine2-receptor agonism by co-dergocrine in humans. Peripheral presynaptic dopaminergic activation may modulate sympathetic activity and BP in normal man.

Novel sst5-selective somatostatin dicarba-analogues: synthesis and conformation-affinity relationships

We describe synthesis, conformational studies, and binding to the five somatostatin receptors (sst 1-5) of a few analogues of the cyclic octapeptide octreotide (1), where the disulfide bridge was replaced by a dicarba group. These analogues were prepared by on-resin RCM of linear hepta-peptides containing two allylglycine residues; first- and second-generation Grubbs catalyst efficiencies were compared. The C=C bridge was hydrogenated via two different methods. Binding experiments showed that two analogues had good affinity and high selectivity for the sst5 receptor. Three-dimensional structures of the active analogues were determined by (1)H NMR spectroscopy. Conformation-affinity relationships confirmed the importance of D-Phe(2) orientation for sst2 affinity. Moreover, helical propensities well correlates with the peptide sst5 affinity. The presence of the bulky aromatic side chain of Tyr(Bzl)(10) favored the formation of a 3(10)-helix and enhanced the sst5 selectivity suppressing the sst2 affinity. Finally, a new pharmacophore model for the sst5 was developed.

THE USE OF LIFE-CYCLE ANALYSIS TO REDUCE THE ENVIRONMENTAL IMPACT OF MATERIALS IN MANUFACTURING

This thesis is composed of three life-cycle analysis (LCA) studies of manufacturing to determine cumulative energy demand (CED) and greenhouse gas emissions (GHG). The methods proposed could reduce the environmental impact by reducing the CED in three manufacturing processes. First, industrial symbiosis is proposed and a LCA is performed on both conventional 1 GW-scaled hydrogenated amorphous silicon (a-Si:H)-based single junction and a-Si:H/microcrystalline-Si:H tandem cell solar PV manufacturing plants and such plants coupled to silane recycling plants. Using a recycling process that results in a silane loss of only 17 versus 85 percent, this results in a CED savings of 81,700 GJ and 290,000 GJ per year for single and tandem junction plants, respectively. This recycling process reduces the cost of raw silane by 68 percent, or approximately $22.6 and $79 million per year for a single and tandem 1 GW PV production facility, respectively. The results show environmental benefits of silane recycling centered around a-Si:H-based PV manufacturing plants. Second, an open-source self-replicating rapid prototype or 3-D printer, the RepRap, has the potential to reduce the environmental impact of manufacturing of polymer-based products, using distributed manufacturing paradigm, which is further minimized by the use of PV and improvements in PV manufacturing. Using 3-D printers for manufacturing provides the ability to ultra-customize products and to change fill composition, which increases material efficiency. An LCA was performed on three polymer-based products to determine the CED and GHG from conventional large-scale production and are compared to experimental measurements on a RepRap producing identical products with ABS and PLA. The results of this LCA study indicate that the CED of manufacturing polymer products can possibly be reduced using distributed manufacturing with existing 3-D printers under 89% fill and reduced even further with a solar photovoltaic system. The results indicate that the ability of RepRaps to vary fill has the potential to diminish environmental impact on many products. Third, one additional way to improve the environmental performance of this distributed manufacturing system is to create the polymer filament feedstock for 3-D printers using post-consumer plastic bottles. An LCA was performed on the recycling of high density polyethylene (HDPE) using the RecycleBot. The results of the LCA showed that distributed recycling has a lower CED than the best-case scenario used for centralized recycling. If this process is applied to the HDPE currently recycled in the U.S., more than 100 million MJ of energy could be conserved per annum along with significant reductions in GHG. This presents a novel path to a future of distributed manufacturing suited for both the developed and developing world with reduced environmental impact. From improving manufacturing in the photovoltaic industry with the use of recycling to recycling and manufacturing plastic products within our own homes, each step reduces the impact on the environment. The three coupled projects presented here show a clear potential to reduce the environmental impact of manufacturing and other processes by implementing complimenting systems, which have environmental benefits of their own in order to achieve a compounding effect of reduced CED and GHG.

Comportamiento del perfil de ácidos grasos de aceites y materias grasas hidrogenadas sometidos a calentamiento prolongado

La fritura es un proceso altamente utilizado a nivel industrial y casero, el que considera someter a las grasas a temperaturas cercanas a los 200°C, con lo cual se producen complicados cambios físicos y químicos. En Chile, se utilizan para freír mantecas hidrogenadas las cuales han mostrado alto contenido en ácidos grasos trans (AGT). Este trabajo tiene como objetivo determinar los cambios en el perfil en ácidos grasos, con énfasis en AGT, de diferentes tipos de materias grasas hidrogenadas y aceites vegetales sometidos a calentamiento. Para esto se evaluó y se sometió a un ciclo de calentamiento por 50 h 7 diferentes tipos de materias grasas y como control se consideró a aceite de girasol, se evaluaron los tiempos 0, 10, 20, 30, 40 y 50 h. La composición en ácidos grasos se realizó por cromatografía gas - liquido previa preparación de los ésteres metílicos según Norma española, UNE-EN ISO 5509. Los resultados mostraron que la composición en ácidos grasos de todas las materias grasas estudiadas presentaron modificación durante el tratamiento térmico, observándose una disminución de los ácidos grasos poliinsaturados y un aumento o preservación de los ácidos grasos monoinsaturados y saturados. Los ácidos grasos trans mostraron contenidos importantes en mantecas hidrogenadas (20%), los que se mantuvieron constantes durante todo el calentamiento. El aceite de girasol y el de girasol alto oleico resultaron ser los más adecuados para freír, ya que no mostraron presencia de AGT y se mantuvieron aptos para ser utilizados hasta las 40 h de calentamiento.

Optimization of laser-firing processes for silicon-heterojunction solar-cell back contacts

One of the key steps to achieve high efficiencies in amorphous/crystalline silicon photovoltaic structures is to design low-ohmic-resistance backcontacts with good passivation in the rear part of the cell. A well known approach to achieve this goal is to use laser-fired contact (LFC) processes in which a metal layer is fired through the dielectric to define good contacts with the semiconductor. However, and despite the fact that this approach has demonstrated to be extremely successful, there is still enough room for process improvement with an appropriate optimization. In this paper, a study focused on the optimal adjustment of the irradiation parameters to produce laser-fired contacts in a-Si:H/c-Si heterojunctionsolarcells is presented. We used samples consisting of crystalline-silicon (c-Si) wafers together with a passivation layer of intrinsic hydrogenated amorphous silicon (a-Si:H(i)) deposited by plasma-enhanced chemical deposition (PECVD). Then, an aluminum layer was evaporated on both sides, the thickness of this layer varied from 0.2 to 1 μm in order to identify the optimal amount of Al required to create an appropriate contact. A q-switched Nd:YVO4laser source, λ = 532 nm, was used to locally fire the aluminum through the thin a-Si:H(i)-layers to form the LFC. The effects of laser fluences were analyzed using a comprehensive morphological and electrical characterization.

The intermediate band approach in the third solar cell generation context

Hydrogenated amorphous silicon thin films were deposited using a high pressure sputtering (HPS) system. In this work, we have studied the composition and optical properties of the films (band-gap, absorption coefficient), and their dependence with the deposition parameters. For films deposited at high pressure (1 mbar), composition measurements show a critical dependence of the purity of the films with the RF power. Films manufactured with RF-power above 80W exhibit good properties for future application, similar to the films deposited by CVD (Chemical Vapor Deposition) for hydrogenated amorphous silicon.

Animal performance and meat characteristics in steers reared in intensive conditions fed with different vegetable oils

Enhancing the quality of beef meat is an important goal in terms of improving both the nutritional value for the consumer and the commercial value for producers. The aim of this work was to study the effects of different vegetable oil supplements on growth performance, carcass quality and meat quality in beef steers reared under intensive conditions. A total of 240 Blonde D? Aquitaine steers (average BW = 293.7 ± 38.88 kg) were grouped into 24 batches (10 steers/batch) and were randomly assigned to one of the three dietary treatments (eight batches per treatment), each supplemented with either 4% hydrogenated palm oil (PALM) or fatty acids (FAs) from olive oil (OLI) or soybean oil (SOY). No differences in growth performance or carcass quality were observed. For the meat quality analysis, a steer was randomly selected from each batch and the 6th rib on the left half of the carcass was dissected. PALM meat had the highest percentage of 16:0 ( P< 0.05) and the lowest n-6/n-3 polyunsaturated fatty acids (PUFA) ratio ( P< 0.05), OLI had the highest content of t 11-18:1 ( P< 0.01) and c 9,t 11-18:2 ( P< 0.05) and SOY showed the lowest value of monounsaturated fatty acids (MUFA) ( P< 0.001), the highest percentage of PUFA ( P< 0.01) and a lower index of atherogenicity ( P = 0.07) than PALM. No significant differences in the sensory characteristics of the meat were noted. However, the results of the principal component analysis of meat characteristics enabled meat from those steers that consumed fatty acids from olive oil to be differentiated from that of steers that consumed soybean oil.

Brassinosteroid/Sterol Synthesis and Plant Growth as Affected by lka and lkb Mutations of Pea1

The dwarf pea (Pisum sativum) mutants lka and lkb are brassinosteroid (BR) insensitive and deficient, respectively. The dwarf phenotype of the lkb mutant was rescued to wild type by exogenous application of brassinolide and its biosynthetic precursors. Gas chromatography-mass spectrometry analysis of the endogenous sterols in this mutant revealed that it accumulates 24-methylenecholesterol and isofucosterol but is deficient in their hydrogenated products, campesterol and sitosterol. Feeding experiments using 2H-labeled 24-methylenecholesterol indicated that the lkb mutant is unable to isomerize and/or reduce the Δ24(28) double bond. Dwarfism of the lkb mutant is, therefore, due to BR deficiency caused by blocked synthesis of campesterol from 24-methylenecholesterol. The lkb mutation also disrupted sterol composition of the membranes, which, in contrast to those of the wild type, contained isofucosterol as the major sterol and lacked stigmasterol. The lka mutant was not BR deficient, because it accumulated castasterone. Like some gibberellin-insensitive dwarf mutants, overproduction of castasterone in the lka mutant may be ascribed to the lack of a feedback control mechanism due to impaired perception/signal transduction of BRs. The possibility that castasterone is a biologically active BR is discussed.

Estudo da seletividade de catalisadores a base de cobre e paládio em transformações de hidrocarbonetos insaturados

Compreender a correlação entre as características de um catalisador particular e seu desempenho catalítico tem sido um dos principais objetos da pesquisa em catálise heterogênea a fim de usar esse conhecimento para o desenho racional de catalisadores mais ativos, seletivos e estáveis. A seletividade é um dos fatores mais importantes a ser controlado pelo desenho de catalisadores, podendo ser alcançada de diversas maneiras, levando-se em consideração mudanças do tipo estrutural, química, eletrônica, de composição, de cinética e de energia. O trabalho descrito nessa tese de doutorado compreende a síntese e caracterização de catalisadores compostos de nanopartículas de óxido de cobre, paládio e cobre-paládio e seu estudo em reações de hidrogenação e oxidação seletivas de hidrocarbonetos insaturados. Os catalisadores foram preparados através da deposição de nanopartículas dos metais cataliticamente ativos sobre suportes magneticamente recuperáveis compostos de nanopartículas de magnetita revestidas por sílica com superfícies funcionalizada com diferentes grupos orgânicos. A natureza magnética do suporte permitiu a fácil separação do catalisador do meio reacional pela simples aproximação de um ímã na parede do reator. O catalisador pôde ser completamente separado da fase líquida, fazendo com que a utilização de outros métodos de separação como filtração e centrifugação, comumente utilizados em sistemas heterogêneos líquidos, fossem completamente dispensados. Os catalisadores foram inicialmente testados em reações de hidrogenação de alquenos e alquinos. As reações de hidrogenação foram realizadas utilizando hidrogênio molecular como agente redutor, dispensando a utilização de agentes redutores mais agressivos. Os catalisadores compostos de NPs de Pd mostram excelente atividade e capacidade de reutilização na hidrogenação de cicloexeno, podendo ser utilizados em até 15 ciclos sem perda de atividade. Nas reações de hidrogenação de alquinos, os catalisadores que contêm cobre mostraram maior seletividade para a obtenção dos produtos de semi-hidrogenação, com destaque para o catalisador composto de NPs de CuPd, que não apresenta nem traços do produto de hidrogenação completa na amostra final. Esse catalisador bimetálico alia as características do paládio (elevada atividade) e do cobre (elevada seletividade) para fornecer um catalisador ativo e seletivo para a transformação desejada. Além disso, os grupos funcionais presentes na superfície do suporte catalítico mostraram influência na atividade e seletividade para a hidrogenação de alquenos e alquinos. Os catalisadores sintetizados também foram testados na reação de oxidação de cicloexeno e mostraram seletividade para a produção do composto carbonílico α,β-insaturado, cicloex-2-en-1-ona, que é um reagente de partida de grande interesse para a síntese de diversos materiais na indústria química. As reações de oxidação foram realizadas utilizando-se apenas O2 como oxidante primário, dispensando o uso de oxidantes tóxicos como cromatos, permanganatos ou compostos halogenados, que não são recomendados do ponto de vista ambiental. Os catalisadores sintetizados puderam ser reutilizados em sucessivos ciclos de oxidação, mostrando seletividade para a formação dos produtos alílicos em todos os ciclos. Os catalisadores foram estáveis sob as condições reacionais e não apresentaram problemas de lixiviação da espécie ativa para o meio reacional, que é comum na catálise heterogênea. Um estudo cinético mostrou que, mesmo no início da reação, o catalisador tem seletividade para a ocorrência de oxidação alílica em detrimento da reação de oxidação direta que dá origem ao epóxidos correspondente, e se mostrou condizente com o mecanismo proposto na literatura para a reação de oxidação de alquenos via radicalar.