Laboratory verification of predicted permanent deformation in asphalt materials following climate change.

In the past a change in temperature of 5°C most often occurred over intervals of thousands of years. According to estimates by the IPCC, in the XXI century is expected an increase in average temperatures in Europe between 1.8 and 4.0°C in the best case caused by emissions of carbon dioxide and other GHG from human activities. As well as on the environment and economic context, global warming will have effects even on road safety. Several studies have already shown how increasing temperature may cause a worsening of some types of road surface damages, especially rutting, a permanent deformation of the road structures consisting in the formation of a longitudinal depression in the wheelpath, mostly due to the rheological behavior of bitumen. This deformation evolves during the hot season because of the heating capacity of the asphalt layers, in fact, the road surface temperature is up to 24°C higher than air. In this thesis, through the use of Wheeltrack test, it was studied the behavior of some types of asphalt concrete mixtures subjected to fatigue testing at different temperatures. The objectives of this study are: to determine the strain variation of different bituminous mixture subjected to fatigue testing at different temperature conditions; to investigate the effect of aggregates, bitumen and mixtures’ characteristics on rutting. Samples were made in the laboratory mostly using an already prepared mixtures, the others preparing the asphalt concrete from the grading curve and bitumen content. The same procedure was performed for each specimen: preparation, compaction using the roller compactor, cooling and heating before the test. The tests were carried out at 40 - 50 - 60°C in order to obtain the evolution of deformation with temperature variation, except some mixtures for which the tests were carried out only at 50°C. In the elaboration of the results were considered testing parameters, component properties and the characteristics of the mixture. Among the testing parameters, temperature was varied for each sample. The mixtures responded to this variation with a different behavior (linear logarithmic and exponential) not directly correlated with the asphalt characteristics; the others parameters as load, passage frequency and test condition were kept constant. According to the results obtained, the main contribution to deformation is due to the type of binder used, it was found that the modified bitumen have a better response than the same mixtures containing traditional bitumen; to the porosity which affects negatively the behavior of the samples and to the homogeneity ceteris paribus. The granulometric composition did not seem to have interfered with the results. Overall has emerged at working temperature, a decisive importance of bitumen composition, than the other characteristics of the mixture, that tends to disappear with heating in favor of increased dependence of rutting resistance from the granulometric composition of the sample considered. In particular it is essential, rather than the mechanical characteristics of the binder, its chemical properties given by the polymeric modification. To confirm some considered results, the maximum bulk density and the air voids content were determined. Tests have been conducted in the laboratories of the Civil Engineering Department at NTNU in Trondheim according to European Standards.

La valutazione della sicurezza delle strade esistenti: Il contributo del mobile eye detector.

L’incidente stradale è la conseguenza di uno o più errori all'interno di un sistema complesso, in cui l'uomo rappresenta la principale causa d’incidentalità. Spesso ciò che può apparire a una prima analisi un errore dell’utente, in realtà può essere collegato a problemi di progettazione e gestione dell’infrastruttura. Per massimizzare i risultati nel campo della sicurezza stradale, occorre valutare il “sistema strada” in ogni suo elemento. Per raggiungere questi obiettivi le analisi di sicurezza giocano un ruolo fondamentale. Il Road Safety Review consente di individuare nel tracciato la presenza di situazioni di rischio, in modo tale da eliminarli o attenuarli prima che diano luogo ad incidenti. Il Ministero delle Infrastrutture e dei Trasporti ha emanato le "Linee guida per la gestione della sicurezza delle infrastrutture stradali". Secondo queste Linee Guida l'uomo detiene un ruolo centrale nel sistema. L'uomo deve adattare il suo comportamento, in funzione del veicolo condotto e delle condizioni ambientali. Diventa indispensabile integrare le analisi di sicurezza con il fattore uomo. Obiettivo della tesi è analizzare la sicurezza di un’infrastruttura viaria esistente integrando i risultati ottenuti dal Road Safety Review con metodologie innovative che tengano conto del comportamento degli utenti durante la guida. È stata realizzata una sperimentazione in sito che ha coinvolto un campione formato da 6 soggetti. Ognuno di essi ha percorso il tronco stradale, della SP26 "Valle del Lavino", in provincia di Bologna. La strada, richiede interventi di adeguamento e messa in sicurezza poiché risulta la terza tratta stradale a maggior costo sociale di tutta la rete provinciale. La sperimentazione ha previsto due fasi: la prima, in cui è stato condotto il Road Safety Review . La seconda, in cui ogni soggetto ha guidato lungo il tronco stradale, indossando il Mobile Eye-XG, un'innovativa strumentazione eye tracking in grado di tracciare l’occhio umano e i suoi movimenti.

La valutazione della sicurezza degli utenti deboli in prossimita degli attraversamenti pedonali: Il contributo del mobile eye detector

Lo studio effettuato si inserisce all’interno di una collaborazione tra il DICAM e la Provincia di Bologna ed ha come obiettivo l’analisi di sicurezza della SP26 “Valle del Lavino”, poichè risulta la terza tratta stradale a maggior costo sociale di tutta la rete provinciale. Il rapporto di analisi redatto a seguito del Road Safety Review ha infatti evidenziato numerosi deficit in termini di sicurezza dell’infrastruttura, tra cui gli attraversamenti pedonali. Obiettivo specifico della tesi è stato quello di valutare lo stato attuale di sicurezza degli attraversamenti pedonali presenti lungo il tracciato stradale in esame, in maniera tale da individuare, sulla base di una correlazione fra l’ubicazione degli attraversamenti stessi e il comportamento degli utenti alla guida dei veicoli, le intersezioni pedonali più gravosi, che per questo, in un piano di riqualifica della tratta stradale, richiederebbero opportuni interventi di adeguamento e messa in sicurezza. Con questa finalità è stata programmata ed eseguita una campagna di prove su strada che ha coinvolto un campione di 10 utenti, aventi determinati requisiti di base, del tutto ignari dell’obiettivo che si voleva perseguire e inesperti del tracciato di prova. La sperimentazione ha previsto l’impiego, fondamentale, di metodologie innovative, quali il V-Box e il Mobile Eye Detector, in grado di tener conto del comportamento degli utenti alla guida: il primo permette di rilevare l’andamento delle velocità dei partecipanti lungo il tracciato, il secondo restituisce il tracciamento del punto di vista del conducente alla guida. A ciascun partecipante è stato richiesto di condurre un veicolo, non di loro proprietà, per l’intero tratto della SP26 posto esame, compreso tra la progressiva 0+000, in comune di Zola Predosa, e la progressiva 19+200, in località Badia (comune di Monte San pietro), in andata e in ritorno per un complessivo di 38,4 km di tracciato da esaminare. Al conducente alla guida è stato richiesto di indossare durante tutta la guida l’occhiale Mobile Eye mentre l’auto di prova è stata dotata della strumentazione V-Box.

Formula Zero: Traduzione trilingue inglese-italiano-spagnolo di un policy statement sulla sicurezza stradale della Federazione Internazionale dell'Automobile (FIA)

The aim of this dissertation is to provide a trilingual translation from English into Italian and from Italian into Spanish of a policy statement from the Fédération Internationale de l’Automobile (FIA) regarding road safety. The document, named “Formula Zero: a strategy for reducing fatalities and injuries on track and road”, was published in June 2000 and involves an approach about road safety inspired by another approach introduced in Sweden called ‘Vision Zero’. This work consists of six sections. The first chapter introduces the main purposes and activities of the Federation, as well as the institutions related to it and Vision Zero. The second chapter presents the main lexical, morphosyntactic and stylistic features of the institutional texts and special languages. In particular, the text contains technical nomenclature of transports and elements of sport language, especially regarding motor sport and Formula One. In the third chapter, the methodology is explained, with all the resources used during the preliminary phase and the translation, including corpora, glossaries, expert consultancy and specialised sites. The fourth chapter focuses on the morphosyntactic and terminology features contained in the text, while the fifth chapter presents the source text and the target texts. The final chapter deals with all the translation strategies that are applied, alongside with all the challenging elements detected. Therefore, the dissertation concludes with some theoretical and practical considerations about the role of inverse translation and English as Lingua Franca (ELF), by comparing the text translated into Spanish to the original in English, using Italian as a lingua franca.

Vision and night driving abilities of elderly drivers

OBJECTIVE: In this article, we review the impact of vision on older people's night driving abilities. Driving is the preferred and primary mode of transport for older people. It is a complex activity where intact vision is seminal for road safety. Night driving requires mesopic rather than scotopic vision, because there is always some light available when driving at night. Scotopic refers to night vision, photopic refers to vision under well-lit conditions, and mesopic vision is a combination of photopic and scotopic vision in low but not quite dark lighting situations. With increasing age, mesopic vision decreases and glare sensitivity increases, even in the absence of ocular diseases. Because of the increasing number of elderly drivers, more drivers are affected by night vision difficulties. Vision tests, which accurately predict night driving ability, are therefore of great interest. METHODS: We reviewed existing literature on age-related influences on vision and vision tests that correlate or predict night driving ability. RESULTS: We identified several studies that investigated the relationship between vision tests and night driving. These studies found correlations between impaired mesopic vision or increased glare sensitivity and impaired night driving, but no correlation was found among other tests; for example, useful field of view or visual field. The correlation between photopic visual acuity, the most commonly used test when assessing elderly drivers, and night driving ability has not yet been fully clarified. CONCLUSIONS: Photopic visual acuity alone is not a good predictor of night driving ability. Mesopic visual acuity and glare sensitivity seem relevant for night driving. Due to the small number of studies evaluating predictors for night driving ability, further research is needed.

Metodología de evaluación de la seguridad vial en intersecciones basada en el análisis cuantitativo de conflictos entre vehículos

El modo tradicional de estimar el nivel de seguridad vial es el registro de accidentes de tráfico, sin embargo son altamente variables, aleatorios y necesitan un periodo de registro de al menos 3 años. Existen metodologías preventivas en las cuales no es necesario que ocurra un accidente para determinar el nivel de seguridad de una intersección, como lo es la técnica de los conflictos de tráfico, que introduce las mediciones alternativas de seguridad como cuantificadoras del riesgo de accidente. El objetivo general de la tesis es establecer una metodología que permita clasificar el riesgo en intersecciones interurbanas, en función del análisis de conflictos entre vehículos, realizado mediante las variables alternativas o indirectas de seguridad vial. La metodología para el análisis y evaluación temprana de la seguridad en una intersección, estará basada en dos medidas alternativas de seguridad: el tiempo hasta la colisión y el tiempo posterior a la invasión de la trayectoria. El desarrollo experimental se realizó mediante estudios de campo, para la parte exploratoria de la investigación, se seleccionaron 3 intersecciones interurbanas en forma de T donde se obtuvieron las variables que caracterizan los conflictos entre vehículos; luego mediante técnicas de análisis multivariante, se obtuvo los modelos de clasificación del riesgo cualitativo y cuantitativo. Para la homologación y el estudio final de concordancia entre el índice propuesto y el modelo de clasificación, se desarrollaron nuevos estudios de campo en 6 intersecciones interurbanas en forma de T. El índice de riesgo obtenido resulta una herramienta muy útil para realizar evaluaciones rápidas conducentes a estimar la peligrosidad de una intersección en T, debido a lo simple y económico que resulta obtener los registros de datos en campo, por medio de una rápida capacitación a operarios; la elaboración del informe de resultados debe ser por un especialista. Los índices de riesgo obtenidos muestran que las variables originales más influyentes son las mediciones de tiempo. Se pudo determinar que los valores más altos del índice de riesgo están relacionados a un mayor riesgo de que un conflicto termine en accidente. Dentro de este índice, la única variable cuyo aporte es proporcionalmente directo es la velocidad de aproximación, lo que concuerda con lo que sucede en un conflicto, pues una velocidad excesiva se manifiesta como un claro factor de riesgo ya que potencia todos los fallos humanos en la conducción. Una de las principales aportaciones de esta tesis doctoral a la ingeniería de carreteras, es la posibilidad de aplicación de la metodología por parte de administraciones de carreteras locales, las cuales muchas veces cuentan con recursos de inversión limitados para efectuar estudios preventivos, sobretodo en países en vías de desarrollo. La evaluación del riesgo de una intersección luego de una mejora en cuanto a infraestructura y/o dispositivos de control de tráfico, al igual que un análisis antes – después, pero sin realizar una comparación mediante la ocurrencia de accidentes, sino que por medio de la técnica de conflictos de tráfico, se puede convertir en una aplicación directa y económica. Además, se pudo comprobar que el análisis de componentes principales utilizado en la creación del índice de riesgo de la intersección, es una herramienta útil para resumir todo el conjunto de mediciones que son posibles de obtener con la técnica de conflictos de tráfico y que permiten el diagnóstico del riesgo de accidentalidad en una intersección. En cuanto a la metodología para la homologación de los modelos, se pudo establecer la validez y confiabilidad al conjunto de respuestas entregadas por los observadores en el registro de datos en campo, ya que los resultados de la validación establecen que la medición de concordancia de las respuestas entregadas por los modelos y lo observado, son significativas y sugieren una alta coincidencia entre ellos. ABSTRACT The traditional way of estimating road safety level is the record of occurrence of traffic accidents; however, they are highly variable, random, and require a recording period of at least three years. There are preventive methods which do not need an accident to determine the road safety level of an intersection, such as traffic conflict technique, which introduces surrogate safety measures as parameters for the evaluation of accident risks. The general objective of the thesis is to establish a methodology that will allow the classification of risk at interurban intersections as a function of the analysis of conflicts between vehicles performed by means of surrogate road safety variables. The proposal of a methodology for the analysis and early evaluation of safety at an intersection will be based on two surrogate safety measures: the time to collision and the post encroachment time. On the other hand, the experimental development has taken place by means of field studies in which the exploratory part of the investigation selected three interurban T-intersections where the application of the traffic conflict technique gave variables that characterize the conflicts between vehicles; then, using multivariate analysis techniques, the models for the classification of qualitative and quantitative risk were obtained. With the models new field studies were carried out at six interurban Tintersections with the purpose of developing the homologation and the final study of the agreement between the proposed index and the classification model. The risk index obtained is a very useful tool for making rapid evaluations to estimate the hazard of a T-intersection, as well as for getting simply and economically the field data records after a fast training of the workers and then preparing the report of results by a specialist. The risk indices obtained show that the most influential original variables are the measurements of time. It was determined that the highest risk index values are related with greater risk of a conflict resulting in an accident. Within this index, the only variable whose contribution is proportionally direct is the approach speed, in agreement with what happens in a conflict, because excessive speed appears as a clear risk factor at an intersection because it intensifies all the human driving faults. One of the main contributions of this doctoral thesis to road engineering is the possibility of applying the methodology by local road administrations, which very often have limited investment resources to carry out these kinds of preventive studies, particularly in developing countries. The evaluation of the risk at an intersection after an improvement in terms of infrastructure and/or traffic control devices, the same as a before/after analysis, without comparison of accident occurrence but by means of the traffic conflict technique, can become a direct and economical application. It is also shown that main components analysis used for producing the risk index of the intersection is a useful tool for summarizing the whole set of measurements that can be obtained with the traffic conflict technique and allow diagnosing accident risk at an intersection. As to the methodology for the homologation of the models, the validity and reliability of the set of responses delivered by the observers recording the field data could be established, because the results of the validation show that agreement between the observations and the responses delivered by the models is significant and highly coincident.

Floating car data augmentation based on infrastructure sensors and neural networks

The development of new-generation intelligent vehicle technologies will lead to a better level of road safety and CO2 emission reductions. However, the weak point of all these systems is their need for comprehensive and reliable data. For traffic data acquisition, two sources are currently available: 1) infrastructure sensors and 2) floating vehicles. The former consists of a set of fixed point detectors installed in the roads, and the latter consists of the use of mobile probe vehicles as mobile sensors. However, both systems still have some deficiencies. The infrastructure sensors retrieve information fromstatic points of the road, which are spaced, in some cases, kilometers apart. This means that the picture of the actual traffic situation is not a real one. This deficiency is corrected by floating cars, which retrieve dynamic information on the traffic situation. Unfortunately, the number of floating data vehicles currently available is too small and insufficient to give a complete picture of the road traffic. In this paper, we present a floating car data (FCD) augmentation system that combines information fromfloating data vehicles and infrastructure sensors, and that, by using neural networks, is capable of incrementing the amount of FCD with virtual information. This system has been implemented and tested on actual roads, and the results show little difference between the data supplied by the floating vehicles and the virtual vehicles.

Nueva disposición de sistemas de contención de vehículos en medianas de autovía: New practices for median barriers of highways

La siniestralidad por salida izquierda de vía en carreteras de gran capacidad es un problema que, además de las dramáticas situaciones a las que da lugar, inflige a la sociedad elevados costes. Por ello, debe prestarse una intensa atención al diseño de las medianas y a la disposición de barreras en ellas, con el objetivo de evitar que se produzcan este tipo de accidentes y limitar las consecuencias de los que aún así tengan lugar. Habitualmente las medianas de autovías se diseñan aplicando casi sistemáticamente los parámetros mínimos exigidos normativamente y generalmente con barreras de seguridad adosadas o muy próximas a uno de los arcenes interiores. Sin embargo, tanto las recomendaciones técnicas nacionales como la bibliografía internacional recomiendan llevar a cabo un estudio económico de alternativas antes que colocar barreras y, si está justificada su disposición, alejarla de la calzada disponiéndola próxima al eje de la mediana. En esta tesis se analizan las ventajas y limitaciones que tiene la disposición de barrera próxima al eje de la mediana. Se ha investigado sobre el comportamiento de los vehículos al circular por la mediana y se muestra cómo se ha instalado en la obra de la autovía A‐40, Tramo: Villarrubia de Santiago‐Santa Cruz de la Zarza, destacando los aspectos más novedosos y llamativos pero que se ajustan a las mejores prácticas en la materia y también a la normativa de aplicación. ABSTRACT Many dramatic situations are caused by cross‐median traffic accidents which imply high costs for society, both in human and economic terms. It is therefore important that special attention should be paid to the design of highway medians and to the installation of safety barriers so as to avoid these kinds of incidents and to reduce their consequences. Highway median are usually designed with the application of minimum parameters, according to regulations, with the installation of safety barriers against or close to the inside border. However, Spanish technical regulations and international bibliography recommend a prior study to be carried out with the purpose of finding alternatives to this installation of safety barriers and if necessary, the installation of the safety barrier close to the centre of the median. This thesis directs its analysis towards the advantages and restrictions of installing the safety barrier close to the centre of the median. Research has shown vehicle response when within the median and we show the installation of safety barriers in the A‐40 highway stretch: Villarrubia de Santiago – Santa Cruz de la Zarza, highlighting the aspects that should be taken into account as best practices for road safety and technical regulations.

Formulación de incentivos óptimos y viables para la mejora de la seguridad vial en concesiones de carreteras

La evolución de los roles de la Administración y empresas en la prestación de servicios públicos, así como las crecientes restricciones presupuestarias para financiarlos, están propiciando una cada vez mayor utilización del sistema concesional para la financiación y gestión de carreteras. Ante esta situación, cabe cuestionarse si la regulación de las prestaciones a obtener se está introduciendo de forma adecuada en los contratos. Uno de los aspectos más relevantes en este sentido es el relacionado con la seguridad de la infraestructura, sobre el cual la empresa concesionaria tiene capacidad de actuación pero, en un sentido económico estricto, pocos incentivos para mejorarla. Todo ello a pesar de los elevados costes sociales derivados de la accidentalidad. Esta tesis analiza la idoneidad de los indicadores e incentivos de seguridad vial que se vienen aplicando en concesiones de carreteras, encontrándose una gran heterogeneidad e incluso incorrecciones técnicas en su formulación. Además se pone de manifiesto la poca vinculación que tienen con la estructura de costes y beneficios de las actuaciones de mejora de seguridad vial, por lo que su introducción en los contratos resulta anodina. Con el objeto de superar esta situación, en esta tesis se analizan en profundidad los aspectos que intervienen en la formulación de indicadores e incentivos de seguridad vial. De este análisis se deduce la ecuación que liga, por tipología de carretera, el beneficio social derivado del nivel de seguridad de la carretera y el coste para alcanzarlo. A través de esta ecuación se determina el nivel de seguridad óptimo desde el punto de vista económico‐social. La investigación continúa extrapolando métodos de la teoría microeconómica de incentivos al campo de las concesiones de carreteras, a fin de determinar la formulación del incentivo de seguridad vial teóricamente óptimo. Asimismo, la tesis toma en consideración la experiencia en la aplicación práctica de incentivos en concesiones vigentes, realizándose una propuesta para superar las controversias que se están produciendo actualmente en España. Además, se ha simulado la aplicación de la formulación propuesta a diversas concesiones con un doble objetivo: verificar la viabilidad económica de su aplicación y corroborar en qué medida se adecua mejor al óptimo económico‐social. Como resultado, se proponen un indicador y un incentivo concretos que inducen a las concesionarias a orientar su gestión hacia la consecución del nivel de seguridad vial óptimo desde el punto de vista económico‐social, todo ello dentro de un marco de viabilidad presupuestaria. Changes in the roles of Government and the Private Sector in the provision of public services along with the budget constraints to finance them are resulting in an increasing use of the concession system for financing and managing roads. Taking this into account, the question is whether the regulation of quality criteria is being properly introduced in the contracts or not. One of the most important aspects at this respect is the road safety. On the one hand, concessionaires are able to manage this aspect up to a point. On the other hand, from an strict economic point of view, they have little incentive to improve it, despite the high social costs of accidents. This thesis has analyzed the suitability of indicators and incentives usually introduced in road concession contracts, finding high heterogeneity, and even technical inaccuracies on their formulation. It has also been found the lack of connection between these incentives and the costs of measures to improve road safety, therefore they are not expected to fulfil their purpose. In order to overcome this situation, this thesis firstly analyzes in depth the issues involved in the development of road safety indicators and incentives. This analysis yields the equation which links the social benefit derived from the level of road safety and the cost to achieve it. In its turn, through this equation it is possible to meet the optimal road safety level from the socio‐economic point of view. Secondly, this thesis extrapolates microeconomic methods to the field of highway concessions, with the aim of determining the formulation of the optimal road safety incentive. Furthermore, the thesis takes into account the experience in the practical application of incentives on existing concessions, performing a proposal to settle the disputes between concessionaires and the Public Administrations. Finally, the thesis simulates the implementation of the proposed indicator and incentive to real concessions with the aim of verifying the economic feasibility of their application and confirming how they match the socio‐economic optimum. As a result, this thesis proposes an indicator and incentive that induce companies to drive the management of the concession towards achieving the optimal road safety level, all within a framework of the budgetary feasibility.

Diseño de un modelo para la identificación y análisis de tramos de carreteras sin accidentes : una nueva visión de la seguridad vial

El planteamiento tradicional de análisis de la accidentalidad en carretera pasa por la consideración de herramientas paliativas, como son la identificación y gestión de los puntos negros o tramos de concentración de accidentes, o preventivas, como las auditorías e inspecciones de seguridad vial. En esta tesis doctoral se presenta un planteamiento complementario a estas herramientas, desde una perspectiva novedosa: la consideración de los tramos donde no se producen accidentes; son los denominados Tramos Blancos. La tesis persigue demostrar que existen determinados parámetros del diseño de las carreteras y del tráfico que, bajo características generales similares de las vías, tienen influencia en el hecho de que se produzcan o no accidentes, adicionalmente a la exposición al riesgo, como factor principal, y a otros factores. La propia definición de los Tramos Blancos, entendidos como tramos de carreteras de longitud representativa donde no se han producido accidentes con víctimas mortales o heridos graves durante un periodo largo de tiempo, garantiza que esta situación no se produzca como consecuencia de la aleatoriedad de los accidentes, sino que pudiera deberse a una confluencia específica de determinados parámetros de la geometría de la vía y del tráfico total y de vehículos pesados. Para el desarrollo de esta investigación se han considerado la red de autopistas de peaje y las carreteras convencionales de la Red del Estado de España, que supone un total de 17.000 kilómetros, y los datos de accidentes con víctimas mortales y heridos graves en el periodo 2006-2010, ambos incluidos, en estas redes (un total de 10.000 accidentes). La red viaria objeto de análisis supone el 65% de la longitud de la Red de Carreteras del Estado, por la que circula el 33% de su tráfico; en ella se produjeron en el año 2013 el 47% de los accidentes con víctimas y el 60% de las víctimas mortales de la Red de Carreteras del Estado. Durante la investigación se ha desarrollado una base de datos de 250.130 registros y más de 3.5 millones de datos en el caso de las autopistas de peaje de la Red de Carreteras del Estado y de 935.402 registros y más de 14 millones de datos en el caso de la red convencional del Estado analizada. Tanto las autopistas de peaje como las carreteras convencionales han sido clasificadas según sus características de tráfico, de manera que se valoren vías con nivel de exposición al riesgo similar. Para cada tipología de vía, se ha definido como longitud de referencia para que un tramo se considere Tramo Blanco la longitud igual al percentil 95 de las longitudes de tramos sin accidentes con heridos graves o víctimas mortales durante el periodo 2006-2010. En el caso de las autopistas de peaje, en la tipología que ha sido considerada para la definición del modelo, esta longitud de referencia se estableció en 14.5 kilómetros, mientras que en el caso de las carreteras convencionales, se estableció en 7.75 kilómetros. Para cada uno de los tipos de vía considerados se han construido una base de datos en la que se han incluido las variables de existencia o no de Tramo Blanco, así como las variables de tráfico (intensidad media diaria total, intensidad de vehículos pesados y porcentaje de vehículos pesados ), la velocidad media y las variables de geometría (número de carriles, ancho de carril, ancho de arcén derecho e izquierdo, ancho de calzada y plataforma, radio, peralte, pendiente y visibilidad directa e inversa en los casos disponibles); como variables adicionales, se han incluido el número de accidentes con víctimas, los fallecidos y heridos graves, índices de peligrosidad, índices de mortalidad y exposición al riesgo. Los trabajos desarrollados para explicar la presencia de Tramos Blancos en la red de autopistas de peaje han permitido establecer las diferencias entre los valores medios de las variables de tráfico y diseño geométrico en Tramos Blancos respecto a tramos no blancos y comprobar que estas diferencias son significativas. Así mismo, se ha podido calibrar un modelo de regresión logística que explica parcialmente la existencia de Tramos Blancos, para rangos de tráfico inferiores a 10.000 vehículos diarios y para tráficos entre 10.000 y 15.000 vehículos diarios. Para el primer grupo (menos de 10.000 vehículos al día), las variables que han demostrado tener una mayor influencia en la existencia de Tramo Blanco son la velocidad media de circulación, el ancho de carril, el ancho de arcén izquierdo y el porcentaje de vehículos pesados. Para el segundo grupo (entre 10.000 y 15.000 vehículos al día), las variables independientes más influyentes en la existencia de Tramo Blanco han sido la velocidad de circulación, el ancho de calzada y el porcentaje de vehículos pesados. En el caso de las carreteras convencionales, los diferentes análisis realizados no han permitido identificar un modelo que consiga una buena clasificación de los Tramos Blancos. Aun así, se puede afirmar que los valores medios de las variables de intensidad de tráfico, radio, visibilidad, peralte y pendiente presentan diferencias significativas en los Tramos Blancos respecto a los no blancos, que varían en función de la intensidad de tráfico. Los resultados obtenidos deben considerarse como la conclusión de un análisis preliminar, dado que existen otros parámetros, tanto de diseño de la vía como de la circulación, el entorno, el factor humano o el vehículo que podrían tener una influencia en el hecho que se analiza, y no se han considerado por no disponer de esta información. En esta misma línea, el análisis de las circunstancias que rodean al viaje que el usuario de la vía realiza, su tipología y motivación es una fuente de información de interés de la que no se tienen datos y que permitiría mejorar el análisis de accidentalidad en general, y en particular el de esta investigación. Adicionalmente, se reconocen limitaciones en el desarrollo de esta investigación, en las que sería preciso profundizar en el futuro, reconociendo así nuevas líneas de investigación de interés. The traditional approach to road accidents analysis has been based in the use of palliative tools, such as black spot (or road sections) identification and management, or preventive tools, such as road safety audits and inspections. This thesis shows a complementary approach to the existing tools, from a new perspective: the consideration of road sections where no accidents have occurred; these are the so-called White Road Sections. The aim of this thesis is to show that there are certain design parameters and traffic characteristics which, under similar circumstances for roads, have influence in the fact that accidents occur, in addition to the main factor, which is the risk exposure, and others. White Road Sections, defined as road sections of a representative length, where no fatal accidents or accidents involving serious injured have happened during a long period of time, should not be a product of randomness of accidents; on the contrary, they might be the consequence of a confluence of specific parameters of road geometry, traffic volumes and heavy vehicles traffic volumes. For this research, the toll motorway network and single-carriageway network of the Spanish National Road Network have been considered, which is a total of 17.000 kilometers; fatal accidents and those involving serious injured from the period 2006-2010 have been considered (a total number of 10.000 accidents). The road network covered means 65% of the total length of the National Road Network, which allocates 33% of traffic volume; 47% of accidents with victims and 60% of fatalities happened in these road networks during 2013. During the research, a database of 250.130 registers and more than 3.5 million data for toll motorways and 935.042 registers and more than 14 million data for single carriageways of the National Road Network was developed. Both toll motorways and single-carriageways have been classified according to their traffic characteristics, so that the analysis is performed over roads with similar risk exposure. For each road type, a reference length for White Road Section has been defined, as the 95 percentile of all road sections lengths without accidents (with fatalities or serious injured) for 2006-2010. For toll motorways, this reference length concluded to be 14.5 kilometers, while for single-carriageways, it was defined as 7.75 kilometers. A detailed database was developed for each type of road, including the variable “existence of White Road Section”, as well as variables of traffic (average daily traffic volume, heavy vehicles average daily traffic and percentage of heavy vehicles from the total traffic volume), average speed and geometry variables (number of lanes, width of lane, width of shoulders, carriageway width, platform width, radius, superelevation, slope and visibility); additional variables, such as number of accidents with victims, number of fatalities or serious injured, risk and fatality rates and risk exposure, have also been included. Research conducted for the explanation of the presence of White Road Sections in the toll motorway network have shown statistically significant differences in the average values of variables of traffic and geometric design in White Road Sections compared with other road sections. In addition, a binary logistic model for the partial explanation of the presence of White Road Sections was developed, for traffic volumes lower than 10.000 daily vehicles and for those running from 10.000 to 15.000 daily vehicles. For the first group, the most influent variables for the presence of White Road Sections were the average speed, width of lane, width of left shoulder and percentage of heavy vehicles. For the second group, the most influent variables were found to be average speed, carriageway width and percentage of heavy vehicles. For single-carriageways, the different analysis developed did not reach a proper model for the explanation of White Road Sections. However, it can be assumed that the average values of the variables of traffic volume, radius, visibility, superelevation and slope show significant differences in White Road Sections if compared with others, which also vary with traffic volumes. Results obtained should be considered as a conclusion of a preliminary analysis, as there are other parameters, not only design-related, but also regarding traffic, environment, human factor and vehicle which could have an influence in the fact under research, but this information has not been considered in the analysis, as it was not available. In parallel, the analysis of the circumstances around the trip, including its typology and motivation is an interesting source of information, from which data are not available; the availability of this information would be useful for the improvement of accident analysis, in general, and for this research work, in particular. In addition, there are some limitations in the development of the research work; it would be necessary to develop an in-depth analysis in the future, thus assuming new research lines of interest.

«Cidadania em Movimento» - Projeto de iIntervenção socioeducativa no bairro Las Palmeras em Córdoba, Espanha

Trabalho de projeto para a obtenção do grau de Mestre na área de Educação Social e Intervenção Comunitária

Trends in mortality due to motor vehicle traffic accident injuries between 1987 and 2011 in a Spanish region (Comunitat Valenciana)

Objective: To analyse the time evolution of the rates of mortality due to motor vehicle traffic accidents (MVTA) injuries that occurred among the general population of Comunitat Valenciana between 1987 and 2011, as well as to identify trend changes by sex and age group. Methods: An observational study of annual mortality trends between 1987 and 2011. We studied all deaths due to MVTA injuries that occurred during this period of time among the non-institutionalised population residing in Comunitat Valenciana (a Spanish Mediterranean region that had a population of 5,117,190 inhabitants in 2011). The rates of mortality due to MVTA injuries were calculated for each sex and year studied. These rates were standardised by age for the total population and for specific age groups using the direct method (age-standardised rate – ASR). Joinpoint regression models were used in order to detect significant trend changes. Additionally, the annual percentage change (APC) of the ASRs was calculated for each trend segment, which is reflected in statistically significant joinpoints. Results: For all ages, ASRs decrease greatly in both men and women (70% decrease between 1990 and 2011). In 1990 and 2011, men have rates of 36.5 and 5.2 per 100,000 men/year, respectively. In the same years, women have rates of 8.0 and 0.9 per 100,000 women/year, respectively. This decrease reaches up to 90% in the age group 15–34 years in both men and women. ASR ratios for men and women increased over time for all ages: this ratio was 3.9 in 1987; 4.6 in 1990; and 5.8 in 2011. For both men and women, there is a first significant segment (p < 0.05) with an increasing trend between 1987 and 1989–1990. After 1990, there are 3 segments with a significant decreasing APC (1990–1993, 1993–2005 and 2005–2011, in the case of men; and 1989–1996, 1999–2007 and 2007–2011, in the case of women). Conclusion: The risk of death due to motor vehicle traffic accidents injuries has decreased significantly, especially in the case of women, for the last 25 years in Comunitat Valenciana, mainly as of 2006. This may be a consequence of the road-safety measures that have been implemented in Spain and in Comunitat Valenciana since 2004. The economic crisis that this country has undergone since 2008 may have also been a contributing factor to this decrease. Despite the decrease, ASR ratios for men and women increased over time and it is still a high-risk cause of death among young men. It is thus important that the measures that helped decrease the risk of death are maintained and improved over time.

«Cidadania em Movimento» - Projeto de iIntervenção socioeducativa no bairro Las Palmeras em Córdoba, Espanha

Trabalho de projeto para a obtenção do grau de Mestre na área de Educação Social e Intervenção Comunitária

Segurança rodoviária infantil : conhecimentos e atitudes dos pais na utilização do sistema de retenção no recém-nascido

Enquadramento: A segurança é um direito da criança, que deve ser assegurado pelos pais e sociedade em geral, pois devido à sua vulnerabilidade estão sujeitas a um maior risco de lesões e morte. O transporte seguro de recém-nascidos/crianças em automóveis é uma preocupação, pois os acidentes de viação são a principal causa de mortalidade e morbilidade nesta faixa etária. Nos acidentes rodoviários, o uso correto de um sistema de retenção para crianças (SRC), desde o nascimento, constitui uma forma eficaz de proteção. Objetivos: Caracterizar os conhecimentos e atitudes dos pais no uso do SRC; analisar a influência do processo de aquisição e de informação dos pais sobre o uso do SRC; identificar a relação entre as variáveis sociodemográficas dos pais e o uso de SRC; determinar se os conhecimentos são mediadores das atitudes dos pais na utilização do SRC. Métodos: Estudo quantitativo, transversal, descritivo e correlacional, realizado numa amostra não probabilística, por conveniência de 112 pais de recém-nascidos, mães com média de idade de 30,37 anos (Dp=5,63) e pai 33,91 (Dp=6,09). Para recolha de informação utilizou-se um questionário, construído para o efeito, que os pais preencheram 24-48h após o parto durante os meses de março a maio de um centro hospitalar da região norte de Portugal. Resultados: Maioritariamente tinham como escolaridade o ensino secundário e entre 1 a 4 filhos. O SRC fazia parte do ―enxoval‖ do bebé em 54,5% dos participantes, destes, 72,3% já o tinha experimentado no automóvel e pretendiam usá-lo na alta desde a maternidade 97,3%. Contudo, apurou-se que apenas 47,3% o faria de forma adequada, apesar de 83% referir conhecer a legislação e todos reconhecerem que previne lesões em caso de acidente e 67% admitir ter conhecimentos adequados sobre SRC. Concluiu-se haver relação entre os conhecimentos e a idade e a escolaridade das mães, e pelos resultados obtidos, inferimos que melhores conhecimentos conduzem a melhores atitudes na utilização do SRC. Conclusões: Os resultados indicam que os conhecimentos dos pais sobre o uso adequado de SRC continuam insuficientes. Este facto justifica o investimento no ensino, treino e preparação dos pais para a alta segura desde a maternidade, momento particularmente sensível, e que será determinante nas atitudes de promoção da segurança rodoviária das crianças e adolescentes. Palavras-chave: Segurança; Recém-nascido; Sistema de retenção; Conhecimentos; Atitudes.