Why adopt now? Multiple case studies and survey studies comparing small, medium and large firms

While a number of factors have been highlighted in the innovation adoption literature, little is known about whether different factors are related to innovation adoption in differently-sized firms. We used preliminary case studies of small, medium and large firms to ground our hypotheses, which were then tested using a survey of 94 firms. We found that external stakeholder pressure and non-financial readiness were related to innovation adoption in SMEs; but that for large firms, adoption was related to the opportunity to innovate. It may be that the difficulties of adopting innovations, including both the financial cost and the effort involved, are too great for SMEs to overcome unless there is either a compelling need (external pressure) or enough in-house capability (non-financial readiness). This suggests that SMEs are more likely to have innovation “pushed” onto them while large firms are more likely to “pull” innovations when they have the opportunity.

A study on acoustic emission signal propagation of a small size multi-cylinder diesel engine

Acoustic emission has been found effective in offering earlier fault detection and improving identification capabilities of faults. However, the sensors are inherently uncalibrated. This paper presents a source to sensor paths calibration technique which can lead to diagnosis of faults in a small size multi-cylinder diesel engine. Preliminary analysis of the acoustic emission (AE) signals is outlined, including time domain, time-frequency domain, and the root mean square (RMS) energy. The results reveal how the RMS energy of a source propagates to the adjacent sensors. The findings lead to allocate the source and estimate its inferences to the adjacent sensor, and finally help to diagnose the small size diesel engines by minimising the crosstalk from multiple cylinders.

Knowledge management for enterprise systems: observations from small, medium and large organizations

Anecdotal evidence suggests that the lifecycle-wide management of Enterprise System (ES) related knowledge is critical for ES health and longevity. At a time where many ES-vendors now offering solutions to Small and Medium size organizations, this paper investigates the ability of Small and Medium size organizations to maintain a lifecycle-wide knowledge management strategy. The paper explores the alleged differences in the knowledge management practices across 27 small, medium and large organizations that had implemented a market-leading ES. Results suggest that: (1) despite similar knowledge creation efforts in all three organizational sizes, small organizations struggle with retaining, transferring and applying the knowledge. The study also reveals that, (2) the overall goodness of the knowledge management process in larger organizations remains higher than their small and medium counterparts.

Introducing a small and medium enterprises syllabi design: an enterprise systems hands-on approach

There is increasing attention to the importance of Enterprise Systems (ES) and Information Systems (IS) for Small and Medium Enterprises (SMEs). The same attention must be addressed in IS graduate curriculum. Studies reveal that despite healthy demand from the industry for IS management expertise, most IS graduates are ill-equipped to meet the challenges of modern organizations. The majority of contemporary firms, represented by SMEs, seek employees with a balance of business process knowledge and ES software skills. This article describes a curriculum that teaches Information Technology (IT) and IS managementconcepts in a SMEs context. The curriculum conceptualises a ‘learn-by-doing’ approach, to provide business process and ES software specific knowledge for its students. The approach recommends coverage of traditional content related to SMEs’’ operations, strategies, IT investment and management issues while providing an increased focus on strategic use of enterprise IT. The study addresses to an extent, the perennial challenge of updating IS curriculum, given the rapid pace of technological change.

Small animal bone healing models : standards, tips, and pitfalls results of a consensus meeting

Small animal fracture models have gained increasing interest in fracture healing studies. To achieve standardized and defined study conditions, various variables must be carefully controlled when designing fracture healing experiments in mice or rats. The strain, age and sex of the animals may influence the process of fracture healing. Furthermore, the choice of the fracture fixation technique depends on the questions addressed, whereby intra- and extramedullary implants as well as open and closed surgical approaches may be considered. During the last few years, a variety of different, highly sophisticated implants for fracture fixation in small animals have been developed. Rigid fixation with locking plates or external fixators results in predominantly intramembranous healing in both mice and rats. Locking plates, external fixators, intramedullary screws, the locking nail and the pin-clip device allow different degrees of stability resulting in various amounts of endochondral and intramembranous healing. The use of common pins that do not provide rotational and axial stability during fracture stabilization should be discouraged in the future. Analyses should include at least biomechanical and histological evaluations, even if the focus of the study is directed towards the elucidation of molecular mechanisms of fracture healing using the largely available spectrum of antibodies and gene-targeted animals to study molecular mechanisms of fracture healing. This review discusses distinct requirements for the experimental setups as well as the advantages and pitfalls of the different fixation techniques in rats and mice.

Forgotten places : rediscovering the small spaces and laneways of Fortitude Valley

A design Charrette was the starting point for understanding the different scales within the design process of this architectural intervention. The week-long, intense design activity promoted group interaction amongst students while examining local issues of the Fortitude Valley context. The process was an opportunity for the fourth year architectural design students to collaborate on a complex design problem. Students were asked to identify a unique condition of their site beyond the physical built environment. They were asked to consider the political and social context and respond to these by designing a temporary art gallery for underdeveloped areas within Fortitude Valley. The exhibition shows how architecture can invigorate a space by providing new use and new life.

Omnidirectional bearing-only see-and-avoid for small aerial robots

Motivated by the growing interest in unmanned aerial system’s applications in indoor and outdoor settings and the standardisation of visual sensors as vehicle payload. This work presents a collision avoidance approach based on omnidirectional cameras that does not require the estimation of range between two platforms to resolve a collision encounter. It will achieve a minimum separation between the two vehicles involved by maximising the view-angle given by the omnidirectional sensor. Only visual information is used to achieve avoidance under a bearing-only visual servoing approach. We provide theoretical problem formulation, as well as results from real flight using small quadrotors.

A model of organizational innovation implementation effectiveness in small to medium firms

The present study aims to validate the current best-practice model of implementation effectiveness in small and mid-size businesses. Data from 135 organizations largely confirm the original model across various types of innovation. In addition, we extended this work by highlighting the importance of human resources in implementation effectiveness and the consequences of innovation effectiveness on future adoption attitudes. We found that the availability of skilled employees was positively related to implementation effectiveness. Furthermore, organizations that perceived a high level of benefits from implemented innovations were likely to have a positive attitude towards future innovation adoption. The implications of our improvements to the original model of implementation effectiveness are discussed.

The iPhone Moment, the Apple Brand and the creative consumer : From “hackability and usability” to cultural generativity

In this chapter I position the iPhone as a “moment” in the history of cultural technologies. Drawing predominantly on advertising materials and public conversations about other "moments" in the history of personal computing and focusing on Apple’s role in this history, I argue that the design philosophy, marketing, and business models behind the iPhone (and now the iPad) have decisively reframed the values of usability that underpin software and interface design in the consumer technology industry, marking a distinctive shift in the history and contested futures of digital culture.

Turbulent measurements in a small subtropical estuary with semidiurnal tides

Since predictions of scalar dispersion in small estuaries can rarely be predicted accurately, new field measurements were conducted continuously at relatively high frequency for up to 50 h (per investigation) in a small subtropical estuary with semidiurnal tides. The bulk flow parameters varied in time with periods comparable to tidal cycles and other large-scale processes. The turbulence properties depended upon the instantaneous local flow properties. They were little affected by the flow history, but their structure and temporal variability were influenced by a variety of parameters including the tidal conditions and bathymetry. A striking feature of the data sets was the large fluctuations in all turbulence characteristics during the tidal cycle, and basic differences between neap and spring tide turbulence.

Physical characteristics of small ions and their interaction with ultrafine particles in the urban environment

In recent years, the effect of ions and ultrafine particles on ambient air quality and human health has been well documented, however, knowledge about their sources, concentrations and interactions within different types of urban environments remains limited. This thesis presents the results of numerous field studies aimed at quantifying variations in ion concentration with distance from the source, as well as identifying the dynamics of the particle ionisation processes which lead to the formation of charged particles in the air. In order to select the most appropriate measurement instruments and locations for the studies, a literature review was also conducted on studies that reported ion and ultrafine particle emissions from different sources in a typical urban environment. The initial study involved laboratory experiments on the attachment of ions to aerosols, so as to gain a better understanding of the interaction between ions and particles. This study determined the efficiency of corona ions at charging and removing particles from the air, as a function of different particle number and ion concentrations. The results showed that particle number loss was directly proportional to particle charge concentration, and that higher small ion concentrations led to higher particle deposition rates in all size ranges investigated. Nanoparticles were also observed to decrease with increasing particle charge concentration, due to their higher Brownian mobility and subsequent attachment to charged particles. Given that corona discharge from high voltage powerlines is considered one of the major ion sources in urban areas, a detailed study was then conducted under three parallel overhead powerlines, with a steady wind blowing in a perpendicular direction to the lines. The results showed that large sections of the lines did not produce any corona at all, while strong positive emissions were observed from discrete components such as a particular set of spacers on one of the lines. Measurements were also conducted at eight upwind and downwind points perpendicular to the powerlines, spanning a total distance of about 160m. The maximum positive small and large ion concentrations, and DC electric field were observed at a point 20 m downwind from the lines, with median values of 4.4×103 cm-3, 1.3×103 cm-3 and 530 V m-1, respectively. It was estimated that, at this point, less than 7% of the total number of particles was charged. The electrical parameters decreased steadily with increasing downwind distance from the lines but remained significantly higher than background levels at the limit of the measurements. Moreover, vehicles are one of the most prevalent ion and particle emitting sources in urban environments, and therefore, experiments were also conducted behind a motor vehicle exhaust pipe and near busy motorways, with the aim of quantifying small ion and particle charge concentration, as well as their distribution as a function of distance from the source. The study found that approximately equal numbers of positive and negative ions were observed in the vehicle exhaust plume, as well as near motorways, of which heavy duty vehicles were believed to be the main contributor. In addition, cluster ion concentration was observed to decrease rapidly within the first 10-15 m from the road and ion-ion recombination and ion-aerosol attachment were the most likely cause of ion depletion, rather than dilution and turbulence related processes. In addition to the above-mentioned dominant ion sources, other sources also exist within urban environments where intensive human activities take place. In this part of the study, airborne concentrations of small ions, particles and net particle charge were measured at 32 different outdoor sites in and around Brisbane, Australia, which were classified into seven different groups as follows: park, woodland, city centre, residential, freeway, powerlines and power substation. Whilst the study confirmed that powerlines, power substations and freeways were the main ion sources in an urban environment, it also suggested that not all powerlines emitted ions, only those with discrete corona discharge points. In addition to the main ion sources, higher ion concentrations were also observed environments affected by vehicle traffic and human activities, such as the city centre and residential areas. A considerable number of ions were also observed in a woodland area and it is still unclear if they were emitted directly from the trees, or if they originated from some other local source. Overall, it was found that different types of environments had different types of ion sources, which could be classified as unipolar or bipolar particle sources, as well as ion sources that co-exist with particle sources. In general, fewer small ions were observed at sites with co-existing sources, however particle charge was often higher due to the effect of ion-particle attachment. In summary, this study quantified ion concentrations in typical urban environments, identified major charge sources in urban areas, and determined the spatial dispersion of ions as a function of distance from the source, as well as their controlling factors. The study also presented ion-aerosol attachment efficiencies under high ion concentration conditions, both in the laboratory and in real outdoor environments. The outcomes of these studies addressed the aims of this work and advanced understanding of the charge status of aerosols in the urban environment.

Jams, jelly beans and the fruits of passion - art book (26 Pages)

Statement: Jams, Jelly Beans and the Fruits of Passion Let us search, instead, for an epistemology of practice implicit in the artistic, intuitive processes which some practitioners do bring to situations of uncertainty, instability, uniqueness, and value conflict. (Schön 1983, p40) Game On was born out of the idea of creative community; finding, networking, supporting and inspiring the people behind the face of an industry, those in the mist of the machine and those intending to join. We understood this moment to be a pivotal opportunity to nurture a new emerging form of game making, in an era of change, where the old industry models were proving to be unsustainable. As soon as we started putting people into a room under pressure, to make something in 48hrs, a whole pile of evolutionary creative responses emerged. People refashioned their craft in a moment of intense creativity that demanded different ways of working, an adaptive approach to the craft of making games – small – fast – indie. An event like the 48hrs forces participants’ attention onto the process as much as the outcome. As one game industry professional taking part in a challenge for the first time observed: there are three paths in the genesis from idea to finished work: the path that focuses on mechanics; the path that focuses on team structure and roles, and the path that focuses on the idea, the spirit – and the more successful teams put the spirit of the work first and foremost. The spirit drives the adaptation, it becomes improvisation. As Schön says: “Improvisation consists on varying, combining and recombining a set of figures within the schema which bounds and gives coherence to the performance.” (1983, p55). This improvisational approach is all about those making the games: the people and the principles of their creative process. This documentation evidences the intensity of their passion, determination and the shit that they are prepared to put themselves through to achieve their goal – to win a cup full of jellybeans and make a working game in 48hrs. 48hr is a project where, on all levels, analogue meets digital. This concept was further explored through the documentation process. All of these pictures were taken with a 1945 Leica III camera. The use of this classic, film-based camera, gives the images a granularity and depth, this older slower technology exposes the very human moments of digital creativity. ____________________________ Schön, D. A. 1983, The Reflective Practitioner: How Professionals Think in Action, Basic Books, New York

Identifying parent perspectives to guide active travel intervention with small populations : case study in Denver, Colorado

This paper investigates a strategy for guiding school-based active travel intervention. School-based active travel programs address the travel behaviors and perceptions of small target populations (i.e., at individual schools) so they can encourage people to walk or bike. Thus, planners need to know as much as possible about the behaviors and perceptions of their target populations. However, existing strategies for modeling travel behavior and segmenting audiences typically work with larger populations and may not capture the attitudinal diversity of smaller groups. This case study used Q technique to identify salient travel-related attitude types among parents at an elementary school in Denver, Colorado; 161 parents presented their perspectives about school travel by rank-ordering 36 statements from strongly disagree to strongly agree in a normalized distribution, single centered around no opinion. Thirty-nine respondents' cases were selected for case-wise cluster analysis in SPSS according to criteria that made them most likely to walk: proximity to school, grade, and bus service. Analysis revealed five core perspectives that were then correlated with the larger respondent pool: optimistic walkers, fair-weather walkers, drivers of necessity, determined drivers, and fence sitters. Core perspectives are presented—characterized by parents' opinions, personal characteristics, and reported travel behaviors—and recommendations are made for possible intervention approaches. The study concludes that Q technique provides a fine-grained assessment of travel behavior for small populations, which would benefit small-scale behavioral interventions

Unintended consequences of regulatory reporting requirements for small and medium size construction entities : Australian evidence

The Queensland Building Services Authority (QBSA) regulates the construction industry in Queensland, Australia, with licensing requirements creating differential financial reporting obligations, depending on firm size. Economic theories of regulation and behaviour provide a framework for investigating effects of the financial constraints and financial reporting requirements imposed by QBSA licensing. Data are analysed for all small and medium construction entities operating in Queensland between 2001 and 2006. Findings suggesting that construction licensees are categorizing themselves as smaller to avoid the more onerous and costly financial reporting of higher licensee categories are consistent with US findings from the 2002 Sarbanes-Oxley (SOX) regulation which created incentives for small firms to stay small to avoid the costs of compliance with more onerous financial reporting requirements. Such behaviour can have the undesirable economic consequences of adversely affecting employment, investment, wealth creation and financial stability. Insights and implications from the analysed QBSA processes are important for future policy reform and design, and useful to be considered where similar regulatory approaches are planned.

Power relations and small and medium-sized enterprise strategies for capturing value in global production networks: visual effects (VFX) service firm in the Hollywood film industry

Power relations and small and medium-sized enterprise strategies for capturing value in global production networks: visual effects (VFX) service firms in the Hollywood film industry, Regional Studies. This paper provides insights into the way in which non-lead firms manoeuvre in global value chains in the pursuit of a larger share of revenue and how power relations affect these manoeuvres. It examines the nature of value capture and power relations in the global supply of visual effects (VFX) services and the range of strategies VFX firms adopt to capture higher value in the global value chain. The analysis is based on a total of thirty-six interviews with informants in the industry in Australia, the United Kingdom and Canada, and a database of VFX credits for 3323 visual products for 640 VFX firms.