Relating vehicle generated pollutants to urban stormwater quality

Rapid urbanisation and resulting continuous increase in traffic has been recognised as key factors in the contribution of increased pollutant loads to urban stormwater and in turn to receiving waters. Urbanisation primarily increases anthropogenic activities and the percentage of impervious surfaces in urban areas. These processes are collectively responsible for urban stormwater pollution. In this regard, urban traffic and land use related activities have been recognised as the primary pollutant sources. This is primarily due to the generation of a range of key pollutants such as solids, heavy metals and PAHs. Appropriate treatment system design is the most viable approach to mitigate stormwater pollution. However, limited understanding of the pollutant process and transport pathways constrains effective treatment design. This highlights necessity for the detailed understanding of traffic and other land use related pollutants processes and pathways in relation to urban stormwater pollution. This study has created new knowledge in relation to pollutant processes and transport pathways encompassing atmospheric pollutants, atmospheric deposition and build-up on ground surfaces of traffic generated key pollutants. The research study was primarily based on in-depth experimental investigations. This thesis describes the extensive knowledge created relating to the processes of atmospheric pollutant build-up, atmospheric deposition and road surface build-up and establishing their relationships as a chain of processes. The analysis of atmospheric deposition revealed that both traffic and land use related sources contribute total suspended particulate matter (TSP) to the atmosphere. Traffic sources become dominant during weekdays whereas land use related sources become dominant during weekends due to the reduction in traffic sources. The analysis further concluded that atmospheric TSP, polycyclic aromatic hydrocarbons (PAHs) and heavy metals (HMs) concentrations are highly influenced by total average daily heavy duty traffic, traffic congestion and the fraction of commercial and industrial land uses. A set of mathematical equation were developed to predict TSP, PAHs and HMs concentrations in the atmosphere based on the influential traffic and land use related parameters. Dry deposition samples were collected for different antecedent dry days and wet deposition samples were collected immediately after rainfall events. The dry deposition was found to increase with the antecedent dry days and consisted of relatively coarser particles (greater than 1.4 ìm) when compared to wet deposition. The wet deposition showed a strong affinity to rainfall depth, but was not related to the antecedent dry period. It was also found that smaller size particles (less than 1.4 ìm) travel much longer distances from the source and deposit mainly with the wet deposition. Pollutants in wet deposition are less sensitive to the source characteristics compared to dry deposition. Atmospheric deposition of HMs is not directly influenced by land use but rather by proximity to high emission sources such as highways. Therefore, it is important to consider atmospheric deposition as a key pollutant source to urban stormwater in the vicinity of these types of sources. Build-up was analysed for five different particle size fractions, namely, <1 ìm, 1-75 ìm, 75-150 ìm, 150-300 ìm and >300 ìm for solids, PAHs and HMs. The outcomes of the study indicated that PAHs and HMs in the <75 ìm size fraction are generated mainly by traffic related activities whereas the > 150 ìm size fraction is generated by both traffic and land use related sources. Atmospheric deposition is an important source for HMs build-up on roads, whereas the contribution of PAHs from atmospheric sources is limited. A comprehensive approach was developed to predict traffic and other land use related pollutants in urban stormwater based on traffic and other land use characteristics. This approach primarily included the development of a set of mathematical equations to predict traffic generated pollutants by linking traffic and land use characteristics to stormwater quality through mathematical modelling. The outcomes of this research will contribute to the design of appropriate treatment systems to safeguard urban receiving water quality for future traffic growth scenarios. The „real world. application of knowledge generated was demonstrated through mathematical modelling of solids in urban stormwater, accounting for the variability in traffic and land use characteristics.

A potential HIV epidemic among male street laborers in urban Vietnam

Background: Mass migration to Asian cities is a defining phenomenon of the present age, as hundreds of millions of people move from rural areas or between cities in search of economic prosperity. Although many do prosper, large numbers of people experience significant social disadvantage. This is especially the case among poorly educated, migrant unskilled unregistered male laborers who do much of the manual work throughout the cities. These men are at significant risk for many health problems, including HIV infection. However, to date there has been little research in developing countries to explain the determinants of this risk, and thereby to suggest feasible preventive strategies. Objectives and Methodology: Using combined qualitative and quantitative methods, the aim of this study was to explore the social contexts that affect health vulnerabilities and to develop conceptual models to predict risk behaviors for HIV [illicit drug use, unsafe sex, and non-testing for HIV] among male street laborers in Hanoi, Vietnam. Qualitative Research: Sixteen qualitative interviews revealed a complex variety of life experiences, beliefs and knowledge deficits that render these mostly poor and minimally educated men vulnerable to health problems including HIV infection. This study formed a conceptual model of numerous stressors related to migrants’ life experiences in urban space, including physical, financial and social factors. A wide range of coping strategies were adopted to deal with stressors – including problem-focused coping (PFC) and emotion-focused coping (EFC), pro-social and anti-social, active and passive. These men reported difficulty in coping with stressors because they had weak social networks and lacked support from formal systems. A second conceptual model emerged that highlighted equivalent influences of individual psychological factors, social integration, social barriers, and accessibility regarding drug use and sexual risk behavior. Psychological dimensions such as tedium, distress, fatalism and revenge, were important. There were strong effects of collective decision-making and fear of social isolation on shaping risk behaviors. These exploratory qualitative interviews helped to develop a culturally appropriate instrument for the quantitative survey and informed theoretical models of the factors that affect risk behaviors for HIV infection. Quantitative Research: The Information-Motivation-Behavioral Skills (IMB) model was adopted as the theoretical framework for a large-scale survey. It was modified to suit the contexts of these Vietnamese men. By doing a social mapping technique, 450 male street laborers were interviewed in Hanoi, Vietnam. The survey revealed that the risk of acquiring and transmitting HIV was high among these men. One in every 12 men reported homosexual or bisexual behavior. These men on average had 3 partners within the preceding year, and condom use was inconsistent. One third had had sex with commercial sex workers (CSW) and only 30% of them reported condom use; 17% used illicit drugs sometimes, with 66.7% of them frequently sharing injecting equipment with peers. Despite the risks, only 19.8% of men had been tested for HIV during the previous 12 months. These men have limited HIV knowledge and only moderate motivation and perceived behavioral skills for protective behavior. Although rural-to-urban migration was not associated with sexual risk behavior, three elements of the IMB model and depression associated with the process of mobility were significant determinants of sexual behavior. A modified model that incorporated IMB elements and psychosocial stress was found to be a better fit than the original IMB model alone in predicting protected sex behavior among the men. Men who were less psychologically and socially stressed, better informed and motivated for HIV prevention were more likely to demonstrate behavioral skills, and in turn were more likely to engage in safer sexual behavior. With regard to drug use, although the conventional model accounted for slightly less variance than the modified IMB model, data were of better fit for the conventional model. Multivariate analyses revealed that men who originated from urban areas, those who were homo- or bi-sexually identified and had better knowledge and skills for HIV prevention were more likely to access HIV testing, while men who had more sexual partners and those who did not use a condom for sex with CSW were least likely to take a test. The modified IMB model provided a better fit than the conventional model, as it explained a greater variance in HIV testing. Conclusions and Implications: This research helps to highlight a potential hidden HIV epidemic among street male, unskilled, unregistered laborers. This group has multiple vulnerabilities to HIV infection through both their partners and peers. However, most do not know their HIV status and have limited knowledge about preventing infection. This is the first application of a modified IMB model of risk behaviors for HIV such as drug use, condom use, and uptake of HIV testing to research with male street laborers in urban settings. The study demonstrated that while the extended IMB model had better fit than the conventional version in explaining the behaviors of safe sex and HIV testing, it was not so for drug use. The results provide interesting directions for future research and suggest ways to effectively design intervention strategies. The findings should shed light on culturally appropriate HIV preventive education and support programs for these men. As Vietnam has much in common with other developing countries in Southeast Asia, this research provides evidence for policy and practice that may be useful for public health systems in similar countries.

The lived world of older urban Australians: relating everyday living to GPS tracking data

Neighbourhood like the concept of liveability is usually measured by either subjective indicators using surveys of residents’ perceptions or by objective means using secondary data or relative weights for objective indicators of the urban environment. Rarely, have objective and subjective indicators been related to one another in order to understand what constitutes a liveable urban neighbourhood both spatially and behaviourally. This paper explores the use of qualitative (diaries, in-depth interviews) and quantitative (Global Positioning Systems, Geographical Information Systems mapping) liveability research data to examine the perceptions and behaviour of 12 older residents living in six high density urban areas of Brisbane. Older urban Australians are one of the two principal groups highly attracted to high density urban living. The strength of the relationship between the qualitative and quantitative measures was examined. Results of the research indicate a weak relationship between subjective and objective indicators. Linking the two methods (quantitative and qualitative) is important in obtaining a greater understanding of human behaviour and the lived world of older urban Australians and in providing a wider picture of the urban neighbourhood.

Particle nucleation in urban subtropical atmosphere

New particle formation (NPF) and growth have been observed in different environments all around the world and NPF affects the environment by forming cloud condensation nuclei (CCN). Detailed characterisation of NPF events in a subtropical urban environment is the main aim of this study. Particle size distribution (PSD) of atmospheric aerosol particles in range 9-414 nm were measured using a Scanning Mobility Particle Sizer (SMPS), within the framework of the “Ultrafine Particles from Traffic Emissions and Children’s Health” (UPTECH) study, which seeks to determine the relationship between exposure to traffic related ultrafine particles and children’s health (http://www.ilaqh.qut. edu.au/Misc/UPTECH%20Home.htm). The UPTECH study includes measurements of air quality, meteorological and traffic parameters in 25 randomly selected state primary school within the Brisbane metropolitan area, in Queensland, Australia. Measurements at 17 schools have been completed so far.

An integrated approach to supporting land-use decisions in site redevelopment for urban renewal in Hong Kong

Urban renewal is a significant issue in developed urban areas, with a particular problem for urban planners being redevelopment of land to meet demand whilst ensuring compatibility with existing land use. This paper presents a geographic information systems (GIS)-based decision support tool (called LUDS) to quantitatively assess land-use suitability for site redevelopment in urban renewal areas. This consists of a model for the suitability analysis and an affiliated land-information database for residential, commercial, industrial, G/I/C (government/institution/community) and open space land uses. Development has occurred with support from interviews with industry experts, focus group meetings and an experimental trial, combined with several advanced techniques and tools, including GIS data processing and spatial analysis, multi-criterion analysis, as well as the AHP method for constructing the model and database. As demonstrated in the trial, LUDS assists planners in making land-use decisions and supports the planning process in assessing urban land-use suitability for site redevelopment. Moreover, it facilitates public consultation (participatory planning) by providing stakeholders with an explicit understanding of planners' views.

Editorial : forecasting urban air quality

Air pollution has significant impacts on both the environment and human health. Therefore, urban areas have received ever growing attention, because they not only have the highest concentrations of air pollutants, but they also have the highest human population. In modern societies, urban air quality (UAQ) is routinely evaluated and local authorities provide regular reports to the public about current UAQ levels. Both local and international authorities also recommended that some air pollutant concentrations remain below a certain level, with the aim of reducing emissions and improving the air quality, both in urban areas and on a more regional scale. In some countries, protocols aimed at reducing emissions have come in force as a result of international agreements.

Study of new particle formation in subtropical urban environment in Brisbane, Australia

Atmospheric ultrafine particles play an important role in affecting human health, altering climate and degrading visibility. Numerous studies have been conducted to better understand the formation process of these particles, including field measurements, laboratory chamber studies and mathematical modeling approaches. Field studies on new particle formation found that formation processes were significantly affected by atmospheric conditions, such as the availability of particle precursors and meteorological conditions. However, those studies were mainly carried out in rural areas of the northern hemisphere and information on new particle formation in urban areas, especially those in subtropical regions, is limited. In general, subtropical regions display a higher level of solar radiation, along with stronger photochemical reactivity, than those regions investigated in previous studies. However, based on the results of these studies, the mechanisms involved in the new particle formation process remain unclear, particularly in the Southern Hemisphere. Therefore, in order to fill this gap in knowledge, a new particle formation study was conducted in a subtropical urban area in the Southern Hemisphere during 2009, which measured particle size distribution in different locations in Brisbane, Australia. Characterisation of nucleation events was conducted at the campus building of the Queensland University of Technology (QUT), located in an urban area of Brisbane. Overall, the annual average number concentrations of ultrafine, Aitken and nucleation mode particles were found to be 9.3 x 103, 3.7 x 103 and 5.6 x 103 cm-3, respectively. This was comparable to levels measured in urban areas of northern Europe, but lower than those from polluted urban areas such as the Yangtze River Delta, China and Huelva and Santa Cruz de Tenerife, Spain. Average particle number concentration (PNC) in the Brisbane region did not show significant seasonal variation, however a relatively large variation was observed during the warmer season. Diurnal variation of Aitken and nucleation mode particles displayed different patterns, which suggested that direct vehicle exhaust emissions were a major contributor of Aitken mode particles, while nucleation mode particles originated from vehicle exhaust emissions in the morning and photochemical production at around noon. A total of 65 nucleation events were observed during 2009, in which 40 events were classified as nucleation growth events and the remainder were nucleation burst events. An interesting observation in this study was that all nucleation growth events were associated with vehicle exhaust emission plumes, while the nucleation burst events were associated with industrial emission plumes from an industrial area. The average particle growth rate for nucleation events was found to be 4.6 nm hr-1 (ranging from 1.79-7.78 nm hr-1), which is comparable to other urban studies conducted in the United States, while monthly particle growth rates were found to be positively related to monthly solar radiation (r = 0.76, p <0.05). The particle growth rate values reported in this work are the first of their kind to be reported for the subtropical urban area of Australia. Furthermore, the influence of nucleation events on PNC within the urban airshed was also investigated. PNC was simultaneously measured at urban (QUT), roadside (Woolloongabba) and semi-urban (Rocklea) sites in Brisbane during 2009. Total PNC at these sites was found to be significantly affected by regional nucleation events. The relative fractions of PNC to total daily PNC observed at QUT, Woolloongabba and Rocklea were found to be 12%, 9% and 14%, respectively, during regional nucleation events. These values were higher than those observed as a result of vehicle exhaust emissions during weekday mornings, which ranged from 5.1-5.5% at QUT and Woolloongabba. In addition, PNC in the semi-urban area of Rocklea increased by a factor of 15.4 when it was upwind from urban pollution sources under the influence of nucleation burst events. Finally, we investigated the influence of sulfuric acid on new particle formation in the study region. A H2SO4 proxy was calculated by using [SO2], solar radiation and particle condensation sink data to represent the new particle production strength for the urban, roadside and semi-urban areas of Brisbane during the period June-July of 2009. The temporal variations of the H2SO4 proxies and the nucleation mode particle concentration were found to be in phase during nucleation events in the urban and roadside areas. In contrast, the peak of proxy concentration occurred 1-2 hr prior to the observed peak in nucleation mode particle concentration at the downwind semi-urban area of Brisbane. A moderate to strong linear relationship was found between the proxy and the freshly formed particles, with r2 values of 0.26-0.77 during the nucleation events. In addition, the log[H2SO4 proxy] required to produce new particles was found to be ~1.0 ppb Wm-2 s and below 0.5 ppb Wm-2 s for the urban and semi-urban areas, respectively. The particle growth rates were similar during nucleation events at the three study locations, with an average value of 2.7 ± 0.5 nm hr-1. This result suggested that a similar nucleation mechanism dominated in the study region, which was strongly related to sulphuric acid concentration, however the relationship between the proxy and PNC was poor in the semi-urban area of Rocklea. This can be explained by the fact that the nucleation process was initiated upwind of the site and the resultant particles were transported via the wind to Rocklea. This explanation is also supported by the higher geometric mean diameter value observed for particles during the nucleation event and the time lag relationship between the H2SO4 proxy and PNC observed at Rocklea. In summary, particle size distribution was continuously measured in a subtropical urban area of southern hemisphere during 2009, the findings from which formed the first particle size distribution dataset in the study region. The characteristics of nucleation events in the Brisbane region were quantified and the properties of the nucleation growth and burst events are discussed in detail using a case studies approach. To further investigate the influence of nucleation events on PNC in the study region, PNC was simultaneously measured at three locations to examine the spatial variation of PNC during the regional nucleation events. In addition, the impact of upwind urban pollution on the downwind semi-urban area was quantified during these nucleation events. Sulphuric acid was found to be an important factor influencing new particle formation in the urban and roadside areas of the study region, however, a direct relationship with nucleation events at the semi-urban site was not observed. This study provided an overview of new particle formation in the Brisbane region, and its influence on PNC in the surrounding area. The findings of this work are the first of their kind for an urban area in the southern hemisphere.

Rejuvenating lost and disused space within Fortitude Valley : a study into the effectiveness of urban greenery in subtropical public space

An issue gaining prominence in our urban environments in the notion of lost space, the undesirable urban areas that are in need of redesign, commonly caused by a focus on development as individual architectural entities, without a greater view of the urban environment as a holistic entity. Within the context of South East Queensland, the suburb of Fortitude Valley has been earmarked for development as an extension of the current CBD. With lost and disused spaces already existing throughout the suburb due to rapid growth and mismatched developments, recent planning regimes have proposed rejuvenation in the form of proposals that echo typologies from other Australian regions, such as the laneway typology from Melbourne. Opportunities exist in these spaces for design approaches that relate specifically to the individual and unique subtropical character of the area. This research explores the relationship between innovative approaches towards urban greenery as a means to rejuvenate lost and disused public space, and its suitability within a subtropical climate, specifically focused within the suburb of Fortitude Valley. A trend gaining prominence is the notion of biophilic cities; cities that integrate urban greenery as a means to provide vibrant public spaces, and meet the growing aesthetic, social, cultural and economic needs of our cities. Through analysis of case studies showcasing greenery in an inventive way, observations of public using subtropical public space, and a discussion of the current policy frameworks at place within Fortitude Valley, innovative uses of urban greenery is proposed as viable placemaking technique in subtropical urban environments.

A methodology to develop an urban transport disadvantage framework : the case of Brisbane, Australia

Most individuals travel in order to participate in a network of activities which are important for attaining a good standard of living. Because such activities are commonly widely dispersed and not located locally, regular access to a vehicle is important to avoid exclusion. However, planning transport system provisions that can engage members of society in an acceptable degree of activity participation remains a great challenge. The main challenges in most cities of the world are due to significant population growth and rapid urbanisation which produces increased demand for transport. Keeping pace with these challenges in most urban areas is difficult due to the widening gap between supply and demand for transport systems which places the urban population at a transport disadvantage. The key element in mitigating the issue of urban transport disadvantage is to accurately identify the urban transport disadvantaged. Although wide-ranging variables and multi-dimensional methods have been used to identify this group, variables are commonly selected using ad-hoc techniques and unsound methods. This poses questions of whether the current variables used are accurately linked with urban transport disadvantage, and the effectiveness of the current policies. To fill these gaps, the research conducted for this thesis develops an operational urban transport disadvantage framework (UTDAF) based on key statistical urban transport disadvantage variables to accurately identify the urban transport disadvantaged. The thesis develops a methodology based on qualitative and quantitative statistical approaches to develop an urban transport disadvantage framework designed to accurately identify urban transport disadvantage. The reliability and the applicability of the methodology developed is the prime concern rather than the accuracy of the estimations. Relevant concepts that impact on urban transport disadvantage identification and measurement and a wide range of urban transport disadvantage variables were identified through a review of the existing literature. Based on the reviews, a conceptual urban transport disadvantage framework was developed based on the causal theory. Variables identified during the literature review were selected and consolidated based on the recommendations of international and local experts during the Delphi study. Following the literature review, the conceptual urban transport disadvantage framework was statistically assessed to identify key variables. Using the statistical outputs, the key variables were weighted and aggregated to form the UTDAF. Before the variable's weights were finalised, they were adjusted based on results of correlation analysis between elements forming the framework to improve the framework's accuracy. The UTDAF was then applied to three contextual conditions to determine the framework's effectiveness in identifying urban transport disadvantage. The development of the framework is likely to be a robust application measure for policy makers to justify infrastructure investments and to generate awareness about the issue of urban transport disadvantage.

Atmospheric particles as a pollutant source in the urban water environment in Sri Lanka – current research trends and future directions

Human and ecosystem health impacts imposed by water pollution are a major problem in the urban areas of Sri Lanka. A primary source of pollutants to urban water sources is atmospheric particles. Hence, it is important to develop a detailed understanding of atmospheric particle characteristics, their sources of origin and the transport pathways. Several research studies have been conducted in Sri Lanka on atmospheric pollution and these studies have tended to differ in their scope, study region and the investigated pollutants. The objectives of this paper are: (1) to report the outcomes of a detailed state-of-art literature review of atmospheric pollution related studies in Sri Lanka to understand the current trends and (2) to discuss the future research activities necessary to generate the important knowledge required for the development of effective strategies to control the adverse impacts of atmospheric pollution on urban waterways.

Vote with your feet : hyperlocal public polling for urban screens

Technological advances have led to an ongoing spread of public displays in urban areas. However, they still mostly show passive content such as commercials and digital signage. Researchers took notice of their potential to spark situated civic discourse in public space and have begun working on interactive public display applications. Attracting people’s attention and providing a low barrier for user participation have been identified as major challenges in their design. This thesis presents Vote With Your Feet, a hyperlocal public polling tool for urban screens allowing users to express their opinions. Similar to vox populi interviews on TV or polls on news websites, the tool is meant to reflect the mindset of the community on topics such as current affairs, cultural identity and local matters. It shows one Yes/No question at a time and enables users to vote by stepping on one of two tangible buttons on the ground. This user interface was introduced to attract people’s attention and to lower participation barriers. Vote With Your Feet was informed by a user-centred design approach that included a focus group, expert interviews and extensive preliminary user studies in the wild. Deployed at a bus stop, Vote With Your Feet was evaluated in a field study over the course of several days. Observations of people and interviews with 30 participants revealed that the novel interaction technology was perceived as inviting and that Vote With Your Feet can spark discussions among co-located people.

A parcel-scale assessment tool to measure sustainability through urban ecosystem components : the MUSIX model

In recent years a number of urban sustainability assessment frameworks are developed to better inform policy formulation and decision-making processes. This paper introduces one of these attempts in developing a comprehensive assessment tool—i.e., Micro-level Urban-ecosystem Sustainability IndeX (MUSIX). Being an indicator-based indexing model, MUSIX investigates the environmental impacts of land-uses on urban sustainability by measuring urban ecosystem components in local scale. The paper presents the methodology of MUSIX and demonstrates the performance of the model in a pilot test-bed—i.e., in Gold Coast, Australia. The model provides useful insights on the sustainability performance of the test-bed area. The parcel-scale findings of the indicators are used to identify local problems considering six main issues of urban development—i.e., hydrology; ecology; pollution; location; design, and; efficiency. The composite index score is used to propose betterment strategies to guide the development of local area plans in conjunction with the City's Planning Scheme. In overall, this study has shown that parcel-scale environmental data provides an overview of the local sustainability in urban areas as in the example of Gold Coast, which can also be used for setting environmental policy, objectives and targets.

Mathematical relationships for metal build-up on urban road surfaces based on traffic and land use characteristics

The study investigated the influence of traffic and land use parameters on metal build-up on urban road surfaces. Mathematical relationships were developed to predict metals originating from fuel combustion and vehicle wear. The analysis undertaken found that nickel and chromium originate from exhaust emissions, lead, copper and zinc from vehicle wear, cadmium from both exhaust and wear and manganese from geogenic sources. Land use does not demonstrate a clear pattern in relation to the metal build-up process, though its inherent characteristics such as traffic activities exert influence. The equation derived for fuel related metal load has high cross-validated coefficient of determination (Q2) and low Standard Error of Cross-Validation (SECV) values indicates that the model is reliable, while the equation derived for wear-related metal load has low Q2 and high SECV values suggesting its use only in preliminary investigations. Relative Prediction Error values for both equations are considered to be well within the error limits for a complex system such as an urban road surface. These equations will be beneficial for developing reliable stormwater treatment strategies in urban areas which specifically focus on mitigation of metal pollution.

Food in the city : urban food movements and the (re)imagining of urban spaces

Ethical food movements are growing in number throughout Australia. Amongst these diverse movements are urban agriculture initiatives, which articulate a multitude of social and environmental values. Yet, despite the long history of production and exchange of food in urban areas, planners (and others) often overlook its significance. To assist in addressing this oversight, we take the case study of Melbourne to examine the ways in which participants in urban agriculture are re-imagining urban spaces and the future of agriculture and food systems in Australia. We demonstrate that urban food advocates' politics and practices both challenge and resist the enclosure of urban spaces. This creates new frontiers that transgress social, political, ecological and economic boundaries and edges. These transgressions or counter-enclosures articulate new visions for secure and just food systems and, in so doing, offer insights to assist planners in ensuring Australian cities support socially just and environmentally responsible food systems.

Exploring pedestrian accessibility and walkability : insight from public place observations in inner-urban higher density Brisbane, Australia

As planners work to create more sustainable and liveable urban environments, a priority is to transition away from prioritising the automobile and towards enhancing the pedestrian experience. Thus, this research explores the experience of pedestrian accessibility in inner-urban higher-density Brisbane in Australia, drawing on findings from semi-structured in-depth interviews with 24 residents and over 100 hours of public place observations in three case-study neighbourhoods. The interviews took place in residents homes and explored their experience of higher density living and their neighbourhood, whilst observations were recorded through a combination of methods including photographs, sketch maps, recordings and field journals. Observation locations included retail and commercial space, roads, parkland and open space, with multiple observations at each location. A thematic analysis identified common themes in both interviews and the observations, with this paper focusing on residents’ lived experience in urban built environments. This analysis revealed that pedestrian accessibility is linked to access to local amenities and direct routes, aesthetics, sense of community, ownership of space and safety. In particular, observations revealed how pedestrian accessibility and route-taking works with, against or in spite of the design features of urban environments, as well as the importance of the social use of the built environment. Residents spoke about although walking quick and preferred for local amenities, the decision to walk was moderated by factors such as time of day and perceived safety. Measures to ensure and improve the pedestrian accessibility of urban areas needs to take into account the propensity for people to prefer and improvise direct routes (often to the detriment of traffic safety considerations), the importance of ongoing maintenance and upgrading of walking infrastructure and the importance of aesthetically pleasing and safe walking environments. By combining interviews and observations, this research highlights the current dominance of the automobile culture in Brisbane and the layers of meaning, experiences and complexity hidden within the pedestrian experience.